The premature failure of the universal joint connecting the drive gear box and the cooling fan caused a deterioration in serviceability and operability. Universal joint is a device that transmits engine power to a cooling fan. Internal pin breakage and shaft separation can cause secondary damage such as cooling fan malfunction and radiator damage caused by component failure. The purpose of this paper is to analyze the damage phenomenon of universal joints caused by bundles in SPVs and to improve them. In order to verify the improvement, a single part test and a system conformance test were conducted, and durability test was conducted to confirm the improvement effect on the improved prototype. Through these, the effects of increasing the durability of the improved product were estimated.

This study is to investigate the improvement of quality and cost reduction of welding materials for combat vehicles through localization. The existing imported welding wires and localized welding wires were evaluated. The evaluation of the welding wires was performed for the feedability, chemical/mechanical properties, macro testing, and weldability. As a result of evaluation, the localized welding material met all the evaluation standard values. In addition, it showed excellent performance in terms of weldability and feedability. It is judged that the welding quality is improved thanks to the improvement of feeding characteristics through the localization of the welding material, and the fatigue of the worker is also expected to be relieved.

The performance characteristics of a lead acid battery are investigated with the content of Sodium Perborate Tetrahydrate (SPT, NaBO3·4H2O) in a positive plate active material. SPT, which reacts with water to form hydrogen peroxide, is applied as an additive in the positive plate active material to increase adhesion between the substrate (positive plate) and the active material; this phenomenon is caused by a chemical reaction on the surface of substrate. A positive plate with the increasing content of SPT is prepared to compare its properties. It is confirmed that the oxide layer increases at the interface between the substrate and the active material with increasing content of SPT; this is proven to be an oxide layer through EDS analysis. Battery performance is confirmed: when SPT content is 2.0 wt%, the charging acceptance and high rate discharge properties are improved. In addition, the lifetime performance according to the Standard of Battery Association of Japan (SBA) S0101 test is improved with increasing content of SPT.

본 논문은 버스정류장 미세먼지 저감을 위해 설계된 도로시설물의 성능평가 과정 및 결과를 보고한다. 먼저, 유한요 소해석 프로그램인 LS-DYNA를 이용하여 대상 구조물에 대한 충돌해석이 수행되었다. 해석변수로 차량의 속도와 충돌 위치를 고려한 다양한 조건에서의 구조해석이 진행되었다. 대상 시설물의 성능은 이 결과를 이용하여 구조적 성능과 충돌 후 차량의 안전성능이 평가되었다. 해석결과로부터 충돌속도가 증가하고 충돌위치가 전면으로 갈수록 시설물의 구조성능과 차량의 충돌 후 안전성능이 저하되는 것이 콘크리트의 손상량을 통해 확인되었다. 더불어 충돌 후 차량의 거동에 대한 분석을 통해 시설물에 연속되는 연석이 설치되면 차량의 이탈을 방지해 안전성능을 확보하는 것으로 예측되었다. 최종적으로, 대상 시설물은 설계 시 고려된 목표 충돌속도 25km/h보다 더 큰 40km/h까지 충분한 안전성능을 확보하고 있다는 것이 확인되었다.

This study is to investigate the cause of the malfunction of the ground tracked combat vehicle rotating roller and set future direction of improvement. The integrity of the initially used plate and rotating roller was evaluated. As evaluation methods, mechanical property test, radiographic test and size checking test were performed. PA66, PA12, PET, and POM were selected among polymer materials and tested for water absorption rates. Through mechanical property test and radiographic test, the materials used initially were identified to be sound. In the evaluation of the selected four polymer materials, it was confirmed that the PET was excellent in the mechanical properties and the water absorption rate. PET is excellent in mechanical properties and water absorption.

Unlike wheeled vehicles, tracked armored vehicles require a highly developed transmission technology since the transmission has to not only shift gears but also steer and brake the heavy ground weapon system precisely. Even though weapons systems including the K00 Infantry Fighting Vehicle (IFV) have recently been developed with domestic technology, it is true that many core parts in the systems are still being imported. In this paper localization process of the accumulator which is one of the most important hydraulic parts in the K00 transmission is introduced. In order to determine design variables such as operating pressure we analyzed torque characteristics of the transmission and calculated spring constant by disassembling the original accumulator. And tests such as durability, safety, etc. were conducted to assure the validation of the development. We expect that the process of reverse engineering we adopted will be helpful to localize similar hydraulic parts.

Vortex tube is a simple structure and environmentally friendly method of temperature separation. In this paper, the applicability of the vehicle air conditioning system using the Vortex tube was reviewed. Experimental conditions, the pressure was set at 0.5~5.0kgf/cm2, and the cold air flow ratio (yc) was set at 0.1~0.9. Experiment result, the high temperature section represents the highest temperature value at yc=0.8. The cold zone represents the lowest temperature value at yc=0.5. In case of indirect heat exchanger experiment result, the maximum temperature difference was 11°C in the cold zone and 15°C in the hot zone. In case of direct heat exchange, the low temperature area was 11°C and the high temperature area was 11°C. According to the experiment result, although indirect heat exchange method performs better than direct heat exchange method, the time to reach normal temperature is four times slower than direct heat exchange method. Therefore, in order to apply to a vehicle air conditioning system, it is judged that it is effective to use a direct heat exchange method having a fast reaction speed and a low flow rate resistance.

Considering the features of body repair for automotive body where same damage and repair conditions does not exist in car accident, it is essential to acquire know-how and continuously approach new materials and new technologies on the site of maintenance where the theoretical instruction of textbook cannot react accurately minute by minute. Especially, in case of car repair from unexpected accidents such as body repair or dent repair, it is difficult to satisfy vehicle owners despite their request. Accordingly, this study researched the better maintenance technology to restore to its original state with more improved technology as vehicle owners wish. This study made time to repair reduced by 98% and the cost reduced by 79.6% through the accurate diagnostic technique before repair and maintenance technologies of body crash analysis applying property of high-speed tensile. It also obtains intangible effects including prevention of environmental pollution and maximization of vehicle owners satisfaction.

The purpose of this study is to provision the standard method for ensuring the reliability of measuring indoor air quality in public transportation. The objective is to determine the difference in the measured concentration values according to various conditions. These variables include measurement conditions, measurement equipment, measurement points, and measurement time. The value differences are determined by measuring the PM10 and CO2 concentration of subways, and express buses and trains, which are targets of indoor air quality management. The concentration of CO2 was measured by the NDIR method and that of PM10 was measured by the gravimetric method and light-scattering method. Statistically, the results of the concentration comparison according to the measurement points of the public transportation modes were not significantly different (p > 0.05), and it is deemed that the concentration is not affected by the measurement points. In terms of the concentration analysis results according to the measurement method, there was a difference of the concentration between the gravimetric and light scattering method. In the case of the light scattering method, the concentration differed depending on whether it was corrected with standard particles in the laboratory environment.

The purpose of this study is to propose future-oriented high-rise buildings where the vehicle is parked at the top of the building. At the same time, the vehicle is used as a part of the building along with the advent of the era of autonomous driving. The suspended structure is proposed as a suitable structural system for architectural planning. This system is free to design because there are no limitations on column planning compared to conventional designs. In particular, the low-floor plan can be used as an open space because colums are not arranged in the lower-floors. Thereby opened low-floor plan has advantages that visual perception of the space is improved, noise problems along the side of the street is solved and planning underground parking spaces are easier. These advantages can solve the problem of overlapping columns with vehicle traffic in the building. However, there are some problems that the suspension structure is mainly a formal form and the usable area is small compared to the core area because it is a core-oriented structural system. In this regard, a new structural system was proposed by combining the concept of suspended structure and cable stayed column. Therefore, this paper analyzes the existing style of high-rise housing suspended Structure and proposes a new structural system and the concept of design for autonomous vehicles.

차량 및 화물 고박불량과 횡경사에 따른 화물의 이동으로 인한 여객선 침몰사고 이후 화물 고박의 중요성이 제기되었고 카페리선박의 구조 및 설비 등에 관한 기준이 개정되어 풍속 7 m/sec, 파고 1.5미터를 초과하는 해상상태에서는 평수구역을 운항하는 카페리여객선에 적재된 모든 차량은 고박을 실시해야 한다. 본 연구에서는 평수구역을 운항하는 여객선의 해상상태에 따른 선체운동을 계측하고 NSM(New Strip Method) 계산 결과와 비교 하였으며, 대상선박은 풍속 6 ~ 8 m/s, 파고 0.5 ~ 1.0미터의 해상상태에서 최대 1.41° 및 1.37°의 종 동요와 횡 동요를 하였고, 풍속 10 ~ 12 m/s, 파고 1.0 ~ 1.5미터의 해상상태에는 최대 1.49° 및 2.43°의 종 동요와 횡 동요를 하였다. 선체운동 결과를 반영하여 외력과 지지력을 비교해 본 결과 고박하지 않은 상태의 지지력이 더 강한 것으로 평가되어 해당 기상조건에서는 고박을 하지 않아도 차량이 미끄러지거나 전도되지 않는 것으로 평가되었다. 향후 다양한 선박의 선체운동 측정, 외력 및 지지력 비교를 통해 보 다 합리적인 차량고박 기준 개정이 요구된다.