Due to severe environmental pollution from ships, IMO(International Maritime Organization) is imposing strict controls on pollutant emission in ECA(Emission Control Area). There have been active studies to find fuel that could replace existing fossil fuel and especially in recent times, diverse studies on recycling of coffee ground are in progress. The annual domestic consumption of coffee was 150,000 tons according to the data of 2017 year and 99% of them are coffee ground to be scrapped. Therefore, in this study, coffee ground was mixed with diesel oil to develop alternative fuel. The analysis result showed that when coffee ground and diesel oil were mixed at a rate of 30%, 20% and 10%, the diameter of coffee ground droplet was 49.1μm, 45.9μm and 17.5μm respectively.

PURPOSES : The cooling characteristics of the asphalt mixture in a moving dump truck were analyzed using a numerical simulation method. The cooling characteristic can be used to determine the optimum transport path for minimizing the temperature drop of the asphalt mixture. METHODS : In this research, a coupled analysis of the discrete element method (DEM) with computational fluid dynamics (CFD) was applied for cooling characteristic analysis of asphalt mixtures in transit. Two different transit speeds, 30 km/h and 60 km/h, were considered to evaluate the effect of speed on the temperature drop of the asphalt mixture. Velocity, pressure, and temperature contours were plotted and temperature variations were compared. RESULTS : Most of the temperature drops in the asphalt mixture were observed in the middle of the dump box in the longitudinal direction. It was confirmed that a faster speed causes a greater temperature drop for the same travel time and a slower speed causes the more temperature to reach the same travel distance as expected. CONCLUSIONS : It is concluded that the coupled analysis method can be used to quantitatively evaluate the effect of vehicle speed on temperature drop in asphalt mixtures. In addition, the method can be used to determine the optimum travel path considering environmental conditions and traffic congestion.

국제해사기구(IMO)의 황함유량 규제에 따르는 저유황연료유는 생산 공정에 따라 다양한 물리화학적 특성을 가지게 된다. 본 연구는 저유황연료유 및 저유황-고유황 혼합연료유의 물리화학적 특성연구 결과를 해양오염 방제대응의 기초자료로 활용하고자 한다. 연구에 사용된 혼합연료유는 황함유량이 0.46 mass%인 저유황연료유와 0.36 mass%인 저유황연료유에 고유황연료유를 25, 50, 75 mass% 혼합하여 제조하였다. 이 혼합연료유에 대해 동점도, 유동점 및 Saturates, Aromatics, Resins, Asphaltenes(SARA)분포 등 물리화학적 특성에 대해 실험실 연구를 하였다. 동점도가 높고 유동점이 낮은 특징의 고유황연료유가 75 mass% 혼합함에 따라, 혼합연료유의 동점도는 350.2 %까지 증가 하였으며, 유동점이 23℃와 -11℃의 저유황연료유는 각각 -3℃ 및 -6℃까지 유동점이 내려가거나 올라갔다. Asphaltenes 분포가 적은 저유황연료유에 고유황연료유를 혼합함에 따라, Saturates분포는 68.8 %까지 감소하고, Asphaltenes분포는 1,417 %까지 크게 증가하였다.

PURPOSES : The purpose of this study is to analyze the effect of ions in emulsion asphalt on recycling cold asphalt concrete and suggest the possibility of using anionic and nonionic emulsion asphalt. METHODS : In this study, indirect tensile strength, toughness, tensile strength ratio, and dynamic immersion tests were conducted to determine the effects of cation, anion, and non-ion emulsified asphalt on the cold recycled asphalt mixture. Crack resistance was evaluated through indirect tensile strength and toughness tests and the tensile strength ratio and dynamic immersion test were evaluated through tensile strength ratio and dynamic water immersion test. RESULTS : Indirect tensile strength and toughness measurement results demonstrated that the mixture using anion and non-ion emulsified asphalt tended to be higher than that using cation emulsified asphalt; this is due to the high content of reclaimed asphalt pavement with a cationic or ionic surface, which is related to the use of cation-emulsified asphalt in the mixture and has shown a low strength tendency. The tensile strength ratio measurement demonstrated that the mixture using non-ion emulsified asphalt tended to be approximately 15 % higher than that of the anion mixture. This demonstrated that the chemical additive used in the mixture showed a complete hydration reaction with the distribution to the mixture. The dynamic immersion test indicates that the aggregate film rate of asphalt is highly influenced by the surface electric charge of the new aggregate while the ionicity effect appears to be insignificant, at 75 - 85 %, when circular aggregates are used. CONCLUSIONS : High reclaimed asphalt pavement content in cold recycled asphalt mixture, as well as non-ion and anionic emulsified asphalt, is advantageous, reducing cracking and improving moisture resistance. It is believed that anions and non-ions may be better utilized than applying the existing criteria to the cold temperature recycled asphalt mixture with high reclaimed asphalt pavement content. In addition, if the scope of the emulsified asphalt is expanded, various additives can be used, which will require analysis of materials, such as fertilizers and additives.

PURPOSES : The objective of this study is to address various problems, such as an increase in material cost and premature failure (e.g., cracks and potholes) of porous pavements, and to develop multifunctional asphalt and asphalt mixtures to ensure the long-term commonality of porous asphalt pavements. METHODS : A basic quality test of two types of porous asphalt mixtures was performed. One type consisted of the existing porous asphalt mixture, using domestically presented grading, and the other a porous asphalt mixture using high-viscosity modified asphalt with enhanced low-temperature properties, aimed at improving strain resistance and developed by applying the grading suggested by the Federal Highway Administration (FHWA). RESULTS : The cantabros loss rate was 19.62 % for conventional modified asphalt (PG 82-22) and 5.95 % for the developed highviscosity modified asphalt (PG 88-28), indicating that both mixtures passed the criteria. Regarding the drain-down loss rate, mixtures using both types of asphalt were found to pass all quality standards. The average permeability coefficients for each porous asphalt mixture were 0.023 and 0.018 and both types of porous asphalt mixtures satisfied the quality standard of 0.01 cm/s, as given by the Asphalt Concrete Pavement Guidelines of the Ministry of Land, Infrastructure, and Transport. CONCLUSIONS : As a result of the mix design of the two porous asphalt mixtures, the mixture developed in this study was found to be superior to the conventional porous asphalt mixture using conventional porous asphalt grading and modified asphalt.

In this study, four types of water-heavy fuel oil hybrid emulsion oil were manufactured depending on the moisture content ratio in order to reduce exhaust emissions of heavy fuel oil(Bunder-C), which is necessarily used in vessels, power plants and boilers. The components of the manufactured emulsion oil were analyzed using the ISO standard testing method. The analysis result showed that in the EM25 fuel with a maximum moisture content ratio of 25.0%, the moisture content was 25.0%, the sulphur content was 0.20%, the kinematic viscosity was 144.8mm2/s, the specific gravity was 0.9382, and the flash point was 100 Celsius degrees or above.

In this paper, a durability study is presented to enhance the mechanical properties of an Fe-Si-Al powderbased magnetic core, through the addition of graphite. The compressive properties of Fe-Si-Al-graphite powder mixtures are explored using discrete element method (DEM), and a powder compaction experiment is performed under identical conditions to verify the reliability of the DEM analysis. Important parameters for powder compaction of Fe-Si-Algraphite powder mixtures are identified. The compressibility of the powders is observed to increase as the amount of graphite mixture increases and as the size of the graphite powders decreases. In addition, the compaction properties of the Fe-Si-Al-graphite powder mixtures are further explored by analyzing the transmissibility of stress between the top and bottom punches as well as the distribution of the compressive force. The application of graphite powders is confirmed to result in improved stress transmission and compressive force distribution, by 24% and 51%, respectively.

This study is carried out to analyze the velocity distribution for each location and the uniformity index according to straight distance on exit side by changing the design factors of branch pipe connected to 180° circular mixing-tee using RSM(Reynolds Stress Model) turbulence model. As the results of the flow characteristics according to hydraulic diameter, the velocity profiles in the 90° sectional area are generally similar. In the 180° section, the maximum velocity point shows Y/D=0.7~0.8 after rapid increase of the flow velocity. In the result according to the distance away from inlet, the maximum velocity point in the 90° sectional area is located in outer side of the curved pipe as the distance away from inlet increases. In the 180° sectional area, the maximum velocity point is showed in Y/D=0.7~0.8 after the rapid increase of the flow velocity regardless of the variation of branched distance. In case of inclined angle, the maximum velocity point in the 90° sectional area is located in outer side of the curved pipe as the inclined angle increases. In the 180° sectional area, the maximum velocity point is observed in Y/D=0.8 regardless of the inclined angle. In addition, the uniformity index of flow velocity shows that it is stabilizing after approximately L/D=40 away from the end of the curved pipe regardless of the flow factors in the branch pipe.

Melon is a fruit consumed and grown globally because of the sweet taste and pleasant aroma. The purpose of this study was to determine the quality characteristics and antioxidant activities of melon jams added with various fruits such as apple, aronia, blueberry, grape, kiwi, passion fruit, and peach. We determined quality characteristics such as pH, total acidity, antioxidant activity, content of total anthocyanin, polyphenol and tannin, respectively. The 100% melon jam as the control was the highest pH and lowest total acidity, whereas mixed jams with melon and passion fruit showed opposite results. The mixed jams with melon and aronia of the total anthocyanin, the polyphenol contents, tannin, and ABTS radical scavenging activities, were markedly higher than those of the control and other samples (p<0.001), followed by the mixed jams with melon and blueberry. In the taste sensing analysis, mixed jams with melon and passion fruit revealed higher richness and lower aftertaste-bitterness and aftertaste-astringency than the commercial strawberry jam and other samples. Thus, jams mixed with various fruits, in particular, aronia, blueberry, and passion fruit were superior to the 100% melon jam in terms of physiological activity and palatability.

In this study, we investigated the effects of diesel-palm oil biodiesel-ethanol blends on combustion and emission characteristics in a 4-cylinder common rail direct injection (CRDI) diesel engine at low idling operations. The engine speed and engine load was 750 rpm and 40 Nm, while the main and pilot injection timing was respectively fixed at 2 °CA before top dead center (BTDC) and 20 °CA BTDC. The experimental results showed that the cylinder pressure increased with the increasing of palm oil biodiesel ratio from 20% to 100%. In addition, the peak value of cylinder pressure increased by 4.35% compared with pure diesel fuel when 5 vol.% ethanol oil added to diesel oil. Because the palm oil biodiesel and ethanol are the oxygenated fuel, the oxygen content played an important role in improving combustion. Based on the high oxygen content of biodiesel and ethanol, their mixing with diesel fuel effectively reduced PM emissions but increased NOx slightly, while CO and HC had no significant changes.

Small fishing vessels are manufactured using FRP. Various studies have been conducted to increase the strength of the composite material by mixing alumina powder with resin. Tensile tests and flexural strength tests are conducted to examine the effect of alumina powder on the strength of GFRP. In the current study, resin/alumina composites at different alumina contents (i.e., 0, 1, 5, and 10 vol%) have been prepared. The physical and mechanical properties of the prepared composites have been investigated. From the results, the tensile strength of the specimen with alumina powder mixed in at 10% shows the highest value of 155.66 MPa. The tensile strength of the specimen mixed with alumina powder increases with the amount of alumina powder impregnated. In the flexural strength test, the flexural strength of neat resin without alumina powder has a highest value of 257.7 MPa. The flexural modulus of ALMix-5 has a highest value of 12.06 GPa. Barcol hardness of ALMix- 10 has a highest value of 51. We show that alumina powder leads to decreasing cracks on the surface and decreasing length area of delamination.

In this study, to investigate the effect of physical and chemical properties of butanol on the engine performance and combustion characteristics, the coefficient of variations of IMEP (indicated mean effective pressure) and fuel conversion efficiency were obtained by measuring the combustion pressure and the fuel consumption quantity according to the engine load and the mixing ratio of diesel oil and butanol. In addition, the combustion pressure was analyzed to obtain the pressure increasing rate and heat release rate, and then the combustion temperature was calculated using a single zone combustion model. The experimental and analysis results of butanol blending oil were compared with the those of diesel oil under the similar operation conditions to determine the performance of the engine and combustion characteristics. As a result, the combustion stabilities of D.O. and butanol blending oil were good in this experimental range, and the indicated fuel conversion efficiency of butanol blending oil was slightly higher at low load but that of D.O. was higher above medium load. The premixed combustion period of D.O. was almost constant regardless of the load. As the load was lower and the butanol blending ratio was higher, the premixed combustion period of butanol blending oil was longer and the premixed combustion period was almost constant at high load regardless of butanol blending ratio. The average heat release rate was higher with increasing loads; especially as butanol blending ratio was increased at high load, the average heat release rate of butanol blending oil was higher than that of D.O. In addition, the calculated maximum. combustion temperature of butanol blending oil was higher than that of D.O. at all loads.