Environmental pollution has led to global warming, which threatens human life. In response, hydrogen is gaining attention as a next-generation energy source that does not emit carbon. Due to its explosive nature, special care must be taken in the safe storage and transportation of hydrogen. Among various storage methods, liquefied storage, which can reduce its volume to 1/800, is considered efficient. However, since its boiling point reaches -253°C, the design of an insulation system is essential. For the design of insulation systems applied to large containers, a membrane-type design is required, which necessitates the use of cryogenic adhesives. To evaluate whether the cryogenic adhesive is properly implemented, assessments such as tensile and shear tests are necessary. This study presents a methodology for shear evaluation. Conventional methods for shear evaluation of adhesives result in slippage, preventing proper assessment. Therefore, a method involving drilling holes in the gripper and pulling from the holes must be applied. Optimal design concerning the size and location of the holes is required, and this study derives optimal values based on finite element analysis. By conducting experiments based on the results of this study, it is expected that the risk of gripper damage will be minimized, allowing for accurate evaluation of the adhesive’s performance.

Liquefied hydrogen is attracting attention as an energy source of the future due to its hydrogen storage rate and low risk. However, the disadvantage is that the unit price is high due to technical difficulties in production, transportation, and storage. This study was conducted to improve the design accuracy and development period of needle valves, which are important parts with a wide technical application range among liquefied hydrogen equipment. Since the needle valve must discharge an appropriate flow rate of the liquefied fluid, it is important to determine the needle valve design parameters suitable for the target flow rate. Computational Fluid Dynamics and Artificial Neural Network technology used to determine the design variables of fluid flow were applied to improve the setting and analysis time of the parameter. In addition, procedures and methods for applying the design parameter of needle valves to Convolutional Neural Networks were presented. The procedure and appropriate conditions for selecting parameters and functional conditions of the Convolutional Neural Network were presented, and the accuracy of predicting the flow coefficient according to the design parameter was secured 95%. It is judged that this method can be applied to other structures and machines.

Liquified hydrogen is considered a new energy resource to replace conventional fossil fuels due to environmental regulations by the IMO. When building tank for the storage and transportation of liquified hydrogen, materials need to withstand temperatures of -253°C, which is even lower than that of LNG (-163°C). Austenitic stainless steel mainly used to build liquified hydrogen tank. When building the tanks, both the base material and welding zone need to have excellent strength in cryogenic condition, however, manual arc welding has several issues due to prolonged exposure of the base material to high temperatures. Laser welding, which has some benefits like short period of exposure time and decrease of thermal affected zone, is used many industries. In this study, laser bead on plate welding was conducted to determine the laser butt welding conditions for STS 304 and STS 316L steels. After the BOP test, cross-section observations were conducted to measure and compare four bead parameters. These tendency result of laser BOP test can be used as conditions laser butt welding of STS 304 and STS 316L steel.

In order to respond to environmental pollution, developed countries, including Korea, have begun to conduct research to utilize hydrogen energy. For mass transfer of hydrogen energy, storage as liquid hydrogen is advantageous, and in this case, the volume can be reduced to 1/800. As such, the transportation technology of liquefied hydrogen for ships is expected to be needed in the near future, but there is no commercialized method yet. This study is a study on the technology to test the performance of the components constituting the membrane type storage container in a cryogenic environment as a preparation for the above. It is a study to find a way to respond by analyzing in advance the problems that may occur during the shear test of adhesives. Through this study, the limitations of ISO4587 were analyzed, and in order to cope with this, the specimen was supplemented so that fracture occurred in the adhesive, not the adhesive gripper, by using stainless steel, a low-temperature steel, to reinforce the thickness. Based on this, shear evaluation was performed under conditions lowered to minus 243℃, and it was confirmed that the breaking strength was higher at cryogenic temperatures.

금속의 취성화는 수소와 접촉하는 구조물을 안정적으로 설계하는데 있어서 큰 문제가 되어왔다. 본 논문에서는 분자동역학 해석을 통해 균열선단 주변에 모인 수소원자들이 전위 이동 현상을 억제하고, 이로 인해 벽개 파괴 현상이 발생하는 것을 확인하였다. 다양한 수소 농도, 하중 속도, 수소 확산 속도 등을 바꾸어가며 분자동역학 해석을 수행하였고, 이에 따른 수소 취성화를 최소화시킬 수 있는 조건들을 조사하였다. 분자동역학 해석 결과는 기존의 실험결과와 잘 일치하였으며 이를 바탕으로 수소 취성화 현상을 정량화하여 평가하였다.

강화되는 환경규제에 대응하기 위해서 세계 각국이 수소 경제로의 전환을 본격화하고 있으며, 이에 중장기적으로 수소의 국가 간 물동량도 증가할 것으로 예상된다. 국가간 수소의 거래는 수출국의 신재생 에너지 자원과 수입국의 수소 사용 형태, 기술 성숙도 등을 고려하여 암모니아, 액화수소, LOHC 등의 형태로 이루어질 것이나, 어느 한 가지 형태로만 거래되지는 않을 것이다. 액화수소 대비 암모 니아와 LOHC의 해상운송은 상대적으로 성숙한 기술임에 본 글에서는 향후 액화수소 운반선 개발을 위하여 필요한 세부 기술들의 식별 및 다양한 기술적 대안들을 통해 가능한 설계안을 확보하면서, 그에 따른 기술적 타당성을 분석하였다.

Conversion to modern hydrogen energy is required, and research on liquefied hydrogen cargo containment systems is needed for large-capacity transport and storage. In this study, changes in the mechanical properties of the adhesive required for storage and transport in liquid hydrogen were confirmed. The lap shear test was performed by realizing cryogenic conditions in a small chamber using liquid nitrogen and liquid helium. There was an increase of 11.0% in the -180℃ condition compared to room temperature, and an increase of 1.8% in the -230℃ condition compared to the -180℃ condition was confirmed. In the case of shear strain, it is known that it decreases as the temperature goes down. As a result of the experiment, it was confirmed that the value at room temperature and the value at -180℃ reduced the shear strain by 5.0%, and -230˚ compared to the -180℃ condition. An increase of 1.5% was confirmed in the C condition. In the case of the specimen tested at -230℃, the deformation in the gripper part was larger than in other tests, and it is judged that the maximum shear strength and shear strain were affected. In addition, in this study, there is a limitation in the experiment at -230°C rather than 253°C, which is the boiling point of hydrogen

In modern times, where problems due to environmental pollution are continuously occurring, hydrogen is in the spotlight as the energy of the future. Hydrogen is an eco-friendly energy resource that does not even generate CO2, and is actively supporting research to utilize hydrogen energy at the national level. This study is a study on the cryogenic mechanical properties of the elements constituting the cargo hold during the transportation of liquid hydrogen. Among the various components, the evaluation of mechanical properties of the cryogenic adhesive under liquid helium conditions was confirmed. The related contents are summarized as follows. As a result of performing SSRT by curing the adhesive, it was confirmed that tensile strength and maximum strain were increased at cryogenic temperature (-230°C) compared to room temperature (25°C). It was confirmed that the adhesive-hardened specimen showed a brittle fracture mode at both room temperature and cryogenic temperature during tensile. Improvements in this study, such as pores occurring during adhesive curing, the use of standard specimens, and experiments at -253°C, the boiling point of hydrogen, exist, and are planned to be carried out in subsequent studies.

최근 환경 문제를 포함하여 여러 이유로 액화가스에 대한 수요가 증가하고 있다. 이로 인하여 선박을 통한 액화가스의 운송이 증대하고 있고, 이를 수용할 터미널 건설도 다수 이루어지고 있다. 터미널을 건설하는데 있어 그 규모의 결정은 대상선박이 명확히 결정 되어 있을 경우 그에 따른다. 그렇지 않다면 터미널이 수용하고자 하는 선박 규모를 결정하고, 관련한 규정이나 기준에 제시되어 있는 선박 치수를 활용한다. 이와 관련하여 최근 액화가스터미널 건설을 위해 항만 건설시 설계기준으로 가장 많이 적용하는 항만 및 어항 설계 기준 및 해설(2017)을 활용하여 대상선박의 규모를 파악하는 과정에서 대형화된 선박의 기준이 마련되어 있지 않고, 제시되어 있는 선박의 주요치수가 실질적으로 운항하고 있는 선박과 상당히 상이하다는 점이 발견되었다. 이러한 문제점으로 인하여 터미널을 건설하는데 있어 대상선박 및 터미널의 규모 결정, 터미널의 안전성 평가 등에 있어 이해 당사자 간의 많은 이견이 있을 수 있기에 현행 액화가스운반선의 주요치수에 대한 기준을 현재 운항하고 있는 선박들의 현황 분석을 통하여 개정안을 제시하였다. 제시된 개정안은 향후 선박 및 터미널 규모 결정에 보다 적절하고 현실적인 기준으로 활용되고, 불필요한 터미널 건설비용 증가를 막을 수 있을 것으로 기대된다.

Mass mortality of mariculture fish due to high summer temperatures is a major issue in the mariculture industry in many coastal waters of Korea, yet measures to mitigate the impact are generally limited. We injected a micro-bubble of liquefied oxygen into the bottom of rockfish cages (about 6-8 m deep) in order to maximize the dispersal of micro-bubbled seawater and reduce fish mortality. The injection of low-temperature oxygen in micro-bubbles lowered the water temperature at the injection area by as much as 1℃ and increased dissolved oxygen concentration by 0.5 ppm. In early August, following a week with persistent high water temperature (above 28.5℃), there was an increase in fish mortality despite the micro-bubble system, which resulted in approximately 7% death of the total introduced fish population. However, this mortality appeared to be much lower than mortality reported in a neighboring mariculture facility (approximately 50% mortality). We also estimated the volume that can be recirculated with pumped seawater using a micro-bubble system. We suggest that this approach of injecting liquefied oxygen through a micro-bubble system may reduce fish mortality during high temperature periods.

액화석유가스(Liquefied Petroleum Gas)를 연료(Fuel)로 하는 차량의 실제 운행단계에서 시동 꺼짐 현상 등이 발생한다는 소비자 민원이 접수 된 바 있으며, 최근 유통과정에서 녹 등의 이물질로 인한 소비자 피해 가능성이 제기되어 LPG 잔류물질(Residue) 항목에 대한 관리 필요성이 대두되었다. 본 연구에서는 LPG 국내생산 및 수입사 제품과 실제로 유통되고 있는 LPG의 잔류물질 특성을 연구하였다. LPG 잔류물질을 GC-MS를 사용하여 정성분석을 하였고, ICP-OES를 이용하여 무기물 성분을 분석하였다. GC-MS 분석결과 고무 제조공정을 용이하게 하기 위해 고무에 소량 배합하는 가소제(Plasticizer) 등이 분석되었다. 또한 ICP-OES를 이용한 무기물 분석결과 주로 LPG 생산 시 사용되는 소포제 등에서 유래된 것으로 추정되는 Si와 충전시설 등에 사용되는 그리스 첨가제 성분 등으로 추정되는 P와 Zn도 일부 검출되었다. 본 연구에서 분석된 LPG 잔류물질에 대해서는 녹 등을 유발할 수 있는 성분이 검출되지 않았지만 가소제 및 그리스 첨가제 성분이 LPG 연료계통에 영향을 줄 수 있으므로 적정품질의 고무류 사용과 저비점 그리스 첨가제 사용 확대가 필요할 것으로 보인다.

As the chemical industry becomes more advanced, the awareness of chemical accidents is rising, and legal systems for chemical safety management are strengthened. In this study, quantitative risk assessment of liquid chlorine leak was conducted. Risk assessment was performed in the order of frequency analysis, consequence analysis, and risk calculation. The individual risk was presented in the form of contour lines. The social risk was expressed by the FN curve. The risk of day and night was in an unacceptable area, so it was required to mitigate risk. Therefore in-building, which could trap the pool, was selected as a risk mitigation measure. As a result of the cost benefit analysis, it was concluded that this measure should be reasonably implemented.

본 연구는 폴리프로필렌(PP) 수지의 Co 및 Mo 촉매에 의한 반응시간과 농도변화에 따른 저온열분해 액화특성을 파악하고자 회분식 반응기를 이용하여 특정 온도(425, 450, 475℃)에서의 전환율을 측정하였다. 열분해 시간은 20~80분으로 설정하였고 생성물은 산업통상자원부에서 고시한 증류성상 온도에 따라 가스, 가솔린, 등유, 경유, 중유로 분류하였다. 그리고 450℃ 반응온도에서 촉매 사용에 따른 전환율은 모든 반응시간에 있어 Mo 촉매 > Co 촉매 > 무촉매 순이었다. Co 및 Mo 촉매 농도별 PP 전환율 및 열분해 생성물 수율은 Co:Mo=50:50 혼합시 가장 우수한 것으로 나타났다.

피셔-트롭쉬 합성 반응은 촉매 표면에서 합성가스 (CO+H₂)를 탄화수소로 전환하는 반응이다. 코발트 또는 철계 촉매는 친환경적인 디젤 연료를 생산할 수 있고 합성가스의 전환율이 높은 촉매로 알려져 있다. 피셔-트롭쉬 반응에 사용되는 촉매의 활성은 촉매 표면에서의 활성점에 의존적이다. 활성점은 활성 물질의 크기, 담지량, 환원율, 지지체와 활성물질의 상호작용에 의해 결정된다. FT 촉매 제조 방법으로 활성물질의 크기를 조절하는 등의 새로운 방법들이 시도되고 있다. 여기에서는 촉매의 제조 방법과 환원 특성을 비롯한 촉매의 형태와 반응 조건을 포함한 반응기 형태에 대해 알아보겠다.

몽골은 석탄 매장량이 매우 풍부하고 석유연료를 전적으로 수입에 의존하기 때문에, 석탄액화플랜트 건설에 필요한 충분한 여건을 갖추고 있다. 본 연구에서는 몽골에 하루 10,000배럴의 석유연료를 생산할 수 있는 석탄액화플랜트를 건설할 경우에 대한 경제성분석을 수행한다. 먼저 기존에 있는 산업계의 석탄액화플랜트 프로젝트 데이터와 학계의 연구결과를 토대로 몽골 석탄액화플랜트 건설에 필요한 비용과 기대수명, 그리고 예상 수명기간 동안 운영했을 때 발생하는 운영