This paper presents the torque ripple reduction control to apply an SRM to the X-by-wire drive systems which replaces the mechanical control method with “by-wire” to secure the flexibility of design and modification. However, torque ripples generated from the SRM can affect the performance and stability of the system. The proposed torque ripple control schemes are compared with the previously studied methods by dynamic simulation in regards to torque distribution functions and instant torque controller.

In this paper, 1kW prototype PCS for tidal power generation system, which is attracting attention as the next-generation renewable energy, is studied. Tidal power generation is a method of producing energy using the difference between the tides. The advantage of tidal generators is that, unlike other renewable energies such as wave power, wind power, and solar power, they are relatively less affected by the weather changes and are regularly produced at regular intervals.

Due to stricter environmental regulations of the International Maritime Organization (IMO), the number of ships fueled by Liquefied Natural Gas (LNG) is rapidly increasing. The International Code of the Construction and Equipment of Ships Carrying Liquefied Gases in Bulk (IGC Code) limits the material of tanks that can store cryogenic substances such as LNG. Among the materials listed in the IGC Code, ASTM A553M-17 has been recently adopted as a material for LNG fuel tank projects because of its excellent mechanical properties at cryogenic temperatures. In shipyards, this material is being used to build tanks through Flux Cored Arc Welding (FCAW). However, there is a problem that magnetization occurs during welding and there is a big difference in welding quality depending on the welding position. In order to overcome this problem, this study intends to conduct basic research to apply laser welding to ASTM A553M-17 material. As a result of analyzing the bead shape according to laser BOP speed and Energy density performed in this study, it was confirmed that the penetration and energy density are proportional but the penetration and BOP speed are inverse proportional to some extent. In addition, a range of suitable welding speed and energy density were proposed for the 6.1mm thickness material performed in this study.

Due to stricter environmental regulations of the International Maritime Organization (IMO), the number of ships fueled by Liquefied Natural Gas (LNG) is rapidly increasing. The International Code of the Construction and Equipment of Ships Carrying Liquefied Gases in Bulk (IGC Code) limits the material of tanks that can store cryogenic substances such as LNG. Among the materials listed in the IGC Code, ASTM A553M-17 has been recently adopted as a material for LNG fuel tank projects because of its excellent mechanical properties at cryogenic temperatures. In shipyards, this material is being used to build tanks through Flux Cored Arc Welding (FCAW). However, there is a problem that magnetization occurs during welding and there is a big difference in welding quality depending on the welding position. In order to overcome this problem, this study intends to conduct basic research to apply laser welding to ASTM A553M-17 material. In Part I, the bead shape according to the welding output was analyzed and in PART II, ​​the penetration phenomenon according to the welding speed was analyzed after Bead on Plate (BOP) test. As a result of analyzing the bead shape according to laser power performed in this study, it was confirmed that the laser power and penetration depth are proportional to some extent. In addition, a range of suitable welding power was proposed for the 6.1mm thickness material performed in this study.

To cope with automobile exhaust gas regulations, ISG and charging control systems are applied to HEV vehicles for the purpose of improving fuel economy. These systems require quick charge-discharge performance of high current. Therefore, a Module of the AGM battery with high energy density and EDLC(Electric Double Layer Capacitor) with high power density are constructed to study the charging and discharging behavior. In CCA, which evaluates the starting performance at -18 oC & 30 oC with high current, EDLC contributed for about 8 sec at the beginning. At 0 oC CA (Charge Acceptance), the initial Charging current of the AGM/EDLC Module, is twice that of the AGM lead acid battery. To play the role of EDLC during high-current rapid charging and discharging, the condition of the AGM lead-acid battery is optimally maintained. As a result of a Standard of Battery Association of Japan (SBA) S0101 test, the service life of the Module of the AGM Lead Acid Battery/EDLC is found to improve by 2 times compared to that of the AGM Lead Acid Battery.

Conductive polymer composites with high electrical and mechanical properties are in demand for bipolar plates of phosphoric acid fuel cells (PAFC). In this study, composites based on natural graphite/fluorinated ethylene propylene (FEP) and different ratios of carbon black are mixed and hot formed into bars. The overall content of natural graphite is replaced by carbon black (0.2 wt% to 3.0 wt%). It is found that the addition of carbon black reduces electrical resistivity and density. The density of composite materials added with carbon black 3.0 wt% is 2.168 g/cm3, which is 0.017 g/cm3 less than that of non-additive composites. In-plane electrical resistivity is 7.68 μΩm and through-plane electrical resistivity is 27.66 μΩm. Compared with non-additive composites, in-plane electrical resistivity decreases by 95.7 % and through-plane decreases by 95.9 %. Also, the bending strength is about 30 % improved when carbon black is added at 2.0 wt% compared to non-additive cases. The decrease of electrical resistivity of composites is estimated to stem from the carbon black, which is a conductive material located between melted FEP and acts a path for electrons; the increasing mechanical properties are estimated to result from carbon black filling up pores in the composites.

This study has related to lightweight automobiles due to global warming with the reduction of fossil fuel reserves are rapidly progressing around the automobile industry. This study has revealed the relationship for the mechanical properties via the analyzed microstructure, precipitated phase variation of the wheel hub of a commercial vehicle manufactured using molten forging technology using A356 and A357 alloys, which are high-strength Al-Si-Mg base cast aluminum alloys. Differential scanning calorimetry has performed to analyze the precipitation amount of each alloy that influences the mechanical properties of aluminum alloy. The XRD analysis has measured for the microstructure's crystal phase on A356 and A357 alloys. In this paper has evaluated to compare the properties of the A356 alloy and the A357 alloy for the mechanical properties. The A356 alloy has confirmed that a microstructure is finer than A357 alloy, and a quantity of precipitated material is more than A357 alloy. Therefore, this study confirmed that the A356 alloy has better mechanical properties than the A357 alloy.

The objective of this study is to optimize the diameter of tubular shaft yoke and solid shaft yoke, which are the core components of Al IMS for xEV. The processes of both products were designed totally 6 steps to manufactured the shaft part and the yoke part. The diameter of solid shaft yoke and tubular shaft yoke were changed from 20mm to 25mm and from 30mm to 35mm, respectively. Al 6082 was applied to the material of both products. The friction condition between die and material was employed Oil_Cold (Aluminum) with reference to the library in the program. The results were analyzed and compared in terms of effective stress, effective strain, and nodal velocity characteristics. The effective strain value for manufacturing the yoke part was higher than the shaft part because its part has a complex geometry. The value of nodal velocity was also higher with high effective strain region. However, in 6 stage process of tubular shaft yoke, although it had the high effective strain value, the nodal velocity value was the lowest due to the piercing process. The effect of shaft part diameter on effective stress in the tubular shaft was difficult to observe, however, in the solid shaft yoke, when the shaft part of one increased, the effective stress value was increased due to the larger yoke size.

The purpose of this study is to analyze the temperature and heat resistance distribution, which is a criterion for evaluating the cooling performance, by using computer simulation of the cooling system combined with the CPU of the individual highest heat generation section, and use it as important data for the heat sink design. Using a single material of Al 6063-T5, which is an integral part of the desktop, fan and heat sink, fins and base, the analysis was carried out with various fin numbers, thicknesses, pitches and shapes of heat sinks. Ambient temperature, 25°C, heat source, 130W and cooling fan speed, 2500 rpm (50CFM) were used as boundary conditions, and heat transfer characteristics regarding temperature distribution and heat resistance were investigated using ANSYS Icepak. As a result, it has been found that as the number of fins of heat sink increases, the heat dissipation area increases to decrease heat resistance, and as the distance between each fin decreases, the ventilation resistance increases to decrease the flow intensity of the cooling air in contact with the heat dissipation area. The sunburst array also exhibits better heat transfer characteristics by obtaining a lower distribution of heat resistance with a cooling effect of about 10°C than the one-way basic array.

용천요는 중국 요업사 상 가장 중요한 요장 중 하나로 근 천년에 걸쳐 생산된 중국 고대 청자의 최전성기 전형으로 꼽힌다. 그 문화가 풍부하고 생산 규모가 커 남북요업의 문화교류와 융합의 본보기이자 중국 청자 공예발전의 역사의 집성이다. 용천요는 국내에서 널리 사용이 이루어졌는데, 궁정귀족에게 사랑을 받은 것은 물론 서민에게도 널리 쓰였다. 이 뿐만 아니라 수출용으로 대량 소비되어 세계 문명에 매우 큰 영향을 끼쳤다. 근 백 년 동안 용천요의 고고학적 조사와 발굴, 특히 신세기 들어 수많은 고고학적 작업이 진행되면서 충분한 데 이터가 축적되어 용천요의 발생․발전․쇠락의 전 과정을 알 수 있다.

As the solar power generation system expands, researches on the development and production technology of solar modules are being actively conducted. In addition, in the production of polysilicon for solar modules, a high-purity carbon electrode is essential, which greatly affects the performance and productivity of the solar module. This research is about the development of a carbon electrode used to manufacture high-purity polysilicon rod, which is essential for the manufacture of the photovoltaic modules. Fine graphite chuck is used as a carbon electrode. Generally, it is a consumable material that is used once and discarded. Therefore, this study aimed to develop an assembly-type high purity graphite chuck that can recycle some resources to dramatically improve the utilization of resources. In order to maintain the purity and performance of polysilicon, the composition and performance of the graphite chuck are important. The fine graphite chuck is manufactured through the high-purification process after precision machining, and the performance is confirmed through the component analysis of the specimen. At about 5,000 nm or more from the surface, the compositions of the sample appeared almost constant, and a high purity sample satisfying the target specification was obtained. In addition, it was confirmed that the cost reduction could be achieved by designing the graphite electrode as a separable type, and the results of this study can be applied to the design of the fine graphite chuck for the production of high purity polysilicon.

미세먼지발생 문제는 커다란 사회적 문제로 대두되고 있다. 선박에서는 주 추진 동력원으로 디젤엔진을 주로 사용하고 있다. 본 연구에서는 디젤엔진에서 발생하는 미세먼지로 알려진 입자상 물질을 줄이기 위해서 디젤엔진의 후처리시스템으로 사용 중인 DPF(디 젤미립자 필터, Diesel particulate filter)를 소개하고자 한다. DPF의 소재로는 Cordierite와 SiC (Silicon carbide)의 두 가지가 사용되고 있다. 본 논문에서는 SiC DPF에 사용되는 접합제의 물성 향상을 위해서 기존 접합제로 사용된 SiC 계열의 물질 대신 코디얼라이트를 사용하여 열 팽창계수 변화를 통한 고온 변형에 대한 열 내구성을 평가하였으며, 접합제와 Segment 사이의 결합을 결정짓는 바탕제에 주성분인 실리카 졸의 pH 변화에 따른 물성 변화를 확인하였다. 이를 기반으로 실리카 졸의 반응성을 높이기 위해 Siline계 커플링제를 첨가하거나 SiC를 일부 첨가함으로써 접합제의 물성 변화의 영향에 대해서 실험을 통하여 확인하였다.