강바닥판 교량의 교면포장 재료인 구스아스팔트는 약 240 ℃ 이상의 고온에서 포설되기 때문에 강바닥판에서 100 ℃ 이상 의 온도 상승을 유발하게 된다. 강바닥판 교량은 비교적 온도 변화에 민감하기 때문에 구조물의 내구성 및 안정성에 영향을 줄 수 있으므로 수치해석을 통하여 사전에 충분히 검토하여야 한다. 강바닥판 교량의 열영향 해석기법은 단순한 온도하중을 재하하는 방법과 열원을 적용하는 방법으로 대별될 수 있다. 본 연구에서는 다양한 시공환경에 적용 가능한 열원을 산정하여 열영향 해석을 수행하고, 기존 재래식 방법인 온도하중을 부여하는 방법과 상호 비교하여 검토하고자 한다.

강바닥판 교량의 교면 포장에 240 °C 이상의 온도에서 포설 되는 구스 아스팔트 가 적용되는 경우, 구조물에 발생하는 열 영향의 검토를 수행하지만, 수치해석에 적용 가능한 열원 데이터에 대한 연구는 미흡하여 단순화된 온도 하중을 절점 하중으로 사용하고 있다. 이에 본 연구에서는 구스 아스팔트 포장 시 계측된 온도 데이터를 이용하여 비록 제한적이지만 평판요소에 직접 재하 가능한 열원 방정식을 구성하여 제시하였으며 간략한 수치해석을 통해 그 타당성을 확인하였다.

In case of applying Guss asphalt concrete on steel deck of suspension bridges, the weight of the pavement may lead to a change in cable tension and a inclination of the main tower. And when the construction speed is high or excessive application width is applied it, a high temperature rise occurs at a large area at a time, and demage due to thermal deformation or excessive local stress may be induced in bridge members. In this study, we present a case study of the thermal effect on the structure behavior of the site by numerical analysis.

This paper presents the influence factors of heat transfer in a voided slab under fire situation. The effects of a void in a slab on heat transfer are presented and the results are quantitatively analyzed for each influence factor. For this purpose, the finite element analysis method was used to evaluate the influence of the heat transfer factors on the thermal characteristics in a voided slab. Based on these results, the influence factors which have significant difference in the temperature spectrum were derived.

The quality characteristics of ‘Xiangshui’ pears (Pyrus ussuriensis) treated with different concentrations of biomass pyrolysis liquid (BPL) during storage at 25℃ were investigated. The weight of ‘Xiangshui’ pears treated with BPL declined at a slower rate than that of the control. The rot index of BPL-treated ‘Xiangshui’ pears decreased with increasing storage times, and treatment with 20-fold-diluted BPL resulted in the lowest rot index after storage for 12 days. The total acid content of ‘Xiangshui’ pears treated with 20-fold-diluted BPL was 0.19%, and was the highest after storage for 12 days. After storage for 12 days, the total sugar content of ‘Xiangshui’ pears treated with 20-fold-diluted BPL was 7.19%; this was significantly higher than that of the control, but not significantly different from that of pears treated with other BPL dilutions. The vitamin C content of ‘Xiangshui’ pears showed a decreased trend, and pears treated with 20-fold-diluted BPL had a vitamin C content of 2.21 mg/100 g after storage for 12 days and showed the least decline compared to other treatments. In addition, respiration in ‘Xiangshui’ pears was effectively inhibited by treatment with BPL. In conclusion, BPL treatment exerts a protective effect on the quality of ‘Xiangshui’ pears during storage, with 20-fold-diluted BPL being the most effective.

Since the late 20th century, the urbanization in Korea has been rapidly increasing, especially in major cities like Seoul, as a result of industrialization. One of the aspects of urbanization is coating the surfaces with impervious concrete or asphalt that water cannot penetrate. In addition, various urban, such as urban heat islands, which also have a great impact on the urban environment, occur within the cities. Therefore, the urban environment is gradually becoming hot and dry, and the need for more urban parks to compensate for these negative impacts is growing. Thus, several numerical studies have been conducted to assess these problems using coupled Numerical Weather Prediction (NWP) and Computational Fluid Dynamics (CFD). In this study, an experiment was conducted to determine the accuracy of the area of the input field using Weather Research and Forecasting (WRF) model, and applying the more accurate input field to a numerical simulation using ENVI-met, in order to investigate the effect of urban parks on the thermal comfort. The results showed that an input field with a larger area is more accurate than that with a smaller area, because the surrounding terrain and cities are considered in details in the experiment with the larger area. Subsequently, the more accurate input field was used in ENVI-met, and the results of this simulation showed that the presence of the urban park increased the thermal comfort and improved the humidity conditions.

This study sought to determine the changes in weather conditions in urban streets, along with conditions of traffic and roads in urban areas. The variations in weather conditions depending on traffic differed according to distance. First, the temperature difference measured by traffic results is as follows: T1 point 1.03℃ , T2 point 1.04℃ , T3 point 0.9℃ , T4 point 1.01℃ , and T5 point 0.31℃ . The average difference between the measured temperatures by the point of measurement was 0.86℃ . The changes in wind velocity according to traffic volume results of the measurements is T1 point 1.32 m/s, T2 point 0.80 m/s, T3 point 0.29 m/s, T4 point 0.04 m/s, and T5 point 0.09 m/s. The difference between the average wind speeds was 0.51 m/s and traffic jams caused substantial differences in distance. The relative humidity tended to be inversely proportional to temperature. The measurements results ares T1 point 2.29%, T2 point 2.67%, T3 point 2.47%, T4 point 2.16%, and T5 point 0.91% The difference between the average relative humidity was 7.3%. In case of independent sampling T test according to traffic volume, changes in wind velocity and temperature were directly proportional to the level of statistical significance(p<0.01). On the other hand, relative humidity tended to be inversely proportional; however, there was no statistical significance.

Recently, production of sewage and wastewater sludge have increased sharply with the population density and related industrial activity. As a result, studies of sludge treatment and reduction have been conducted and a pre-treatment method that uses thermal hydrolysis has emerged as a solution to this problem. To address problems with the thermal hydrolysis pre-treatment process, the deaeration and nitrogen recovery processes have been set up together, thus generating factors that inhibit dewaterability. In this study, the effect of pre-treatment, deaerated sludge on dewaterability-inhibiting factors (pH, temperature, aeration rate) was evaluated and alternative solutions were prepared. First, the dewaterability improvement effect increased rapidly at 190°C or higher when thermal hydrolysis pre-treatment was applied. Then, 1 L of thermal hydrolysis pre-treatment reactants at 190°C were injected into 1, 5, and 10 L/min air flows at 50°C, but no significant difference in capillary suction time (CST) or time to filter (TTF) was found. The dewaterability improved when the temperatures of the pre-treatment reactants varied between 30, 50, and 70°C under aeration at 5 L/min. However, when the pH was increased to 7, 9, or 11 at 5 L/min and 50°C, the dewaterability worsened by at least 10 times relative to the hydrolysis pre-treatment reactants. The zeta potential decreased from -30 mV to -50 mV as the pH increased. Thus, the stabilities and dispersities of the reactants increased due to the repulsive force of the particles. This was confirmed to be the cause of poor dewaterability. A coagulant can be used to solve to this problem, or the deaeration process can be placed after solid-liquid separation and the heat of thermal hydrolysis can be extracted via heat exchanger.

An insulating brick was developed and evaluated as a potential recycling Waste Limestone (WL) with Melting Slag (MS). We aimed at analyzing the parameters affecting the insulating brick manufacture to enhance the recyclability of WL. In this study, The thermal conductivity, compressive strength and apparent porosity of prepared brick were measured with the addition of aluminum dross and the molar ratio of the alkali activator. The thermal conductivity, compressive strength and apparent porosity were 0.28 W/mK, 2.41 MPa and 44.72% respectively at a mixing ratio of 9.5 : 0.5wt%, 1.5 M SiO2/Na2O, 3wt% aluminum dross. Thus, it met the standards of insulating fire bricks (KS L 3301).

강바닥판은 콘크리트 바닥판에 비해 강성이 작아 차량의 윤하중에 의해 국부적으로 큰 변형이 발생하여 포장표면에 인장응력을 유발시켜 포장균열 발생의 원인이 된다. 또한, 용접이음부의 포장이 균일한 두께로 포설되지 않거나 강바닥판과 아스팔트 포장 사이의 부착성 부족으로 인해 공용 중 포장손상이 발생한다. 최근 이러한 문제점을 해결하기 위해 강바닥판 교량에 구스 아스팔트와 같은 부착성 및 내구성이 우수한 특수 아스팔트 포장을 실시하는 경우가 늘고 있으나 구스 아스팔트는 일반 아스팔트 보다 약 100℃정도 높은 고온상태에서 포설되기 때문에 강바닥판의 온도가 100℃~130℃ 정도 상승하게 된다. 이와 같은 온도상승은 포장 시공 중 강바닥판의 변형을 유발하고 포장 완료 후에도 강바닥판 교량의 품질에 악영향을 미친다. 이에 본 연구에서는 구스 아스팔트 포장온도가 강바닥판의 열변형에 미치는 영향을 검토하여 강상판 교량의 시공상에 문제점이 되고 있는 포장문제를 해결하고자 하였다. 해석결과, 지점과 교각의 2개의 교량받침과 Shear key가 설치되어 구스아스팔트 포장 시공 도중 문제시 되고 있는 지점의 부반력에 의한 받침의 들림이나 신축이음의 영향, 교축방향 변위의 영향은 모두 허용치 범위 내에 있는 것으로 나타났다. 또한, 보부재에 모델링된 U-리브, 종형 및 횡형의 단부부재에 발생하는 응력은 강바닥판 또는 평판에 발생하는 응력에 비하여 작은 것으로 나타났다.

Onion (Allium cepa L.) is one of the richest sources of flavonoids in human diet. Onion peel contains over 20times more quercetin than onion flesh. In this study, we studied the effects of onion peel water extract (OPE) on the bloodlipid profiles in mice. The onion peel extracts was extracted with hot water. The experimental groups were divided with 3groups (n=6) of ICR male mice: normal diet+distilled water (NC), high-fat diet+distilled water (HF), high-fatdiet+onion peel water extract 20㎎/㎏ (OPE-20). The oral administration was conducted daily. The experimental periodwas 7 weeks. Onion peel water extract showed higher concentration of polyphenol gallic acid and anti-oxidant trolox equiv-alent than the ethanol extract. The body weight gain and food efficiency ratio was significantly lower in the OPE-20 group ascompared with HF group (p<0.05). The epididymal fat and retroperitoneal fat showed significantly lower weights and sizesin the OPE-20 group as compared with HF group (p<0.05). The serum levels of total cholesterol, LDL cholesterol and trig-lyceride were significantly lower in the OPE-20 group as compared with HF group (p<0.05). The OPE-20 group showedhigher HDL cholesterol concentration than HF group (p<0.05). Atherogenic index was ignificantly lower in as comparedwith HF group (p<0.05). The serum levels of glucose, GOT and GPT were significantly lower in the OPE-20 group as com-pared with HF group (p<0.05). In these results, we suggests that onion peel water extracts supplementation can reduces theserum lipid components and improves the lipid metabolism in hyperlipidemic mice induced with a high-fat diet.

방사선을 조사한 시료를 가열하면 시료로부터 흡수된 에너지의 일부가 더 긴 파장의 빛으로 방출되는 것을 이용한 것이 열형광선량계이다. 본 연구의 목적은 피폭선량계로 널리 이용되는 8개의 TLD-100에 동일한 조건에서 열처리와방사선을 조사하여 자기장을 노출하지 않은 4개와 자기장에 노출시킨 4개를 글로우 곡선을 분석 하였다. 실험 결과방사선 조사로 포획된 전자가 자기장 노출에 의해 낮은 트랩의 전자들 중 일부는 가전자대의 정공과 결합하여 48%의피크 면적이 감소하였다. 낮은 트랩의 면적 감소로 인하여 자기장에 노출된 TLD-100은 낮은 선량을 나타내었다. 또한 낮은 트랩의 활성화 에너지는 1.6 eV와 1.5 eV로 나타났다.

In this study, the thermo-catalytic hydrogenation using corn stark and wasted palm kernel shell was carried out for the production of hydrocarbon compounds in direct biomass liquefaction. The conversion of biomass in direct biomass liquefaction over Mo-based catalyst increased with increasing the reaction temperature and the content of the volatile matter contained in biomass and the corn starch was more available than the wasted palm kernel shell. And then, the conversion was about 97.9% using corn starch and was about 92.4% using wasted palm kernel shell at 400oC. It was confirmed that the liquefied products obtained after the thermo-catalytic reaction were C6, C7, C8-typed hydrocarbon compounds.

Chloride binding capacity in cementitious materials is a crucial factor for service life prediction of marine concrete. C-S-H phase have significant physical binding capacity for chloride ions. In this study, specific surface area of C-S-H with various Ca/Si ratio was measured. This study suggested effective way to compute maximum adsorption of bound chloride by C-S-H based on theory single molecular layer. In addition, surface potential is very important as a main mechanism for chloride binding adsorption. Thus, intrinsic equilibrium constant was obtained and surface potential of C-S-H was calculated in chemical equilibrium solution by means of PHREEQC. Based on the experiment results, to develop integrated system for prediction of chloride binding behaviors is final goals.

This study forecasts changes in thermal environment and microclimate change per new building construction and assignment of green space in urban area using Computational Fluid Dynamics(CFD) simulation. The analysis studies temperature, humidity and wind speed changes in 4 different given conditions that each reflects; 1) new building construction; 2) no new building construction; 3) green spaces; and 4) no green spaces. Daily average wind speed change is studied to be; Case 2(2.3 m/s) ＞ Case 3. The result of daily average temperate change are; Case 3(26.5℃) ＞ Case 4(24. 6℃) ＞ Case 2(23.9℃). This result depicts average of 2.5℃ temperature rise post new building construction, and decrease of approximately 1.8℃ when green space is provided. Daily average absolute humidity change is analysed to be; Case 3(15.8 g/kg') ＞ Case 4(14.1 g/kg') ＞ Case 2(13.5 g/kg'). This also reveals that when no green spaces is provided, 2.3 g/kg' of humidity change occurs, and when green space is provided, 0.6 g/kg change occurnd 4(1.8 m/s), which leads to a conclusion that daily average wind velocity is reduced by 0.5 m/s per new building construction in a building complex.

터널에서 외기에 접촉되는 부분은 입, 출구부와 환기구가 있으며 이러한 부위의 열화와 그 진행속도는 외기의 영향을 받지 않는 구간과는 다른 차이를 보여준다. 실제로 터널에서 외기에 접촉되는 부분뿐만 아니라 외기의 영향을 받는 구간은 일반적인 구간과는 다른 관점에서 접근해야 할 필요가 있고 보수나 보강공법 적용시에도 우선 고려가 되어야 한다. 그럼에도 불구하고 터널의 유지관리시, 점검 및 정밀안전진단시 외부온도의 영향을 받는 구간의 결함 및 열화는 그 범위가 광범위함에도 불구하고 구조체의 안전성에 미치는 영향이 미소하다는 이유로 소홀히 되고 있는 실정이며 일시적인 계절영향, 온도 변화요인에 의한 것으로 판단하여 특별한 관리가 되지 않고 있는 실정이다. 이에 본 논문은 외부온도, 기온의 터널내 영향범위를 산출하기 위해 2개소의 도심지 터널에 대해서 적외선 열화상카메라를 활용하여 터널내의 외부온도 영향범위를 결정하고 그 영향범위에서 발생되는 콘크리트라이닝 또는 콘크리트 구조체의 결함 및 열화원인을 분석하고 유지관리시 중점을 두고 시행해야 할 사항을 제시하였다.

The present study explores time and spatial thermal environment for Daegu, which is a city built on a basin area, according to varying land cover conditions of the earth's surface by analyzing data derived from meteorological observation and satellite images. The study has classified land use by utilizing MODIS satellite images and analyzed land surface temperature. Also, by using data acquired from automatic weather system, the study has evaluated the effects of atmospheric heating caused by city pavements by analyzing the sensible heat flux between the city's land surface and the atmosphere.The results are as follows. 1) Classification of land use in the Daegu area shows 46.64% of urban and built-up area, 1.39% of watersides, 35.19% of forest, 11.43% of crops, and 5.37% grasslands. 2) During the weekdays throughout the year, the land surface temperature was high for Dalseogu, Bukgu, and Seogu regions where industrial complexes could be found. Comparatively, lower temperature could be observed in the woodlands. 3) While the land surface temperature displayed the effects of pushing air upwards during the weekdays in urban areas, the reverse was true for forest regions. During the night, the temperature did not exert any significant influence on air movement.