During a month, wave observation was characteristic of Suyuong bay since 16th of July. During the period, typhoons which were "Ma-on, Muifa" landed on Suyong bay. Observation point places a half-way point between Gwangan light beacon in the utmost bounds of the west and Haeundae floating buoy in east. The observation point was selected for confirming the relations of river discharge and storm surge of suyong bay. To investigate the characteristic, using meteorological data not in just Gwangan light beacon but in Haeundae floating buoy. As a result, at Gwangan light beacon the maximum significant wave observed was 3.5 m and period was 10,3 sec, at the Observation point each outcomes were 3.8 m and 10.1 sec, Haeundae floating had 2 m and 8.5 sec as consequences. The height of observation point was higher than Haeundae's or Gwangan’s and had two peaks. Although the wave direction in observation point came from southern east, being irregular in Haeundae floating buoy. Up to now, the interrelationship of weather conditions and wave characteristics have been verified, the characteristic of wave distribution

아보카도(Avocado; Persea americana)는 현재 재배되는 다른 열대과수들과 달리 무가온재배 가능하고, 과실의 기능적 특성이 우수하고 국내 소비자 기호 알맞은 작물이다. 2010년 재배면적이 0.2ha였지만, 열대과수 중에서 망고 다음으로 재배가 유망한 작물이다. 2011년에 3곳의 아보카도 재배원에서 해충 조사결과, 아보카도에 발생하여 피해를 주는 종은 총 6종류가 조사되였다. 나방류 해충은 줄고운가지나방(Ectropis excellens)과 차잎말이나방(Homona magnanima)이 다량 발생하였고, 피해는 잎과 과실에 모두 나타났다. 잎만 가해하는 해충으로는 명주달팽이(Acusta despecta), 진딧물, 볼록총채벌레(Scirtothrips dosalis), 온실가루이(Trialeurodes vaporariorum)이었다. 달팽이 잎 피해는 과원 전체적으로 연중 발생하였고, 진딧물은 신엽에서만 주로 발생하였다. 볼록총채벌레과 온실가루이 유충은 주로 일부 신엽에서 발견되었다. 이외에 가루깍지벌레 종류가 줄기에서 소량 발생하였으나 피해는 거의 없었다.

The CdS thin film used as a window layer in the CdTe thin film solar cell transports photo-generated electrons to the front contact and forms a p-n junction with the CdTe layer. This is why the electrical, optical, and surface properties of the CdS thin film influence the efficiency of the CdTe thin film solar cell. When CdTe thin film solar cells are fabricated, a heat treatment is done to improve the qualities of the CdS thin films. Of the many types of heat treatments, the CdCl2 heat treatment is most widely used because the grain size in CdS thin films increases and interdiffusion between the CdS and the CdTe layer is prevented by the heat treatment. To investigate the changes in the electrical, optical, and surface properties and the crystallinity of the CdS thin films due to heat treatment, CdS thin films were deposited on FTO/glass substrates by the rf magnetron sputtering technique, and then a CdCl2 heat treatment was carried out. After the CdCl2 heat treatment, the clustershaped grains in the CdS thin film increased in size and their boundaries became faint. XRD results show that the crystallinity improved and the crystalline size increased from 15 to 42 nm. The resistivity of the CdS single layer decreased from 3.87 to 0.26 Ωcm, and the transmittance in the visible region increased from 64% to 74%.

Transparent conducting oxides (TCOs) used in the antireflection layer and current spreading layer of heterojunction solar cells should have excellent optical and electrical properties. Furthermore, TCOs need a high work function over 5.2 eV to prevent the effect of emitter band-bending caused by the difference in work function between emitter and TCOs. Sn-doped In2O3 (ITO) film is a highly promising material as a TCO due to its excellent optical and electrical properties. However, ITO films have a low work function of about 4.8 eV. This low work function of ITO films leads to deterioration of the conversion efficiency of solar cells. In this work, ITO films with various Zn contents of 0, 6.9, 12.7, 28.8, and 36.6 at.% were fabricated by a co-sputtering method using ITO and AZO targets at room temperature. The optical and electrical properties of Zn-doped ITO thin films were analyzed. Then, silicon heterojunction solar cells with these films were fabricated. The 12.7 at% Zn-doped ITO films show the highest hall mobility of 35.71 cm2/Vsec. With increasing Zn content over 12.7, the hall mobility decreases. Although a small addition of Zn content increased the work function, further addition of Zn content over 12.7 at.% led to decreasing electrical properties because of the decrease in the carrier concentration and hall mobility. Silicon heterojunction solar cells with 12.7 at% Zn-doped ITO thin films showed the highest conversion efficiency of 15.8%.

This study was conducted to evaluate Geometridae (Lepidoptera) species as pests and the damage they cause in citrus orchards in Jej u, Korea. Seven geometridae species occurred in citrus orchards: Ascotis selenaria, Ectropis excellens, Menophra senilis, Biston panterinaria, Ourapteryx nivea, Odontopera arida and Hypomecis punctinalis. Among them, A. selenaria was most abundant, followed by E. excellens and M senilis. Most Geometridae larvae fed on citrus leaves, but A. selenaria larvae ate fruits and leaves. Fruit damage of Citrus unshiu appeared as gnawed scars caused by young larvae feeding on fruit surface. Fruit damage on Shiranui fruits appeared as a wide hole or deep scars caused by feeding by mature larvae (6th instar). Citrus leaves damage due to Geometridae larvae was high during May to June. Fruit damage started in late June as the spring-shoots of citrus hardened and increased sharply in late July. In the field experiment, fruit damage in the late season reached 4.2% in both 2008 and 2009 and reached 5.2% in 2010. In citrus orchards, A. selenaria larvae started to appear in mid-May and their populations peaked in mid June, late July, and early to mid-September. Adult males of A. selenaria had a maximum peak in mid-May, and two other peaks in early to late July and late August to early September. A. selenaria male adults were collected in a pheromone traps constantly throughout Jeju Island.

In this study, we inserted a Zn buffer layer into a AZO/p-type a-si:H layer interface in order to lower the contact resistance of the interface. For the Zn layer, the deposition was conducted at 5 nm, 7 nm and 10 nm using the rf-magnetron sputtering method. The results were compared to that of the AZO film to discuss the possibility of the Zn layer being used as a transparent conductive oxide thin film for application in the silicon heterojunction solar cell. We used the rf-magnetron sputtering method to fabricate Al 2 wt.% of Al-doped ZnO (AZO) film as a transparent conductive oxide (TCO). We analyzed the electro-optical properties of the ZnO as well as the interface properties of the AZO/p-type a-Si:H layer. After inserting a buffer layer into the AZO/p-type a-Si:H layers to enhance the interface properties, we measured the contact resistance of the layers using a CTLM (circular transmission line model) pattern, the depth profile of the layers using AES (auger electron spectroscopy), and the changes in the properties of the AZO thin film through heat treatment. We investigated the effects of the interface properties of the AZO/p-type a-Si:H layer on the characteristics of silicon heterojunction solar cells and the way to improve the interface properties. When depositing AZO thin film on a-Si layer, oxygen atoms are diffused from the AZO thin film towards the a-Si layer. Thus, the characteristics of the solar cells deteriorate due to the created oxide film. While a diffusion of Zn occurs toward the a-Si in the case of AZO used as TCO, the diffusion of In occurs toward a-Si in the case of ITO used as TCO.

To reduce manufacturing costs of crystalline silicon solar cells, silicon wafers have become thinner. In relation to this, the properties of the aluminium-back surface field (Al-BSF) are considered an important factor in solar cell performance. Generally, screen-printing and a rapid thermal process (RTP) are utilized together to form the Al-BSF. This study evaluates Al-BSF formation on a (111) textured back surface compared with a (100) flat back surface with variation of ramp up rates from 18 to 89˚C/s for the RTP annealing conditions. To make different back surface morphologies, one side texturing using a silicon nitride film and double side texturing were carried out. After aluminium screen-printing, Al-BSF formed according to the RTP annealing conditions. A metal etching process in hydrochloric acid solution was carried out to assess the quality of Al-BSF. Saturation currents were calculated by using quasi-steady-state photoconductance. The surface morphologies observed by scanning electron microscopy and a non-contacting optical profiler. Also, sheet resistances and bulk carrier concentration were measured by a 4-point probe and hall measurement system. From the results, a faster ramp up during Al-BSF formation yielded better quality than a slower ramp up process due to temperature uniformity of silicon and the aluminium surface. Also, in the Al-BSF formation process, the (111) textured back surface is significantly affected by the ramp up rates compared with the (100) flat back surface.

제주도에서 현재 망고(mango; Mangefera indica L. var. irwin), 용과(dragon fruit; Hylocereus undatus), 아떼모야(attemoya) 순으로 많이 재배되고 있다. 2008 년부터 2010년까지 제주도에 재배되는 망고에는 총 13종의 해충이 발생하는 것으 로 조사되었고, 이중 볼록총채벌레(Scirtothrips dosalis), 오이총채벌레(Thrips palmi), 차먼지응애(Polyphagotarsonemus latus), 담배거세미나방(Spodoptera litura), 차 애모무늬이말이나방(Adoxophyes spp.), 네눈쑥가지나방(Ascotis selenaria) 등 나 방류 해충의 발생과 피해가 많다. 특히, 볼록총채벌레는 2010년에 처음으로 망고 에 발생하여 피해를 주는 것으로 확인되었고, 잎 외에도 과실 표면을 가해하여 상 품성을 크게 낮추어 경제적 피해를 유발하였다. 용과에서는 개미(formicidae), 목 화진딧물(Aphis gossypii) 등 진딧물류, 담배거세미나방(Spodoptera litura), 달팽 이류의 발생과 피해가 많았다. 특히 용과 재배 전시기에 걸쳐 개미에 의한 줄기 및 과실 피해가 가장 심했다. 아떼모야의 경우 담배거세미나방(Spodoptera litura), 차잎말이나방(Homona magnanima), 진딧물류, 감귤바구미(Sympiezomias lewisi) 가 발생하였다.

Silicon heterojunction solar cells have been studied by many research groups. In this work, silicon heterojunction solar cells having a simple structure of Ag/ZnO:Al/n type a-Si:H/p type c-Si/Al were fabricated. Samples were fabricated to investigate the effect of transparent conductive oxide growth conditions on the interface between ZnO:Al layer and a-Si:H layer. One sample was deposited by ZnO:Al at low working pressure. The other sample was deposited by ZnO:Al at alternating high working pressure and low working pressure. Electrical properties and chemical properties were investigated by light I-V characteristics and AES method, respectively. The light I-V characteristics showed better efficiency on sample deposited by ZnO:Al by alternating high working pressure and low working pressure. Atomic concentrations and relative oxidation states of Si, O, and Zn were analyzed by AES method. For poor efficiency samples, Si was diffused into ZnO:Al layer and O was diffused at the interface of ZnO:Al and Si. Differentiated O KLL spectra, Zn LMM spectra, and Si KLL spectra were used for interface reaction and oxidation state. According to AES spectra, sample deposited by high working pressure was effective at reducing the interface reaction and the Si diffusion. Consequently, the efficiency was improved by suppressing the SiOx formation at the interface.

Effect of Cu content on microstructural and magnetic properties of a (wt.%), (x = 0.2, 0.3, 0.4, 0.5) strip-cast was studied. The average inter-lamellar spacing in the free surface and wheel side of the strip cast increased as the Cu content increases. The grain uniformity, the grain alignment, and (00L) texture of the strip cast increased with Cu contents up to 0.4 wt.%. These microstructural changes were attributed to the decrease of the effective cooling rate of the melted alloy caused by the decrease of the melting temperature of resulting from Cu addition. Coercivity and remanence were increased because of the grain alignment and (00L) texture improvement with Cu contents up to 0.4 wt.%.

We have studied methods to save Si source during the fabrication process of crystalline Si solar cells. One way is to use a thin silicon wafer substrate. As the thickness of the wafers is reduced, mechanical fractures of the substrate increase with the mechanical handling of the thin wafers. It is expected that the mechanical fractures lead to a dropping of yield in the solar cell process. In this study, the mechanical properties of 220-micrometer-solar grade Cz p-type monocrystalline Si wafers were investigated by varying saw-damage etching conditions in order to improve the flexural strength of ultra-thin monocrystalline Si solar cells. Potassium hydroxide (KOH) solution and tetramethyl ammonium hydroxide (TMAH) solution were used as etching solutions. Etching processes were operated with a varying of the ratio of KOH and TMAH solutions in different temperature conditions. After saw-damage etching, wafers were cleaned with a modified RCA cleaning method for ten minutes. Each sample was divided into 42 pieces using an automatic dicing saw machine. The surface morphologies were investigated by scanning electron microscopy and 3D optical microscopy. The thickness distribution was measured by micrometer. The strength distribution was measured with a 4-point-bending tester. As a result, TMAH solution at 90˚C showed the best performance for flexural strength.

Hexagonal barium ferrite () nano-particles have been successfully fabricated by spraypylorysis process. precursor solutions were synthesized by self-assembly method. Diethyleneamine (DEA) surfactant was used to fabricate the micelle structure of Ba-DEA complex under various DEA concentrations. powders were synthesized with addition of Fe ions to Ba-DEA complex and then fabricated powders by spray-pyrolysis process at the temperature range of . The molar ratio of Ba/DEA and heat-treatment temperatures significantly affected the magnetic properties and morphology of powders. powders synthesized with Ba/DEA molar ratio of 1 and heat-treated at showed the coercive forces (iHc) of 4.2 kOe with average crystal size of about 100 nm.

HDDR treated anisotropic Nd-Fe-B powders have been widely used for the sheet motors and the sunroof motors of hybrid or electric vehicles, due to their excellent magnetic properties. Microstructural alignment of HDDR treated powders are mostly depending on the hydrogen reaction in disproportionation step, so the specific method to control hydrogenation reaction is required for improving magnetic properties. In disproportionation step, hydrogenation pressure and reaction time were controlled in the range of 0.15~1.0 atm for 15~180 min in order to control the micorstructural alignment of phase and, at the same time, to improve remanence of HDDR treated magnet powders. In this study, we could obtain a well aligned anisotropic Nd-Fe-B-Ga-Nb alloy powder having high remanence of 12 kG by reducing hydrogen pressure down to 0.3 atm in disproportionation step.

Si nanowire/multiwalled carbon nanotube nanocomposite arrays were synthesized. Vertically aligned Si nanowire arrays were fabricated by Ag nanodendrite-assisted wet chemical etching of n-type wafers using HF/AgNO3 solution. The composite structure was synthesized by formation of a sheath of carbon multilayers on a Si nanowire template surface through a thermal CVD process under various conditions. The results of Raman spectroscopy, scanning electron microscopy, and high resolution transmission electron microcopy demonstrate that the obtained nanocomposite has a Si nanowire core/carbon nanotube shell structure. The remarkable feature of the proposed method is that the vertically aligned Si nanowire was encapsulated with a multiwalled carbon nanotube without metal catalysts, which is important for nanodevice fabrication. It can be expected that the introduction of Si nanowires into multiwalled carbon nanotubes may significantly alter their electronic and mechanical properties, and may even result in some unexpected material properties. The proposed method possesses great potential for fabricating other semiconductor/CNT nanocomposites.

Hexagonal barium ferrite () nano-particles have been successfully synthesised using selfassembly method. Diethyleneamine (DEA) surfactant was used to fabricate the micelle structure of Ba-DEA complex under various DEA concentrations. powders were synthesized with addition Fe ions to Ba-DEA complex and then heat treated at temperature range of 800-1000. The molar ratio of Ba/DEA and heat-treatment temperature significantly affected the magnetic properties and morphology of powders. powders synthesized with Ba/DEA molar ratio of 1 and heat-treated at 1000 for 1 hour showed the coercive forces (iHc) of 4.84 kOe with average crystal size of about 200 nm.

HDDR treated anisotropic Nd-Fe-B powders have been widely used, due to their excellent magnetic properties, especially for sheet motors and sunroof motors of hybrid and electric vehicles. Final microstructure and coercivity of such Nd-Fe-B powders depend on the state of starting mother alloys, so additional homogenization treatment is required for improving magnetic properties of them. In this study, a homogenization treatment was performed at in order to control the grain size and Nd-rich phase distribution, and at the same time to improve coercivity of the HDDR treated magnetic powders. FE-SEM was used for observing grain size of the HDDR treated powder and EPMA was employed to observe distribution of Nd-rich phase. Magnetic properties were analyzed with a vibrating sample magnetometer.

In this study we investigated the effect of the multi-step texturing process on the electrical and optical properties of hydrogenated Al-doped zinc oxide (HAZO) thin films deposited by rf magnetron sputtering. AZO films on glass were prepared by changing the H2/(Ar+H2) ratio at a low temperature of 150˚C. The prepared HAZO films showed lower resistivity and higher carrier concentration and mobility than those of non-hydrogenated AZO films. After deposition, the surface of the HAZO films was multi-step textured in diluted HCl (0.5%) for the investigation of the change in the optical properties and the surface morphology due to etching. As a result, the HAZO film fabricated under the type III condition showed excellent optical properties with a haze value of 52.3%.

The influence of various surface morphologies on the mechanical strength of silicon substrates was investigated in this study. The yield for the solar cell industry is mainly related to the fracturing of silicon wafers during the manufacturing process. The flexural strengths of silicon substrates were influenced by the density of the pyramids as well as by the size and the rounded surface of the pyramids. To characterize and optimize the relevant texturing process in terms of mechanical stability and the fabrication yield, the mechanical properties of textured silicon substrates were investigated to optimize the size and morphology of random pyramids. Several types of silicon substrates were studied, including the planar type, a textured surface with large and small pyramids, and a textured surface with rounded pyramids. The surface morphology and a cross-section of the as-textured and fractured silicon substrates were investigated by scanning electron microscopy.

Sintered Nd-Fe-B magnets have been widely used due to their excellent magnetic properties, especially for driving motors of hybrid and electric vehicles. The microstructure of Nd-Fe-B magnets strongly affects their magnetic properties, in particular the coercivity. Therefore, a post-sintering process like heat-treatment is required for improving the magnetic properties of Nd-Fe-B sintered magnets. In this study, cyclic heat treatment was performed at temperatures between and up to 16 cycles in order to control microstructures such as size and shape of the Nd-rich phase without grain growth of the phase. The 2 cycles specimen at this temperature range showed more homogeneous microstructure which leads to higher coercivity of 35 kOe than as-sintered one.