도로 노반의 동공 채움보수 및 지반 보강 방법으로 시멘트 혼합물을 사용한 그라우팅 보수공법이 널리 사용되고 있 다. 그러나 그라우팅의 재료로 사용되는 보통 포틀랜드 시멘트는 생산 과정에서 다량의 이산화탄소가 발생하여 환경오염 의 주요 원인으로 간주된다. 따라서 시멘트의 대체 재료로서 각종 산업부산물의 활용 가능성에 대한 연구가 활발하게 이 루어지고 있다. 본 연구에서는 도로 하부 동공 보수 및 보강용 그라우팅 재료로써, 제지 공정에서 발생하는 슬러지를 소 각하여 얻은 제지애쉬(Paper Ash)의 활용 가능성을 유변학적 관점에서 평가하였다. 제지애쉬는 보통 포틀랜드 시멘트와 화학적 조성이 비슷한 것으로 알려져 있다. 제지애쉬-시멘트 혼합물을 물-바인더 비율(W/B) 및 시멘트 치환율에 따라 유변학적 특성을 실험적으로 평가하였다. 실험 결과 제지애쉬의 특성상 100% 제지애쉬 혼합물은 유동성이 매우 낮은 결 과를 나타냈으며, 시멘트 치환율 20%까지 유의미한 유동 특선 개선 효과는 보이지 않았다. 그러나 시멘트 치환율이 20~30% 구간에서 유동성이 급격하게 개선되는 현상을 확인하였고, 30% 이상부터 추가적인 유동성 개선 효과는 미미하 였다. 또한 W/B가 높을수록 유동성은 개선되나 시멘트 치환율이 증가함에 따라 블리딩 발생량이 증가함을 확인할 수 있 었다.

Evaluation of low temperature performance of asphalt mixture is significant not only for mitigating transverse thermal cracking but also for preventing potential traffic accidents. In addition, the engineers in pavement agency need to inform the proper pavement section where urgent management is needed. Since early 2000, Korea Expressway Corporation Research Division (KECRD) developed an 3D Pavement condition Monitoring profiler vehicle (3DPM) to survey expressway pavement surface condition precisely. The management of whole expressway network became more precise, effective and efficient than before due to application of 3DPM and HPMS. One thing recommended is: performing extensive mechanical test and corresponding data analysis work procedure to further strengthen the feasibility of current 3DPM approach and HPMS. In this paper two activities were considered: first, the pavement section where the urgent care is recommended is selected by means of 3DPM approach. Then asphalt mixture cores were acquired on that specified section then low temperature fracture test: Semi Circular Bending (SCB) test, was performed. The mechanical parameters, energy release rate and fracture toughness were computed then compared. It is concluded that the current 3DPM approach in KEC can successfully evaluate and analyze selected pavement condition. However, more extensive experimental works are needed to further strengthen the current pavement analyzing approaches.

교통량이 증가하고 교량과 같은 특수구조물에 아스팔트 포장이 시공되는 사례가 증가함에 따라 일반적으로 사용되는 아스팔트보다 높은 성능을 가진 아스팔트에 대한 수요가 증가하고 있다. 일반 아스팔트 혼합물은 내구연한이 지나면 재생첨가제 등을 사용하여 다 시 도로포장재료로서 재활용할 수 있는 방안이 마련되어 있으나, 개질 아스팔트가 사용된 폐아스팔트 혼합물은 매립재로 사용하는 것 이외에는 별다른 대안이 없는 실정이다. 이에 본 연구에서는 국토부 지침에 규정된 재활용 아스팔트 혼합물 배합설계법을 적용하여 개질 폐아스팔트 혼합물을 재활용할 수 있는지를 검토해보고자 하였다. 이를 위해 개질 아스팔트를 활용하여 혼합물을 제작하였으며, 현장에서 수거되는 폐아스팔트 혼합물의 노화상태를 모사하기 위해 AASHTO R 30을 참고하여 강제 노화를 실시하였다. 노화 및 추출 과정에서 아스팔트의 물성 변화를 확인하기 위해 절대점도, DSR, MSCR 시험을 실시하였다. 시험결과, 추출 후 바인더의 절대점도는 감소하였으나 G*(복합전단계수)와 δ(위상각)은 증가하는 경향을 보였다. 소성변형 저항성을 확인하기 위해 MSCR(다중 응력 크리프 및 회복) 시험을 실시한 결과,  이 2배 가까이 증가하여 소성변형 저항성이 감소한 것을 확인할 수 있었다. 이러한 결과는 추출시 사용 되는 용매가 개질첨가제를 추출하지 못하여 기인한 결과로 판단된다. 따라서 개질 폐아스팔트 혼합물을 재활용하기 위해서는 기존과 는 다른 별도의 배합설계법이 개발되어야 할 것으로 판단되었다.

택코트란 아스팔트 포장 공사 시 기존 아스팔트층과 신설 아스팔트 층 사이에 부착성을 증가시키기 위하여 사용되는 재료이다. 교통 하중으로 인해 포장 경계면에서 수평전단응력 및 수직인장응력이 발생하게 되는데 택코트의 유실, 양생 부족 등의 문제로 접착 성능 이 부족하면 포장층의 분리, 밀림과 같은 도로 파괴가 형상이 나타날 수 있다. 현재 국내에서는 국토교통부 아스팔트 콘크리트 포장 시공 지침에 택코트 살포량에 대한 기준은 존재하지만 기존 및 신설 아스팔트 포장층 사이에 택코트의 접착강도에 대한 기준은 존재 하지 않는 실정이다, 이는 접착강도 특성이 분석되지 않은 택코트를 사용함에 따라 아스팔트 포장의 공용성 측면에서 문제를 초래할 수 있다. 따라서 본 연구에서는 PG등급이 다른 택코트 4종류에 대한 인장 및 전단접착강도를 확인하기 위하여 인장접착강도 시험, 전 단접착강도 시험을 진행하였다. 택코트의 양생정도에 따른 접착강도 특성을 확인해보기 위하여 택코트의 수분이 증발됨에 따라 중량 변화가 없는 상태를 양생 100%로 하여 양생 0%, 50%, 100%로 진행하였으며, 살포량은 국토교통부 아스팔트 콘크리트 시공 지침에 따 라 0.5ℓ/m2로 진행하였다. 사용된 택코트 종류에 관계 없이 양생 정도가 증가함에 따라 접착강도는 증가하는 추세를 보였으며, 인장 및 전단접착강도 시험에 관계없이 초기 양생(양생 0%~50%)보다 양생 50% 이후에서의 더 높게 강도가 발현된 것을 확인하였다. 또한 PG등급이 높은 택코트가 인장 및 전단접착강도에 관계없이 접착강도 성능이 우수한 것을 확인할 수 있었다. 추후 택코트의 종류를 추 가하여 PG등급이 분류가 이루어진 후에 접착강도 시험을 진행하여 결과를 확인할 예정이다.

2022년 기준 국내 폐타이어 발생량은 약 37만톤으로 그 중 88.9%인 약 32만 9천톤이 재활용되는 것으로 조사되었다. 하지만 이 중 약 75%가 시멘트소성로용 등 열이용 분야에 사용되었다. 폐타이어는 대부분 고무와 플라스틱으로 이루어져 있기 때문에, 고온에서 분 해되면서 다양한 유해가스와 오염물질이 발생할 수 있고, 이러한 공해물질은 적극적으로 관리되지 않으면 대기오염, 수질 오염 등 다 양한 환경문제를 발생시킬 수 있다. 때문에 친환경적이고 지속적인 재활용에 대한 필요성이 대두되고 있다. 폐타이어 고무 분말을 아스팔트 혼합물의 골재 일부로 치환하여 재활용하는 접근 방식은 환경에 미치는 영향을 완화할 뿐만 아니라 천연 자원의 고갈 측면에서도 긍정적인 영향을 미치는 것으로 판단된다. 따라서 타이어분말을 아스팔트 혼합물에 적용하는 것은 환경 문제를 해결하고 자원 효율성을 높이는 두 가지 이점을 가지고 있다. 폐타이어 분말을 아스팔트 바인더와 아스팔트 혼합물에 적용할 경우 미치는 영향을 평가하기 위하여 DSR, BBR, MSCR 등의 시험 을 진행하였으며, 아스팔트 혼합물 내 폐타이어 분말의 분포를 조사하기 위해 SEM을 실시하였다. 또한 IDEAL-CT와 IDEAL-Rutting 시 험을 통해 아스팔트 혼합물의 성능을 평가하였다.

본 연구는 정향, 황련 추출물을 혼합하여 Malassezia furfur에 대한 항균 능력을 확인하고 최 적의 혼합물을 만들어 항산화 및 항염증 능력을 평가하기 위해 수행되었다. 정향과 황련을 70% 에탄올, 100% 메탄올, 열수로 추출하여 항균 능력을 평가하여 정향은 100% 메탄올 추출물, 황련은 열수 추출 물이 가장 항균 능력이 높은 것을 확인하였다. 또한 두 추출물을 혼합하여 비율별로 항균 능력을 평가 하였을 때 9:1 비율이 가장 우수한 활성을 보였고 혼합물의 항산화 활성이 뛰어남을 확인하였다. Raw 264.7 세포에서 생존율에 영향을 미치지 않는 1, 10, 50, 100 μg/mL에서 LPS를 이용하여 염증 반응을 유도하고 항염증 활성을 확인한 결과 10, 50, 100 μg/mL에서 No 생성 저해율과 IL-6 발현 저해율 및 COX2, iNOS 단백질 발현 저해 활성이 뛰어남을 확인하였다. 본 연구를 통해 정향 메탄올 추출물 및 황련 열수 추출물의 혼합물은 항균, 항염증 효능이 뛰어나기에 기능성 화장품의 천연 소재로써 사용이 가능할 것으로 사료된다.

본 연구에서는 에너지 소모가 큰 기존 진공 증류 공정의 대안으로 친환경이면서 에너지 효율적인 투과증발 분리 공정을 이용하여 1,2 hexane diol/water (1,2 HDO/water) 혼합물에서 물을 분리하는 데 적용되었다. 사용한 분리막은 glutaraldehyde (GA)로 가교된 PVA를 알루미나 중공사 막(Al-HF) 내부에 코팅하여 사용하였다. 1,2 HDO/water 투과증발 분리공 정에서는 PVA/GA 비율, 경화 온도 및 투과증발 분리공정 운전 조건에 대한 막의 최적화를 연구하였다. 장기 안정성 시험에 서 PVA/GA (몰 비율 = 0.08, 경화 온도 = 80°C) 로 코팅된 Al-HF 막이 공정온도 40°C에서 1.90~2.16 kg/m2h 범위의 투과 도를 보였으며, 투과용액의 수분 함량은 99.5% (separation factor = 68) 이상이었다.

대량유살 기술을 통한 총채벌레 방제 기술이 시설 고추재배지를 중심으로 개발되었다. 이 기술의 핵심 요인은 효과적 유인제 개발에 있다. 집합페로몬에 의존하였던 유인전략은 노지 재배지에서는 뚜렷한 효과를 보이지 않았다. 따라서 본 연구는 노지 고추재배지에서 총채벌레의 대량 유살을 위해 새로운 유인물질의 추가가 필요하였다. 또한 노지재배지에서 집합페로몬의 유인력 감소 원인을 규명할 필요가 있었다. 새로운 유인 물질로서 methyl isonicotinate (MIN)이 제시되었고, 이 물질이 실내 유인행동분석을 통해 총채벌레에 대한 자체 유인력은 물론이고 집합페로 몬과 협력효과를 보였다. 이를 바탕으로 집합페로몬과 혼합물 형태로 노지 고추재배지에서 분석한 결과 총채벌레의 포획밀도를 증가시켰다. 특 히 이러한 증가는 꽃노랑총채벌레(Frankliniella occidentalis)에서 뚜렷하게 나타났다. 유인트랩에 집합페로몬의 함량 증가는 노지 고추재배지에 서 꽃노랑총채벌레는 물론이고 다른 총채벌레류의 포획밀도를 뚜렷하게 증가시켰다. 본 연구는 집합페로몬 유인력이 시설재배지와 노지재배지 사이에서 차이가 있으며, 노지 재배지의 경우 효과적 유인력을 발휘하기 위해서는 더욱 많은 집합페로몬 함량을 요구한다는 것을 밝혔다. 또한 본 연구는 집합페로몬에 MIN을 추가하여 꽃노랑총채벌레에 대한 고효율 유인제를 개발할 수 있는 기술을 제시한다.

PURPOSES : In this study, the basis for improving the maintenance method of road pavement in Jeju Island, where deterioration is accelerating, was presented through field construction and analysis of various combinations of maintenance methods. METHODS : Construction was performed on Jeju Island's Aejo Road, which has high traffic and frequent early damage, using various asphalt mixtures mainly applied in Jeju Island, with different maintenance cross-sections depending on the level of repair. The quality and performance of the asphalt mixture collected during construction were evaluated, and MEPDG was used to analyze the service life according to the type and maintenance level of the mixture. RESULTS : While the mixture for the surface layer satisfied the quality standards and had excellent rutting and moisture resistance performance, the asphalt mixture for the intermediate and base layer did not satisfy the quality standards such as air voids, so it was judged that quality control was necessary during production. The section repaired to the base layer was found to be advantageous for the integrated behavior of the pavement and had the best structural integrity. As a result of predicting the service life, the estimated life of the section where only the surface layer was repaired was analyzed to be approximately 7 years, the section where the intermediate layer was repaired was 14.5 years, and the section where the entire section up to the base layer was repaired was analyzed to be 18 years. CONCLUSIONS : In Jeju Island, where deterioration is accelerating, it was analyzed that when establishing a maintenance plan, it is necessary to consider repairing the middle and base floors in order to secure the designed life of 10 years.

PURPOSES : The aim of this study is to investigate the enhancement of performance and the mix design method for asphalt mixtures utilizing ferronickel slag, an industrial by-product METHODS : To enhance the performance of FNS asphalt, waste tire powder (CR) was incorporated, and the characteristics of FNS asphalt aggregate, along with the impact of CR, were evaluated through the mix design process. RESULTS : CR is found to be suitable with a size of 30 mesh, and the optimal usage amount is determined to be 1±0.1% of the mixture weight, considering dense grade asphalt mixture. Volumetric design considering the swelling characteristics of CR is necessary, and a mixing design with a consistent tendency can be achieved only when an appropriate VMA is secured. CONCLUSIONS : The mix design for FNS-R asphalt mixture requires an increase of approximately 1% in VMA compared to conventional dense-graded asphalt mixtures to accommodate the swelling of CR. Additionally, FNS-R asphalt exhibits improved resistance to rutting comparable to modified asphalt and meets quality standards, including stripping resistance.

PURPOSES : This study was conducted to evaluate the physical properties of the RAP 50 asphalt mixture containing polymer modified rejuvenator and warm-mix additive to improve the recycling rate of RAP and reduce CO2 emission. METHODS : Mix design of Polymer Modified Warm-mix Asphalt Mixture(RAP 50), and Hot Mix Asphalt Mixture(RAP 30) were produced and the properties of asphalt mixture such as Marshall Stability, ITS, Deformation Strength, TSR, and Dynamic Stability were compared between the two asphalt mixtures. RESULTS : The RAP 50 asphalt mixture showed superior or similar performances compared to the RAP 30 asphalt mixture in all the tests conducted. The results of the Marshall stability and dynamic stability in particular were 13,045N and 3,826 pass/mm, which were 11.37% and 76.7% greater than the RAP 30 asphalt mixture, which indicated that high plastic deformation resistance may be expected. CONCLUSIONS : The results obtained from laboratory tests on the two types of mixtures indicated that the use of polymer modified rejuvenator and warm-mix additive not only allows to increase the proportion of RAP but also improves its properties under lower temperature condition than RAP 30 asphalt mixture. Additionally, it was confirmed that plastic deformation resistance was high and moisture resistance and crack resistance were improved for a RAP 50 asphalt mixture.

PURPOSES : In this study, the resources and energy consumed to produce hot mix asphalt mixtures and hot mix reclaimed asphalt mixtures in asphalt concrete plants were estimated and the emissions from the detailed processes of the production process were evaluated based on TRACI(the tool for the reduction and assessment of chemical and other environmental impacts). METHODS : To estimate the energy consumption of the aggregate drying process, which consumes a significant amount of energy in the production process, an energy consumption calculation model based on the thermal equilibrium equation was used, and the energy consumed for material transportation, storage, and operation of other facilities was cited from the literature. RESULTS : For the system boundary conditions established and the inventory considered, the emissions to produce one ton of hot mix reclaimed asphalt mix are greater than the emissions to produce one ton of hot mix asphalt mix for a number of key impact categories. The process of producing hot mix reclaimed asphalt mixtures was evaluated to consume more resources and energy in the production of recycled aggregates and heating for drying than in the production of hot mix asphalt mixtures, but less resources and energy in the production of binders and natural virgin aggregates and the heating to heat these materials. CONCLUSIONS : The results of the emissions assessment using the life cycle inventory for the production of hot mix asphalt mixtures were generally similar to the results understood in the field and in much of the literatures, confirming the reliability of the methodology. However, in order to evaluate the dominance of specific processes or mixtures, it is believed that the construction of a wide range of inventory databases after inventory redesign is necessary for a specific and rigorous assessment.

PURPOSES : The purpose of this study is to verify the influences on the compactibility evaluation of WMA (Warm Mix Asphalt) mixture by laboratory experiments. METHODS : Two types of WMA additives (chemical and wax types) and two types of compactors (marshall and gyratory) are used in laboratory experiments. In addition, two types of WMA processes (wet and dry) are tested to verify the impact of manufacturing process. RESULTS : The laboratory results show that the effects of compaction method on compactibility are different depending on the type of additive. The compaction method has a significant impact on WMA mixture with chemical type additive to extent that it determines whether required criterion is satisfied, but only little on WMA mixture with wax type additive. In the case of wet process for WMA mixture manufacturing, it is hard to assess the air void of HMA mixture made of same asphalt binder used in WMA mixture since the additive has already been added in asphalt binder. And the test results show that air voids of HMA mixture vary within properties of asphalt binder. CONCLUSIONS : Through this study, it is found that compactibility of WMA mixture is affected by the compaction methods depending on the additive types and by the WMA mixture manufacturing process. Therefore, those are recommended to be considered when evaluating compactibility of WMA mixtures.

PURPOSES : There has been increasing interest in South Korea on warm-mix asphalt (WMA) and cold-mix asphalt (CMA) technologies that allow production of asphalt pavement mixtures at comparatively lower temperatures than those of hot-mix asphalt (HMA) for use in pavement engineering. This study aims to evaluate the feasibility of replacing HMA pavement with WMA pavement with the goal of reducing CO2 emissions associated with asphalt production for road construction. METHODS : Changes in the dynamic modulus characteristics of WMA and HMA according to short-term and long-term aging were evaluated. In addition, the effects of water damage were evaluated for short- and long-term aging stages. RESULTS : For WMA, in the process of mixing and short-term aging, early-age dynamic modulus decreased owing to low temperature and reduced short-term aging (STA) time. This could result in early damage to the asphalt pavement depending on the applied traffic load and environmental load. CONCLUSIONS : Mastercurves of the dynamic modulus were used for comparative analysis of WMA and HMA. Compared to the dynamic modulus after STA of HMA, the estimated aging time determined by experiments for WMA to achieve the required stiffness was more than 48 hours, which is equiva-lent to approximately 4 to 5 years real service life when converted. It is considered that further studies are needed for performance optimization to achieve early-age performance of the asphalt mixes.

This study aimed to determine the anti-obesity effect of adding Wolfiporia extensa Ginns (W) to fermented pollack skin products in an obesity-induced animal model. The experimental groups were the normal diet group (C), high-fat diet group (HF), dried pollack skin (H1), fermented pollack skin (H2), and W of 0.1 (F2-WL), 0.3 (F2-WM), and 0.5 (F2), respectively. It was confirmed that adding W to fermented pollack skin reduced blood triglycerides, total cholesterol, and LDL levels, while increasing HDL levels. Wolfiporia extensa Ginns was effective in controlling weight and improving blood lipids in a dose-dependent manner. In histological analysis, findings of fatty liver induced by a high-fat diet were improved by the addition of H2 and W. Size and density of fat globules in the epididymis were decreased. In addition, the concentration of TNF-α was increased in the high-fat diet group, but decreased by the addition of fermented pollack skin and W. In conclusion, adding fermented dried pollack skin and Wolfiporia extensa Ginns was effective for weight control and blood lipid improvement. Thus, the use of by-products in functional foods is expected to have a high value in the future.

PURPOSES : In this study, energy-consuming processes in asphalt plants were evaluated, and the drying and mixing processes were characterized using a thermal equilibrium equation-based model to quantitatively estimate the amount of energy consumed during the production of mixtures in asphalt concrete plants. METHODS : An energy consumption model based on the thermal equilibrium equation was used to estimate the energy consumption of the aggregate drying process that consumes the maximum energy; the energy consumed for material transportation, storage, and operation of other facilities was cited from the literature. The results were compared with the actual results obtained for recycled hot asphalt mixtures and recycled warm mix asphalt mixtures, and a sensitivity analysis was performed by varying the conditions. RESULTS : An analysis of the main processes required to produce asphalt mixtures showed that the water content had the largest impact on energy consumption (approximately 80%). This quantitatively supports the opinion of field practitioners that maximum energy is consumed during aggregate drying. Although some discrepancies were observed, the results were found to be reasonable and within the range of typical measurements. CONCLUSIONS : The thermal energy consumption estimation model provides consistent results that reflect the characteristics of the mixture and can be used to derive the thermal energy consumption rates for individual materials, such as aggregates and binders. This can be used to identify the priorities for process optimization within a plant.

PURPOSES : The evaluation of the low-temperature performance of an asphalt mixture is crucial for mitigating transverse thermal cracking and preventing traffic accidents on expressways. Engineers in pavement agencies must identify and verify the pavement sections that require urgent management. In early 2000, the research division of the Korea Expressway Corporation developed a three-dimensional (3D) pavement condition monitoring profiler vehicle (3DPM) and an advanced infographic (AIG) highway pavement management system computer program. Owing to these efforts, the management of the entire expressway network has become more precise, effective, and efficient. However, current 3DPM and AIG technologies focus only on the pavement surface and not on the entire pavement layer. Over the years, along with monitoring, further strengthening and verification of the feasibility of current 3DPM and AIG technologies by performing extensive mechanical tests and data analyses have been recommended. METHODS : First, the pavement section that required urgent care was selected using the 3DPM and AIG approaches. Second, asphalt mixture cores were acquired from the specified section, and a low-temperature fracture test, semi- circular bending (SCB) test, was performed. The mechanical parameters, energy-release rate, and fracture toughness were computed and compared. RESULTS : As expected, the asphalt mixture cores acquired from the specified pavement section ( poor condition – bad section) exhibited negative fracture performances compared to the control section (good section). CONCLUSIONS : The current 3DPM and AIG approaches in KEC can successfully evaluate and analyze selected pavement conditions. However, more extensive experimental studies and mathematical analyses are required to further strengthen and upgrade current pavement analysis approaches.