본 연구에서는 콘크리트 구조물의 내구성 고도화를 위하여 고속도로용 교각 기둥부에 대하여 내부 식성이 우수한 GFRP 보강근 적용하였으며, 설계적 분석, 축소모형 시험체 제작 및 성능 시험을 통하 여 실용화의 타당성를 검증하였다. 설계적으로 교각의 기둥부는 축방향 주철근을 GFRP 보강근으로 대체하였다. 일반적으로 GFRP는 압축부에 취약한 것으로 알려져 있으며, 국외 기준의 경우는 압축부 에 대하여 GFRP 보강근은 저항력이 없는 것으로 가정하고 있다. 본 연구에서는 탄성 교각에 대하여 기존 철근을 대체할 수 있는 GFRP 보강근의 설계적 방안 제시 및 실물 시험을 통한 성능 검증을 수 행하여 결과를 제시하였다. 본 연구 결과는 고속도로용 탄성 교각 기둥의 내구성 증진을 위한 설계 및 실용화에 있어 가능한 가이드라인을 제시할 것으로 기대된다. 다만, 본 연구에서 다룬 기둥부는 주철 근만을 GFRP 보강근으로 대체한 것으로, 향후 GFRP 나선형 보강근 등의 적용, GFRP의 축하중 분담 률 및 건조수축 크리프 특성, 기둥부의 최소 보강근비 산정 그리고 GFRP 보강근의 압축강도 측정법 등 상세 사항에 대한 추가적인 연구가 필요할 것이다.

The purpose of this study is to experimentally analyze the seismic performance of beam-column specimens with vertical irregular, which were reinforced with RHS (Replaceable steel haunch system). a steel haunch system. To evaluate the seismic performance of the RHS, three specimens were manufactured and subjected to cycle loading tests. Retrofitted specimens have different beam-upper column stiffness ratio as a variable. The stiffness ratio of beam-upper column were considered to be 1.2 and 0.84. As a result of the test, the specimen reinforced with RHS showed improved maximum load and effective stiffness, and energy dissipation capacity compared to the non-retrofitted specimen with same beam-upper column stiffness ratio. The specimen with 0.84 beam-upper column stiffness ratio showed improved performance than the specimen with 12.

Herein, the existing structural design criteria for highway bridge columns with hollow bars were analyzed. Expanding upon previous research focused on the performance analysis of the columns under compressive loads, load– displacement curves were evaluated and crack analysis was performed under cyclic transverse loads. A three-dimensional nonlinear finite-element structural analysis compared the structural performance of existing steel bars, same-reinforced hollow bars, and reduced hollow bars in detail. Results indicated that with regard to elastic or initial crack behavior, the existing steel bars can be replaced by the other bars. Future research should delve into inelastic behavior and strategies to ensure seismic performance.

As earthquakes have increased in Korea recently, people are paying attention to the seismic performance of buildings built in the past. Many school buildings in Korea were built based on standard drawings before the seismic design was applied. However, since school buildings are often designated as emergency evacuation facilities in case of disasters such as earthquakes, seismic evaluation and retrofit must be done quickly. This study investigated the failure modes among structural components (beams, columns, and joints), focusing on 1980s standard drawings for school buildings. The effects of column axial force, partial masonry infills, and different material strengths for concrete and rebar were considered for detailed evaluation. As a result, most of the joints were found to be the weakest among structural components. Column axial forces tended to make the joints more vulnerable, and partial masonry infills increased the possibility of joint failure and shear failure in columns.

The collapse of reinforced concrete (RC) frame buildings is mainly caused by the failure of columns. To prevent brittle failure of RC column, numerous studies have been conducted on the seismic performance of strengthened RC columns. Concrete jacketing method, which is one of the retrofitting method of RC members, can enhance strength and stiffness of original RC column with enlarged section and provide uniformly distributed lateral load capacity throughout the structure. The experimental studies have been conducted by many researchers to analyze seismic performance of seismic strengthened RC column. However, structures which have plan and vertical irregularities shows torsional behavior, and therefore it causes large deformation on RC column when subjected to seismic load. Thus, test results from concentric cyclic loading can be overestimated comparing to eccentric cyclic test results, In this paper, two kinds of eccentric loading pattern was suggested to analyze structural performance of RC columns, which are strengthened by concrete jacketing method with new details in jacketed section. Based on the results, it is concluded that specimens strengthened with new concrete jacketing method increased 830% of maximum load, 150% of maximum displacement and changed the failure modes of non-strengthened RC columns.

In the case of columns in buildings with soft story, the concentration of stress due to the difference in stiffness can damage the columns. The irregularity of buildings including soft story requires retrofit because combined load of compression, bending, shear, and torsion acts on the structure. Concrete jacketing is advantageous in securing the strength and stiffness of existing members. However, the brittleness of concrete make it difficult to secure ductility to resist the large deformation, and the complicated construction process for integrity between the existing member and extended section reduces the constructability. In this study, two types of Steel Grid Reinforcement (SGR), which are Steel Wire Mesh (SWM) for integrity and Steel Fiber Non-Shrinkage Mortar (SFNM) for crack resistance are proposed. One reinforced concrete (RC) column with non-seismic details and two columns retrofitted with each different types of proposed method were manufactured. Seismic performance was analyzed for cyclic loading test in which a combined load of compression, bending, shear, and torsion was applied. As a result of the experiment, specimens retrofitted with proposed concrete jacketing method showed 862% of maximum load, 188% of maximum displacement and 1,324% of stiffness compared to non-retrofitted specimen.

This paper presents the effect on the inelastic behavior and structural performance of concrete and filled steel pipe through a numerical method for reliable judgment under various load conditions of the CJS composite structural system. Variable values optimized for the CJS synthetic structural system and the effects of multiple variables used for finite element analysis to present analytical modeling were compared and analyzed with experimental results. The Winfrith concrete model was used as a concrete material model that describes the confinement effect well, and the concrete structure was modeled with solid elements. Through geometric analysis of shell and solid elements, rectangular steel pipe columns and steel elements were modeled as shell elements. In addition, the slip behavior of the joint between the concrete column and the rectangular steel pipe was described using the Surface-to-Surface function. After finite element analysis modeling, simulation was performed for cyclic loading after assuming that the lower part of the foundation was a pin in the same way as in the experiment. The analysis model was verified by comparing the calculated analysis results with the experimental results, focusing on initial stiffness, maximum strength, and energy dissipation capability.

모듈러 건축물은 철근콘크리트 및 철골 구조물에 비하여 상대적으로 경량이고, 단위 모듈간 기둥의 일체성을 기대하기 어려운 구조적 특성을 가진다. 이와 같은 구조적 특성은 모듈러 건축물의 높이가 높아짐에 따라 바람 및 지진과 같은 횡력저항성능에 직접적인 영향을 미친다. 본 연구에서는 횡력저항성능을 향상시키기 위해 긴장재를 활용한 모듈러 구조시스템을 제안하였다. 모듈러 구조시스템을 구성하는 주요 요소인 포스트텐션 기둥-바닥 접합부는 셀프 센터링 거동을 유도하기 위한 형상 및 상세를 가진다. 포스트텐션 기 둥-바닥 접합부의 이력 거동을 상세히 파악하기 위해 유한요소해석을 수행하였으며, 그 결과 초기 긴장력 및 보-기둥 접합부의 접합 조건에 따라 이력 거동은 확연한 차이를 보이는 것으로 나타났다.

콘크리트로 채워진 강관기둥은 많은 구조 시스템에서 기둥으로 널리 사용되며 강재가 항복하고 구속효과가 감소하여 국부 좌굴이 발생한다. 이러한 단점을 극복하기 위해 FRP를 보강하여 국부 좌굴을 지연시키는 방법을 제안한다. 이 논문은 반복 압축하에서 FRP로 보강된 CFT의 압축성능에 관한 것이다. 두 가지 유형의 FRP (Aramid FRP, SRF Polyester Belt)가 다양한 보강두께와 겹수로 CFT 외부에서 보강하여 비교 분석된다. 또한, CFRP에서 제안 및 사용된 공식에 기초하여 시험 기관의 실험 값을 평가하고 그것이 사용될 수 있는지를 결정할 것이다.

해양환경의 극한 환경조건에 노출 된 고정식 및 부유식 해양구조물의 안전성과 설계비용 효율성에 있어서 파랑-구조물 상 호작용의 정확한 예측은 중요하다. 본 연구에서는 규칙파 중 원형 기둥에 대한 파랑-구조물 상호작용을 해석하였다. 3차원 이상유동 (two-phase flow)을 해석하기 위해 오픈소스 전산유체역학 라이브러리인 오픈폼을 사용하였다. 4개의 원형기둥이 정사각형 배열을 이루 고 있을 때 규칙파의 입사각도에 따른 상호작용을 해석하였다. 원형 기둥 구조물에서의 wave run-up을 입사파의 기울기에 따라 비교하 였다. 원형 기둥과 입사파의 상호작용으로 인해 원형 기둥 사이에 높은 파가 생성되는 것을 확인하였다. 본 해석 결과는 구조물과 입 사파의 상호작용에 의한 air gap에 대한 연구의 기초자료로 활용될 것으로 기대된다.

When reinforcing an existing reinforced concrete beam-column building with a precast concrete panel, special connection between the PC member and the RC member is required to solve the time dependent deformation of the RC member and to receive the large shear forces. The aim of this study is to obtain the shear strength of upper connection between the existing RC beam-column and infilled PC wall panels in experimentally and theoretically. Thus, the static shear loading tests were conducted on the 6 specimens with the plate connection. Shear failure was resulted from the weakest portion of interior PC panel, exterior RC, and the connection, when the PC portion which located at the center of specimen was pulled upward from the bottom. T he experimental result was compared with analytical result from ACI 318M-14 Chapter 17 for the shear strength of post-installed anchor and PCI Handbook 7th edition 6.8 Structural Steel Corbel (PCI Design Handbook 7th edition, 2010) for the strength of cast-in H-beam. The analytical and experimental results show final failure at the same location. The failure loading of experiment showed larger than average 6% to that of the analysis.

In this study the structural performance of new composite column to composite beam connection was evaluated by cyclic tests. It is designed to be applied to various types of through type system to the bottom plate to view synthesis composite beam. A composite column is composed of a RC type column reinforced by steel angles which the end bends in each edge corners of column. also, A composite beam is composed of trussed type’s web, a bottom steel plate and reinforced by steel angles which the end bends in each edge corners of beam. 4 cyclic tests of the clarified structural performance of the connections are performed. All specimens that is apply reinforced concrete beam-column joints based on KBC2009 criteria was performed by cyclic test of column to beam. All specimens were exposed to be satisfied with the required ultimate strength.

To overcome the weakness of spread foundation in large space structure, the research of precast pile for replace spread foundation have been conducted. The new type of joint between PHC pile and steel column is named HAT Joint(Hollow hAlf-sphere cast-sTeel Joint). It connected PHC Pile by bolt that verification of bolt connection should be accomplished. In this paper, pull-out test and flexural performance for HAT Joint to verifying the bolt connection is explained. As a result, the pull-out and flexural capacities of bolt were checked to use in real structure. Furthermore, the equation of pull-out strength was proposed.

This paper presents a foundation pile to steel column connection that can resist large magnitude of moment and that can be easy installed. The developed joint has spherical shape and it is given the name HAT joint to mean Hallow half-sphere steel joint. Four types of HAT joints are developed. Namely, H-type, T-type, P-type and K-type. In this paper I will talk about the performance assessment of T-type(Tube Column) and P-type(Pile Column) of HAT joints with finite element analysis and experiment on a full scale model is presented.

Generally, the Load of upper structures is transferred to concrete foundations through columns supporting them. So, the anchor connection system is usually adopted in order to connect the columns and the concrete foundations. To apply this system, the column-foundation connections need to be designed with enough stiffness. This study was experimentally conducted to effectively improve the structural detail of circular CFT column-foundation connections, to which axial and lateral load simultaneously apply. For this study, the test specimen with a general anchor and an anchor frame, and the specimens with the high-tension bolt and inner reinforcement were fabricated. In addition, double base plates were adopted to have the enough stiffness of connections. The behavioral characteristics and the failure mode were investigated and compared, and the improvement of structural detail of circular CFT column-foundation connections was suggested.

최근, 모듈러 구조 시스템은 공기를 단축시킬 수 있는 장점으로 인해 건설 현장에 적용되고 있다. 모듈러 구조시스템은 단위 모듈로 구성되며, 모듈과 모듈의 볼트접합을 위해 보-기둥 접합부에 개구부를 가공하게 된다. 일반적으로 모듈러 구조시스템은 기존 철골모멘트골조와 유사한 하중전달체계를 가지는 것으로 가정하여 설계된다. 이와 같은 설계 가정의 타당성을 확보하기 위해, 단위 모듈의 보-기둥 접합부에 대한 회전 성능이 파악되어야 한다. 본 연구에서는 개구부의 구조적 영향이 고려된 접합부의 회전성능을 파악하기 위해 유한요소해석을 수행하였다. 해석결과 단위모듈은 충분한 변형능력을 가지고 안정적인 이력거동을 하는 것으로 나타났으며, 단위모듈의 접합부는 부분강접 접합부로 분류되었다. 또한 본 연구에서는 단위모듈의 비선형 골조 해석을 위한 간단한 스프링 모델을 개발하였으며, 단위 모듈의 비선형 이력 거동을 구현하기 위해 Ramberg-Osgood 이력 모델을 제시하였다.

This study carried out passenger safety assessment by real car crash simulation of composite post structures for road facilities. The effects of different material properties of composites for various parameters are studied using the LS-DYNA finite element program for this study. In this study, the existing finite element analysis of steel post structures using the LS-DYNA program is further extended to study dynamic behaviors of the structures made of various composite materials. The numerical results for various parameters are verified by comparing different models with displacements and stress distribution occurred in the post and car.

Main topics in this study is a new structural detail for connection between H-Steel or SRC column and flat plate slab. We carried out to evaluate the punching shear performance of H-steel or SRC column + RC slab system for vertical load and lateral load. From the test results structural characteristics - yield moment, yield rotation, maximum moment, deformation capabilities ect. - are obtained and evaluated. In this paper as a shear reinforcement for supporting region of plate closed stirrup type and shear band are used, and their test results are compared.

Generally, in the previous researches, it is found that a water droplet is respectively in Wenzel and Cassie-Baxter states on hydrophilic/hydrophobic rough surfaces. And Wenzel and Cassie-Baxter equations are used to estimate the apparent contact angle on the surfaces. However, difference between measured apparent contact angle and estimated apparent contact angle with the equations is recently reported and new model to estimate apparent contact angle on rough surfaces is proposed. In this study, wetting state and apparent contact angle on the surfaces with micro-pillars should be investigated to find solution of this argument. Using the high resolution microscope, the wetting state of the D.I.water droplet on the surface with micro-pillars was visualized and apparent contact angle of the D.I.water droplet was measured. On the basis of experimental data, the equations to estimate apparent contact angle were verificated and the general wetting characteristics on the surfaces with micro-pillars are finally classified.