간행물
한국분말야금학회지 KCI 등재 Journal of Korean Powder Metallurgy Institute
- 발행기관 한국분말재료학회(구 한국분말야금학회)
- 자료유형 학술지
- 간기 격월간
- ISSN 1225-7591 (Print)2287-8173 (Online)
- 수록기간 1994 ~ 2024
- 주제분류 공학 > 금속공학 공학 분류의 다른 간행물
- 십진분류KDC 559DDC 629
권호리스트/논문검색
Vol. 14 No. 3 (2007년 6월) 9건
1.
2007.06
구독 인증기관 무료, 개인회원 유료
본 고에서는 최근 재료분석에 활발히 응용되고 있는 EELS 분석장비의 원리와 응용 분야 등에 대해 검토하였다. EELS를 이용하여 수행할 수 있는 주요 응용분야로는 원소의 정성 및 정량분석, 원소 및 화학 맴핑, 화학물의 결함구조를 알 수 있는 전자구조(DOS)에 대한 힌트 등이 있으며, 점차 재료의 근본 적인 성질을 추출할 수 강력한 분석기가 되고 있다. 또한 원소를 분석하고 맹핑하는데 걸리는 시간이 수초에서 수분 이하의 시간으로 매우 짧아 전자빔에
4,000원
2.
2007.06
구독 인증기관 무료, 개인회원 유료
4,000원
3.
2007.06
구독 인증기관 무료, 개인회원 유료
In the metallothermic reduction (MR) process used to obtain tantalum powder in one batch, it is difficult to control the morphology and location of the tantalum deposits. On the other hand, an electronically mediated reaction (EMR) process is capable of overcoming this difficulty. The effect of using as the raw material and sodium as the reducting agent on the characteristics of tantalum powder are investigated. As the temperature of the reduction varied from 1023K to 1223K, the powder particles obtained with MR were relatively large , while those prepared via EMR were of uniform . In the MR process, the Ta powder recovery rate increased from 37% to 83% at 1123K in constrat with EMR process.
4,000원
4.
2007.06
구독 인증기관 무료, 개인회원 유료
The material design and synthesis are of important to modem science and technology. Here, we report the synthesis of multifunctional nanomaterials with different properties: feroelecties and multiferroic materials such as nano-composites by using a chemical synthesis process. These results provide a simple and convenient synthesis process to produce multifunctional nanocomposites.
4,000원
5.
2007.06
구독 인증기관 무료, 개인회원 유료
Various approaches have been proposed to increase the green density. Warm compaction method has been used for the reduction of residual stress, the improvement of magnetic properties and the higher densities. In this work, the effect of warm compaction on green density of Fe powder was investigated. After ball-milling of Fe oxide powder for 30 hours, Fe oxide powder was reduced through the hydrogen reduction process. The pure Fe powder and polymer binder were mixed by 3-D tubular mixer. And then the mixed powder was warm-compacted with various compaction pressure and binder contents. The green density of specimen was added polyvinyl binder was higher than any other specimens.
4,000원
6.
2007.06
구독 인증기관 무료, 개인회원 유료
A process known as the MR and EMR combination process is able to overcome the shortcomings of the MR (metallothermic reduction) and EMR (electronically mediated reaction) process. The effects of as the raw material, sodium as the reducing agent and KCl/KF as the diluent on the characteristics of tantalum powder are investigated. In this study, a MR-EMR combination process has been employed to tantalum powder on the location of reductant. The excess of reductant were varied from 25, 50 to 75 wt%. The total charge and external circuit decreases as the amount of reductant increases. The average particle size increases with increasing the amount of reductant.
4,000원
7.
2007.06
구독 인증기관 무료, 개인회원 유료
Bulk metallic glass (BMG) composite was fabricated by consolidation of milled metallic glass composite powders. The metallic glass composite powder was synthesized by a controlled milling process using the Cu-based metallic glass powder blended with 30 vol% Zr-based metallic glass powders. The milled composite powders showed a layered structure with three metallic phases, which is formed as a result of mechanical milling. By spark plasma sintering of milled metallic glass powders in the supercooled liquid region, a fully dense BMG composite was successfully synthesized.
4,000원
8.
2007.06
구독 인증기관 무료, 개인회원 유료
Novel polymer mold process for fabrication of microcomponents using metal nanopowders was developed and experimentally optimized. Polymer mold for forming green components was produced by using a hard master mold and polydimethylsiloxane (PDMS). In the preparation of metallic powder premix for the green components without any defect, 90 wt.% 17-4PH statinless steel nanopowders and 10 wt.% organic binder were mixed by a ball milling process. The green components with very clear gear shape were formed by filling the powder premix into the PDMS soft mold in surrounding at about . Cold isostatic pressing (CIP) was very potent process to decrease a porosity in the sintered microcomponent. The microgear fabricated by the improved process showed a good dimension tolerance of about 1.2%.
4,000원
9.
2007.06
구독 인증기관 무료, 개인회원 유료
The microstructure and hardness of (W,Ti)C cemented carbides with a different metallic binder composition of Ni and Co fabricated by powder technology were investigated. The densifications of the prepared materials were accomplished by using vacuum sintering at . Nearly full dense (W,Ti)C cemented carbides were obtained with a relative density of up to 99.7% with 30 wt.% Co and 99.9% with 30 wt.% Ni as a metallic binder. The average grain size of the (W,Ti)C-Co and the (W,Ti)C-Ni was decreased by increasing the metallic binder content. The hardness of the dense (W,Ti)C-15 wt%Co and (W,Ti)C-15 wt%Ni, was greater than that of the other related cemented carbides; in addition, the cobalt-based cemented carbides had greater hardness values than the nickel-based cemented carbides.
4,000원
