The evolution of sinterability, microstructure and mechanical properties for the spark plasma sintered(SPS) Ti from commercial pure titanium(CP-Ti) was studied. The densification of titanium with 200 mesh and 400 mesh pass powder was achieved by SPS at under 10 MPa pressure and the flowing +Ar mixed gas atmosphere. The microstructure of Ti sintered up to consisted of equiaxed grains. In contrast, the growth of large elongated grains was shown in sintered bodies at with the 400 mesh pass powder and the lamella grains microstructure had been developed by increasing sintering temperature. The Vickers hardness of 240~270 HV and biaxial strength of 320~340 MPa were found for the specimen prepared at .

배 주요해충인 꼬마배나무이의 효과적인 방제를 위하여 배나무 단과지에 월동 성충이 이동시기인 2월 하순~3월 상순, 5월 중순 및 7월 상순에 기계유유제와 살 충제를 혼용하여 방제효과를 비교하였다. 월동성충 이동시기에 기계유유제와 살 충제 혼용살포는 혼합약종에 따라 다소의 차이가 있었으며 처리 7일후 살충율이 약 92~95.6%를 보였고, 살충제만 처리하였을 경우는 약 30~65%, 기계유유제만 살포한 경우는 살충제와 혼용하여 살포하는 것과 유사한 95.9%를 보였다. 5월 중 순과 7월 상순에 기계유제 200배와 디노테퓨란수화제 추천농도, 100배와 디노테 퓨란수화제 추천농도를 혼용 처리한 결과, 5월 중순 처리 10일후 기계유제 농도에 따라 각각 살충율이 93.8%, 95.0%를 보였고, 7월 상순에는 각각 90.6%, 80.8%를 보였다. 기계유제 200배, 100배를 5월 중순 살포시 처리 10일 후에 91.7%, 93.3%, 7월 상순에는 83.2%, 76.0%를 보여 7월 상순 방제 효과가 다소 낮았는데, 이는 꼬 마배나무이가 배설물인 감로에 덮여 생활하는 생태적 특성에 기인한 것으로 판단 된다. 더불어 배나무 잎이 있는 상태에서 기계유제 살포는 약해가 발생될 수 있고 광합성 효율에 영향을 미치기 때문에 추후 보다 정밀한 검토가 필요하다.

Early diagnoses of pregnancy for animal such as swine and bovine is extremely important to increase income of a farmhouse and for the management of farm. For the development of immunoasaay system of pregnancy in swine, we report a competitive heterologous enzyme linked immunosorbent assay (ELISA) for the direct measurement of oestrone sulfate (E1S) in diluted urine using anti-E1G (glucuronide) monoclonal antibody which cross react with E1S. The principle of assay was based on the typical solid-phase competitive ELISA methods using E1G-HRP (horseradish peroxidase) as a tracer and E1S for standard. The method had a reasonable sensitivity for the detection of E1S with 0.15 ng/ml as a detection limit. The intra-assay and inter-assay precisions were raging coefficient of from 8.50～9.67% and 8.50～9.87%, respectively, which were quite acceptable. In a field trial with a group 37 sows (18 non-pregnancy and 19 pregnancy sows) after day 29～30 post service, the concentration of E1S were determined to be below 30 ng/ml in all non-pregnancy group and over 48 ng/ml in pregnancy group except one sample. The method described here, heterologous ELISA for the measurement of E1S in urine is good enough for monitoring the early pregnancy test of swine.

Establishing a framework, to explain the path to safety accidents considering major safety management factors such as physical conditions including on-site activities and workplace, as well as human factors as to labor, supervisors, or managers, would be effective as the basis to control project's risks by preventing disasters. Therefore, this study aimed to clarify the mechanism in safety management and disaster occurrence. In order to accomplish the purpose, it identified and classified the factors related to accidents, reviewed the causal relationships among them, and suggested the influence diagram. The results of this research are expected to contribute to reinforcing the preventive management, and facilitating the development of integrated site control system based on safety risks.

본 연구는 경상남도의 중요한 연안습지를 대상으로 생태적 측면에서의 가치평가를 실시하여 연안습지의 무분별한 개발과 훼손을 최소화 하기 위한 기초자료를 제공하고자 수행하였다. 연안습지 평가를 위한 현지조사 결과, 저서생물은 통영시 용남면 동달리, 화삼리의 종수가 가장 많았고 거제시 거제면 외간리, 내간리 일대는 개체수와 생체량이 가장 많았다. 종다양성지수는 고성군 삼산면 미룡리가 가장 높게 나타났다. 염생식물의 표징종과 수반종이 가장 많이 출현한 지역은 마산시 진전면 이명리와 거제시 거제면 외간리, 내간리로 조사되었다. 이러한 현지조사 결과를 토대로 연안습지의 생태적 가치를 5개 등급으로 평가한 결과, 퇴적환경은 고성군 회화면 당항리, 고성군 삼산면 미룡리, 사천시 곤양면 구호리, 하동군 진교면 술상리, 남해군 이동면 석평리가 II등급으로 가장 높게 평가되었다. 저서생물은 마산시 진전면 이명리, 통영시 용남면 동달리, 거제시 거제면 외간리, 내간리가 II등급, 염생식물은 마산시 진전면 이명리와 거제시 거제면 외간리, 내간리가 II등급으로 가장 높게 평가되었다. 평가요인별 평균값을 기준으로 한 최종적인 평가등급은 마산시 진전면 이명리, 거제시 거제면 외간리, 내간리가 가장 높은 II등급으로 나타났고 남해군 이동면 석평리가 IV등급으로 가장 낮았다. 향후 연안습지 생태계의 지속적인 조사와 장기적인 모니터링, 그리 연안습지를 체계적으로 관리하기 위한 GIS기반 연안습지정보시스템 구축을 위한 연구가 필요할 것으로 사료된다.

Silicon quantum dots (Si QDs) in a superlattice for high efficiency tandem solar cells were fabricated by magnetron rf sputtering and their characteristics were investigated. SiC/Si1-xCx superlattices were deposited by co-sputtering of Si and C targets and annealed at 1000˚C for 20 minutes in a nitrogen atmosphere. The Si QDs in Si-rich layers were verified by transmission electron microscopy (TEM) and X-ray diffraction. The size of the QDs was observed to be 3-6 nm through high resolution TEM. Some crystal Si and -SiC peaks were clearly observed in the grazing incident X-ray diffractogram. Raman spectroscopy in the annealed sample showed a sharp peak at 516 cm-1 which is an indication of Si QDs. Based on the Raman shift the size of the QD was estimated to be 4-6 nm. The volume fraction of Si crystals was calculated to be about 33%. The change of the FT-IR absorption spectrum from a Gaussian shape to a Lorentzian shape also confirmed the phase transition from an amorphous phase before annealing to a crystalline phase after annealing. The optical absorption coefficient also decreased, but the optical band gap increased from 1.5 eV to 2.1 eV after annealing. Therefore, it is expected that the optical energy gap of the QDs can be controlled with growth and annealing conditions.

This study investigated the efficiency of mating disrupters for the control of Grapholita molesta(Busck) and Adoxophyes orana in pear orchards. G. molesta was shown 4 peak occurrence, which were different according to treatments. In conventional control, many moths were captured in mid and late April and peaks occurred in mid June, August, and early-mid September. In the non-control treatment, there were low populations in April. A. orana also appeared to 4 peak in 2007. Moths were rarely captured in mating disrupter treatment but many were captured in both the non-control and in conventional treatment. A. orana damage differed significantly between mating disrupter use and conventional control in 2006. Especially, the difference was significant between conventional control and mating disrupter to leaf damage in August, and there were similar results in the damage by G. molesta in the shoots and fruits.

이 연구는 고품질 귀리 사일리지의 제조를 위한 수확시기별 적정 예건시간을 도출하고자 수행하였다. 시험은 국내 육성품종인 삼한귀리를 가을에 파종하고 이듬해 봄인 출수 후 20일 부터 10일 간격으로 3회에 걸쳐 수확하여 각 수확시기별로 0, 4, 8, 32시간동안 예건을 실시하였으며, 각 예건시간별 식물체의 수분변화와 사일리지 제조 후 품질을 분석하였다. 그 결과 귀리는 출수 후 20일 정도에 수확할 경우 4시간 정도 포장예건을 하고, 출수 후 30일 정

In this study, genotyping was executed by using 11 microsatellite markers (BM1824, BM2113, ETH10, ETH225, ETH3, INRA23, SPS115, TGLA122, TGLA227, TGLA53, and TGLA126) for diversity of 214 Hanwoo cows in Hoengseong area. Each marker's size and number of allele, observed heterozygosity, expected total heterozygosity, and polymorphism information content were analyzed by 11 Microsatellite marker. The average of size range was detected from 150.9 to 174.9 in Hanwoo cows of Hoengseong. The number of average allele was 10.0 that is similar to the average of Kangwon Hanwoo, which is known as 10.5 in the previous report. The average were 0.751 for observed heterozygosity, 0.760 for expected total heterozygosity, 0.725 for polymorphism information content, respectively. These results were similar to previous studies in Kangwon Hanwoo, National Hanwoo and Korean Proven Bulls. This study is expected to contribute for genetic improvement of Hanwoo cows in Hoengseong as a popular brand.

배 병해충 방제시 농약사용 절감과 방제효율 개선을 위해 고속살포기(SS기; Speed Sprayer; HA-1000SCA)를 사용하여 2개 시험포장을 대상으로 각 포장에 동일한 시험구로 관행구(노즐:ø1.0mm 표준노즐; 분무압력 : 20kg/cm2; 표준농도; 살포량 : 1L/3.3m2), 관행저물량구(노즐:ø1.0mm 표준노즐; 분무압력 : 20kg/cm2; 표준농도; 살포량 : 0.7L/3.3m2), 저물량-1구(노즐:ID노즐(Lechler사; 스위스); 분무압력 : 10kg/cm2; 1.5배 고농도; 살포량 : 0.5L/3.3m2), 및 저물량-2구(노즐:ID노즐 (Lechler사; 스위스); 분무압력 : 10kg/cm2; 1.5배 고농도; 살포량 : 0.7L/3.3m2)로 설정하여 방제하였는데, 시험포장에 따라 병해충의 발생 정도는 달랐지만 배 생육기 동안 검은별무늬병, 붉은별무늬병, 꼬마배나무이, 사과애모무늬잎말이나방의 방제 효과는 관행구와 저물량-2구에서 적은 병해충 발생량을 보였다. 관행저물량구와 저물량-1구의 병해충 발생량의 전자의 두 처리구보다 많은 경향을 보였다. 수확과실에 대해 검은별무늬병과 붉은별무늬병의 피해과율은 재배기와 유사한 경향을 보였지만 복숭아순나방 등 심식충류와 사과애모무늬잎말이나방의 피해과율은 처리구간 큰 차이가 없었고, 시포험포장 I과 II의 관행저물량구에서 깍지벌레류에 의한 피해과율이 각각 2.1과 7.5%로 가장 많았고, 다른 처리구에서는 0.9~1.4%의 피해과율로 큰 차이가 없었다. 따라서, 단위면적당 농약사용량(A.I.)은 일정하게 유지하여야 할 것으로 생각된다.

Since it was developed by Joseph Aspdin, cement has been a common construction materials up to the present time.However, there are trace constituents in cement clinker. One of the trace constituents included in cement clinker, chromium,has become prominent and highly noticed lately as a social issue both inside and outside of this country because it affects thehuman body negatively. The aim of the present study was to investigate the concentration of water-soluble hexavalent chromiumin cement clinker by using industrial by-products. For that reason, raw materials were prepared to add different SiO2 , Al2O3,and Fe2O3 sources. After the raw materials such as the limestone, the sand and the clay, iron ore was pulverized and mixed,and the raw meal was burnt at about 1450oC in a furnace with an oxidizing atmosphere. The part in the raw materials of theclinker was substituted with slag, sludge, etc. and this was used to manufacturing cement clinker. To investigate the water-soluble hexavalent chromium content in clinker, raw meal was prepared by changing the modulus, the type, and the contentof clinker materials and tested concentrations of hexavalent chromium in the clinkers. To determine Cr+6 formation of theclinker, tests were done with raw meals adding chromium by using different industrial by-products. Consequently because thechromium was to be included in the raw materials of the clinker, production of Portland cement clinker was included with thechromium. Also, the chromium was converted into hexavalent chromium in the burning process.

본 논문에서는 물질의 원소 분석법 가운데 하나인 레이저 유도 플라즈마 분광법을 이용한 해양 환경 오염을 감시 기술의 적용 가능성 을 제시한다. 제주도 근해에서 채취한 백화시료에 포함되어 있는 칼슘 원소와 수돗물에 포함되어 있는 소듐, 칼슘 원소들을 레이저 유도 플라즈 마 분광법을 통해서 검출하였다. 또한 해수에 용해되어 있는 다양한 무기 원소들을 레이저 유도 플라즈마 분광법을 통해서 정량적으로 측정하 고자 할 때 사용할 수 있는 새로운 정량화 기법을 제안한다.

The current study examined Ag migration from the Ag paste bump in the SABiT technology-applied PCB. A series of experiments were performed to measure the existence/non-existence of Ag in the insulating prepreg region. The average grain size of Ag paste was 30 nm according to X-ray diffraction (XRD) measurement. Conventional XRD showed limitations in finding a small amount of Ag in the prepreg region. The surface morphology and cross section view in the Cu line-Ag paste bump-Cu line structure were observed using a field emission scanning electron microscope (FE-SEM). The amount of Ag as a function of distance from the edge of Ag paste bump was obtained by FE-SEM with energy dispersive spectroscopy (EDS). We used an electron probe micro analyzer (EPMA) to improve the detecting resolution of Ag content and achieved the Ag distribution function as a function of the distance from the edge of the Ag paste bump. The same method with EPMA was applied for Cu filled via instead of Ag paste bump. We compared the distribution function of Ag and Cu, obtained from EPMA, and concluded that there was no considerable Ag migration effect for the SABiT technology-applied printed circuit board (PCB).