Various electronic control parts and devices installed in electric vehicles have greatly improved the convenience of occupants, but electromagnetic waves emitted from electronic devices have greatly increased concerns about malfunctions, deterioration of performance, safety accidents, etc. There are two models of analysis. Case A is symmetrical about one axis of rotation. Case B has two axes of rotation. In this study, a flow analysis was conducted to find excellent flow conditions in the mixing process to develop a paint with excellent electromagnetic shielding and thermal insulation performance. The results of the flow analysis are reflected in manufacturing specifications and are intended to be used to develop high-quality systems.

Recently, at-home workouts, which allows people to exercise easily and comfortably at home without going to the gym, has been in the spotlight. Accordingly, a lot of household equipment is produced, but weight exercise equipment is limited in use at home because of its heavy weight or volume. Therefore, this paper proposes a new form of exercise equipment that can be used at home by transforming the exercise equipment used in the fitness center. The proposed mechanism replaces the weight part of the strength exercise device, which is the key to weight control, with an electric motor. Three major muscle exercise instruments (long pull machine, curl cable machine, and let down machine) were analyzed by dynamic analysis using a multipurpose dynamic program (DAFUL). This shows that the proposed equipment can perform various sports. Therefore, the proposed mechanism is expected to be applicable at home, and this study is expected to be rapidly mass-produced by emphasizing practicality.

Recent advances in technology using ultra-thin noble metal film in oxide/metal/oxide structures have attracted attention because this material is a promising alternative to meet the needs of transparent conduction electrodes (TCE). AZO/ Ag/AZO multilayer films are prepared by magnetron sputtering for Cu2ZnSn(S,Se)4 (CZTSSe) of kesterite solar cells. It is shown that the electrical and optical properties of the AZO/Ag/AZO multilayer films can be improved by the very low resistivity and surface plasmon effects due to the deposition of different thicknesses of Ag layer between oxide layers fixed at AZO 30 nm. The AZO/Ag/AZO multilayer films of Ag 15 nm show high mobility of 26.4 cm2/Vs and low resistivity and sheet resistance of 3.58*10−5 Ωcm and 5.0 Ω/sq. Also, the AZO/Ag (15 nm)/AZO multilayer film shows relatively high transmittance of more than 65% in the visible region. Through this, we fabricated CZTSSe thin film solar cells with 7.51% efficiency by improving the short-circuit current density and fill factor to 27.7 mV/cm2 and 62 %, respectively.

1. 개발도상국의 경우, 가치사슬 전반에 걸쳐 제약요인을 가지고 있는 경우가 많다. 이로 인해 가치사슬 일부 단계의 개선만으로는 그 파급효과가 제한적이다. 이로 인해 가치사슬 전반에 걸친 분석과 종합적인 개선 전략의 수립이 필요하다. 2. 선진 공여기관들은 개발도상국의 가치사슬 개선을 위해 여러 가지 분석 틀 및 개선전략 수립 틀을 가지고 가치사슬 사업을 추진하고 있다. 3. 본 연구에서는 한국의 농산물 가치사슬 개선 사업 기획 관리 방안을 제시하였다. 특히, 해당 기획관리 절차를 한국의 대표적인 무상원조 기관인 KOICA의 원조사업 기획 단계에 맞추어 구체적으로 제시하여 실제 현장에서 활용도를 높이고자 하였다. 해당 절차는 1) 대상 품목(혹은 품목군)의 선정, 2) 가치사슬 분석, 3) 개선전략 수립, 4) 기대효과 도출, 5) 성과관리(모니터링 및 평가) 방안의 도출 등으로 구성되었다. 4. 한국의 공여기관들은 이 절차를 바탕으로 농산물 가치사슬 개선 사업의 기획과 시행에 필요한 사항들을 점검 및 확인 할 수 있을 것으로 기대된다. 또한, 현장에서의 활용을 통해 해당 절차를 보다 효과적으로 발전시킬 수 있을 것으로 기대 한다.

PURPOSES : In this paper, pedestrian-oriented time assured traffic operation (POTATO), adopted in Korea at a single crossing pedestrianoriented operating area, is explored and applied to a simulation experiment and test site to verify the operation efficiency. METHODS : Three candidate plans are presented as a method to operate pedestrian-oriented signal operations that can overcome the restrictions on signal controllers in Korea. The selected POTATO and TOD signal operations were compared and analyzed. The delay and pedestrian queues, present length, and number of times were used as comparative indices. RESULTS : Scenario-specific simulations confirmed that the delay, compared to TOD signal operation, was reduced by up to 5 s/ped depending on the vehicle traffic volume and the number of pedestrians. For the vehicle delay, the results increased up to 8.99 s/veh, depending on the traffic volume of the vehicles and pedestrians. As a result of the test site operation, POTATO operation improved by 5.12 s/ped (approximately 46.69% improvement) compared to TOD operation in the hours commuting to school and by 2.84 s/ped in the hours commuting from school (approximately 51.13% improvement). In case of vehicle delay, the delay increased by 2.35 s/veh (approximately 64.39%) in the hours commuting to school and 1.20 s/veh (approximately 21.11%) in the hours commuting from school compared to the TOD operation. CONCLUSIONS : Through simulations and test site pilot operation verifications, the effects of pedestrian delay improvement were more positive if POTATO proposed in this study was low in vehicle traffic.

PURPOSES : This paper is to deliver an engineering design guide currently unavailable that highway engineers can refer to when they need to determine the safe distance between the starting point of the underground highway in a metropolitan area and the access points of the adjacent highway. METHODS : The distance between two different highway points should be sufficiently far to support the number of lane changes that drivers may take comfortably at the cruising speed in critical traffic conditions. RESULTS : The proper distance for the selected case study is calculated to be 160 and 200 m at the cruising speeds of 40 km/h and 50 km/h, respectively, without significant increase in potential conflicts estimated by the combination of the VISSIM and SSAM analysis. CONCLUSIONS : The proposed design method can be referred in urban metropolitan areas where no specific design guide is yet available, and it would prevent the unnecessary increase in construction costs and encourage private-public partnership highway businesses.

With few reported cases, cystic hygroma is known to occur mainly in patients under the age of two years. Cystic hygroma can eventuate in any area; however, it mostly occurs in the cervicofacial area. If cystic hygroma occurs in this area, then the lesion may be related to the vital structures. Therefore, a complete surgical resection may be impossible and difficult to perform. This incident affects the high recurrence rate of cystic hygroma. The purpose of this report is to present a case of cystic hygroma occurring on the left side of the neck of a 47-year-old male patient as well as a review of literatures.

본 연구는 성별에 따른 2등급 한우의 소분할 부위별 보수력, 가열감량, 전단력 및 관능 특성을 조사하고자 실시하였다. 한우 15두(암소 5두, 수소 5두 및 거세우 5두)를 도축한 다음 등급 판정을 한 후 39개 소분할 부위를 발골하여 육질 특성을 조사하였다. 2등급 한우의 소분할 부위별 보수력은 46.97~63.16%를 나타내었으며, 가열감량은 52.44~71.58%로 안심살과 꽃등심살 부위를 제외한 부위에서 유의적인 차이가 나타나지 않았다(p>0.05). 전단력은 2.36~6.80 kg/cm2으로 암소의 안심살, 윗등심살, 꽃등심살, 아래등심살, 부채살, 앞다리살, 갈비덧살, 삼각살, 업진살, 꽃갈비 부위에서 수소와 거세우에 비해 낮은 전단력을 나타내었으며(p<0.05), 거세우의 살치살, 꾸리살, 부채덮개살, 우둔살, 설깃살, 설깃머리살, 도가니살, 양지머리, 차돌박이, 뒷사태, 안창살 부위는 수소와 암소에 비해 낮은 전단력을 나타내었다(p<0.05). 풍미는 윗등심살, 아래등심살, 홍두깨 살, 보섭살, 양지머리 및 차돌박이 부위에서 수소가 암소와 거세우에 비해 낮은 점수를 받았으며, 나머지 부위에서 유의적인 차이가 나타나지 않았다(p>0.05). 저작감은 암소의 아래등심살, 채끝살, 목심살, 꾸리살, 부채살, 설깃머리살 및 차돌박이 부위에서 수소와 거세우에 비해 높은 점수를 받았으며(p<0.05), 거세우의 치마살 및 뭉치사태 부위가 암소와 수소에 비해 높은 점수를 받았다(p<0.05). 종합적인 기호도는 암소의 채끝살, 꾸리살 및 부채살 부위가 수소와 거세우에 비해 높은 점수를 받았으며(p<0.05), 거세우의 윗등심살, 살치살, 앞다리살, 치마살 및 앞치마살 부위가 암소와 수소에 비해 높은 점수를 받았다(p<0.05). 2등급 한우고기는 수소가 암소와 거세우에 비해 높은 보수력을 나타내었으며, 암소와 거세우가 수소보다 낮은 전단력을 나타내었으며, 풍미에서 높은 점수를 받은 거세우의 부위와 저작감에서 높은 점수를 받은 암소의 부위는 종합적인 기호도에서 도 높은 점수를 받았다.

한반도 풍력자원의 연간 변동성을 파악하기 위하여 한국 기상청의 아시아권 및 한반도권 지역예보모델 해석자료를 초기 기 상장으로 연계한 UM-WRF 수치기상예측 모델로 2010년부터 2018년까지의 풍력자원지도를 생산하였다. 풍력자원지도의 풍력발전량 예측정확도를 확인하기 위해 가동 중인 모든 풍력터빈의 발전량을 예측하고 전력거래소의 월간 발전량 기록과 비교검증하였으며, R2=0.83의 높은 일치도를 확인하였다. 한반도 육상 및 해상의 연간 풍속 변동성은 각각 COV = 11.4%와 4.3%로 파악되었으며, 특히 풍력자원이 우수한 고산지대의 변동성이 큰 것으로 나타났다. 풍력보급의 증가에 따라서 전력계통에 미치는 변동성의 우려가 커지고 있기 때문에 지속적으로 장기간의 고해상도 풍력자원지도를 생산하고 발전량 검증을 거쳐 발전량 변동성을 정밀하고도 정량적으로 파 악할 필요가 있다.

본 연구에서는 폴리머 시멘트 모르타르의 인장성능을 개선하기 위하여 PVA 섬유를 적용하고자 하였다. PVA 섬유 혼입량에 따른 재료특성을 검토하여, 섬유보강 폴리머 시멘트 모르타르의 제조 가이드라인을 제공하고자 하였다. 폴리머 시멘트 모르타르의 제조를 위하여 친수성의 합성수지(SR)를 사용하였다. 실험에 사용된 변수로 (W+SR)/C비를 고정하여, 사용물에 대한 합성수지의 치환율을 일정하게 증가시켜 사용하였다. PVA 섬유의 혼입량은 각각의 실험체에 0%,1%,2%를 혼입하여 실험을 수행하였다. 재료특성 실험으로는 압축강도시험, 쪼갬 인장강도시험, 휨 강도 시험을 수행하였다. 폴리머 시멘트 모르타르에 PVA 섬유를 혼입하면 쪼갬 인장강도 및 휨 강도가 증가하는 것을 확인 하였다. 따라서, 본 연구결과는 합성수지 혼입 폴리머 시멘트 모르타르의 인장성능 개선을 위한 PVA섬유 혼입시 제조 가이드라인으로 활용이 가능할 것으로 판단된다.

In this study, a controlled atmosphere (CA) storage system is proposed as a storage method for prolonging processing period. Persimmon was placed in CA storage at 0.5oC±0.5 for 92 d. The qualities of the stored persimmons were compared to determine the possibility of extending shelf life. ‘Sangjudungsi,’ which was harvested on October 26, 2017, was applied to the persimmons. In order to compare differences according to size, the persimmons were classified into Size No. 2 (170 g) and Size No. 3 (145 g). In the result, the yellowness of CA-stored persimmons was 26.3% lower than that of cold-stored ones, confirming that after-ripening was delayed. The firmness of CAstored and Size No. 3 persimmon was higher than that of cold-stored and Size No. 2 persimmon. Tannin decreased significantly in cold storage, but it tended to increase in CA storage. The sugar content of Size No. 3 was lower than that of Size No. 2, but there was no difference in tendencies according to the storage method. Weight loss in CA storage was lower than that in cold storage. A comparison of color difference, firmness, sugar content, tannin, and weight loss ratio showed that CA storage was more effective in improving shelf life than cold storage.

Recently, home workout has attracted attention as it can be done easily and conveniently at home. Accordingly, many types of home workout equipment are produced but, these kinds of exercise equipment using dumbbells or weights are too heavy to use for at-home-workout and they are too bulky in size. This paper studies a form of exercise done at home which is using a motor instead of dumbbells and weights that are originally used in the exercise equipment. DAFUL, a multi-body dynamics analysis program, is used to verify the dynamic performance of the proposed equipment. Therefore, motor-based exercise equipment is expected to be smaller than existing exercise equipment and more suitable for use at home.