초 록 본 실험은 몇가지 우화기구를 사용하여 기구형에 따른 우화상내 온도변화가 솔잎혹파리의 우화소장에 미치는 영향 및 유충의 월동기간중의 온도변화와 우화소장간의 관계를 알아 보기 위하여 각처리별 우화소장을 조사하여 다음과 같은 결과를 얻었다. 1) 우화기구별 상내 최고온도는 현저한 차리를 나타내어 대조구에 비하여 Vinyl형은 월평균 가 높았고 다른 처리구에 있어서도 가 높았는데 다른 처리구에 있어서도 가 높았는데 표준형의 순이었다. 2) 처리별유충의 월동기간중의 최저온도분포는 현저한 차이를 나타내지 않았다. 3) Vinyl형 처리구에서는 우화최성일이 5월 15로 대조구에 비하여 20일 앞당겨했고 표준형구와 Cage-50구도 14일 빨라졌다. 4) Funnel형 처리구에 있어서는 최고온도 및 적산온도의 분포가 대조구에 비하여 높았음에도 불구하고 우화최성일은 6일이 지연되었다. 5) 유충의 월동기간중의 온도처리효과는 12월중순과 3월중순의 최고온도의 상승이 우화최성일을 앞당기는 효과를 나타내었다.

To improve survival rates of vitrified pig oocytes, the treatment of cytoskeletal stabilizer on an appropriate time is one of the possible approaches. However, the exact treatment timing and effect of cytoskeletal stabilizer such as cytochalasin B (CB) is not well known during oocyte vitrification procedures. Thus, the present study was conducted to determine optimal treatment timing of CB during vitrification and warming procedures. In experiment 1, the survival rates of the post-warming pig oocytes were analyzed by fluorescein diacetate (FDA) assays with 4 classifications. In results, post-warming oocytes showed significantly (p<0.05) decreased number of alive oocytes (31.8% vs. 86.4%) compared to fresh control. In detail, the significant difference (p<0.05) was found only in strong fluorescence (18.2% vs. 70.5%) not in intermediate fluorescence groups (13.6% vs. 15.9%). In experiment 2, CB was treated before (CB-Vitri) and after (Vitri-CB) vitrification. In results, group of Vitri-CB showed significantly (p<0.05) higher (91.6%) survival rates compared to group of CB-Vitri (83.7%), significantly (p<0.05) and comparable with group of Vitri Control (88.7%) by morphological inspection. In FDA assay results, group of Vitri-CB showed significantly (p<0.05) higher (44.2%) survival rates compared to groups of CB-Vitri (36.7%) and Vitri Control (35.1%). In conclusion, the increased survival rates of post-warming pig oocyte treated with Vitri-CB method are firstly described here. The main finding of present study is that the CB treatment during recovery could be helpful to refresh the post-warming pig oocyte resulting its improved survival rates.

In order to design the improvement process for T-N removal, the treatment process of Suyoung, Gangbyeon, and Noxan sewage treatment plants (STP) in Busan was anlayzed. Suyoung STP shows a T-N removal efficiency of about 69.8% with MLE(Modified Ludzack ettinger) and A2O+MBR. However, it is necessary to improve the process to maintain over DO of 1 mg/L and is required to install a flow control tank to minimize the rainfall effect. Gangbyun STP shows a about 70.2% T-N removal efficiency with A2O+GFF(gravity fiber filtration). However, in order to improve T-N removal efficiency, it is needed to install MLE process to treat recycle water. Noksan STP shows a T-N removal efficiency of about 71.0% with MLE+Chemical treatment and shows stable T-N concentration in effluent. However, it is required a toxic chemical management process because bad wastewater flows into the STP, also is necessary a process improvement in order to increase internal recycling ratio. Especially, it is required a process improvement to increase HRT of nitrification tank because Suyoung and Gangbyeon STPs shows low nitrification efficiency during winter season.

WtE of MSW plays a crucial role in renewable energy production in Korea. Municipal solid waste (MSW) is an important energy resource for combined heat and power (CHP) production. This study investigated an increasing method to the power generation efficiency by MSW to energy (WtE) plants in South Korea and discussed the issues related to energy efficiency improvement. To achieve energy efficiency improvement is used to lower temperature for emission gas at catalyst inlet, or to reduce/stop using steam to reheat emission gas. Saved energy from this process can be used as power source in order to increase generation efficiency. It is possible to increase denitrification efficiency by maintaining the temperature of emission gas for catalyst denitrification. The temperature of emission gas of which moisture is increased to saturation point (relative humidity of 100%) at the exit of wet scrubber is between 50 and 60℃. This means there should be reheating of emission gas with the approximate temperature of 150℃. Dry emission gas treatment, on the other hand, is the technology to increase generation efficiency by using highly efficient desalination materials including highly-responsive slaked lime and sodium type chemicals in order to comply with air pollution standards and reduce used steam volume for reheating emission gas. If dry emission gas is available, reheating is possible only with the temperature of 45℃ in order to expect generation efficiency by reducing steam volume for reheating.

지난 10년간 매년 15여 건의 재해가 평균적으로 발생하고 있으며, 특히 자연재해 중 수해 빈도수가 가장 높다. 태풍과 호우를 포함한 수해로 인한 피해액이 연간 피해액의 80% 이상에 해당하며, 나머지는 풍랑, 대설 등의 재해가 차지하고 있다. 이와 같이 예상치 못한 재해 발생 시 단기간에 다량의 재해폐기물이 발생하게 되며, 이로 인해 피해지역 주민들은 일상 생활환경에 중대한 피해를 입게 된다. 또한 대규모로 발생한 폐기물은 피해 지역으로의 진･출입을 방해하여 복구 작업이 지연될 가능성이 크다. 현재 수해폐기물은 거의 전량 매립 처분되고 있는 실정이다. 이러한 수해폐기물 내에는 가구나 가전제품 등 재활용이 가능한 물질이 다량 포함되어 있어 기존대로 단순 매립할 경우 자원 낭비를 야기하고 매립지의 수명을 단축시키게 된다. 한편, 일본의 경우 발생된 수해폐기물의 70%가 소각과 재활용으로 처리되고 나머지 30%가 매립되고 있어 국내 현황과 크게 대조된다 할 수 있다. 또한 ｢자원순환기본법｣이 제정･공포됨에 따라 2018년부터 폐기물처분부담금이 시행될 예정에 있어 재해로 인한 폐기물이 면제 대상이 되지 않는다면 수해폐기물 역시 시행 대상으로 이에 대한 준비가 필요하다. 본 연구에서는 국내에서 가장 빈번하게 발생하는 수해로 인해 침수된 생활폐기물을 대상으로 성상별 관리방안을 제시하였다. 특히, 사례조사 지역으로 과거 수해 발생지역 중 생활폐기물이 다량 발생한 지역이면서 최근 수해가 발생한 지역에 초점을 두어 부산시를 대상으로 하였다. 부산시청 및 구청 실무자를 대상으로 인터뷰 및 설문조사를 진행하였으며 수해 당시 임시적환장(선별지)으로 사용된 재활용 선별장을 방문하여 관리상 현황 및 문제점을 도출하였다. 이를 바탕으로 다음의 5가지 측면 - ①수해폐기물 발생량 예측 및 사후 성상별 발생량산정, ②2차 임시적환장의 부지 선정 및 운영 관리, ③수해폐기물의 성상별 처리방법, ④공간정보와 연계한 수해폐기물 광역처리 방안, ⑤사후보고체계 및 통계자료 구축 - 에서 개선방안을 마련하였다.

This study aimed for evaluating the applicability of the two stage dual media filtration system in field water treatment plant. The field plant of two stage and dual media filtration system was operated for 2 months. Average iron concentrations of the settled water, existing filtered water and second stage filtered water was 0.041 mg/L, 0.007 mg/L and 0.005 mg/L, respectively. Removal efficiency of iron concentration in the second stage is appropriately 35% more than in existing filtered water. Also removal efficiency of residual chlorine in the dual media filtration system is relatively 42.3% more than in existing filtered water due to adsorption of activated carbon, but the removal of ammonia nitrogen by adsorption is insufficient. Average concentrations of THM and chloroform in the settled water are 0.033 mg/L, 0.026 mg/L, respectively and in existing filtered water are 0.023 mg/L and 0.023 mg/L. Average concentrations of THM and chloroform in the dual media filtration system are 0.008 mg/L and 0.013 mg/L. Therefore removal efficiency of THM concentration in second stage is more than 66.4% in existing filtrated water. Also removal efficiency of chloroform in the dual media filtration system is more than 50.0% in existing filtered water because of the adsorption of activated carbon. In this case backwashing period in dual stage system is 4～5 days, but in existing filtration system is 1～2 days.

The objectives of this paper are the characterization of the pretreatment of wastewater by microfiltration (MF) membranes for river maintenance and water recycling. This is done by investigation of the proper coagulation conditions, such as the types and doses of coagulants, mixing conditions (velocity gradients and mixing periods), pH, etc., using jar tests. The effluent water from a pore control fiber (PCF) filter located after the secondary clarifier at Kang-byeon Sewage Treatment Plant (K-STP) was used in these experiments. Two established coagulants, aluminum sulfate (Alum) and poly aluminum chloride (PAC), which are commonly used in sewage treatment plants to treat drinking water, were used in this research. The results indicate that the optimal coagulation velocity gradients (G) and agitation period (T) for both Alum and PAC were 200-250 s-1 and 5 min respectively, but the coagulation efficiencies for both Alum and PAC were lower at low values of G and T. For a 60 min filtration period on the MF, the flux efficiencies (J/J0 (%)) at the K-STP effluent that were coagulated by PAC and Alum were 92.9 % and 79.9 %, respectively, under the same coagulation conditions. It is concluded that an enhanced membrane process is possible by effective filtration of effluent at the K-STP using the coagulation-membrane separation process.

본 연구에서는 피로 손상된 용접이음의 피로수명 향상을 위한 방법으로 햄머피닝 처리법의 적용성을 검토하기 위하여 면외거셋 필렛 용접이음과 하중비전달형 리브 필렛 용접이음의 피로실험을 실시하였다. 본 실험에서는 면외거셋과 리브를 필렛 용접한 후 햄머피닝 처리를 하지 않은 용접그대로의 시험편, 용접후 햄머피닝 처리한 시험편, 그리고 용접그대로 시험편의 피로수명의 50% 시점에 햄머피닝 처리를 한 시험편의 피로실험을 실시하였다. 그리고 햄머피닝 처리에 의한 면외거셋과 리브 용접토우부의 형상 및 표면응력의 변화를 측정하였다. 그 결과, 햄머피닝처리에 의해 30~83MPa의 압축잔류응력이 도입 되었으며, 이로 인하여 강구조물의 제작시 용접후에 햄머피닝 처리를 실시하면 피로수명을 크게 향상 시킬 수 있을 뿐만 아니라, 이를 공용기간이 예상 피로수명의 50% 이하인 강구조물의 용접이음에 적용하여도 최소 1.3배 이상의 피로수명과 피로한계 향상효과를 기대할 수 있음을 제시하였다.

The antimicrobial activities of Smilax china L. against spoilage bacteria isolated from Mang-gae rice cake were investigated and the storage stability of the Mang-gae rice cake was enhanced. Spoilage bacteria, which cause Mang-gae rice cake to rot, were isolated from commercial Mang-gae rice cake, and most of the isolated strains were identified as Bacillus sp. After the leaves, roots, shoots, and stalks of the Smilax china L. were extracted using 50% ethanol as the solvent, their antimicrobial activities were investigated using the paper disc method by treating them with 50 μL of Bacillus cereus, which is known as a major pathogenic micro-organism in foods that contain starch, as the test organism. The antimicrobial activities of the extracts were compared according to the size of the clear zones around the paper discs. The root extract showed significant antimicrobial activities. When red beans, which are used as stuffing for Mang-gae rice cake, were treated with the root extract of the Smilax china L., the viable cell count of the Mang-gae rice cake was 5.04 Log CFU/g after 48-hr storage, and the cake showed significantly slower growth of bacteria than with commercial products. These results show that treatment of red beans with Smilax china root extract could improve the storage stability of Mang-gae rice cake.

Pectinase 처리가 복분자 과즙의 추출 수율에 미치는 영향과 알코올 발효 중 이화학적 변화에 대하여 조사하였다. Pectinex 100L 처리(500 ppm, 30분)에 의해 복분자 과즙의 추출 수율은 대조구보다 8.60%가 증가되었다. 설탕 첨가에 의해 에서 발효를 시작한 처리구(24B-group)와 에서 발효를 시작하고 발효 4일 후에 설탕 16%를 첨가한 처리구(8B-group)의 고형분 함량은 발효 10일 후에 각각 와 로 감소하였으

The effluent discharge standards of industrial wastewater has become more stringent since 2003. Many industrial wastewater treatment plants has been upgraded to advanced treatment facilities. There are high concentrations of nitrate(>200 mg/L) and ammonium(>50 mg/L) nitrogen in the acrylic fiber wastewater of H textile Co. Wastewater from acrylic fiber industry containing acrylonitrile, which may affect the subsequent biological treatment process. Manufacturing of acrylic fiber also produces shock loadings. Excessive acrylonitrile and polymer debris produced in the polymerization process was screened, coagulated with CaO and settled down. A preaeration system was added to treat this high pH effluent to remove volatile organic compound and ammonia nitrogen by the air stripping effect. It was found that nitrification rate was not sufficient in the Anoxic/ Oxic(AO) process. One denitrification tank was converted to nitrification reactor to extend HRT of nitrification. Nitrification rate of ammonia nitrogen was promoted from 32% to 67% by this modification and effluent nitrogen concentration was well satisfied with the effluent standards since then.

For the sustainable management of marine ecosystem in Masan Bay, we have to assess the carrying capacity and standard of target water quality. In this research, we assume that all pollutants loads are treated in Dukdong sewage treatment plant, then we simulate the physical-biological model for prediction water quality for the achievement of standard water quality. In 2001 year, for the achievement of COD 2.5 mg/L, we need to reduce COD 90 %, nitrogen 30 %, phosphate 90% than that of the present value. According to these results, the water quality of sewage treatment plant is required to treat COD 13.5 mg/L, nitrogen 33.3 mg/L, phosphate 6.0 mg/L. If the sewage treatment plant will be expanded much larger in 2011, it will need to be treated in COD 6.6 mg/L, nitrogen 2.5 mg/L, phosphate 5 mg/L for the achievement of water quality standard in COD 2.5 mg/L.

There is a need to improve the efficiency of the existing sanitary treatment facilities, because the effluent standard becomes more stricter and septic sludge increased. Thus, operating processes of sanitary treatment system in M city changed with installation of additional facilities. Process modifications were as follows: Dilution water was added to the next process after primary aeration tank. Some secondary sedimentation sludge was recycled to primary aerator so that most of the organics were stabilized in primary aeration tank under automatic control of dissolved oxygen. The line of effluent from dewatering process flowing to the activated sludge tank was changed to the primary aerator. The primary sedimentation sludge line was linked to a thickener. Polymer was added to the activated sludge tank. The effluent of primary aerator and aerobic digester was recycled from the 5th to the 1st sector. As consequencies of above process modifications, the improvement of removal efficiency was achieved as BOD 54%, COD 42%, SS 61%, T-N 39%, and T-P 12%, respectively.

본 연구에서는 포항시 양덕정수장에 tracer test를 이용한 pilot plant를 설치하여 기존 플록형성지에 대한 문제점을 도출하였다. 또한 플록형성지 각단 유출부의 단면을 여러 가지 형태로 변경시키면서 수리학적 평가를 실시하였고, 그 결과 플록형성지의 각단 유출부에 대한 최적 개량단면을 제시하였고, plant에 적용하여 현재 운전중에 있다. 또한 입자의 크기별 개수를 측정할 수 있는 particle counter를 이용하여 플록형성지 개량후의 효

찌는 시간을 달리하여 절단한 차는 색과 향이 3분과 5분간을 찐 후 절단하였을 때 우수하였다. 가용성 고형분 함량, 추출 수율이 증가됨에 따라 맛의 기호성은 증진되었고, 탁도와 갈색도, 색도의 증가는 색깔의 기호성을 증진 시켰다. 3분간 찐 후 절단하여 시간별로 볶은차와 5분간 찐 후 절단하여 시간을 다르게 볶은차는 전체적 기호성이 5분간 볶았을 때 우수하였고, 가용성 고형분 함량, 추출수율, 탁도, 갈색도, 전체 색도는 볶는 시간에 비례하여 증