낙동강 하구 기수생태 복원이 본격으로 논의가 진행 전인 2016년까지는 하류 수위의 예측을 위해 하구에서 수km 떨어진 기존 조위관측소(부산 및 가덕도)의 측정 자료를 활용하여 분석을 수행하였지만, 조위와 위상 차이로 인해 예측이 용이하지 않았다. 따라서, 낙 동강 하굿둑 인접 외해역에서 조석 영향을 받는 수위관측치를 이용하여 조석조화분해를 통한 정밀한 조위 예측 산정의 필요성이 대두되 어 본 연구를 수행하였다. 연구의 방법으로는 낙동강하굿둑 인근 외해역에서 10분 간격으로 기간별 관측자료의 저장상태 및 이상자료 유 무를 확인하고, 조석조화분해 프로그램인 TASK2000(Tidal Analysis Software Kit) Package를 이용하여 관측조위와 예측조위를 1대 1 비교하여 회귀상관분석을 수행하였다. 분석 결과, 관측조위와 예측조위간의 상관도는 0.9334로 높게 나타났으며, 당해 연도의 조위예측 분석시 직전 연도의 1년 조석관측 자료를 조화분해하여 산출된 조화상수를 이용하여 조위예측을 실시하면 보다 정확한 결과를 산출할 수 있음을 확인 하였다. 이를 바탕으로 2022년 예측조위를 생성하여 낙동강 하구 기수생태 복원의 해수유입량의 산정에 활용 중이다.

We report the synthesis and gas sensing properties of bare and ZnO decorated TeO2 nanowires (NWs). A catalyst assisted-vapor-liquid-solid (VLS) growth method was used to synthesize TeO2 NWs and ZnO decoration was performed using an Au-catalyst assisted-VLS growth method followed by a subsequent heat treatment. Structural and morphological analyses using X-ray diffraction (XRD) and scanning/transmission electron microscopies, respectively, demonstrated the formation of bare and ZnO decorated TeO2 NWs with desired phase and morphology. NO2 gas sensing studies were performed at different temperatures ranging from 50 to 400 oC towards 50 ppm NO2 gas. The results obtained showed that both sensors had their best optimal sensing temperature at 350 oC, while ZnO decorated TeO2 NWs sensor showed much better sensitivity towards NO2 relative to a bare TeO2 NWs gas sensor. The reason for the enhanced sensing performance of the ZnO decorated TeO2 NWs sensor was attributed to the formation of ZnO (n)/ TeO2 (p) heterojunctions and the high intrinsic gas sensing properties of ZnO.

To investigate the functional activity of different citrus fruit peels, antioxidant compounds in 70% ethanol extracts of mandarin, lemon, orange, and grapefruit peel powders were identified, and antioxidant and antibacterial activities were quantitated. Mandarin peel contained the highest content of total phenolic compounds and total flavonoid substances (21.46±0.12 mg GAE/g and 11.57±0.05 mg RE/g, respectively). The total phenolic compound content of the three other citrus fruits was 14.16±0.18-18.44±0.07, and their total flavonoid content was 5.51±0.10-7.46±0.09 mg RE/g. DPPH radical scavenging activity was the highest in lemon peel (87.64±0.21%), and mandarin peel displayed the best antioxidant activity with respective ABTS radical scavenging activity and FRAP measurements of 43.20±0.61% and 78.82±1.06 mM TE/g. Grapefruit peel antimicrobial activity increased with treatment time, and was the most potent among the four tested citrus species, inhibiting Staphylococcus aureus by about 4.05 log cycle. These findings demonstrate that mandarin and grapefruit peel can be used to prevent oxidation, improve food storage capabilities, and potentially preserve food quality.

역전기투석(reverse electrodialysis, RED)은 이온교환막을 격막으로 이용하여 해수와 담수의 농도차로부터 발전하 는 유망한 친환경 재생에너지 기술 중 하나이다. 이온교환막은 RED의 성능을 좌우하는 핵심 구성요소로 낮은 전기적 저항, 높은 이온선택투과도, 우수한 내구성 및 저렴한 제조 비용 등의 요구조건을 만족시켜야 한다. 본 연구에서는 다양한 두께 및 기공율을 갖는 다공성 고분자 지지체를 이용하여 세공충진 음이온교환막을 제조하고 이온교환 고분자의 조성과 막 두께가 RED의 발전 성능에 미치는 영향을 조사하였다. 이온교환막의 전기적 저항이 충분히 낮은 경우 RED 발전 성능은 주로 막의 apparent permselectivity에 의해 좌우됨을 확인할 수 있었다. 또한 막의 apparent permselectivity는 IEC, 가교도, 막 두께, 표면 개질 등을 통해 향상시킬 수 있으며 전기적 저항과의 trade off 관계를 고려하여 최적 조건을 찾아야 함을 확인하였다.

PURPOSES : Currently, the domestic construction industry is dominated by large-scale projects such as roads, ports, airports, and buildings. Construction on such projects is generally conducted simultaneously, but the process and quality management are led by a small number of responsible managers. In the case of road pavements, owing to rapid industrial development, economic growth, and the expansion of social overhead capital investment in the road construction industry, highways and general national roads have been constructed on a large scale. Therefore, this study aimed to improve and develop domestic concrete production and construction quality management by improving the reliability and transparency of production quality management and simplifying business processes. This was accomplished through the development of an Internet of Things (IoT)-based cement quality management system capable of automated design and build (D/B) construction and real-time monitoring. METHODS : The "IQ" system is a quality management system for enabling real-time monitoring of D/B quality at the time of concrete production and according to the designated age by utilizing quality test equipment developed with an LTE-Bluetooth function. It is possible to immediately identify and respond to quality problems through real-time monitoring, secure a reliable quality D/B because the quality test results cannot be arbitrarily manipulated, and to simplify the work process through the automatic D/B construction. In addition, improved quality control can be achieved through real-time information sharing and feedback system operations between contractors, managers, and personnel involved in construction. The quality control test items for developing the IQ system are the compression and flexural strengths, as these can be used to determine the design standard strength of pre-curing concretes (such as their slump and unit quantity) and the adequacy of the workability and durability, as well as the air volume to predict the durability, and the chloride content in the sections where reinforcement is used. CONCLUSIONS : This study identified difficulties and limitations in quality management according to the operation method in the domestic quality management systems, and in the real-time monitoring between managers and contractors. Thus, it was necessary to establish an improved systematic and reliable quality management system. The IQ system was developed to solve this problem.

PURPOSES : The increasing heat wave warnings during the summer season in Korea have significant impacts on daily life and industry as a whole, especially in urban areas (such as areas with asphalt and sidewalk pavements). Heat waves directly affect urban heat island and heat dome phenomena. Various urban temperature reduction measures are being discussed to reduce urban heat islands and heat dome phenomena and to improve citizen safety against summer heat waves; suggestions include thermal packaging, rooftop greening, and expansion of vegetation areas. There is a lack of analysis on the methodology for increasing the road spraying effect during summer heat waves (e.g., there is no systematic engineering study on the effect from reducing the temperature of the road spraying during a heat wave in the city) and on the types of road pavements in the city. In addition, as the asphalt pavements of roadways and block pavements installed in sidewalks account for a considerable portion of all pavements, this study provides a more systematic and scientific approach and procedures for reducing temperatures through road spraying in the city by tracking the effects of heat waves. METHODS : In this preliminary experiment, four types of road pavement materials were selected as test specimens: asphalt test specimens (AP- 300 mm × 300 mm × 50 mm), concrete test specimens (CP-300 mm × 300 mm × 50 mm), impermeable blocks (IB-200 mm × 200 mm × 60 mm), and self-permeable blocks (PB-200 mm × 200 mm × 60 mm). As a test method to evaluate the size and duration of each spray effect package type, the surface temperature of each specimen was measured using thermal imaging cameras every 20 min after spraying at the maximum temperature point of each specimen, and the average surface temperature was analyzed based on the collected temperature data. In addition, to conduct a quantitative analysis of the effect of reducing the surface temperature of road pavements by road spraying in summer, field tests were conducted on asphalt roads and watertight blocks for sidewalks. RESULTS : As a result of the comparative analysis of the spray effect under a 36 ℃ air temperature based on a heat wave warning, the surface temperatures were, from high to low, the asphalt (68.8 ℃), concrete (59.1 ℃), impermeable block (57.3 ℃), and permeable block (58.7 ℃). The asphalt pavement had the greatest effect on the heat island and heat dome phenomena. From measuring the temperature reduction effect and sustainability of each type of road pavement, the surface temperature reduction effects were ranked in the following order: water-permeable block (Δ18.0 ℃), asphalt test piece (Δ17.5 ℃), concrete test piece (Δ12.2 ℃), and water-permeable block (over 240 min). In the report pitching block, the average road surface temperature reduction between the pore recovery and treatment was expected to continue to decrease by approximately -4.3 ℃ on the day of work and approximately -2.4 ℃ on the next day. The expected effect of the temperature reduction owing to simple spraying on the surface of the pore block was evaluated to be limited to the day. CONCLUSIONS : In the road spray effect analysis conducted on the common asphalt road, there was a slight difference in the initial temperature reduction size as the test specimen was measured, but the surface temperature difference between the non-spray section and spray section tended to be approximately Δ3°C after 140 minutes of spraying. Therefore, it was determined that the asphalt pavement temperature reduction plan through road spraying in urban areas in summer would be the most effective if it was repeated twice or more in an hour (between 13:00 and 14:00) on the day of the heat wave.

In terms of habitat conservation, it is essential to develop a habitat assessment system that can evaluate not only the suitability of the current habitat, but also the health and stability of the habitat. This study aimed to develop a methodology of habitat quality assessment for endangered species by analyzing various existing habitat assessment methods. The habitat quality assessment consisted of selecting targeted species, planning of assessment, selecting targeted sites, assessing performance, calculating grade, and expert verification. Target sites were selected separately from core and potential habitats using a species distribution model or habitat suitability index. Habitat assessment factors were classified into ecological characteristic, landscape characteristic, and species-habitat characteristic. Ecological characteristic consisted of thirteen factors related to health of tree, vegetation, and soil. Landscape characteristic consisted of five factors related to fragment and connectivity of habitat. Species-habitat characteristic consisted of factors for evaluating habitat suitability depending on target species. Since meanings are different depending on characteristics, habitat quality assessment of this study could be used by classifying results for each characteristic according to various assessment purposes, such as designation of alternative habitats, assessment of restoration project, and protected area valuation for endangered species. Forest habitat quality assessment is expected to play an important role in conservation acts of endangered species in the future through continuous supplementation of this system in regard to quantitative assessment criteria and weighting for each factor with an influence.

Bio-based alternative leathers may be produced from biomass fiber, protein polymers, bacterial cellulose, and mushroom mycelia. Of these components, mushroom mycelia are of greatest interest. In this study, the potential of Fomes fomentariusas a mushroom mycelial mat was confirmed, and the optimal strain for the development of the mycelial mat was determined. Moreover, the quality of the mycelial mat was improved by identifying an efficient culture method to increase productivity. Mutant strains whose independence was verified were obtained by treatment with gamma irradiation under various conditions. Biofilm formation by the resulting strains was examined in sawdust and liquid media and the characteristics of the biofilms were analyzed. The biofilm of the mutant strains showed results that were similar to or better than the biofilms of longevity and cypress mushrooms. These findings are expected to be utilized in future research aimed at discovering new biomaterials using mushroom mycelia.

반추위 미생물체 단백질의 아미노산 조성이 한우의 에 너지원 사료에 따라 차이가 있는지를 조사하고자 본 연구 가 수행되었다. 본 실험은 국내 한우 비육우 사육에 주로 이용되는 에너지원 사료인 옥수수(T1), 생미강(T2), 소맥 (T3), 소맥피(T4)를 이용하여 in vitro 반추위 발효실험을 진행하여 발효 24시간 후 배양액의 발효 성상, 미생물체 단백질 합성량(MPS), 미생물의 아미노산 조성 및 미생물 균총 변화를 분석하였다. 배양액의 pH는 T4가 6.02로 다 른 처리구들에 비해서 가장 높았으며, T1은 4.84로 가장 낮았다(p<0.05). Total VFA 농도는 T2가 96.80mM로 다른 처리구들에 비해서 가장 높았고, T1이 53.35mM로 가장 낮았다(p<0.05). 미생물체 단백질 합성량은 T3가 222.50g/L로 다른 처리구들에 비해서 높았으며(p<0.05), T1과 T4는 유의적인 차이는 없었지만 T1이 가장 낮았다. DGGE band 분석결과 모든 처리구는 57.5% 이하의 유사도를 나타내었으며, 급여되는 사료에 따라서 미생물 군집 이 다르게 나타났다. 미생물 내 총 아미노산 함량은 T3와 T4가 다른 처리구보다 높았다(p<0.05). 미생물의 아미노산 조성 중 대부분의 필수 아미노산은 T4가 다른 처리구들에 비해서 낮았다. 하지만 methionine은 다른 필수 아미노산 과 다르게 T4에서 가장 높았다(p<0.05). 곡류 사료 위주의 급여 시 결핍되기 쉬운 lysine은 모든 처리구에서 미생물 의 아미노산 조성이 8.05~8.98%의 범위에 있었다. 따라서, 본 연구에서 반추 가축 급여 에너지 사료원에 따른 반추 위 내 미생물 발효특성과 미생물 군집의 차이가 미생물의 아미노산 조성을 변화시킨다는 것을 확인하였다.

양식장 환경관리를 위하여 여러 나라에서 양식장 환경관리시스템을 구축하고 있으며, 어장환경평가가 그중 하나이다. 2013년에 개정된 국내 어장관리법에는 어류가두리양식장 면허를 연장할 때 어장환경평가를 받도록 명시되어 있다. 어장환경평가는 과학적 분석을 통한 평가를 바탕으로 양식장 환경 개선 조치를 실행하여, 지속 가능한 어업생산 조성, 어장 생산력 증가, 어업인의 소득 증가를 목적으로 한다. 어장환경평가의 평가지표는 저서다모류 군집을 기초로 한 생물지수인 저서동물지수(BHI)와 총유기탄소량(TOC)이며, 두 항목을 점 수화하여 단일등급으로 산출하여 평가에 사용한다. 본 연구는 어장환경평가지표인 BHI와 TOC의 선정 과정과 산출된 평가 등급의 생태학 적 의미를 설명한다.

본 논문은 남해안 자란만 패류양식어장에서 약 2년 동안 월별로 기초생산력, Chl. a, 영양염류, 입자유기물질과 퇴적물의 유기오 염 정도 및 생화학 조성 등 주요 양식생물의 서식환경인자의 변동특성과 상관성 등을 분석하였다. 또한, 다른 연안 어장과 기초생산력을 비교하고 어장환경관리와 관련된 정책방안을 제시하였다. 월별 평균 기초생산력은 6.43∼115.43 ㎎C m-2 hr-1 범위로 여름과 가을에 높았는 데, 가막만과 마산만 보다는 낮았고, 가로림만과 서해보다는 높았으며, 대체적으로 양식장이 많이 분포한 내만은 그 변동 폭이 상대적으 로 컸다. Chl. a를 구성하는 식물플랑크톤의 크기별 점유율이 시기별로 다소 차이가 있었고, 영양염의 고갈로 인한 식물플랑크톤의 생산력 제한은 거의 없었으나, 대부분 시기에 N/P비가 16 이하로 질소가 상대적으로 부족한 것으로 판단되었다. 수층 입자유기물질의 생화학적 조성은 탄수화물이 가장 높았으나, 반면 표층 퇴적물에서는 지질과 단백질 함량이 높았다. 퇴적물의 TOC와 AVS 농도는 만 안쪽에서 높 았고 일부 시기에는 어장환경기준을 초과한 상태였으며, C:N 비는 평균 8.1∼10.4 범위로 나타났다. 기초생산력은 Chl. a와의 상관성이 가 장 높았고, 입자물질성분 중에서는 탄소보다는 질소 및 단백질과의 상관성이 높았다. 최근 5년 동안의 수층에서의 Chl. a, DIN, DIP 농도는 감소하는 경향이었지만, 반대로 퇴적물의 오염도는 증가하는 추세였다. 자란만의 연간 기초생산력 125.9 gC m-2 yr-1, 굴 양식장 면적 4.97 ㎞2 를 고려하면 연간 식물플랑크톤으로부터 생산되는 탄소량이 약 625 ton이며, 연간 굴 생산 습중량은 약 6,250 ton으로 추정되었다.

무삼투압차 역삼투압(Δπ= 0)은 KAIST H. N. Chang 명예교수가 2013년 발명, 2014년 미국 특허 출원, 2018년 특 허 취득(US 9,950,297) 해수담수화기술. Chang 등의 RO 기술은 삼투압 조정조와 저압 역삼투압의 2 챔버로 구성. Chang 등은 소금물을 비롯한 모든 수용액은 물과 용질(소금)로 완전 분리 가능 주장. 삼투압차 조정조, 저압 역삼투압조 2 챔버로 구성됨. 고농도 용액의 삼투압은 1908년 미국화학회지 출간된 MIT G. N. Lewis식 이용. 두 번째 특허(US 10,953,3367)에서 RO가 10~12 bar 저 삼투압차 수행 가능 증명. 세 번째 특허(Korea 10-2322755, 해외 출원 중) Singularity ZERO 활용하면 기존 RO 에 비해 물은 50% 추가, 막 면적은 1/3, 이론에너지는 1/5, 동일 용량의 S-ZERO 기술은 기존 RO 건설비의 50~60%로 예측됨.