Fluorine (F) recovery from wet process phosphoric acid (WPA) is essential for sustainable resource utilization and environmental protection. This work systematically investigates the F recovery mechanism by air stripping from three simulated systems: H3PO4- H2SiF6-H2O, H3PO4- HF-H2O, H3PO4- H2SiF6-HF-Al3+-H2O, and from two industrial systems: WPA and WPA-Al3+ under different stripping temperatures (60–110 ℃) and stripping times (0–120 min). The influence on the existence form of F, the content of Al3+ cations and the addition of active silica on the F removal rate in the phosphoric acid solution is studied by analyzing the changes in the contents of F, P and Si. The results indicate that the F in the form of H2SiF6 is more easily released from the phosphoric acid solution than that in the form of HF. While, the release of F is inhibited in the presence of the Al3+ in the solution due to the formation of Al-F complexes that are characterized by 19F NMR, 31Si NMR and FTIR techniques. Interestingly, the addition of active silica can promote the conversion of HF to H2SiF6 in the solution and significantly improve the release rate of F. The researching results can provide an important guidance for industrial practice of WPA.

Conductive polymer composites with high electrical and mechanical properties are in demand for bipolar plates of phosphoric acid fuel cells (PAFC). In this study, composites based on natural graphite/fluorinated ethylene propylene (FEP) and different ratios of carbon black are mixed and hot formed into bars. The overall content of natural graphite is replaced by carbon black (0.2 wt% to 3.0 wt%). It is found that the addition of carbon black reduces electrical resistivity and density. The density of composite materials added with carbon black 3.0 wt% is 2.168 g/cm3, which is 0.017 g/cm3 less than that of non-additive composites. In-plane electrical resistivity is 7.68 μΩm and through-plane electrical resistivity is 27.66 μΩm. Compared with non-additive composites, in-plane electrical resistivity decreases by 95.7 % and through-plane decreases by 95.9 %. Also, the bending strength is about 30 % improved when carbon black is added at 2.0 wt% compared to non-additive cases. The decrease of electrical resistivity of composites is estimated to stem from the carbon black, which is a conductive material located between melted FEP and acts a path for electrons; the increasing mechanical properties are estimated to result from carbon black filling up pores in the composites.

To improve the etch rate of Si3N4 thin film, H2SiF6 is added to increase etching rate by more than two times. SiO3H2 is gradually added to obtain a selectivity of 170: 1 at 600 ppm. Moreover, when SiO3H2 is added, the etching rate of the SiO2 thin film increases in proportion to the radius of the wafer. In Si3N4 thin film, there is no difference in the etching rate according to the position. However, in the SiO2 thin film, the etching rate increases in proportion to the radius. At the center of the wafer, the re-growth phenomenon is confirmed at a specific concentration or above. The difference in etch rates of SiO2 thin films and the reason for regrowth at these positions are interpreted as the result of the flow rate of the chemical solution replaced with fresh solution.

벼 이앙기별 인산에 의한 논조류 발생과 제초제에 의한 방제 효과는 다음과 같다. 1. 단작 및 이모작 벼 재배지에서 총출현 종수는 61종으로 녹조류 34종, 규조류 16종, 유글레나 7종, 그리고 남조류 4종이 발생하였고, 녹조류, 규조류는 이모작지가 많았고, 유글레나는 같았으며 남조류는 단작이 많았다. 2. 인산을 이앙전에 50%처리하고 분얼기에 50% 시비하였을 때 총인이 0.06 mg L-1로 가장 높았고, 조류 발생량도 무인산 대비 6월 6일 이앙한 구에서 14.8 mg 20 ml-1으로 3배 이상, 6월 20일에 이앙한 구에서 9.8 mg 20 ml-1 2배 이상 증가하였다. 3. 벼 생육단계별 분얼기, 유수형성기, 그리고 수잉기의 토양 인산의 함량은 관행 및 인산분시별로 유수형성기가 인산의 함량이 116.5~191.8 mg kg-1으로 가장 높은 경향이었으며 무 처리구에서는 15.5~29.1 mg kg-1로 낮았다. 이앙시기별로는 이앙이 빠를수록 높은 경향이었으며, 인산분시별로는 관행에 비해 분시하였을 때 높은 경향을 보였다. 4. 클로로필-a 함량은 6월 6일 이앙한 구에서는 제초제 처리 후 7일에 가장 낮은 6.3 mg m-3 이고, 7월 상순에 무처리구에서 75.8 mg m-3 로 가장 높았다. 6월 20일 이앙한 구에서는 제초제 처리후 7일에 가장 높은 경향이었으며 제초제 처리 후 14일과 21일은 감소하는 경향이었다 5. 논조류 억제율은 quinoclamine이 단작에서 59.2%, 이모 작에는 44.4%로 가장 높았으며, 다음으로 bromobutide + imazosulfuron + pyraclonil > benzobicyclon + mefenacet + peno xsulam >무처리 순이었다.

고온형 고분자 전해질 막 연료전지 (HT-PEMFC)는 100°C 이하의 저온 고분자전해질 운영 시스템에 비해 개선된 전극 반응 동역학, 뛰어난 물 및 열 관리, 연료 불순물에 대한 내성 및 폐열 이용과 같은 많은 이점을 제공한다. 그러나 HT-PEMFC는 구동 중 발생하는 물의 증발과 함께 분리막 내 인산이 증발하여 성능이 낮아진다는 단점이 있다. 때문에 본 연구에서는 이러한 인산의 유출에 대한 핫 프레스 유무, 전극 GDL 종류, 분리막 가수분해 조건, 셀 성능에 따른 영향을 인산의 비색정량을 통해 분석하였다. 그 결과 인산의 유출량은 주로 셀성능에 영향을 받으며 GDL이 치밀할수록 억제됨을 확인하였다.

Highly pathogenic avian influenza virus (HPAIV) damages vital organs and tissues, frequently leading to death in birds, and causes serious economic losses in the poultry industry. In addition, HPAIV can infect humans and other mammals, often with fatal outcomes. In this study, the virucidal efficacy of Clean-Zone®, which contains citric acid, malic acid and phosphoric acid, against avian influenza virus (AIV, H9N2) was investigated. Virucidal efficacy was determined by examining the viability of AIV after contact with the disinfectant in the allantoic membrane of chicken embryos. The disinfectant and AIV were reacted under hard water (HW) and organic matter suspension (OM) condition. AIV was inactivated with 200- and 50-fold dilutions of the disinfectant under HW and OM conditions, respectively. As the disinfectant, Clean-Zone®, has a virucidal efficacy against AIV, it can be used to prevent the spread of animal viral diseases.

A composite material was prepared for the bipolar plates of phosphoric acid fuel cells(PAFC) by hot pressing a flake type natural graphite powder as a filler material and a fluorine resin as a binder. Average particle sizes of the powders were 610.3, 401.6, 99.5, and 37.7 μm. The density of the composite increased from 2.25 to 2.72 g/cm3 as the graphite size increased from 37.7 to 610.3 μm. The anisotropy ratio of the composite increased from 1.8 to 490.9 as the graphite size increased. The flexural strength of the composite decreased from 15.60 to 8.94MPa as the graphite size increased. The porosity and the resistivity of the composite showed the same tendencies, and decreased as the graphite size increased. The lowest resistivity and porosity of the composite were 1.99 × 10−3 Ωcm and 2.02 %, respectively, when the graphite size was 401.6 μm. The flexural strength of the composite was 10.3MPa when the graphite size was 401.6 μm. The lowest resistance to electron mobility was well correlated with the composite with lowest porosity. It was possible the flaky large graphite particles survive after the hot pressing process.

대칭막이 가지는 유량 한계성과 비대칭막이 가지는 한계 압력 향상을 위한 분리막 제막 방법으로 인산 및 인산 에스테르 화합물을 포함한 PSF 고분자 지지층을 제조하였다. 활성층 두께와 구조를 조절하기 위하여 냉각판의 온도와 캐 스팅 용액의 두께가 조절되었으며 비대칭성 확보를 위하여 VIPS-NIPS 공정을 적용하였다. 상전이 안정성을 확인하기 위하여 용매 비교 실험이 진행되었으며 가장 비대칭 구조가 우수한 것은 NMP, 재현성이 뛰어난 용매는 DMAc로 확인 되었다. 운전 조건에 가장 민감하게 변화하였다. DMAc 용매 역시 Template 표 면층– 최소기공층– 비대칭 거대 기공층의 구조를 가지면서 BP 13 – 18 psig, 통기성 3140 cc/sec의 고유량 비대칭성 정밀여과막을 제조할 수 있었다.

The PBI membrane doped with phosphoric acid (PA) is one of the promising candidates for HT-PEMFC. The proton conductivity of PA doped PBI depends on the acid doping level (ADL). The method to fabricate porous PBI membrane using porogen were reported to increase the ADL. However, high ADL cause complete loss of the mechanical strength of the membranes. In this research, the dead-end porous PBI membranes were prepared using progen to increase the mechanical strength than porous PBI membrane and proton conductivity. The dead-end porous PBI membranes were investigated in terms of ionic conductivity, ADL, SEM and mechanical strength.

Porcine epidemic diarrhea virus (PEDV) causes porcine epidemic diarrhea (PED) and a considerable economic loss in the swine industry. In this study, the virucidal efficacy of a disinfectant composed of citric acid, benzalkonium chloride and phosphoric acid against PEDV was investigated. Virucidal efficacy was assessed as the infectivity of PEDV toward Vero cells after exposure of the virus to the disinfectant. PEDV was exposed to the disinfectant in the presence of either hard water (HW) or an organic matter suspension (OM). In HW condition, PEDV was inactivated by 600-fold dilutions of the disinfectant. In the presence of OM, the disinfectant showed virucidal activity after a 200-fold dilution. As the disinfectant possesses virucidal activity against PEDV, it should be an effective reagent to use to limit the spread of animal viral diseases.

침지법 상전이 공정 방법으로 polysulfone (PSF) 분리막을 제조하였다. PSF/NMP/PVP/phosphoric acid의 캐스팅 용액과 물 침전조를 이용하여 분리막을 제조하였다. 증기 유도 상전이법과 비용매 유도 상전이법을 연속하여 적용함으로서 캐스팅 용액에 첨가된 인산의 영향이 분리막의 구조 및 투과량에 미치는 영향을 살펴보았다. 미량의 인산의 첨가로도 평균 기공의 크기, 공극률, 수투과량의 증가를 볼 수 있었다. 또한 분리막의 구조가 치밀한 스펀지 형태의 구조에서 비대칭성이 향상된 구조로 변화함을 확인할 수 있었다. PSF/NMP/PVP/phosphoric acid/BE를 함유한 캐스팅 용액을 준비한 후 동일한 조건으로 증기 유도 상전이법과 비용매 유도 상전이법을 연속하여 적용하여 분리막을 제조하였다. BE의 첨가는 평균 기공의 크기를 거의 0.1 mum 정도 향상시키는 효과를 가져왔으며 수 투과 유량 또한 10~12L/cm2·min·bar 향상시키는 결과를 나타내었다.

The scope of this work investigates the relationship between the amount of oxygen-functional groups and hydrogen adsorption capacity with different concentrations of phosphoric acid. The amount of oxygen-functional groups of activated carbons (ACs) is characterized by X-ray photoelectron spectroscopy. The effects of chemical treatments on the pore structures of ACs are investigated by N2/77 K adsorption isotherms. The hydrogen adsorption capacity is measured by H2 isothermal adsorption at 298 K and 100 bar. In the results, the specific surface area and pore volume slightly decreased with the chemical treatments due to the pore collapsing behaviors, but the hydrogen storage capacity was increased by the oxygen-functional group characteristics of AC surfaces, resulting from enhanced electron acceptor-donor interaction at interfaces.

The capacity and long life of gel electrolyte batteries is connected with gas recombination producting PbO2 and Pb electrode. We were prepared with phosphoric acid gel electrolyte to know gel characteristics per density to assemble VRLA batteries. We studied by measuring electrolyte dispersion using Brewster-angle microscope(BAM), charge-discharge cycle and electrode structure using scanning election microscope(SEM) per electrolyte density. As a results, phosphoric acid density 1.210 was excellent gel dispersion in sol condition, electrode condition after fifty cycles in this study.

본 연구에서는 인산코팅된 것과 되지 않은 OXI-PAN섬유를 사용하여 제조된 무질서 배향의 OXI-PAN/페놀수지 복합재료를 불활성분위기의 여러 열처리온도에서 탄화하였을 때, 섬유표면에 인화합물의 존재 유.무가 복합재료의 물리적특성 및 미세구조 변화에 미치는 영향을 조사하였다. 두 종류 복합재료의 물리적특성 변화를 탄화온도 영향에 대한 섬유와 매트릭스 및 그 계면에서의 미세구조 거동변화와 기공형성의 관점에서 해석하였다. 열처리시 온도상승에 따라 섬유와 매트릭스 계면에서의 화학반응에 의해서 그 구분이 점차 사라지면서 국부적으로 치밀하고 균일한 상을 이루고 있는 것으로 조사되었다. 또한, 탄화 조건에서도 인산코팅은 OXI-PAN 섬유의 직경의 감소를 억제하고 열안정성을 향상시키므로 복합재료의 부피수축률을 줄이고 탄화수율을 증가시키는데도 어느정도 기여할 수 있으리라 판단되었다.

Optical resolution of aminoalcohols had been achived efficiently by use of (R)-2,2'-dihydroxy-l,1'-binaphtholphosphoric acid as the resolving agent in various organic solvents. Racemic aminoalcohols were resolved very easily and high enantiomer yield (about 70% e,e) in THF. On the other hand, absolute configuration of resolved aminoalcohol was (R)-configuration but one of the Valinnol and Phhenylglycinol was anti-type because of sterichindrance.Optical resolution of aminoalcohols had been achived efficiently by use of (R)-2,2'-dihydroxy-1,1'-binaphtholphosphoric acid as the resolving agent in various organic solvents. Racemic aminoalcohols were resolved very easily and high enantiomer yield (about 70% e,e) in THF. On the other hand, absolute configuration of resolved aminoalcohol was (R)-configuration but one of the Valinnol and Phhenylglycinol was anti-type because of sterichindrance.