This study was conducted to estimate the effects of the forage process on rumen fermentation characteristics and greenhouse gas emissions of rye. Rye was grown at the Taeyoung Livestock farm and harvested at the heading stage. The harvested rye (5 kg) was sub-sampled for fresh forage, hay, and silage in triplicates. The sub-sampled rye was freeze-dried or air-dried for fresh forage or rye hay, respectively. For rye silage, the sub-sampled rye forage was ensiled into a 10 L mini bucket silo and stored for 90 days. For 72 h rumen incubation, each forage (0.3 g) was placed into the incubation bottle with the rumen mixture (30 mL) in quadruplicates. After the incubation, total gas was measured and sub-sampled for CO2 and CH4 analyses, and the bottle content was centrifuged for in vitro digestibilities of dry matter (IVDMD) and neutral detergent fiber (IVNDFD), and rumen fermentation characteristics. Silage had higher crude protein, crude ash, and acid detergent fiber concentrations than fresh forage and hay but lower non-fiber carbohydrates and relative feed value (p<0.05). And, silage had higher lactic acid bacteria than the other forages but lower pH (p<0.05). After 72 h incubation in the rumen, fresh forage had higher IVDMD and butyrate content than the other forages (p<0.05). However, silage had higher rumen pH and propionate content than the other forages but lower A:P ratio (p<0.05). Regarding greenhouse gases, silage had lowest total gas (mL/g DMD and NDFD) and CH4 (mL/g DMD and NDFD) emissions, while fresh forage had lowest CO2 (mL/g DMD) emission (p<0.05). Therefore, this study concluded that the ensiling process of rye can effectively mitigate greenhouse gas emissions of Hanwoo.

In this study, the effect of Distribution efficiency through the fishery production base distribution center (FPC) on the production site board facility was studied. FPC is a new distribution system for Korean fishery products that has been promoted in earnest since 2012, and in this study, the effect before and after the introduction of FPC was analyzed using the DID (Difference in Difference) model for the effect of FPC in the fishery industry. The results of analysis shows that in the case of Wando Geumil FPC, the volume and unit price of consignment sales decreased during the analysis period, which was statistically significant. In the case of Sokcho FPC, the volume of consignment sales decreased during the analysis period, which was statistically insignificant. But the unit price of consignment sales rose during the analysis period, which was statistically significant. In the case of Gyeongju FPC, the volume of consignment sales increased during the analysis period, which was statistically significant at the 90% confidence level. But the unit price of consignment sales fell during the analysis period, which was statistically significant.

Black soldier fly (BSF, Hermetia illucens) has been noted as an excellent feed ingredient. However, there is limited information on rearing and processing technology. Thus, this study was conducted to evaluate the substrates for rearing BSF and the optimal processing method for BSF performance. Study separated as 2 experiment, BSF rearing and drying method(Exp 1.) and EP-processing method(exp 2.). During the study, 30 clutches were reared, with 10 per substrate. Three substrates, namely food waste (FW), tofu by-product (TF), and vegetable waste with two drying methods, namely hot air dry (AD) and microwave dry (MW) at expanding (EP) ratios of 5:5 and 7:3, were examined by evaluating their rearing performance, nutrient contents, in vitro digestibility and lipid oxidation stability during storage (0, 14 and 28 days). In experiment 1, the rearing substrates and drying methods were evaluated. Compared with that of conventional methods (FW, AD), the TF substrates and MW method showed higher dry matter contents (3.43%) and in vitro digestibility (1.62%) but lower ether extract contents(3.53%; p<0.05). However, the malondialdehyde (MDA) concentration under MW treatments decreased during storage (5.77%, 4.69% and 3.24%; p<0.05). In experiment 2, compared with that of the 7:3 EP-BSF ratio, the 5:5 EP-BSF ratio showed higher in vitro digestibility (2.70%) and lower MDA concentration during storage (19.19%, 7.96% and 6.42%; p<0.05). In conclusion, the optimal conditions for BSF rearing and ensuring product quality were TF substrates, MW methods and a 5:5 corn:BSF ratio. Therefore, the optimal conditions for producing EP-BSF can present an excellent feed ingredient alternative for swine feed.

현대 해양 산업은 기술적 발전을 통해 신속한 발전을 이루고 있다. 이러한 발전을 주도하는 주요 기술 중 하나는 데이터 처리 기술이며, 이 중 자연어 처리 기법은 사람의 언어를 기계가 이해하고 처리할 수 있도록 하는 기술이다. 본 연구는 자연어 처리 기법을 통해 해양안전심판원의 재결서를 분석하여 이미 재결이 이루어진 선박 충돌사고의 원인 제공 비율을 학습한 후, 새로운 재결서를 입력 하면 원인 제공 비율을 예측하는 모델을 개발하고자 하였다. 이 모델은 사고 당시 적용되는 항법과 원인 제공 비율에 영향을 주는 핵심 키워드의 가중치를 이용하여 사고의 원인 제공 비율을 계산하는 방식으로 구성하였다. 이 연구는 이러한 방식을 통해 제작한 모델의 정 확도를 분석하고, 모델의 실무 적용 가능성을 검토함과 동시에 충돌사고 재발 방지 및 해양사고 당사자들의 분쟁 해결에 기여할 것으로 기대한다.

본 논문에서는 역학적 변수들을 측정하는 방안으로 디지털 이미지 프로세싱과 강형식 기반의 MLS 차분법을 융합한 DIP-MLS 시 험법을 소개하고 추적점의 위치와 이미지 해상도에 대한 영향을 분석하였다. 이 방법은 디지털 이미지 프로세싱을 통해 시료에 부착 된 표적의 변위 값을 측정하고 이를 절점만 사용하는 MLS 차분법 모델의 절점 변위로 분배하여 대상 물체의 응력, 변형률과 같은 역 학적 변수를 계산한다. 디지털 이미지 프로세싱을 통해서 표적의 무게중심 점의 변위를 측정하기 위한 효과적인 방안을 제시하였다. 이미지 기반의 표적 변위를 이용한 MLS 차분법의 역학적 변수의 계산은 정확한 시험체의 변위 이력을 취득하고 정형성이 부족한 추 적 점들의 변위를 이용해 mesh나 grid의 제약 없이 임의의 위치에서 역학적 변수를 쉽게 계산할 수 있다. 개발된 시험법은 고무 보의 3 점 휨 실험을 대상으로 센서의 계측 결과와 DIP-MLS 시험법의 결과를 비교하고, 추가적으로 MLS 차분법만으로 시뮬레이션한 수치 해석 결과와도 비교하여 검증하였다. 이를 통해 개발된 기법이 대변형 이전까지의 단계에서 실제 시험을 정확히 모사하고 수치해석 결과와도 잘 일치하는 것을 확인하였다. 또한, 모서리 점을 추가한 46개의 추적점을 DIP-MLS 시험법에 적용하고 표적의 내부 점만을 이용한 경우와 비교하여 경계 점의 영향을 분석하였고 이 시험법을 위한 최적의 이미지 해상도를 제시하였다. 이를 통해 직접 실험이 나 기존의 요소망 기반 시뮬레이션의 부족한 점을 효율적으로 보완하는 한편, 실험-시뮬레이션 과정의 디지털화가 상당한 수준까지 가능하다는 것을 보여주었다.

Painting pretreatment is an important task in determining the life of painting as it removes rust or foreign substances from the painting surface and gives adhesion between the painting surface and the painting surface. Since painting pretreatment is an important task, IMO strictly requires that the painting pretreatment surface be maintained at a Sa 2.5 grade and the surface roughness is 30μm~75μm. Painting pre-processing is an important task that determines the lifespan of a painting, but it is done through visual inspection by the inspector, and the quality varies depending on the inspector. In this study, in order to develop a quality measurement system for the painting pretreatment surface, Matlab2023b was used to determine the range of appropriate quality brightness by comparing the brightness of the painting pretreatment surface and surface roughness.

This study investigated the effects of exposure frequency, depth of processing, and activity repetition types on vocabulary learning. In total, 78 South Korean fifth-grade students were divided into four conditions. Students in each condition were asked to read a passage with four of the eight target words (exposure: four times) and the other four words (exposure: once) for three days, and to perform the vocabulary activities assigned to each condition. According to the results, exposure frequency and activity repetition type had significant effects on vocabulary learning. Activity repetition type also had a significant interaction effect with exposure frequency and depth of processing. Notably, presenting a word 12 times (4x3) in reading intervals had a more positive impact on vocabulary learning than presenting it three times (1x3), particularly when different vocabulary activities were repeated. Meanwhile, when the same activity was repeated, an activity with a higher depth of processing was more effective for vocabulary learning.

As a result of this study, the performance evaluation of the development of laminated paper automatic adhesive processing machine is considered and concluded as follows. The cardboard processing unit for automatic folding and gluing designed a feeder for supplying cardboard, and the prototype production was compared with the existing production and the developed product, and the production rate was improved from 31,100 to 46,500 pieces per day, and the production speed was increased from 68 to 98. The defect rate was solved by solving the folding problem by comparing the existing production and the developed product, and the standard of the defect rate of the product was based on the folding, and the X1-X4 average defect rate was confirmed to be 0,000607%.

The consumption of enoki mushrooms has been associated with cases of listeriosis produced by Listeria monocytogenes, highlighting the significance of sanitizing food-contact surface, such as the velcro used in welding processing of enoki mushrooms, to ensure microbial safety. We investigated the inhibitory activity of nine chemical disinfectants at regular concentrations against L. monocytogenes isolated from a mushroom farm environment. The bacterial suspension was prepared in phosphate buffered saline and mushroom extract broth and inoculated onto the velcro surface. After inoculation, most disinfectants reduced the initial 8 log CFU/coupon concentration by less than 2 log CFU/coupon during a 5-min treatment. Slightly acidic hypochlorous water showed a reduction of approximately 4 log CFU/coupon when tested for more than 30 min at the maximum allowable concentration of 200 mg/L. Sodium hypochlorite solution showed a reduction of approximately 5 log CFU/coupon when used at 100 mg/L for 60 min. Peracetic acid, at the maximum allowable concentration of 300 mg/L, showed the most effective reduction of 5 log CFU/coupon or more when the surface was treated with 37.5 mg/L for 30 min. These results indicate that peracetic acid can be used as the disinfectant strategy to control cross-contamination of L. monocytogenes on the velcro surface of plastic wrappers used in the welding processing of enoki mushrooms.