WC-CrC-Ni coatings were prepared by nine processes of the Taguchi program with three levels for the four spray parameters: spray distance, flow rates of hydrogen and oxygen, and powder feed rate. The optimal coating process (OCP) was oxygen flow rate of 38 FMR, hydrogen flow rate of 53 FMR, powder feed rate of 25 g/min, and spray distance of 7 inches. Hardness of 1150 Hv and porosity of 1.2 %, were obtained by OCP; these are better results compared with the highest 1033 Hv and the lowest 1.5% porosity obtained by nine processes of the Taguchi program. Friction coefficient of the WC-CrC-Ni coating decreased from 0.36 ± 0.07 at 25 oC to 0.23 ± 0.07 at 450 oC. These values were smaller than those of the EHC (electrolytic hard chrome) plating at both temperatures due to lubrication from the oxide debris. The wear trace and wear depth of the coating are smaller than those of the EHC at both temperatures. Pitting was not found in the WC-CrC-Ni coating sample, while it did appear in the EHC sample.

This study was carried out to extract ginsenosides in by-products from honeyed red ginseng. Response surface methodology (RSM) was used to optimize the extraction conditions. Based on D-optimal design, independent variables were ethanol (extraction solvent) concentration (30-90%, v/v), extraction temperature (25-70oC), and extraction time (5-11 h). Extraction yield (Y1) and total ginsenosides (Y2) in the extract were analyzed as dependent variables. Results found that extraction yield increased with increasing extraction temperature and time, whereas it was decreased with increasing ethanol concentration. Similar trends were found for the content of ginsenosides in the extracts, except for ethanol concentration, which was increased with increasing ethanol concentration. Regression equations derived from RSM were suggested to coincide well with the results from the experiments. The optimal extraction conditions for extraction yield and total ginsenosides were an extraction temperature of 56.94oC, ethanol concentration of 57.90%, and extraction time of 11 h. Under these conditions, extraction yield and total ginsenoside contents were predicted to be 84.52% and 9.54 mg/g, respectively.

This study investigates the analysis algorithm for developing an optimum hull form with minimum wave resistance by using the practical application of one minus prismatic. In this algorithm the potential-based panel method was adopted to get the wave resistance coefficient as the objective function and SQP method was applied as an optimizer to get the optimum hull form. As an target ship, the series 60(CB=0.6) was taken into account and LBP(length between perpendiculars) of the ship was changed in the direction including a central parallel portion. To verity the validity of this study, the results of the numerical analyses were compared with experimental data.

This study was conducted to optimize the conditions of a sweet rice paste as a replacement of red bean paste recipe using the central composite design of response surface methodology (RSM). Ten experimental recipes with two reference points (rice flour and sugar), were selected, and the physical and sensory characteristics of a sweet rice paste were measured. In the Rapid Visco Analyzer test, breakdown value was the highest in rice flour (105.73 RVU). Sweetness significantly increased with addition of sugar contents (p<0.0002) and viscosity increased with addition of rice flour contents (p<0.0185). Moisture contents decreased with increasing contents of rice flour and sugar, whereas yellowness and redness tend to increase. In the sensory evaluation test, quadratic models for color (p<0.01865), sweetness (p<0.0399), thickness (p<0.0073), and overall acceptability (p<0.0249) were approved as independent for the rice flour and sugar contents. In conclusion, the optimal mixing ratio of sweet rice paste was determined to be 45.38 g of rice flour and 77.95 g of sugar.

본 논문에서는 반응표면법과 다목적최적화 기법을 이용한 유한요소모델개선기법의 절차를 제안하고 이를 저층의 철근콘 크리트건물의 모델개선에 적용하였다. 대상건물은 전단벽 신설 및 댐퍼부착을 위한 부재의 강재보강을 통해 내진보강이 이 루어진 건물로서 보강전후에 소형 가진기를 이용한 진동실험을 실시하여 동특성을 구하였다. 대상건물의 개선에 사용된 변 수는 기존콘크리트, 신규타설된 콘크리트, 조적의 탄성계수, 신축줄눈부의 스프링계수, 강재보강된 부재의 유효강성비이다. 보강전후 건물의 초기모델을 구축한 후 중심합성법에 따라 개선변수의 값을 변화시키면서 얻은 해석결과를 통해 고유진동 수의 오차와 모드형상의 오차를 나타내는 2개의 반응함수를 구하고, 이를 다목적최적화의 목적함수로 사용하였다

The study for reducing friction in elevation motion of a large television stand using over 50 inches is performed in this paper. The first study attempted to reduce the frictional force the gas seal lip technology. The second study is for optimized piston structure development by comparison pipe orifice and labyrinth orifice. As the result of the first study, in the gas seal lip technology, the outer-inner diameter of Ø20 × Ø8 in the test result of hollow rod is revealed more proper if the weight of 50 inch television assumed as 30. As the result of the second study, the optimized piston structure development through experiment is fixed orifice specification as labyrinth orifice because pipe orifice is founded slip up/down phenomenon of the Ø0.4~1.0 orifice and the labyrinth orifice is not founded that of the Ø0.4~0.6 orifice both tests on 300 mm intervals.

PURPOSES : The objective of this study is to develop an optimized method of mix design for rapid-set lightweight-formed mortar mix. To achieve this objective, the workability, setting time, and compressive strength of mixes under various conditions of mix design were evaluated. METHODS: The water-bonder ratio, fly-ash substitution ratio, and forming agent injection amount were selected as design variables in the study. The fluidity, setting time, density, and strength of the mortar mix were considered as major evaluation criteria of the mixture, and were subsequently utilized to evaluate the characteristics of the mortar mix under various conditions. RESULTS : The observations made from the mix design process are as follows: 1) the air content and fluidity increase as the forming agent ratio and forming agent ratio increase, respectively; 2) the maximum air content is approximately 20%; 3) the accelerating agent decreases the fluidity of the mortar mix by 15% on average; 4) the forming agent injection ratio and fly-ash substitution ratio yield significant effects on the initial and final set times of the mortar mix; 5) as the forming agent injection ratio and fly-ash substitution ratio increase, the compressive strength of the mortar mix decreases; and 6) the 28-day compressive strengths of the forming agent injection ratio and fly-ash substitution ratio yield the most significant effects. CONCLUSIONS: It is concluded that the governing design variables for the rapid-set lightweight-formed mortar mix are the forming agent injection ratio and fly-ash substitution ratio.

Surge pressure is created by rapid change of flow rate due to operation of hydraulic component or accident of pipeline. Proper control of surge pressure in distribution system is important because it can damage pipeline and may have the potential to degrade water quality by pipe leakage due to surge pressure. Surge relief valve(SRV) is one of the most widely used devices and it is important to determine proper parameters for SRV’s installation and operation. In this research, determining optimum parameters affecting performance of the SRV were investigated. We proposed the methodology for finding combination of parameters for best performance of the SRV. Therefore, the objective function for evaluate fitness of candidate parameters and surge pressure simulation software was developed to validate proposed parameters for SRV. The developed software was integrated into genetic algorithm(GA) to find best combination of parameters.

Structural dynamic system involves random variables conditions such as material property, geometric parameters and applied loads. This uncertainties result from the structural parameter are carefully considered the dynamic structural response in displacement, stress, and natural frequencies. The random vibrational system must be designed to withstand a certain amount of the fluctuation with respect to the uncertainties. Harmonic response of a spring-mass system is mathematically modelled with the probabilistic finite element method using the Monte Carlo simulation. The aim of this paper is to find the optimal lowest frequency for the spring-mass system with random input variables and response parameters to the displacements. The probabilistic design is carried out using ANSYS probabilistic design module in a commercial application software and then the optimal design is sequentially solved. An efficient and practical optimal design evaluation method is proposed for the design of the harmonic system. The numerical results are obtained where the next highest frequency of the system and displacements treated as constraints.

An injection unit is the important part which guide the melted resine into the mold. Once injection molding is performed, there will be a pressure of 33 MPa built up inside of injection cylinder body. It was confirmed that the crack occurs by internal stress on the 9 mm material when the machine is used for long time. Because the cylinder rod has material thickness of 9~12 mm during manufacturing process on the cylinder body, there would be 3 mm thickness differences. In this experiment, IDEAS, a computer aided structure analysis software, is used to present the optimized design condition. Insert rod with inner diameter of 9 mm was set as a normal and vary 3 mm in x, y axis direction. When the internal pressure of 33 MPa occurs at the injection unit, fix the x and y direction and find out the stress acting only in z axis. It was confirmed that the stress of 45~82 N/mm 2 was built up when the left of cylinder body had been set 9 mm by using a structure analysis. Also, it has been verified the thickness of the material on the left need to be greater and equal than 12 mm to prevent a material crack by an internal stress.

Numerical analysis using k-ε model of unsteady state was performed to decide the optimal shape of power auxiliary apparatus in automotive engine. In order to obtain auxiliary electric power using coolant in automotive engine, shapes of 3 Types were compared. Furthermore to achieve the confidence of numerical analysis, the results of numerical analysis was compared with those of experiment. As the results, it showed that accuracy of numerical analysis was about 85~98%. Further the optimal shape, in this study, was Type-1, which had outer rounding R32.5, among 3 Types.

본 연구는 표면 반응 분석법을 이용하여 곤드레 데치기 최적 공정 조건을 확립하고 각각의 공정으로부터 생산된 곤드레 추출물로부터 총 페놀 화합물, 플라보노이드의 함량, DPPH 라디칼 소거능 을 분석하였다. 최적 공정 확립을 위한 데치기 공정 범위로 온도는 70℃ - 99℃, 시간은 70 - 170 sec. 로 하였다. 데치기 공정 후 총 페놀 함량의 범위는 13.00 - 35.48 mg/g 이고 최대 예측 총 페놀함량은 35.48 mg/g, 총 페놀 함량의 경향을 보면 데치기 온도에 따라 급격히 감소하다가 증가하는 것으로 보 여 지므로 온도에 의해 더 많은 영향을 받는 것으로 나타난다. 플라보노이드의 함량의 범위는 2.31 - 8.38 mg/g 이고 최대 예측 플라보노이드 함량은 8.38 mg/g 이었다. 플라보노이드 함량의 경향을 보면 데치기 시간에 따라 서서히 증가하다가 급격히 감소하는 것으로 보여 지므로 시간에 의해 더 많은 영향 을 받는 것으로 나타났다. DPPH 라디칼 소거능의 범위는 42.10 - 67.14%이고 최대 예측 DPPH 라디 칼 소거능은 67.14%로 측정 되었다. DPPH의 경향을 보면 데치기 온도에 따라 증가하다가 급격히 감소 하는 것으로 보여 지므로 온도에 의해 더 많은 영향을 받는 것으로 나타난다. 따라서 데치기 공정 최적 조건은 온도 85℃와 시간 150 sec. 로 결정되었다.

Coagulation/precipitation process has been widely used for the removal of phosphate within domestic wastewater. Although Fe and Al are typical coagulants used for phosphate removal, these have some shortages such as color problem and low sedimentation velocity. In this study, both Fe and Al were used to overcome the shortages caused by using single one, and anionic polymer coagulant was additionally used to enhance sedimentation velocity of the precipitate formed. Batch experiments using a jar test were conducted with real wastewater, which was an effluent of the second sedimentation tank in domestic wastewater treatment plant. Response Surface Methodology was used to examine the responsibility of each parameter on phosphate removal as well as to optimize the dosage of the three coagulants. Economic analysis was also done on the basis of selling prices of the coagulants in the field. Phosphate removal efficiency of Fe(III) was 30% higher than those of Fe(II). Considering chemical price, optimum dosage for achieving residual phosphate concentration below 0.2 mg/L were determined to be 18.14 mg/L of Fe(III), 2.60 mg/L of Al, and 1.64 mg/L of polymer coagulant.

A membrane module including grid was designed and introduced to MBR (membrane bio-reactor) for the purpose of better control of membrane fouling. It could be anticipated that the grid enhances the shear force of fluid-air mixture into the membrane surface by even-distributing the fluid-air to the membrane module. As MLSS concentration, packing density which is expressed in the ratio of the housing and the cross-sectional area of membrane fibers (Am/At) and air-flow rate were changed, membrane foulings were checked by monitoring fouling resistances. The total fouling resistance (Rc+Rf) without grid installation (i.e., control) was 2.13×1012 m-1 , whereas it was reduced to 1.69×1012 m-1 after the grid was installed. Regardless of the grid installation, the Rc+Rf increased as the packing density increased from 0.09 to 0.28, however, the increment of resistance for the grid installation was less than that of the control. Increase in the air flow rate did not always guarantee the reduction of fouling resistance, indicating that the higher air flow rate can partially de-flocculate the activated sludge flocs, which led to severer membrane fouling. Consequently, installation of grids inside the housing have brought a beneficial effect on membrane fouling and optimum air flow rate is important to keep the membrane lowering fouling.

Seismic design of braced frames that simultaneously considers economic issues and structural performance represents a rather complicated engineering problem, and therefore, a systematic and well-established methodology is needed. This study proposes a multi-objective seismic design method for an inverted V-braced frame with suspended zipper struts that uses the non-dominated sorting genetic algorithm-II(NSGA-II). The structural weight and the maximum inter-story drift ratio as the objective functions are simultaneously minimized to optimize the cost and seismic performance of the structure. To investigate which of strength- and performance-based design criteria for braced frames is the critical design condition, the constraint conditions on the two design methods are simultaneously considered (i.e. the constraint conditions based on the strength and plastic deformation of members). The linear static analysis method and the nonlinear static analysis method are adopted to check the strength- and plastic deformation-based design constraints, respectively. The proposed optimal method are applied to three- and six-story steel frame examples, and the solutions improved for the considered objective functions were found.

Stress on plates may increase in the neighborhood the edges or the holes for rivets or bolts. Excessive stress concentration may lead to severe breakage of the plates. Thus, it is important to conduct optimization of arrangement of holes at the design stage. In this paper, accuracy of FEM analysis was examined for such stress concentration . By changing the hole size on a narrow plate, change of the stress concentration factor(K) was investigated. Additionally, the same experiment was conducted about series of multiple holes on plate to investigate interaction between the adjacent holes. Then, the FEM results were compared to the reference predictions respectively. Finally, a method by which simple stress concentrating situations can be optimized, will be suggested. This method was examined by FEM, and showed similar tendency with the expectation. Therefore, this method can be valuable when arranging the holes on a plate.

The objective of this study was to optimize analytical methods for ochratoxin A (OTA) and zearalenone (ZEA) in rice straw silage and winter forage crops using ultra-high performance liquid chromatography (UHPLC). Samples free of mycotoxins were spiked with 50 μg/kg, 250 μg/kg, or 500 μg/kg of OTA and 300 μg/kg, 1500 μg/kg, or 3000 μg/kg of ZEA. OTA and ZEA were extracted by acetonitrile and cleaned-up using an immunoaffinity column. They were then subjected to analysis with UHPLC equipped with a fluorescence detector. The correlation coefficients of calibration curves showed high linearity (R2 ≧ 0.9999 for OTA and R2≧0.9995 for ZEA). The limit of detection and quantification were 0.1 μg/kg and 0.3 μg/kg, respectively, for OTA and 5 μg/kg and 16.7 μg/kg, respectively, for ZEA. The recovery and relative standard deviation (RSD) of OTA were as follows: rice straw = 84.23~95.33%, 2.59~4.77%; Italian ryegrass = 79.02~95%, 0.86~5.83%; barley = 74.93~97%, 0.85~9.19%; rye = 77.99~ 96.67%, 0.33~6.26%. The recovery and RSD of ZEA were: rice straw = 109.6~114.22%, 0.67~7.15%; Italian ryegrass = 98.01~109.44%, 1.65~4.81%; barley = 98~113.53%, 0.25~5.85%; rye = 90.44~108.56%, 2.5~4.66%. They both satisfied the standards of European Commission criteria (EC 401-2006) for quantitative analysis. These results showed that the optimized methods could be used for mycotoxin analysis of forages.