택코트란 아스팔트 포장 공사 시 기존 아스팔트층과 신설 아스팔트 층 사이에 부착성을 증가시키기 위하여 사용되는 재료이다. 교통 하중으로 인해 포장 경계면에서 수평전단응력 및 수직인장응력이 발생하게 되는데 택코트의 유실, 양생 부족 등의 문제로 접착 성능 이 부족하면 포장층의 분리, 밀림과 같은 도로 파괴가 형상이 나타날 수 있다. 현재 국내에서는 국토교통부 아스팔트 콘크리트 포장 시공 지침에 택코트 살포량에 대한 기준은 존재하지만 기존 및 신설 아스팔트 포장층 사이에 택코트의 접착강도에 대한 기준은 존재 하지 않는 실정이다, 이는 접착강도 특성이 분석되지 않은 택코트를 사용함에 따라 아스팔트 포장의 공용성 측면에서 문제를 초래할 수 있다. 따라서 본 연구에서는 PG등급이 다른 택코트 4종류에 대한 인장 및 전단접착강도를 확인하기 위하여 인장접착강도 시험, 전 단접착강도 시험을 진행하였다. 택코트의 양생정도에 따른 접착강도 특성을 확인해보기 위하여 택코트의 수분이 증발됨에 따라 중량 변화가 없는 상태를 양생 100%로 하여 양생 0%, 50%, 100%로 진행하였으며, 살포량은 국토교통부 아스팔트 콘크리트 시공 지침에 따 라 0.5ℓ/m2로 진행하였다. 사용된 택코트 종류에 관계 없이 양생 정도가 증가함에 따라 접착강도는 증가하는 추세를 보였으며, 인장 및 전단접착강도 시험에 관계없이 초기 양생(양생 0%~50%)보다 양생 50% 이후에서의 더 높게 강도가 발현된 것을 확인하였다. 또한 PG등급이 높은 택코트가 인장 및 전단접착강도에 관계없이 접착강도 성능이 우수한 것을 확인할 수 있었다. 추후 택코트의 종류를 추 가하여 PG등급이 분류가 이루어진 후에 접착강도 시험을 진행하여 결과를 확인할 예정이다.

In order to respond to environmental pollution, developed countries, including Korea, have begun to conduct research to utilize hydrogen energy. For mass transfer of hydrogen energy, storage as liquid hydrogen is advantageous, and in this case, the volume can be reduced to 1/800. As such, the transportation technology of liquefied hydrogen for ships is expected to be needed in the near future, but there is no commercialized method yet. This study is a study on the technology to test the performance of the components constituting the membrane type storage container in a cryogenic environment as a preparation for the above. It is a study to find a way to respond by analyzing in advance the problems that may occur during the shear test of adhesives. Through this study, the limitations of ISO4587 were analyzed, and in order to cope with this, the specimen was supplemented so that fracture occurred in the adhesive, not the adhesive gripper, by using stainless steel, a low-temperature steel, to reinforce the thickness. Based on this, shear evaluation was performed under conditions lowered to minus 243℃, and it was confirmed that the breaking strength was higher at cryogenic temperatures.

This paper aims at investigating the adhesive property at damage analysis according to the shape of the DCB test specimen made of Titanium, Dualumin as the high strength nonferrous metals. In this analysis, all three specimens had the lower holes bound by the cylinder support and the top holes were elongated with the rate of 6mm/min. The study results show that the longer the load block of DCB specimens, the more reliable and durable they are. It is utilized as the basic data at investigating the damage properties of adhesives in DCB specimens made of high strength nonferrous metals.

In this paper, the experimental study and finite elements analysis were conducted on homogeneous and dissimilar metals single lap-shear bonded joints to investigate the factor that affect the joint failure load. It was found that factors which have the significant effects on the failure load of the joint was stiffness of the adherends. And from experimental results, it can be confirmed that the failure load increases linearly with overlap length increases. And the failure load of dissimilar metal joints is approximately 1KN(10 ～17%) larger than homogeneous metal joints. In order to confirm this phenomenon, the stress distribution and strain distribution of the specimens were analyzed through the finite element analysis. The difference between homogeneous metals joints and dissimilar metals joints is that stress and strain in adhesive are concentrated at the end of the overlap zone close to aluminium which has lower rigidity than aluminium in case of dissimilar metals joints. From high rigidity of steel, the stress concentration in bonds are decreased and it cause increase of the failure strength at dissimilar metal joints.

PURPOSES: The performance of tack coat, commonly used for layer interface bonding, is affected by application rate and curing time. In this study, bonding strength tests were performed according to the application rate and curing time of asphalt emulsion. Based on finding from this study, optimum application rates and curing times are proposed. METHODS: In order to investigate bonding characteristic of asphalt emulsion, tests were performed on both asphalt concrete pavement and portland concrete pavement. Also, asphalt emulsions were tested at the application rate of 0, 0.2, 0.4, 0.6, and 0.8l/m2 and at the curing time of 0, 0.5, 1, 2, and 24 hours. Pull-off test and shear bonding strength test, which commonly used for bonding strength measurement of asphalt emulsion, were adopted for this study. To assess field performance under different testing condition, asphalt emulsions were applied to in-service pavement. Throughout coefficient of determination analysis between material index properties from asphalt emulsion and mechanical response from bonding strength tests, performance correlativity was analyzed. RESULTS: Test results show that optimum application rate for asphalt overlay on asphalt concrete pavement (AOA) and asphalt overlay on concrete pavement (AOC) was 0.4~0.5l/m2 and 0.3~0.5l/m2, respectively. According to the curing time increment, tensile strength and shear strength of AOC were increased to 22~44% and 20~39%, respectively. AOA case also show strength increment in tensile strength (42%) and shear strength (9%). We tested the applicability of tack coat materials at the field sites, and our findings demonstrated that the bonding (for D and E) and rapid curing (for B, C, and D, E) performances were superior than others. Among material index properties, there was a high correlation between penetration ratio and bonding strength test result. CONCLUSIONS : Result show that interlayer bonding strength was affected by asphalt emulsion type, application rate and curing time. AOC required slightly higher application (0.1l/m2) than AOA. Both AOA and AOC cases show higher strength at longer curing time. Up to 2hours of curing, rapid strength increments were observed, but strength increment ratio was decreased after 2hours of curing. From the observed correlation between penetration ratio and bonding strength, it is expected that penetration ratio can be used as one of important factors affecting bonding strength analysis.

PURPOSES : Bonded concrete overlay is a favorable maintenance method since the material properties are similar to existing concrete pavements. In addition, bonded concrete overlay has advantage of structural performance since the overlay layer and the existing pavement perform as a monolithic layer. It is important to have suitable bond strength criteria to secure the performance of bonded concrete overlay. This study aimed to investigate the factors influencing bond strength characteristics between existing concrete pavement and overlay material. METHODS: Bond strength between overlay and existing pavement are measured and analyzed for various conditions such as the type of overlay materials, compressive and flexure strength of overlay and existing pavement, and deterioration status of existing pavement. RESULTS: The strength of overlay material does not significantly influence the bond strength. The overlay of ultra-rapid hardening cement generally gives low bond strength. However, ultra rapid hardening polymer modified concrete gives robust bond strength. The deterioration of existing concrete significantly decrease the bond strength. CONCLUSIONS: Bond strength of bonded concrete overlay highly depends on condition of existing concrete pavement rather than overlay material.

알루미늄 폼을 볼트나 너트를 이용하여 체결한다면 경량성이 감소되므로 접착제로 접합하는 것이 가 장 효율적이다. 이런 알루미늄 폼 접착 구조물에 대한 충격 피로 특성과 접착 합면에 대한 파괴인성 연 구는 매우 부족하며 또한 중요하다. 이에 따라 본 연구에서는 알루미늄 폼으로 만들어진 DCB모델을 접 착제로 접합한 후 두께를 변수로 하여 25mm 부터 45mm까지 10mm차이를 두어 실험과 컴퓨터 시뮬레 이션을 통하여 수행하였다. 실험은 MTS사의 인장 시험기를 사용하여 강제 변위 100mm를 주어 변위에 따른 전단력을 알아보았고, 실험과 똑같은 조건하에 ANSYS를 이용하여 유한요소해석을 수행하였다. 실험과 유한요소해석 값을 비교하여 접착제로 접합된 알루미늄 폼 구조물의 접착 합면에 대한 파괴인성을 고찰하였다.

Aluminum foam has many superb properties such as light weight, impact absorption and thermal resistance by comparing with original metallic materials. Composite materials made of aluminum foam have used at various fields as automotive bumper, shock absorption, vessel and aircraft. But it is inefficient to join aluminum foam with bolt and nut because of the property of light weight. In this study, this approach is investigated by joining aluminum foam with adhesive. Impact fatigue and failure toughness at the commissure of adhesive structure are studied by simulation analysis. This study aims to investigate the shear strength evaluation at shear mode of adhesively bonded joint with double cantilever beam(DCB) made of aluminum foam.

This paper has fabricated insulation gang-form adhering general gang-form to the polyisocyanurate board and analyzed type of members, temperature record by locations and strength development after placing the concrete, in order to ensure efficient concrete quality under cold weather. According to our test, we can see that general gang-form member with curing under the same conditions as the actual field has a trend of constantly decreasing concrete temperature regardless to surface or central area due to rapid outdoor air temperature reduction, while in the case of insulation gang-from I and II, temperature increased up to around 25℃ after 12 hours under rapid outdoor air temperature change and temperature distribution did not appear large separation according to hydration reaction measurement locations. In addition, results of measurement for temperature records on weak insulation area by types of gang-forms showed that the temperature record distribution on the form tie surface and horizontal bar surface of angle bar has generally similar trend as the temperature records on the surface of the insulation gang-form, while corner area of the insulation gang-form did not have large insulation effect. It is determined that it requires additional curing measure for the weak corner area of the insulation gang-form in the future.

본 연구에서는 강재가 맞대기 이음으로 연결될 경우 CFRP(Carbon Fiber Reinforced Plastic) 쉬트(sheet)를 맞대기 이 음부에 접착할 경우 강재 및 CFRP 쉬트에 발생하는 응력을 해석하였다. CFRP 쉬트로 보강한 경우 접착제의 두께, 강재와의 접착 길이, CFRP 강도 변화를 매개변수로 사용하여 이 매개변수에 변화에 따른 이음부의 응력분포를 분 석하였다. 또한 CFRP를 여러 층으로 접착할 경우 각 층의 강도를 다르게 변화시켜 맞대기 이음부에 유리한 응력분 포를 나타내는 CFRP의 강도를 제시하였다. 본 연구를 위해 빠른 수렴성을 가지며 왜곡된 요소형상에서도 정확한 응력결과를 보이는 강화변형률장(Enhanced Assumed Strain Field)을 사용한 평면변형률 유한요소에 대한 프로그램을 작성하였다.

This paper presents the stress distribution of the damaged butt joint of steel plate using CFRP laminates when the flange in tension zone of steel box girder is welded by butt welding. When CFRP sheets are patched on tension flange of steel-box girder, the stress distribution of a vertical and normal direction on damaged welding part is shown as parameters such as a variation of the thickness of adhesive, the overlap length with steel, and the modulus of elasticity of CFRP sheets. For the study, we wrote the computer program using the EAS(Enhanced assumed strain) finite element method for plane strain that has a very fast convergency and exact stress for distorted shape.

The crack initiation equals to fracture for bonded joint with brittle adhesive. The criterion is formulated in terms of the quasi-stress intensity factor Kp, for the maximum principle stress, that is analogous to the stress intensity factor used to characterize the stress field in the vicinity of bond terminus. Kp is evaluated using a boundary element analysis. The crack initiation at the terminus of adhesive bonded joints is estimated with the critical quasi-stress intensity factor Kp. This method presented here hardly pays attention to the crack propagation. Since there is a large influence of crack propagation on the strength of adhesive joints and structures, crack propagation must be taken into account on strength prediction of bonded joints. The quasi-stress intensity factor Kp for the maximum principle stress can use as the criteria of the crack initiation at the terminus of adhesive bonded joints having various shapes.

The objectives of the present study are to show how to predict the crack initiation at the terminus of adhesive bonded joints to calculate the crack growth in the adhesive layer using the total strain energy release rate. The crack propagation for ductile adhesives is theoretically estimated using -curve. -curve is determined from static shearing tests of single lap joints. The total strain energy release rate for single lap joints is evaluated using a boundary element analysis. The strength prediction is conducted by means of the R-curve and the total strain energy release rate.The conclusions are summarized as follows; (1) A crack propagation geometry of the bonded structure using ductile adhesive was predicted from the distribution of the total strain energy release rate. (2) The final failure load for lap joints is predicted by the R-curve method based on the fracture mechanics. (3) The final failure load for stiffened plates with a steel L-beam is predicted by the R-curve method based on the fracture mechanics.

방수시스템(WPS)의 성능은 재료 인자들의 복잡한 상호작용, 설계상세, 그리고 시공의 질에 따라 영향을 받고, 주로 인장접착강도(TAS)로 측정되는 교면과의 접착성에 의해 결정되는 것으로 알려져 있다. 따라서 본 연구는 현재 국내에 유통되고 있는 교면방수재 8종의 WPS의 성능을 아스팔트 포장층 혼합물의 종류, 시공시 혼합물의 온도, 포장층의 두께, 반복주행시험에 따른 접착특성을 중심으로 인장접착특성을 비교하였다. 또한 TAS 시험 후 계면에서의 탈리상태를 조사하였다. WPS에 대한 TAS 시험결과 SMA 혼합물이 밀입도 혼합물 보다 TAS가 크게 나타나 아스팔트 혼합물 종류에 따라서 차이가 났다. 시트식 방수재는 아스팔트 혼합물의 종류에 상관없이 시공온도가 높은 것이 접착력이 더 크게 나타났으나 도막식에서는 방수재 계열별로 다소 차이가 있고 시트식과 같지 않은 것으로 나타났다. 포장층 두께에 따른 영향은 방수재 종류에 상관없이 대동소이한 것으로 나타났다. 반복주행시험에 따라서 시트식에서의 접착력은 하중 재하지점>하중재하 않은 곳>하중 재하지점 옆 부근의 순서로 나타났고, 도막식에서는 방수재 종류에 따라 다르게 나타났다. 또한 방수재의 종류 및 특성에 따라 방수시스템 계면에서의 탈리상태가 다르다는 것을 알 수 있었다.

방수시스템(WPS)의 성능은 재료 인자들의 복잡한 상호작용, 설계상세, 그리고 시공의 질에 따라 영향을 받고, 주로 인장접착강도(TAS)로 측정되는 교면과의 접착성에 의해 결정되는 것으로 알려져 있다. 따라서 본 연구는 현재 국내에 유통되고 있는 교면방수재 8종의 WPS의 성능을 아스팔트 포장층 혼합물의 종류, 시공시 혼합물의 온도, 포장층의 두께, 반복주행시험에 따른 접착특성을 중심으로 인장접착특성을 비교하였다. 또한 TAS 시험 후 계면에서의 탈리상태를 조사하였다. WPS에 대한 TAS 시험결과 SMA 혼합물이 밀입도 혼합물 보다 TAS가 크게 나타나 아스팔트 혼합물 종류에 따라서 차이가 났다. 시트식 방수재는 아스팔트 혼합물의 종류에 상관없이 시공온도가 높은 것이 접착력이 더 크게 나타났으나 도막식에서는 방수재 계열별로 다소 차이가 있고 시트식과 같지 않은 것으로 나타났다. 포장층 두께에 따른 영향은 방수재 종류에 상관없이 대동소이한 것으로 나타났다. 반복주행시험에 따라서 시트식에서의 접착력은 하중 재하지점>하중재하 않은 곳>하중 재하지점 옆 부근의 순서로 나타났고, 도막식에서는 방수재 종류에 따라 다르게 나타났다. 또한 방수재의 종류 및 특성에 따라 방수시스템 계면에서의 탈리상태가 다르다는 것을 알 수 있었다.

HIP처리가 가스터빈 고정익 등 고온부품에 적용되는 열차폐 코팅층의 접착강도 및 고온특성에 미치는 영향을 조사하였다. 시편은 IN738LC 초합금 표면에 8wt%Y2O3-ZrO2분말을 플라즈마 용사법으로 코팅한 후 1200˚C, 100MPa의 고온, 고압에서 4시간 동안 HIP 처리하여 준비하였다. 실험결과 HIP 처리된 코팅의 경우 미세균열과 기공이 상당량 감소하였으며 EDX분석을 통해 계면에서 원자간 상호확산이 발생한 것을 확인하였다. 이러한 코팅층의 치밀화 및 상호확산으로 인해 HIP처리된 코팅층의 접착강도는 48% 이상 크게 증가하였으며 조직 또한 균질화 되었다. 반면 가열과 냉각이 반복되는 환경에서 코팅층의 내구력은 HIP 처리된 경우가 다소 저하되었다. 이는 코팅과 모재와의 열팽창 차이로 인한 변형을 완화시켜주는 기공과 미세균열이 감소되었기 때문으로 판단된다.

The purposes of this study is to evaluate the adhesion in flexure and adhesion in tension between old-plain cement mortar and new-polymer cement mortar that has been widely used as finishing and repairing materials of RC structures. From the test results, the adhesion in flexure and adhesion in tension of polymer-modified mortar to plain cement mortar are much higher than that of plain cement mortar, and are increased with increasing polymer-cement ratio. The maximum strengths show at polymer cement mortar using EVA dispersion, and those are about 1.69 and 2.10 times respectively, plain cement mortar.

As the pilot study on textile reinforced mortar(TRM) construction method, the present research has been conducted to investigate the tensile performance of fiber-reinforced polymer(FRP) grids inserted in inorganic mortar. For this purpose, experiment was carried out using twenty specimens with the main parameters of inorganic mortar and FRP grids. As a result, splitting failure did not occur between inorganic martar and FRP grids. As FRP grids were completely fractured, the specimens failed by showing the similar tensile behavior to the mechanical properties of FRP grids.