In conventional construction methods, the slab-balcony junction often experiences thermal bridging. This phenomenon arises from the discontinuity of insulation materials, leading to energy loss and condensation that can compromise the structure's usability and durability. To address this issue, thermal break insulation systems were installed between the slab and balcony to effectively prevent thermal bridging and energy loss, thereby improving the overall energy efficiency of buildings. This study aims to enhance both the structural performance and thermal efficiency of slab-balcony connections in residential buildings. To assess the impact of the thermal break insulation system, two experimental specimens were prepared: one incorporating the system and the other without it. Experimental results confirmed that the inclusion of reinforcing bars significantly improved the connection's structural load-bearing capacity. Furthermore, thermal analysis revealed that the thermal break insulation system outperformed conventional insulation methods by reducing the thermal damage ratio and maintaining higher surface temperatures at the connection. In addition, a structural analysis using an FEM (finite element analysis) program was conducted to evaluate the load distribution across the specimens, demonstrating that the experimental data accurately predicted the structural behavior of the connections.

Small VTOL platforms envisioned for Urban Air Mobility (UAM) require compact and high–disk-loading propulsion systems, for which coaxial propellers are a suitable option. While counter-rotating coaxial propellers have been widely studied due to their torque-cancellation advantages, combined experimental and CFD-based research on coaxial co-rotating systems remains limited. This study investigates the aerodynamic performance of such a system using RANS-based CFD simulations, complemented by parallel experiments for validation. A pair of 18-inch, two-bladed propellers was arranged in a stacked layout, with mounting angle and inter-rotor spacing treated as key design variables. Results indicate that rotor–rotor interference leads to a maximum Figure of Merit (FoM) of 0.51 when the upper rotor leads at H/D = 0.07 and index angle of +15°. Increasing axial spacing generally improves the performance of both the upper and lower rotors, with the maximum thrust of 17.5N obtained at H/D = 0.07 and +45°. These performance trends were confirmed experimentally, and differences between CFD predictions and measurements remained within 5% for thrust and 6% for torque, demonstrating strong agreement. This study identifies influential design parameters for coaxial co-rotating propeller systems and provides a validated numerical methodology, offering a useful foundation for future high-efficiency Electric Distributed Propulsion System (EDPS) development.

To improve the seismic performance of a cabinet, a TMD was designed and its dynamic behavior was experimentally investigated as a basic study on vibration reduction. For TMD vibration test, a testing machine base, sliding base and jig were constructed. TMD and base were excited at the same frequency, and their natural frequencies showed a phase difference of approximately 90 degrees. The specifications of the experimental TMD were 20 kg mass, 10% damping ratio, and 7 L of oil. Seismic tests were conducted to investigate the dynamic behavior of the cabinet under earthquakes and the vibration characteristics of the cabinet with and without TMD. Vibration tests were conducted with the cabinet door fully closed, and the acceleration at the top of the cabinet was measured. The maximum acceleration was reduced by approximately 36% when TMD was installed compared to when it was not installed. The experimental results clearly demonstrated the effectiveness of TMD in reducing cabinet vibration.

본 연구는 강풍에 취약한 설비로 선정된 154kV 직선형 송전철탑을 대상으로 극한 풍하중에 대한 구조 성능을 검토하였다. 선행연 구에 따르면 송전철탑은 정면풍보다 45° 풍향에서 더 취약한 거동을 보이며, 이를 고려하여 ABAQUS를 이용한 Pushover 해석을 수 행하였다. 극한 풍속 조건에서의 취약 부재와 거동 특성을 분석한 후, 길이 차원에서 1/2 상사율을 적용한 부분축소모형을 제작하였 으며, 지압이음 조건과 마찰이음 조건으로 구분하였다. 또한 두 대의 가력기를 이용해 전체모델에서 산정된 수평력과 휨모멘트를 상 사법칙에 따라 재현하였다. 실험 결과, 볼트 체결력을 향상시킨 경우 항복변위는 약 30% 감소했으나 항복하중에는 큰 차이가 없었다. 특히 마찰이음 조건에서는 해석과 실험의 항복하중 및 항복변위가 모두 5% 이내의 오차를 보여 Pushover 해석의 신뢰성이 검증되었다. 향후 연구에서는 주요 부재의 보강 방안을 수립하고, 보강된 부분축소모형 실험을 통해 내풍 및 내진 성능 향상을 검증할 예정이다.

This study investigates the seismic performance of beam-column connections using Thin-Walled Steel Composite (TSC) beams and Prestressed Reinforced Concrete (PSRC) columns. TSC beams are constructed from U-shaped thin steel plates that are filled with concrete, allowing for composite action with slabs through the use of shear connectors. They are widely applied in industrial buildings due to excellent strength, stiffness, and constructability. However, slender web plates are prone to local buckling, which may compromise their performance during seismic events. To mitigate this issue, internal supports have been introduced to enhance web stability and concrete confinement. Cyclic loading tests on three specimens—with and without internal supports—demonstrated that the supports increased moment capacity, improved energy dissipation, and effectively reduced buckling. Even slender sections demonstrated performance comparable to that of compact sections. All specimens reached peak strength at a 2.44% rotation angle, with damage localized near the supports. A practical connection detail was also proposed, taking into account constructability and structural reliability. The results provide valuable guidance for the seismic design of composite systems in large-scale structures.

This study investigates the effects of canopy fabric material and vent diameter on the deployment performance of sea anchors for fishing operations through field experiments. Three canopy configurations were tested: polyamide (PA), polyester (PES), and a PA – PES alternating combination. Vent diameters of 80 cm and 40 cm were applied to each fabric as controlled structural factors. Deployment performance was evaluated from entrance diameter computed using four evenly spaced water level loggers, and maximum towing tension was recorded with a load cell. Key findings were discovered as follows: PES and the PA – PES mix achieved deployment diameter/ratio and maximum tension comparable to the current PA standard, indicating practical substitutability. PES also exhibited superior stability, showing reduced variability even with the smaller vent (a change in standard deviation ΔSD-1.75 cm). The mixed canopy maintained performance similar to PA. As expected, vent diameter systematically affected geometry and load (80 cm: 187 – 198 kgf vs. 40 cm: 249 – 268 kgf), underscoring the need to pair material selection with appropriate vent sizing. In conclusion, PES and mixed fabrics are viable alternatives to PA, and co-optimization of fabric choice and vent diameter can enhance sea-anchor performance, durability, and operational reliability for fishing operations.

원자력발전소에 설치되는 안전관련 기기는 높은 수준의 내진성능을 확보하여야 한다. 본 연구에서는 대표적인 안전관련 기기 인 전기 캐비닛을 대상으로, 열반(multi-bay) 구성 및 콘크리트 기초 열화와 같은 실제 설치 조건을 고려하여 내진성능을 평가하였다. 실제 현장에서는 전기 캐비닛이 열반 형태로 설치되는 경우가 많으며, 지지부 열화의 대표적 형태로 앵커 위치에서의 콘크리트 균열이 자주 발견된다. 이러한 조건을 반영하기 위하여, 앵커 위치에 균열 폭 0.5 mm 및 1.0 mm를 모사한 균열 기초와 건전한 기초를 대상 으로 실험체를 제작하였다. 실험체는 단순화한 전기 캐비닛 모델로서 단독(single-bay) 및 2기 열반(two-bay) 구성을 적용하였으며, 선설치 앵커로 고정 후 진동대를 이용한 한계상태 내진성능 실험을 수행하였다. 실험 결과, 균열이 없는 조건에서는 2기 열반 구성이 단독 구성보다 높은 내진성능을 보였다. 그러나 균열 조건에서는 2기 열반 구성에서 내진성능이 저하되는 경향이 나타난 반면, 단독 구성은 유의미한 성능 저하가 관찰되지 않았다.

Recently, steel dampers are widely used as seismic reinforcement devices. Steel dampers have the advantage of being easy to manufacture and being able to absorb a lot of energy through stable hysteresis behavior. However, there is a possibility that the steel damper may be damaged due to fatigue caused by repeated seismic loads. In this study, the seismic performance of steel slit dampers and engineering plastic slit dampers with different physical characteristics were compared and analyzed. It can be seen that the yield load of the steel slit damper, which has relatively high rigidity, is much larger than that of the engineering plastic slit damper. Therefore, the engineering plastic damper is more effective when applied to a structure that experiences a large displacement rather than a structure that experiences a large load.

For experimental studies on the production of MR fluid for MR dampers, MR fluid with a viscosity of 506 cP and a density of 2.6 g/cc was produced. In order for MR fluid to have suitable performance for MR dampers, it is important to select surfactants, magnetic particles, base oil, and characteristic additives to obtain high damping force and maintain physical and chemical properties. In order to investigate the redispersibility of MR fluid, viscosity, density, saturation magnetic flux density, dispersibility, and temperature effects were evaluated. A particle size distribution meter and a vibrating magnetometer were used, and a yield stress and redispersion device were developed to obtain the yield stress of the MR fluid. The recovery rate of MR fluid was approximately 97% at 0.2% succinic acid coating and 8% anti-settling agent. And when current is applied, the viscosity increases by more than 90% due to magnetic properties.

과거 지진 발생 시 구조요소에 비해 비구조요소에서 더 많은 피해가 발생하였다. 비구조요소의 손상은 건물 및 시설의 기능에 영향을 줄 뿐만 아니라 인명피해를 유발할 수 있다. 건축물 내진설계 기준에서는 피난경로상의 비구조요소는 내진설계 또는 검토가 필요하다. 국내에서는 경주지진 이후 피난경로에 위치할 수 있는 천장 시스템의 내진성능 검증이 활발히 진행되고 있다. 그러나 옥외 계단, 문 등에 설치되는 캐노피 시스템의 내진설계 및 검증은 미흡한 실정이다. 지진으로 인해 캐노피가 위치유지를 하지 못하여 탈락 하거나 손상될 경우, 피난경로가 차단되어 인명피해로 이어질 수 있으므로 내진설계 및 내진성능을 평가할 필요가 있다. 따라서 본 연구에서는 모듈형 캐노피 시스템을 개발하고, 주요 요소에 대한 구조실험을 수행하였으며, 기존의 캐노피 시스템과 그 성능을 비교분 석 하였다.

The seismic performance of lead-rubber bearings (LRBs) is significantly affected by both the axial force and loading rate they experience. Accurate assessment of LRBs’ seismic performance, therefore, requires realistic simulation of these forces and rates, as well as of the response of the isolated structure during seismic events. This study conducted a series of real-time hybrid simulations (RTHS) to evaluate the seismic behavior of LRBs in such conditions. The simulations focused on a two-span continuous bridge isolated by LRBs atop the central pier, exposed to horizontal and vertical ground motions. In the RTHS framework, the LRBs were physically tested in the laboratory, while the remainder of the bridge was numerically modeled. Findings from these simulations indicated that the vertical ground motion had a minimal effect on the lateral response of the bridge when isolated by LRBs.

The purpose of this study is to experimentally analyze the seismic performance of a vertical irregular beam-column specimen reinforced with RBS (Replaceable Steel Brace System), a steel brace system. To evaluate the seismic performance of RBS, three specimens were manufactured and subjected to cycle loading tests. The stiffness ratio of beam-upper column of the non-retrofitted specimen was 1.2, and those of the two retrofitted specimens were 1.2 and 0.84. The stiffness ratio of the beam-lower column of all specimens was 0.36. And the stiffness ratio were used for variable. As a result of the experiment, the specimen retrofitted with RBS showed improved maximum load, effective stiffness and energy dissipation capacity compared to the non-retrofitted specimen with the same beam-upper column stiffness ratio. The specimen with 0.84 beam-upper column stiffness ratio showed improved performance compared to the specimen with 1.2 stiffness ratio.

콘크리트 도로포장의 손상은 차량의 이동에 의한 진동, 겨울철 제설제 사용, 동결융해 작용 등이 주요 손상원인으로 나타나고 있다. 이러한 손상을 해결하기 위하여 열화 원인에 능동적으로 대응하는 보수재료 및 방법이 적용되어야 하나, 일반적으로 단면복구, 부분보 수를 반복적으로 사용함으로써, 지속적인 열화 현상의 발생으로 도로포장의 기능을 상실하게 된다. 또한, 기존에 사용되고 있는 보수 재료 중 무기계 보수재료는 폴리머 모르타르, 에폭시수지 모르타르 등이 있다. 이러한 재료는 높은 압축강도를 가지고 있으나, 취성 및 부착력이 약한 단점을 나타내고 있다. 따라서 본 연구에서는 보통포틀랜드시멘트(Ordinary Portland Cement), 칼슘알루미네이트계 재 료인 칼슘설포알루미네이트(Calcium Sulfo Aluminate) 및 비정질 알루미네이트(Amorphous Calcium Aluminate)를 사용한 보수 모르타르의 압축강도 및 내동해성을 평가하였다. 보수 모르타르의 압축강도를 분석한 결과, 비정질 알루미네이트를 사용한 보수모르타르의 압축강 도가 보통포틀랜드시멘트 및 칼슘설포알루미네이트를 사용한 보수 모르타르보다 우수하게 나타나는 것을 확인하였다. 한편, 보수 모르 타르의 내동해성 평가는 ASTM C 666 A법에 준하여 실험을 진행하였다. 그 결과, 칼슘설포알루미네이트 및 비정질 알루미네이트를 적용한 보수 모르타르의 상대동탄성계수가 300사이클에서 약 90%이상으로 나타나 보통포틀랜드시멘트를 사용한 보수 모르타르보다 우수한 내동해성을 나타내었다. 따라서, 칼슘설포알루미네이트 및 비정질 알루미네이트를 적용한 보수 모르타르는 우수한 압축강도 및 내동해성을 나타냄으로써 도로포장의 보수재료로 사용이 가능할 것으로 판단된다.

현대 건설산업 분야에서 철근콘크리트는 반영구적인 재료로 인식되어 가장 많이 사용되고 있다. 하지만 콘크리트의 노후화 및 수분 용해 현상 등으로 생긴 균열을 통해 강재의 부식이 발생하게 된다. 이러한 부식은 철근콘크리트의 거동과 구조물의 내구성을 저하시키기 때문에 근본적인 원인인 강재를 대체할 필요가 있다. 최근 건설산업에서 복합재료는 높은 강도, 낮은 중량, 부식에 대한 우 려가 없어 주목받고 있는 재료이다. 복합재료는 섬유와 기지재료로 사용되는 수지에 따라 재료의 특성이 달라지게 되며 이중 탄소섬유 를 활용한 복합재료 CFRP은 복합재료 중 가장 뛰어난 성능을 보여준다. 따라서 본 연구에서는 뛰어난 성능을 보여주는 CFRP와 경제 성을 고려하여 탄소섬유와 유리섬유를 혼합한 CFRP Hybrid를 사용하여 강재의 대체품으로 사용가능성을 확인하고자 한다. 재료의 특 성을 비교하기 위하여 ASTM 규정에 따라 인장시험과 압축시험을 수행하고 반복하중에 대한 저항을 확인하기 위하여 인장반복시험과 압축반복시험을 수행한다. 이때 측정된 응력, 영구변형 등을 그래프로 도식화하고 강재와 비교분석을 진행하였다.

In the present study, a calorimeter was used to experimentally investigate the heating capacity and COP changes according to the pipe length of a variable capacity A/C system with long pipes. Cooling capacity, COP, and compressor discharge temperature were obtained by changing pipe lengths and loading duties at fixed indoor and outdoor temperatures. And the operation status and cycle change process of the A/C system were investigated using some experimental data and P-h diagrams. As the pipe length changes, the heat transfer within the cycle and the operating load of the compressor change, so the heating capacity and COP of the system change. At the same loading duty, as the pipe length increases, the heating capacity and COP decrease. As the loading duty increased, the heating capacity increased almost linearly, but the COP decreased. Since the long pipe experimental value for the compressor discharge temperature has a temperature deviation of up to 1 7℃(50m, L/D : 10/10) from the correlation equation, the optimal correlation equation must be derived through additional research.

In the present study, a calorimeter was used to experimentally investigate the cooling capacity and COP changes according to the pipe length of a variable capacity A/C system with long pipes. Cooling capacity, COP, and compressor discharge temperature were obtained by changing pipe length and loading duty. And the operation status and cycle change process of the A/C system were investigated using some experimental data and P-h diagrams. In long pipes, the pressure drop increases and the operating load on the compressor increases. Additionally, at the same loading duty, cooling capacity and COP decrease and the compressor discharge temperature increases. As loading duty increases, cooling capacity and compressor power consumption increase. Since the temperature deviation between the experimental value and the correlation equation for the discharge temperature of the long-pipe compressor shows a maximum of 10.5℃(50m, L/D : 20/0), the existing correlation equation needs to be modified.

Earthquakes of magnitude 3.0 or greater occur in Korea about 10 times on average yearly, and the number of earthquakes occurring in Korea is increasing. As many earthquakes have recently occurred, interest in the safety of nuclear power plants has increased. Nuclear power plants are equipped with many cabinet-type control facilities to regulate safety facilities, and function maintenance is required during an earthquake. The seismic performance of the cabinet is divided into structural and functional performances. Structural performance can be secured during the design procedure. Functional performance depends on the vibration performance of the component. Therefore, it is necessary to confirm the seismic performance of the components. Generally, seismic performance is confirmed through seismic simulation tests. When checking seismic performance through seismic simulation tests, it is difficult to determine the effect of frequency and maximum acceleration on an element. In this paper, shaking table tests were performed using various frequencies and various maximum accelerations. The seismic performance characteristics of the functions of electrical equipment components were confirmed through tests.