The current study, which consisted of two independent studies (laboratory and greenhouse), was carried out to project the hypothesis fungi-spray scheduling for leaf mold and gray leaf spot in tomato, as well as to evaluate the effect of temperature and leaf wet duration on the effectiveness of different fungicides against these diseases. In the first experiment, tomato leaves were infected with 1 × 104 conidia·mL-1 and put in a dew chamber for 0 to 18 hours at 10 to 25°C (Fulvia fulva) and 10 to 30°C (Stemphylium lycopersici). In farm study, tomato plants were treated for 240 hours with diluted (1,000 times) 30% trimidazole, 50% polyoxin B, and 40% iminoctadine tris (Belkut) for protection of leaf mold, and 10% etridiazole + 55% thiophanate-methyl (Gajiran), and 15% tribasic copper sulfate (Sebinna) for protection of gray leaf spot. In laboratory test, leaf condensation on the leaves of tomato plants were emerged after 9 hrs. of incubation. In conclusion, the incidence degree of leaf mold and gray leaf spot disease on tomato plants shows that it is very closely related to formation of leaf condensation, therefore the incidence of leaf mold was greater at 20 and 15°C, while 25 and 20°C enhanced the incidence of gray leaf spot. The incidence of leaf mold and gray leaf spot developed 20 days after inoculation, and the latency period was estimated to be 14‒15 days. Trihumin fungicide had the maximum effectiveness up to 168 hours of fungicides at 12 hours of wet duration in leaf mold, whereas Gajiran fungicide had the highest control (93%) against gray leaf spot up to 144 hours. All the chemicals showed an around 30‒50% decrease in effectiveness after 240 hours of treatment. The model predictions in present study could be help in timely, effective and ecofriendly management of leaf mold disease in tomato.

콘크리트 충전강관은 국부좌굴을 방지하고 내화성이 향상되기 때문에 건설현장에서 많이 적용되며 휨성능을 향상시 키기 위해 강관 내부에 철근을 보강하여 사용한다. 그러나 철근은 부식되며 내구성이 저하되기 때문에 이를 대신할 소재에 대 한 연구가 진행되고 있다. 탄소섬유보강근은 철근에 비해 경량이며 고강도와 내부식성이 우수하다는 이점이 있다. 그러나 임계 온도가 250℃로 철근의 임계온도인 538℃에 비해 현저히 낮기 때문에 내화피복이 필요하다. 따라서 열전달해석을 통해 탄소섬 유보강근을 사용하였을 때 온도분포를 확인하고 P-M상관도를 도출하여 적용 가능여부를 확인하고자 한다. 해석결과 내화성능을 확보하기 위해 콘크리트 피복두께 40mm, 뿜칠내화피복재 30mm를 적용하거나 콘크리트 피복두께 60mm, 뿜칠내화피복재 20mm 를 적용하면 3시간 내화성능을 만족하는 것으로 평가되었다.

PURPOSES : The increasing heat wave warnings during the summer season in Korea have significant impacts on daily life and industry as a whole, especially in urban areas (such as areas with asphalt and sidewalk pavements). Heat waves directly affect urban heat island and heat dome phenomena. Various urban temperature reduction measures are being discussed to reduce urban heat islands and heat dome phenomena and to improve citizen safety against summer heat waves; suggestions include thermal packaging, rooftop greening, and expansion of vegetation areas. There is a lack of analysis on the methodology for increasing the road spraying effect during summer heat waves (e.g., there is no systematic engineering study on the effect from reducing the temperature of the road spraying during a heat wave in the city) and on the types of road pavements in the city. In addition, as the asphalt pavements of roadways and block pavements installed in sidewalks account for a considerable portion of all pavements, this study provides a more systematic and scientific approach and procedures for reducing temperatures through road spraying in the city by tracking the effects of heat waves. METHODS : In this preliminary experiment, four types of road pavement materials were selected as test specimens: asphalt test specimens (AP- 300 mm × 300 mm × 50 mm), concrete test specimens (CP-300 mm × 300 mm × 50 mm), impermeable blocks (IB-200 mm × 200 mm × 60 mm), and self-permeable blocks (PB-200 mm × 200 mm × 60 mm). As a test method to evaluate the size and duration of each spray effect package type, the surface temperature of each specimen was measured using thermal imaging cameras every 20 min after spraying at the maximum temperature point of each specimen, and the average surface temperature was analyzed based on the collected temperature data. In addition, to conduct a quantitative analysis of the effect of reducing the surface temperature of road pavements by road spraying in summer, field tests were conducted on asphalt roads and watertight blocks for sidewalks. RESULTS : As a result of the comparative analysis of the spray effect under a 36 ℃ air temperature based on a heat wave warning, the surface temperatures were, from high to low, the asphalt (68.8 ℃), concrete (59.1 ℃), impermeable block (57.3 ℃), and permeable block (58.7 ℃). The asphalt pavement had the greatest effect on the heat island and heat dome phenomena. From measuring the temperature reduction effect and sustainability of each type of road pavement, the surface temperature reduction effects were ranked in the following order: water-permeable block (Δ18.0 ℃), asphalt test piece (Δ17.5 ℃), concrete test piece (Δ12.2 ℃), and water-permeable block (over 240 min). In the report pitching block, the average road surface temperature reduction between the pore recovery and treatment was expected to continue to decrease by approximately -4.3 ℃ on the day of work and approximately -2.4 ℃ on the next day. The expected effect of the temperature reduction owing to simple spraying on the surface of the pore block was evaluated to be limited to the day. CONCLUSIONS : In the road spray effect analysis conducted on the common asphalt road, there was a slight difference in the initial temperature reduction size as the test specimen was measured, but the surface temperature difference between the non-spray section and spray section tended to be approximately Δ3°C after 140 minutes of spraying. Therefore, it was determined that the asphalt pavement temperature reduction plan through road spraying in urban areas in summer would be the most effective if it was repeated twice or more in an hour (between 13:00 and 14:00) on the day of the heat wave.

A Cu-15Ag-5P filler metal (BCuP-5) is fabricated on a Ag substrate using a high-velocity oxygen fuel (HVOF) thermal spray process, followed by post-heat treatment (300oC for 1 h and 400oC for 1 h) of the HVOF coating layers to control its microstructure and mechanical properties. Additionally, the microstructure and mechanical properties are evaluated according to the post-heat treatment conditions. The porosity of the heat-treated coating layers are significantly reduced to less than half those of the as-sprayed coating layer, and the pore shape changes to a spherical shape. The constituent phases of the coating layers are Cu, Ag, and Cu-Ag-Cu3P eutectic, which is identical to the initial powder feedstock. A more uniform microstructure is obtained as the heat-treatment temperature increases. The hardness of the coating layer is 154.6 Hv (as-sprayed), 161.2 Hv (300oC for 1 h), and 167.0 Hv (400oC for 1 h), which increases with increasing heat-treatment temperature, and is 2.35 times higher than that of the conventional cast alloy. As a result of the pull-out test, loss or separation of the coating layer rarely occurs in the heat-treated coating layer.

This study demonstrates the effect of the compaction pressure on the microstructure and properties of pressureless-sintered W bodies. W powders are synthesized by ultrasonic spray pyrolysis and hydrogen reduction using ammonium metatungstate hydrate as a precursor. Microstructural investigation reveals that a spherical powder in the form of agglomerated nanosized W particles is successfully synthesized. The W powder synthesized by ultrasonic spray pyrolysis exhibits a relative density of approximately 94% regardless of the compaction pressure, whereas the commercial powder exhibits a relative density of 64% under the same sintering conditions. This change in the relative density of the sintered compact can be explained by the difference in the sizes of the raw powder and the densities of the compacted green body. The grain size increases as the compaction pressure increases, and the sintered compact uniaxially pressed to 50 MPa and then isostatically pressed to 300 MPa exhibits a size of 0.71 m. The Vickers hardness of the sintered W exhibits a high value of 4.7 GPa, mainly due to grain refinement.

In this study, a new manufacturing process for a multilayer-clad electrical contact material is suggested. A thin and dense BCuP-5 (Cu-15Ag-5P filler metal) coating layer is fabricated on a Ag plate using a high-velocity oxygen-fuel (HVOF) process. Subsequently, the microstructure and bonding properties of the HVOF BCuP-5 coating layer are evaluated. The thickness of the HVOF BCuP-5 coating layer is determined as 34.8 μm, and the surface fluctuation is measured as approximately 3.2 μm. The microstructure of the coating layer is composed of Cu, Ag, and Cu-Ag-Cu3P ternary eutectic phases, similar to the initial BCuP-5 powder feedstock. The average hardness of the coating layer is 154.6 HV, which is confirmed to be higher than that of the conventional BCuP-5 alloy. The pull-off strength of the Ag/BCup-5 layer is determined as 21.6 MPa. Thus, the possibility of manufacturing a multilayer-clad electrical contact material using the HVOF process is also discussed.

The purpose of this study is to improve the mechanical properties and develop manufacturing technology through self-soluble alloy powder flame spray coating on the surface of a run-out table roller for hot rolling. The roller surface of the run-out table should maintain high hardness at high temperatures and possess high wear, corrosion, and heat resistances. In addition, sufficient bonding strength between the thermal spray coating layer and base material, which would prevent the peel-off of the coating layer, is also an important factor. In this study, the most suitable powder and process for roll manufacturing technology are determined through the initial selection of commercial alloy powder for roll manufacturing, hardness, component analysis, and bond strength analysis of the powder and thermal spray coating layer according to the powder.

본 연구에서는 감귤원에서 초생재배 유무(초생재배 W, 제초제 살포 NW)와 합성피레스로이드계 살포유무(살포 P, 무살포 NP)에 따른 귤 응애의 개체군 동태를 구명하고자 수행되었다. 두 가지 기본적인 가설로 1) 초생재배는 천적의 서식처를 제공하여 천적의 정착을 높이므로 귤응 애의 발생을 감소시키는 요인으로 작용하며, 2) 합성피레스로이드계는 천적을 제거하여 귤응애의 밀도를 증가시키는 요인으로 가정하였다. 관측 된 천적 개체군(주로 이리응애류와 마름응애류)의 발생은 가정에 근거한 기대치와 크게 다르지 않았다. 2011년의 경우 NW+NP 처리구와 W+NP 처리구에서 차이가 있었으나, 2012년 실험에서는 기대치와 관측치가 거의 일치하였다. 전체적으로 약제효과가 뚜렷하게 나타나서 합성 피레스로이드계 살포시 천적이 유의하게 감소하였다. 잡초효과는 엇갈리는 결과를 보였는데, 봄-유래 여름 개체군 대비 가을 개체군의 증가 등을 고려할 때 초생재배를 하는 경우 천적의 발생이 증가하였다. 다만, 합성피레스로이드계 살포구에서 귤응애가 감소하는 비이상적인 결과는 귤응 애의 합성피레스로이드계에 대한 강한 기피성을 전제로 해석할 수 있었다.

The effect of the process conditions of high-velocity oxygen fuel (HVOF) thermal spray coating on the porosity of the coating layer is investigated. HVOF coating layers are formed by depositing amorphous FeMoCrBC powder. Oxygen pressure varies from 126 to 146 psi and kerosene pressure from 110 to 130 psi. The Microstructural analysis confirms its porosity. Data analysis is performed using experimental data. The oxygen pressure-kerosene pressure ratio is found to be a key contributor to the porosity. An empirical model is proposed using linear regression analysis. The proposed model is then validated using additional test data. We confirm that the oxygen pressure-kerosene pressure ratio exponentially increases porosity. We present a porosity prediction model relationship for the oxygen pressure-kerosene pressure ratio.

절화용 스프레이 국화(Dendranthema grandiflorum)는 다양한 화색, 화형을 가진 품종들이 많지만, 국내에서는 시장성이 낮은 편이다. 따라서 고품질 국화 생산을 통한 소비 확대가 필요하며 연중 균일하게 환경을 조절해주는 스마트팜 기술 을 활용하여 일정한 품질의 국화를 생산하는 것이 중요하다. 본 연구에서는 스마트팜과 관행농가에서 채화한 절화용 스프레이 국화 ‘헤나’의 절화수명과 품질을 비교 분석하였다. 절화 수명의 경우 스마트팜은 28.6±1.03일, 관행농가는 24.2±0.61로 스마트팜이 약 4.4일 길게 유지하였다. 절화중 변화율의 경우 스마트팜은 최대 117.95%까지 증가하였으며 27일간 초기 절화중보다 높은 절화중을 유지했다. 관행농가는 최대 116.65%까지 증가하였으며, 21일간 유지했다. 수분 흡수량의 경우 스마트팜은 절화수명 종료시점까지 10mL 이상을 흡수하였으나, 관행농가는 Day 12부터 10mL 이하만 흡수하였다. 수 분균형의 경우 스마트팜과 관행농가 모두 Day 2에 최고치를 나타냈으나, 급격히 감소하여 스마트팜은 Day 8에, 관행농가 는 Day 6에 음수값에 도달하였다. 화폭 변화율의 경우 스마트 팜은 최대 143.00%까지 증가하였으며, 관행농가는 최대 125.82% 까지 증가했다. 엽록소 함량의 경우 이 전 결과와는 달리 Day 0에는 관행농가가 약 7.56 SPAD value 만큼 더 높았으나, 절화수명 종료시점까지 스마트팜이 더 큰 폭으로 증가하였다. 종합적으로, 절화용 스프레이 국화를 스마트팜에서 채화할 경 우 절화수명 및 품질이 더 향상되었음을 알 수 있었다.

The effects of different spray angles (90°, 85°, 80°) on the microstructure and mechanical properties of a Y2O3 coating layer prepared using the atmospheric plasma spray (APS) process were studied. The powders employed in this study had a spherical shape and included a cubic Y2O3 phase. The APS coating layer exhibited the same phase as the powders. Thickness values of the coating layers were 90°: 203.7 ± 8.5 μm, 85°: 196.4 ± 9.6 μm, and 80°: 208.8 ± 10.2 μm, and it was confirmed that the effect of the spray angle on the thickness was insignificant. The porosities were measured as 90°: 3.9 ± 0.85%, 85°: 11.4 ± 2.3%, and 80°: 12.7 ± 0.5%, and the surface roughness values were 90°: 5.9 ± 0.3 μm, 85°: 8.5 ± 1.1 μm, and 80°: 8.5 ± 0.4 μm. As the spray angle decreased, the porosity increased, but the surface roughness did not show a significant difference. Vickers hardness measurements revealed values of 90°: 369.2 ± 22.3, 85°: 315.8 ± 31.4, and 80°: 267.1 ± 45.1 HV. It was found that under the condition of a 90° angle with the lowest porosity exhibited the best hardness value. Based on the aforementioned results, an improved method for the APS Y2O3 coating layer was also discussed.

연중생산이 가능하고 특히, 저온에서 화색발현이 우수하며 볼륨감 있는 스프레이국화 신품종을 개발하기 위하여 충청남 도농업기술원 화훼연구소에서 2010년에 모본으로 황색의 홑꽃 ‘SP09-251-01’를 부본으로 ‘SP08-010-16’계통을 인공수분 하였다. 종자 파종은 2011년에 실시하였고, 실생개체 중 화색과 화형이 우수한 281번째 개체를 선발하여 ‘SP11-103-05’로 계통명을 부여하였다. 주년생산성 검정을 위하여 2011년부터 2013년까지 자연일장, 전조재배, 차광재배를 각각 실시하였고, ‘Yes Holic’과 화형, 화색, 초형이 비슷한 ‘Jazz’ 품종을 대조품 종으로 사용하였다. ‘Yes Holic’ 품종은 2013년에 국립종자원에 품종보호 출원을 하였다. ‘Yes Holic’은 황색(Yellow 7A)의 꽃잎과 녹색(Green 1B)의 화심색으로 조사되었고 자연일장 작형의 개화기는 10월 25일로 ‘Jazz’의 10월 26일에 비해 빨랐다. ‘Yes Holic’의 초장과 줄기굵기는 각각 80.2cm와 6.1mm 로 ‘Jazz’의 78.6cm와 5.3mm보다 컸다. ‘Yes Holic’의 꽃 직경은 4.4cm로 ‘Jazz’의 4.1cm보다 컸으며, 착화수도 ‘Yes Holic’ 가 29.4개로 ‘Jazz’의 22.1개보다 많았다. 흰녹병저항성은 ‘Yes Holic’이 10%이하의 발병율인 3단계로 흰녹병이 저항성이 높은 것으로 확인되었다. 재배상 유의사항은 ‘Yes Holic’은 소등 후 야간온도를 18℃로 가온하면 고유화색 발현과 적당한 착화수 확보 및 균일한 개화가 가능하다. 그리고 여름철 고온기에는 ‘Yea Holic’의 총포에 잿빛곰팡이병이 주로 발생되므로 스크린과 포그를 활용하여 주간온도를 낮추고 봉오리 착색기에 전용 농약을 살포해 주어야 한다.

본 연구는 손상된 선박용 절탄기 핀튜브에 대하여 보수를 목적으로 Inconel 625 아크 열용사 코팅기술 적용 후 실링처리를 실시하였다. 모재(Substrate), 열용사 코팅(Thermal Srpay Coating; TSC) 그리고 열용사 코팅+실링처리(TSC+Sealing) 시편에 대하여 내구성을 평가하기 위해 ASTM G76-05에 의거하여 고상입자 침식(Solid Particle Erosion; SPE) 실험을 실시하였다. 표면 손상 형상은 주사전자현미경과 3D 레이져 현미경을 통해 관찰했으며, 무게 감소량과 표면 거칠기 분석을 실시하여 내구성을 평가하였다. 그 결과 내구성은 TSC와 TSC+Sealing에 비해 Substrate가 우수하게 나타났으며, 이는 TSC 층 내에 존재하는 다수의 기공 결함에 기인한 것으로 판단된다. 또한 고상 입자 침식 손상 메카니즘은 Substrate의 경우 연성 재질 특성인 소성변형과 피로에 의한 균열 생성이 동반되었으며, TSC와 TSC+Sealing의 경우 취성파괴 경향이 확인되었다.