Characteristics of polyaniline anti-corrosive coatings with various primer coating resins(epoxy resin, urethane resin, and others) and top coating resins(epoxy and acrylic urethane resins) were investigated through adhesion, acid resistance, alkaline resistance, water resistance, and anti-corrosion tests. As a result, the anti-corrosive properties of the prepared coatings using polyaniline varied with the types of primer and top coating resins. In this condition, the properties of adhesion, chemical resistance, and water resistance were found to be very satisfactory when using emeraldine base (EB) of polyaniline blended with single-packaged urethane and acrylic urethane resins as the primer coatings, and using acrylic urethane resin as the top coatings. Also, the anti-corrosive function of these anti-corrosive coatings was well preserved for 1000 hr in the salt spray experiment.

We investigated heat stability of epoxy resin products and epoxy resin according to the influence hardener. The heat flow which shows the degree of thermal decomposition of the epoxy resin product and epoxy resin measured by using the differential scanning calorimeter (DSC). As a result, we found that in the case of heat stability for epoxy resin as hardener was added, the ratio of one to one (epoxy resin : hardener) was the most suitable in air condition and nitrogen atmosphere.

This study was aimed not only to develop the gill net and trap made of biodegradable monofilaments in order to prevent a ghost fishing and to protect marine ecosystem, but also to analyze their spinning process and physical properties. Results showed that the spinning speed of biodegradable polybutylene succinate(PBS) monofilament was estimated to be approximately 100m/min when spinning temperature and cooling water temperature were adjusted at 180℃ and 3℃, respectively. The breaking loads of PBS monofilaments were estimated to be 35.3kg/mm2 at Φ0.2mm, 46.5kg/mm2 at Φ0.3mm, and 49.7kg/mm2 at Φ0.4mm in the dry condition, respectively. However, its breaking loads in the wet condition were reduced by 2.4-5.5%, compared to those in the dry condition. The knotted strength of PBS monofilament at Φ0.2mm was estimated to be 98.6% of PE in the dry condition. The breaking load of PBS monofilament at Φ0.3mm was evaluated to be 81.8% of PA, and its softness showed 3 times less than that of PA in the wet condition. The breaking load of PBS monofilament at Φ0.4mm was 95.3% of PA, and its softness showed 1.6 times less than that of PA in the wet state. However, the load elastic elongations of two kinds of monofilaments were estimated to be 1% higher than that of PA.

Three different weather-resistant coatings were fabricated with the various weight ratios of a mill-base silicone/acrylic resin to let-down silicone /acrylic resin at 2:8, 3:7, and 4:6 respectively. The prepared coatings were tested to investigate the effect of composition of weather-resistant coatings on the physical properties. The thermal stability, salt spray exposure, and weather-resistance were improved with the increased silicone content. It was concluded that the optimum retio of mill-base silicone/acrylic resin to let-down silicone/acrylic resin would be 2:8 and the coating with 30 wt% of silicone content would have high weather-resistance.

음이온교환수지인 IRN-78및 IRN-77과의 혼합 수지를 액체 상태로 직접 분해 처리하기 위하여 Fenton 시약을 이용하였다. 개선된 분해방법의 특징은 수지를 먼저 건조시키고 용액을 수지에 완전히 흡수시킨 후 일정량의 를 첨가하여 분해반응을 유도하는 방법을 적용하였다. 촉매로서 및 IRN-77 수지의 분해시 사용한 를 각각 사용하여 각 이온교환수지의 단독 및 혼합수지의 분해에 필요한 적절한 촉매와 그의 농도 및 의 소요량을 측정하였다. IRN-78 수지에 대해 촉매를 사용한 경우, 초기 분해반응을 유도하기 위해 까지 가열이 필요하였으며, 반응유도시간은 촉매의 적정온도에서 약 20분 이내 개시되는 것으로 나타났다. 동 수지에 를 사용한 경우에는 가열 없이 즉시 분해반응이 진행되었으며 분해율도 수% 높게 나타났다. 결론적으로 IRN-78 및 IRN-77과의 혼합수지의 분해를 위한 최적 촉매는 로 나타났으며 가열하지 않고 상온에서 반응유도시간 없이 각 수지를 단독으로 분해한 경우보다 적은 양의 로 완전히 액상으로 분해시킬 수 있는 좋은 결과를 얻었다. 또한 이들 각각의 수지 및 혼합수지에 대한 적절한 촉매 및 적정 농도와 완전분해에 필요한 의 양을 제시하였다.

In order to prepare high-solid coatings, acrylic resins, HSCs [poly (EA/EMA/2-HEMA/CLA)] that contain 90% solid, were synthesized by copolymerization of ethyl acrylate (EA), ethyl methacrylate (EMA), 2-hydroxyethyl methacrylate (2-HEMA) and caprolactone acrylate (CLA). The high-solid coatings named as CHSCs (HSCs/HDI-trimer) were prepared by the curing reaction between the acrylic resins containing 90% solid contents and the isocyanates (HDI-trimer) curing agent room temperature. The curing behavior and various properties were examined on the film coated with the both high-solid coatings. The glass transition temperatures (Tg) of CHSCs increased proportionally with increasing the predicted Tg value by Fox equation, and had nothing to do with the solid contents. The prepared film showed good properties for 60˚ specular gloss, impact resistance, cross-hatch adhesion and heat resistance, and bad properties for pencil hardness, drying time, and pot-life. Among the film properties, the heat resistance was very excellent and could be explained by the introduction of functional monomers of CLA.

To prepare weather-resistant silicone/acrylic resin coatings for an architectural purpose, tetrapolymers were synthesized by a radical polymerization. 3-Methacryloxypropyltrimethoxysilane (MPTS) as a silicone monomer and n-butyl acrylate, methyl methacrylate, and n-butyl methacrylate as acrylic monomers were used. The compositions of monomers were adjusted to fix the glass transition temperature of acrylic polymer for 20℃. The composition of MPTS in the synthesized polymer were varied from 10 wt% to 30 wt%. On the basis of synthesized resin amber paints were prepared and their physical properties and effects for weatherability were examined. The presence of MPTS in silicone/acrylic resins generally resulted in low molecular weight and broad molecular weight distribution, and also lowered the viscosity of the copolymers. The coated films prepared from these resins showed good and balanced properties in general. Adhesion to the substrate was outstanding in particular. Weatherability tests were carried out in three different types such as outdoor exposure, QUV, and SWO. The test results showed that the silicone/acrylic resins containing 30 wt% of MPTS had weather-resistant properties.

양이온교환수지인 IRN-77을 직접 분해 처리하기 위하여 Fonton시약을 적용하였으며, 분해반응의 특징으로써 반응의 효율 및 안전을 위해 수지를 먼저 건조시키고 용액을 수지에 완전히 흡수시킨 후 를 첨가하는 방법을 적용하였다. 수지 분해반응의 특성은 반응이 개시되기까지 반응유도시간이 필요하였으며, 반응유도시간은 의 농도가 낮을수록 또한 의 초기 첨가량이 적을수록 길었다. 단위량의 수지를 분해하는데 적절한 반응조건으로서 의 농도는 0.9 M 및 15% 의 용액의 첨가량은 수지량에 대해 6-7배 비율로 나타났으며, 반응유도시간을 포함하여 1.5시간 이내에 완전 분해가 가능하였다. 의 첨가방법은 반응 초기 및 반응개시 후로 나누어 첨가하므로서 의 분해효율 및 첨가량을 최소화하였다. 가열효과로서 분해반응 개시 전에 비교적 낮은 온도인 정도로 가열하면 반응유도시간이 5분 이내로 단축되었으며, 수지의 양을 5g 및 10g 으로 증가시킨 결과, 의 첨가비율을 9-10배 정도로 증가시키면 완전분해가 가능하였다.

In order to prepare high-solid coatings, first acrylic resins (HSAs) which contain 80% solid were synthesized, and then the prepared resins were cured with isocyanate at room temperature. In the synthesis of HSAs, viscosity, number average molecular weight (Mn) and conversion were 1372~2700 cps, 1520~1650 and 83~87%, respectively. Among the four kinds of initiators used, tert-amylperoxy-2-ethyl hexanoate was the most proper one in the synthesis of HSAs. With increasing Tg values, viscosity increased rapidly and molecular weight increased slowly. As a result of the examination of coated films, it was found that 60˚ specular gloss, impact resistance, heat resistance and cross-hatch adhesion were good, and pencil hardness, drying time and pot life were poor.

중수로 원전내 여러 계통으로 부터 발생된 폐수지내에는 핵종이 다량 함유되어 있으며, Class A 및 C 폐기물로 분류되는 폐수지의 적정 처리 기술 개발을 위한 기초연구를 수행하였다. IRN-150 혼상 이온교환수지를 이용하여 비방사성 이온과 양이온의 흡착 특성 및 탈차용액을 이용한 이온의 제거 특성을 고찰하였다. IRN-150 수지의 이온의 흡착능은 이론값에 근접한 11 mg-C/g-IRN-150을 나타내었고, 양이온의 흡착 친화도를 단일성분 및 복합성분 시스템을 이용하여 분석하였다. 여러 가지 탈착용액을 이용한 폐수지로부터 이온의 제거 특성을 평가한 결과, 핵종을 전량 효과적으로 제거하기 위해서는 보다도 용액이 유리한 것으로 나타났다.

The high-solid coatings were prepared by blending the synthesized acrylic resin in the previous paper, and hexamethylene diisocyanate-trimer and curing it at room temperature. The characterization of the films of the prepared coatings was performed. The 60˚ specular gloss, impact resistance, cross-hatch adhesion, and heat resistance of the films proved to be good, and the pencil hardness, drying time, and pot-life proved to be slightly poor. From a viscoelastic measurement using a rigid-body pendulum, curing was accelerated with the Tg value.

최근 미국 ANL연구소가 개발한 다이포실 수지는 우라늄의 선택특성이 우수하나 수지의 형태가 분말형이므로 입상의 비드형으로 제조하기 위하여 다이포실 분말을 알기네이트상에 고정화하는 방법을 적용하였다. 생성된 비드의 우라늄에 대한 흡착특성을 측정한 결과, 소디움 알기네이트 자체도 우라늄 흡착특성을 최대 68%까지 나타낸 후 30% 수준으로 감소하였으며, 이는 흡착후 탈착하는 과정을 거쳐 평형에 이르는 것으로 사료된다. 또한 비드내 다이포실의 양이 증가할수록 우라늄의 흡착이 증가하며 최대 85 %정도의 흡착율을 나타내고 있다. 다이포실 수지만의 경우 반응초기에 급격한 흡착을 보이고 있으나 3일정도 이후에는 비드의 흡착율과 유사한 결과를 나타내고 있으며 비드내 함유된 순 다이포실량을 고려할 경우 알기네이트 자체의 흡착효과로 인해 비드의 흡착효율이 크게 상승되는 것으로 해석된다. 우라늄 농도의 영향은 농도의 증가에 따라 우라늄의 제거효율이 감소하였으며, 비드의 양을 2배로 증가시킨 결과 최대 90%이상의 제거효율을 얻었다. 결론적으로 다이포실 수지를 소디움 알기네이트상에 고정화하여 입자형의 비드로 제조하므로서 적은 양의 수지로 우라늄 제거특성이 우수한 비드를 얻을 수 있었으며 나아가서 연속공정에의 적용도 가능한 것으로 사료된다.

Preservation of wooden architecture by means of synthetic resin, is physical and chemical work. Synthetic resins are using for consolidation and restoration of decayed members. Since 1978, synthetic resin became useful preservation of architectural heritage in Korea. The first object was Chimgyeru of Songgwang-temple in Suncheon city. In the 1980s, have begun the care of materials for conservation on the architectural heritage, it was influenced according to authenticity of UNESCO Venice charter's principle, in 1964. In Korea, preservation of wooden architecture by means of synthetic resin that is sing many kinds of epoxies. Among the specific types of epoxies are araldite XN1023, SV427, etc. The use of synthetic resin have merits and demerits in the restoration for architectural heritage. The merit is that it is more smaller change with new members during preservation work. But the demerit is an irreversibility of the epoxy resin. In 1999, 'ICOMOS International Wood Committee' recommend contemporary materials and techniques, should be chosen and used with the greatest caution. And preservation work should reversible, as possible as technically. Therefore, should be data continous for preservation of wooden architecture by synthetic resin. Because data is very important work about a preservation of wooden architecture by synthetic resin. And should be try to think about new materials and techniques instead of synthetic resin, in the long view.

Acrylic resins (HSCs : EA/EMA/2-HEMA/CLA) which contain 80% solid content were synthesized by the copolymerization of monomers (ethyl acrylate, ethyl methacrylate, 2-hydroxyethyl methacrylate) and functional monomer (caprolactone acrylate : CLA) which improves the crosslinking density and physical properties of films. The physical properties of the prepared acrylic resins (HSCs) containing CLA, are as follows: viscosity 1440~2630 cps ; Mn 1590~1660 ; and conversions, 81~86%, respectively. From the correlation of Tg values, viscosities, and Mn of the HSCs, it was found thst viscosity and Mn increased with Tg value.