간행물
한국분말야금학회지 KCI 등재 Journal of Korean Powder Metallurgy Institute
- 발행기관 한국분말재료학회(구 한국분말야금학회)
- 자료유형 학술지
- 간기 격월간
- ISSN 1225-7591 (Print)2287-8173 (Online)
- 수록기간 1994 ~ 2024
- 주제분류 공학 > 금속공학 공학 분류의 다른 간행물
- 십진분류KDC 559DDC 629
권호리스트/논문검색
Vol. 17 No. 2 (2010년 4월) 11건
1.
2010.04
구독 인증기관 무료, 개인회원 유료
4,000원
2.
2010.04
구독 인증기관 무료, 개인회원 유료
4,500원
3.
2010.04
구독 인증기관 무료, 개인회원 유료
In this study, we successfully synthesized a nano-sized lanthanum-modified lead-titanate (PLT) powder with a perovskite structure using a high-energy mechanochemical process (MCP). In addition, the sintering behavior of synthesized PLT nanopowder was investigated and the sintering temperature that can make the full dense PLT specimen decreased to below by using powder as sintering agent. The pure PLT phase of perovskite structure was formed after MCP was conducted for 4 h and the average size of the particles was approximately 20 nm. After sintered at 1050 and , the relative density of PLT was about 93.84 and 95.78%, respectively. The density of PLT increased with adding and the specimen with the relative densitiy over 96% were fabricated below when 2 wt% of was added.
4,000원
4.
2010.04
구독 인증기관 무료, 개인회원 유료
Carbon-nanotube-embedded bismuth telluride (CNT/) matrix composites were fabricated by a powder metallurgy process. Composite powders, whereby 5 vol.% of functionalized CNTs were homogeneously mixed with alloying powders, were successfully synthesized by using high-energy ball milling process. The powders were consolidated into bulk CNT/ composites by spark plasma sintering process at for 10 min. The fabricated composites showed the uniform mixing and homogeneous dispersion of CNTs in the matrix. Seebeck coefficient of CNT/ composites reveals that the composite has n-type semiconducting characteristics with values ranging to with increasing temperature. Furthermore, the significant reduction in thermal conductivity has been clearly observed in the composites. The results showed that CNT addition to thermoelectric materials could be useful method to obtain high thermoelectric performance.
4,000원
5.
2010.04
구독 인증기관 무료, 개인회원 유료
Two kinds of oxide-dispersion-strengthened (ODS) 316L stainless steel were manufactured using a wet mixing process(wet) and a mechanical alloying method (MA). An MA 316L ODS was prepared by a mixing of metal powder and a mechanical alloying process. A wet 316L ODS was manufactured by a wet mixing with 316L stainless steel powder. A solution of yttrium nitrate was dried after being in the wet 316L ODS alloy. The results showed that carbon and oxygen were effectively reduced during the degassing process before the hydroisostatic process (HIP) in both alloys. It appeared that the effect of HIP treatment on increase in impact energy was pronounced in the MA 316L ODS alloy. The MA 316L ODS alloy showed a higher yield strength and a smaller elongation, when compared to the wet 316L ODS alloy. This seemed to be attributed to the enhancement of bonding between oxide and matrix particles from HIP and to the presence of a finer oxide of about 20 nm from the MA process in the MA 316L ODS alloy.
4,000원
6.
2010.04
구독 인증기관 무료, 개인회원 유료
The fabrication of interconnect from titanium powders and powders is investigated. Corrosion-resistant titanium and are used as reinforcement in order to reveal high heat and corrosion resistance at the elevated temperature. We fabricated the plates for interconnect reinforced with by mixing titanium powders with 10 wt.% of nano-sized . Spark Plasma Sintering (SPS) was chosen for the sintering of these composites. The plate made of titanium powders and powders demonstrates higher corrosion resistance than that of the plate of titanium powders alone. The physical properties of specimens were analyzed by performing hardness test and biaxial strength test. The electrochemical properties, such as corrosion resistance and hydrogen permeability at high temperature, were also investigated. The microstructures of the specimens were investigated by FESEM and profiles of chemical compositions were analyzed by EDX.
4,000원
7.
2010.04
구독 인증기관 무료, 개인회원 유료
Sm-16.7wt%Co alloy powders were prepared by high energy ball milling under the conditions of various milling time and the content of process control agent (PCA), and their microstructure and magnetic properties were investigated to establish optimum processing conditions. The initial powders employed showed irregular shape and had a size ranging from 5 to . After milling for 5 h, the shape of powders changed to round shape and their mean powder size was approximately , which consisted of the agglomerated nano-sized particles with 15 nm in diameter. The coercivity was reduced with increasing the milling time, whereas the saturation magnetization increased. As the content of PCA increased, the powder size minutely decreased to approximately at the PCA content of 10 wt%. The XRD patterns showed that the main diffraction peaks disappeared apparently after milling, indicating the formation of amorphous structure. The measured values of coercivity were almost unchanged with increasing the content of PCA.
4,000원
8.
2010.04
구독 인증기관 무료, 개인회원 유료
Bismuth-telluride based thermoelectric powders were fabricated by two-step planetary milling process which produces bimodal size distribution ranging . The powders were reduced in hydrogen atmosphere to minimize oxygen contents which cause degradation of thermoelectric performance by decreasing electrical conductivity. Oxygen contents were decreased from 0.48% to 0.25% by the reduction process. In this study, both the as-synthesized and the reduced powders were consolidated by the spark plasma sintering process at for 10 min at the heating rate of and then their thermoelectric properties were investigated. The sintered samples using the reduced p-type thermoelectric powders show 15% lower specific electrical resistivity () than those of the as-synthesized powders while Seebeck coefficient and thermal conductivity do not change a lot. The results confirmed that ZT value of thermoelectric performance at room temperature was improved by 15% due to high electric conductivity caused by the controlled oxygen contents present at bismuth telluride materials.
4,000원
9.
2010.04
구독 인증기관 무료, 개인회원 유료
The ultrafine titanium carbonitride () particles below 100 nm in mean size, including various carbon and nitrogen contents (x=0.55~0.9, y=0.1~0.5), were successfully synthesized by new Mg-thermal reduction process. Nanostructured sub-stoichiometric titanium carbide () particles were initially produced by the magnesium reduction of gaseous at and post heat treatments in vacuum were performed for 2 hrs to remove residual magnesium and magnesium chloride mixed with . Finally, well C/N-controled phases were successfully produced by nitrification heat treatment under normal gas atmosphere at for 2 hrs. The values of purity, mean particle size and oxygen content of produced particles were about 99.3%, 100 nm and 0.2 wt.%, respectively.
4,000원
10.
2010.04
구독 인증기관 무료, 개인회원 유료
Thermal barrier systems have been widely investigated over the past decades, in order to enhance reliability and efficiency of gas turbines at higher temperatures. Yttria-stabilized zirconia (YSZ) is one of the most leading materials as the thermal barriers due to its low thermal conductivity, thermodynamic stability, and thermal compatibility with metal substrates. In this work, rare-earth oxides with pyrochlore phases for thermal barrier systems were investigated. Pyrochlore phases were successfully formed via solid-state reactions started from rare-earth oxide powders. For the heat-treated samples, thermo-physical properties were examined. These rare-oxide oxides showed thermal expansion of and thermal conductivity of 1.2~2.4 W/mK, which is comparable with the thermal properties of YSZ.
4,000원
11.
2010.04
구독 인증기관 무료, 개인회원 유료
In this study, the sintering behavior of (Nd, Dy)-Fe-B powder which fabricated by strip-casting was investigated with various sintering temperatures and holding times. The relative density over 99% could be obtained by both sintering at for 1h and sintering at for 20h. The grain growth was observed in sintered specimen at compared to one at . The isothermal sintering process below led to suppress grain growth showing the improved magnetic properties. The phase transformation of Nd-rich was confirmed by X-ray diffraction pattern.
4,000원
