Despite the presence of the p-Channel MOSFET inrush current limiter circuit within the power supply unit of military radar, The internal MOSFET and DC-DC Converter has been damaged due to the high inrush current. In this paper, the cause of the high inrush current was identified by analyzing the p-Channel MOSFET inrush current limiter circuit. Based on the analysis, the high inrush current was reduced by about 60% by adjusting the time constant of the source-to-gate elements compared to before improvement.

선박 발전기의 여자기는 출력 단자 전압을 일정하게 유지하기 위하여 여자전류 제어를 통해 자속을 조정한다. 여자기 내부에 있는 전압제어기는 통상적으로 비례 적분 제어방식이 사용되는데 게인과 시정수에 의해 결정되는 응답 특성은 적절치 못한 설정값에 의 해 원하지 않는 출력을 내며 이로 인해 선내 전력의 품질과 안정성을 떨어뜨릴 수 있다. 본 논문에서는 IEEE에서 제공하는 AC4A 타입의 여자기 모델을 통해 얻을 수 있는 안정적인 입출력 데이터를 활용하여 신경망 회로를 학습시킨 후 기존의 비례 적분 제어방식의 전압제 어기를 학습된 신경망 회로 제어기로 대체하여 시뮬레이션을 수행하였다. 그 결과 기존 대비 최대 9.63%까지 오버슈팅이 개선되었으며, 안정적인 응답 특성에 대한 우수성을 확인하였다.

In this study, the safety aspects were studied by comparing the charge control characteristics of the two vehicles when a failure occurs between the OBC including the charging port or the charging door module (CDM) during slow charging using the In Cable Control Box (ICCB) for a long time.When the AC terminal was momentarily disconnected during charging, the Model-3 vehicle was charged normally if the AC circuit was disconnected up to three times, and the charging control was stopped when the number of disconnects reached four times. However, in the Ioniq-5 vehicle, charging control was normally performed when the disconnected AC circuit was normally connected regardless of the number of disconnection.

In the wire constituting the LIN, which is one of the vehicle communication devices, disconnection of the wire or contact resistance of the circuit occurs due to vibration and aging of the vehicle. This affects the entire communication network and may have a significant impact on the safe driving of the vehicle as information is not transmitted. In this study, a LIN BUS circuit simulator was built on its own like a real car and measured with an automotive oscilloscope instead of a common method of measuring and diagnosing a circuit with a multimeter in the event of a LIN BUS circuit failure. Referring to the experimental results, it will be possible to diagnose faults in circuits efficiently and quickly.

This study analyzes the effects of the number of angles and bends on resistance in a conductor-embroidered stitch circuit for efficient power transfer through a conductor of wearable energy harvesting to study changes in power lost through connection with actual solar panels. In this study, the angle of the conductive stitch circuit was designed in units of 30°, from 30° to 180°, and the resistance was measured using an analog Discovery 2 device. The measured resistance value was analyzed, and in the section of the angle where the resistance value rapidly changes, it was measured again and analyzed in units of 5°. Following this, from the results of the analysis, the angle at which the tension was applied to the stitch converges was analyzed, and the resistance was measured again by varying the number of bends of the stitch at the given angle. The resistance decreases as the angle of the stitch decreases and the number of bends increases, and the conductor embroidery stitch can reduce the loss of power by 1.61 times relative to general embroidery. These results suggest that the stitching of embroidery has a significant effect on the power transfer in the transmission through the conductors of wearable energy harvesting. These results indicate the need for a follow-up study to develop a conductor circuit design technology that compares and analyzes various types of stitches, such as curved stitches, and the number of conductors, so that wearable energy harvesting can be more efficiently produced and stored.

This research studied faults that may occur during slow charging using the J1772 adapter of Tesla Model-3 electric vehicles. When the AC terminal was instantaneously disconnected, charging was performed normally when an AC circuit with disconnection up to three disconnection times was connected. Charging control was suspended when the number of disconnection reached four times. However, if the AC disconnection time exceeded 22 seconds, the charging control was stopped regardless of the number of disconnection. When a contact failure occurred at the AC terminal, high surge current and noise occurred. However, when the contact improved, the charging control continued. In terms of safety, it seems necessary to take measures such as stopping charging control when detecting noise.

When the CP voltage is disconnected, the measured voltage on the ICCB side is measured to be 12V, and the voltage on the OBC side is measured to be 0V. When the PD signal was disconnected, the ICCB-side measured voltage was 0V and the OBC-side measured voltage was 4.5V. From this, disconnected position be found with the voltage value measured. When CP was disconnected for a short time, the PD voltage did not change to 1.5V, and when the PD was disconnected, the CP signal and PD signal changed to 9V, and if the CP and PD voltages were normal, the charge control could be performed normally.

선박으로부터 발생하는 배출가스에 대한 규제가 강화되고 이를 해결하기위한 대안으로 전기추진시스템의적용이 대형상선에서 부터 중ㆍ소형선박에 이르기까지 그 사용이 증가되고있다. 전기추진시스템의 효율 향상을 위한 방법으로 발전원의 개선, 배터리ㆍ연료전 지ㆍ태양광 등의 친환경 발전원의 시스템 연계 및 정류기, 전력변환장치, 추진전동기의 개발과 제어방식의 연구를 들 수 있다. 그 중 정류 방식에 있어 상천이변압기과 다이오드를 이용하는 방식이 널리 사용되었으나, 직류배전을 이용한 친환경발전원의 계통 연계, 가변속 발 전원의 사용, 중ㆍ소형 전기추진시스템의 적용을 통해 전력용 반도체 소자를 이용한 AFE정류기에 대한 수요가 증대되고 있다. 이러한 AFE 정류기를 제어하는 방식에 있어 기존의 비례적분제어기가 아닌 신경회로망을 이용한 방식을 본 연구에서는 제안하였다. 기존의 제 어기 데이터를 활용하여 Matlab/Simulink를 통해 학습한 신경회로망제어기를 설계하고 PSIM을 통해 설계된 정류시스템에 신경회로망 제어 기를 적용하여 부하변동에 따른 직류출력단의 파형과 역률 개선의 유효성을 확인하였다. 이는 공간이 협소한 중소형 친환경 선박의 정류 시스템으로써 적용이 가능하다.

In this paper, each controller's unique ID and PICO oscilloscope were used to measure the voltage waveform of each CAN communication line, and compare and analyze the serial decoding results. Using the voltage change level of the CAN communication line, it was possible to check whether the CAN-High line and the Low line were disconnected. And it was possible to infer the circuit disconnection point between the controller and the controller only with the unique ID information of each controller. And when the CAN-High circuit was disconnected, the voltage of the high line was measured at the same voltage level as the Low line.

문제적 과잉 성 행동은 성 충동과 각성을 통제하지 못하는 것과 관련이 있으며, 억제 기능을 담당하는 뇌 영역의 구조적, 기능적 변화와 관련이 있음이 밝혀졌다. 그러나 아직까지 문제적 과잉 성 행동의 휴지기 상태 시 뇌의 기능적 연결성에 관한 연구는 거의 없다. 따라서 본 연구에서는 자기공명영상장치를 사용하여 휴지기 상태 시 문제적 과잉 성 행동자의 집행 통제 회로(RECN, LECN)의 기능적 연결성의 결함을 규명하고자 하였다. 이를 위해 17명의 문제적 과잉 성 행동자와 인구통계학적 특성이 유사한 20명의 정상대조군을 대상으로 휴지기 상태 시 자기공명영상데이터가 획득하였다. 실행기능 제어 회로(LECN, RECN)와 관련된 영역을 관심 뇌 영역으로 선정하였으며, 이들 영역간 시계열 신호와의 상관계수를 기능 연결성 정도로 가정하고 집단 간 비교 검증을 하였다. 그 결과, 정상대조군과 문제적 과잉 성행동군의 집행 통제회로의 기능적 연결 강도에 유의한 차이가 나타났다. 즉, 정상대조군에 비해 문제적 과잉 성행동군은 상/중전두회와 미상핵, 상/중전두회와 두정회의 기능적 연결성이 저하된 것으로 나타났다. 또한, 이 영역간 기능적 연결강도는 과잉 성 행동 지수와 부적상관이 있는 것으로 나타났다. 본 연구 결과는 문제적 과잉 성행동자들이 성 충동과 각성을 제어하지 못하는 것이 집행 통제회로의 기능적 연결성 저하와 관련이 있음을 시사한다.

Steam tables including superheated, saturated and compressed region were simultaneously modeled using the neural networks. Pressure and temperature were used as two inputs for superheated and compressed region. On the other hand Pressure and dryness fraction were two inputs for saturated region. The outputs were specific volume, specific enthalpy and specific entropy. The neural network model were compared with the linear interpolation model in terms of the percentage relative errors. The criterion of judgement was selected with the percentage relative error of 1%. In conclusion the neural networks showed better results than the interpolation method for all data of superheated and compressed region and specific volume of saturated region, but similar for specific enthalpy and entropy of saturated region.

With the development of industrial technology and science, production and manufacturing facilities have been enhanced and improved, and the importance of the safety of workers has also been regulated and limited by various safety management methods. As a way to secure the safety of the workers from the production facility, the fail-safe and fool-proof methods are now being applied. Any possible insecure behavior and unsafe conditions can be removed by adopting the standards and specifications that are now secure the safety of workers and equipment. This research analyzes EN ISO 13849-1 international and European standards during CE certification. In order to secure acceptable reduced risks, the risk assessment process of ISO 12100 and the processes for reducing its risk are applied. In the current ISO 13849-1 standard, the criteria for the required performance level PLr (Required Performance Level) for the applicable risk and safety functions through the risk assessment are subjective and not subdivided. Therefore, the evaluation criteria are likely to cause judge’s judgement error due to qualitative judgement. This research focuses on evaluation and acceptable performance level setting for the safety circuit of the equipment. We propose an objective and specific evaluation criteria to secure safety, and the proposed evaluation criteria are applied to the case study of the safety circuit for the equipment. In order to secure the safety of the entire safety circuit, the improvement of the MTTFd and DC level related to the SRP/CS (Safety-Related Parts of Control Systems)’ lifetime is required for the future research.

Simultaneous modelling was carried out using the neural networks with three inputs including a distinguishing variable for the steam table. It covered whole steam tables including the compressed, saturated and superheated region of water. And relative errors of the thermodynamic properties such as specific volume, enthalpy, entropy were compared using the neural networks and the linear interpolation method. As a result of the analysis, The neural networks has proven to be powerful in modeling the steam table because it has slightly better results than the interpolation method.

역전기투석전지는 염수-기수의 농도차이를 원동력으로 이온교환막의 선택성에 의해 양이온과 음이온을 서로 반대방향으로 이동시켜 전력을 생산한다. 이상적인 이온교환막의 경우 35 g/L과 0.5 g/L 농도의 염수와 기수를 흘려 보냈을 때, 약 0.1 V의 전압 출력을 가진다. 본 연구에서는 역전기투석 스택전지의 출력특성에 영향을 주는 인자로서 막저항, 염수와 기수의 전기전도도, 막 이동수, 막 면적, 유로 두께 및 메쉬의 개방면적비, 스택수 등을 고려하여 수치모사를 수행하였다. 스택전지 내 유로에서 발생하는 누설전류 및 내부저항을 고려한 등 가회로모델을 수립하였고, 상용 이온교환막으로 제작된 스택전지 실험결과로부터 개방전압, 단락전류밀도, 최대전력밀도와 같은 중요 전지특성에 대하여 수치 모사의 정합성을 확인하였다.

The predictive control system using model-based predictive control is a very effective way to optimize the present inputs considering the states and future errors of the reference trajectory, but it has a drawback in that a control input matrix must be repeatedly calculated with a long calculation time at every sampling for minimizing future errors in a predictive interval. In this study, we applied the neural network simulating the predictive control method for the trajectory tracking control of the mobile robot to reduce complex control method and computation time which are the disadvantage of predictive control. In addition, the neural network showed excellent performance by the generalization even for a different reference trajectory. Therefore, The controller is designed by modeling the model-based predictive control gains for the reference trajectory using a neural networks. Through the computer simulation, the proposed control method showed better performance than the general predictive control method.

When weapon system is designed and developed, a reliability is one of important factors to determine the development goal. The reliability analysis of the weapon system and equipment is based on MIL Specification, MIL-HDBK-217F and MIL-HDBK-338B. And the weapon system is operated on various environments by operating concept of the military using the weapon system. This study, at first, present failure rate by PSA comparing with failure rates by PCM, the different reliability analysis method, for same CCA(Circuit Card Assembly). And the study present change of reliability analysis results for CCA on various operation environment condition..

Cu circuits were successfully fabricated on flexible PET(polyethylene terephthalate) substrates using wettability difference and electroless plating without an etching process. The wettability of Cu plating solution on PET was controlled by oxygen plasma treatment and SiOx-DLC(silicon oxide containing diamond like carbon) coating by HMDSO(hexamethyldisiloxane) plasma. With an increase of the height of the nanostructures on the PET surface with the oxygen plasma treatment time, the wettability difference between the hydrophilicity and hydrophobicity increased, which allowed the etchless formation of a Cu pattern with high peel strength by selective Cu plating. When the height of the nanostructure was more than 1400 nm (60 min oxygen plasma treatment), the reduction of the critical impalement pressure with the decreasing density of the nanostructure caused the precipitation of copper in the hydrophobic region.

Zermelo's navigation problem is that the ship reaches a particular target point in the minimum-time when it travels with a constant speed in a region of strong currents and its heading angle is the control variable. Its approximate solution for the minimum-time control may be found using the calculus of variation. However, the accuracy of its approximate solution is low since the solution is based on graph or table form from a complicated nonlinear equations. To improve the accuracy, we use a neural network. Through the computer simulation study we have found that the proposed method is superior to the conventional ones.

석탄회를 NaOH로 용융시킨 후 수열 처리에 의하여 제올라이트 A를 합성하였다. NaOH/석탄회의 비, 용융 온도, NaAlO2의 첨가량, 수열 처리 온도 및 시간이 생성된 제올라이트의 종류와 결정도에 미치는 영향에 대하여 연구하였다. 결정도가 높은 제올라이트의 생성에 필요한 최적의 NaOH/석탄회의 중량비는 1.2, 최적의 용융 온도는 550℃이었다. 용융된 석탄회로부터 Si4+ 와 Al3+의 용출은 교반 시간의 영향을 받지 않았다. 생성된 제올라이트의 형태는 첨가한 NaAlO2의 영향을 받는 것으로 나타났다. 적은 양의 NaAlO2를 첨가하면 제올라이트 X가 생성되나 NaAlO2의 양이 증가하면 단일상의 제올라이트 A가 생성되었다. 수열처리 시간과 온도가 증가하면 제올라이트 A는 hydroxysodalite로 변화하였다. 승온 속도를 낮춰 반응 온도까지의 도달시간을 증가시키면 결정도가 좋은 제올라이트 A를 얻을 수 있었다.