In this study, the design of parking brake mounting bracket for SUVs (sports utility vehicles) was handled through structural analysis. For safety evaluation, we conducted a shape analysis of parking brake mounting bracket, discovered improvement measures for weak areas, and reflected them in the design. In addition, a strength analysis was performed and the analysis results were reflected in the design. As a result of analysis through various design changes, it was possible to suggest an appropriate parking brake mounting bracket shape. In addition, the effect of changes in the shape of the reinforcement and mounting bracket on the stiffness and strength of the parking brake mounting bracket was investigated.

We introduce the technology required todevelop a bracket process for installing and verifying FRT bumper sensors for passenger cars. Establish and demonstrate process automation through actual design and manufaturing. We conduct quality inspection of the production process using artificial intelligence and develop technology to automatically detect good and defective products and increase the reliability of the process

본 논문에서는 다이나믹크리깅 대리모델 기반 자동차 브레이크 패드 마모량 측정센서 브라켓의 설계최적화를 소개한다. 브레이크 작동시 마찰재 바닥의 온도가 600°C 이상으로 상승하고, 이 열이 전달되어 센서의 기능을 상실시킨다. 따라서 열전달을 최소화하는 브라켓 형상의 설계최적화는 필수적이다. 최적화에 소요되는 계산비용을 절감하기 위해 다이나믹크리깅 대리모델로 열전달 시뮬레 이션을 대체하였다. 다이나믹크리깅은 최적의 상관함수와 기저함수를 선정하였으며, 정확한 대리모델을 도출하였다. 최적화 결과 센 서위치의 온도가 초기모델에 비해 7.57% 감소하였으며, 이를 열전달 시뮬레이션으로 다시 한번 확인하여 대리모델 기반 최적설계가 유의미함을 검증하였다.

In recent years the tunnel construction is increasing worldwide because of development of science and technology and increasing of transportation demand. Tunnels are complex structures normally rectangular cross section or semicircular and constructed to connect between different sections of roads. Because of the importance, the construction and extension of road tunnels are also continuously increasing along with the development. According to data from the Korea Expressway Corporation, the number of road tunnels, which was 1,332 in 2010, increased rapidly by about 2.1 times over 10 years to a total of 2,742 in 2020. The extension of road tunnels is also on the trend of increasing, with a total of 945 km in 2010 reaching 2,157 km in 2020. The benefits of a double-deck tunnel are emphasized, particularly in terms of construction cost and convenience. This tunnel design incorporates a central slab, dividing the tunnel into upper and lower spaces. The versatility of a double-decker tunnel is evident in its ability to accommodate various uses for both levels. For instance, the upper level can function as vehicle roads, while the lower level can be designated for train tracks. In this study, the effect of RWS and modified hydrocarbon fire curve was applied to the concrete tunnel bracket through simulation to analyze the temperature after the fire occurrence.

This study aims to examine the cutting traces remaining on the bracket tie beams of Sungnyemun gate, identifying the tools employed during the late Goryeo to early Joseon periods by specific processes, and deliberating on the timber shaping techniques utilized in advanced architectural construction during the late Goryeo to early Joseon eras. Through the research, it was confirmed that in the production of Sungnyemun Gate's bracket tie beams during the 14th to 15th centuries, both the timber splitting and ripsawing methods were used in conjunction. Moreover, the wood finishing process revealed the use of a plane. It can be inferred that the characteristics of the plane used during that time were not significantly different from those observed in the later period of the Joseon dynasty. The ripsawing and plane finishing techniques were evident in various parts of the bracket tie beams of Sungnyemun gate across the reigns of king Taejo and Sejong, indicating that the techniques involving ripsaw and plane were already prevalent in the late Goryeo period. Consequently, it can be inferred that the ripsawing and plane finishing techniques might have been applied in the construction of prominent government buildings in Hanyang(Seoul), including Gyeongbokgung Palace, and in the residences of royalty and nobility after the establishment of the Joseon dynasty.

In this study, computer simulation of the drawbridge structure was performed to verify the validity of the design and to evaluate its safety. For this, the follower bracket was modeled, and the parts of the follower bracket were connected using 1D elements. The boundary condition applied moments to the rotation shaft of the girder gear in the clockwise and counterclockwise directions, and the connection between the upper parts was modeled using 1D elements to model the bolted connection. In case of rotational shaft deformation, an analysis was performed on the displacement occurring in the structure during the opening/closing operation. As a result of structural analysis of the follower bracket for various cases, the stress at the connection was lower than the tensile strength and yield strength, so it was evaluated as safe. Through this, we intend to use it as a data that can identify anomalies.

As the demand for aesthetic orthodontic treatment increases, the use of self-ligating ceramic brackets is increasing. For stable treatment, there should be no fracture or deformation of the self-ligation ceramic bracket door. Therefore, considering the situation in which labial displacement of teeth occurs in the orthodontic treatment stage. For this study, a model of the mandibular anterior region of a ceramic self-ligating bracket with a passive sliding door mechanism was selected. The measured tensile force data was substituted into the simulation analysis conditions, and the tensile force, stress distribution, and deformation values were analyzed using the finite element method. Using this, it is able to use the design elements of the orthodontic bracket that should be considered as design inputs in the development stage.

Jukseoru is a pavilion building located in 44 Jukseoru-gil, Samcheok-si, Gangwon-do. Jukseoru is characterized by the fact that the center 5 bays out of the front 7 bays are in the form of Jusimpo, while the ends of each side are in the form of an Ikgong. In addition, the columns are not aligned with each other because the columns of both compartments are out of the center rather than the columns of the center of the five compartments of the columns do not match each other. Based on this, architectural historical circles initially built five bays in pairs, but later added one space to each side to make it seven bays. Recently, however, a new claim has been made that it was built with seven bays from the beginning. Therefore, this paper proved that Jukseoru were expanded through historical data. We also looked at the characteristics of the Jukseoru period and the process of transformation through comparison of the bracket type.

This paper examines the seismic performance and structural design of the ceiling bracket-type modular connection. The bracket-type system reduces the cross-sectional area loss of members and combines units using fitting steel plate, and it has been developed to be fit for medium-story and higher-story buildings. In particular, this study conducted the cyclic loading test for the performance of the C-type and L-type brackets, and compared the results. The test results were also compared with the commercial FEA program. In addition, the structural design process for the bracket-type modular connection was presented. The two connections, proposed as a result of the test results, were all found to secure the seismic performance level of the special moment steel frame. In the case of initial stiffness, the L-type bracket connection was found to be great, but in the case of the maximum moment or fully plastic moment, it was different depending on the loading direction.

In Korean traditional architecture, the Gong-po style is divided into the Jusimpo, Dapo and Ikgong. Jusimpo and Chulmok-Ikong, where only Gong-po is placed on the column, differ in form of Gong-po depending on the viewpoint. Since ‘Chulmok-Ikgong’ has been generally regarded as ‘One Chulmok-Two Ikgong’, the precedent researches have been conducted mainly on ‘One Chulmok-Two Ikgong’ in the Gong-po style classification. However, when it comes to ‘One Chulmok’, the style of Ikgong can be organized from the one to three steps and this study is particularly for examining the occurrence and transformation of ‘One Chulmok-One Ikgong’. One of the case study sites, Bonghwa Cheongamjeong was originally built in the 16th century, and is believed to have been repaired from ‘Non Chulmok-One Ikgong’ to ‘One Chulmok-One Ikgong’. Since the beam linked directly to the upper part of a capital, it does not connect the eave trave(architrave) in between. Also, Soro which supports Jangyeo(the architrave strip) has been placed and linked in comparatively lower position. It is confirmed by the signigicant difference in the hierarchy of Gong-po forms in one architecture. The Jeonju-Hyanggyo Daeseongjeon, which was built in the 17th century among the subjects, was similar with ‘One Chulmok-One Ikgong’, but it was found to be the type of Jusimpo form because the bottom of the beam and the top of the Ikong are apart. And Gongan is confirmed at Cheomcha. In the 17th century, it can be seen that Heot-Cheomcha disappeared and Ikgong was started to use as a constant figure. The end of the 18th century, it can be seen that it was changed into a ornament added on Haeng-gong, being seen in the case of Hwaseong Dongjangdae. In conclusion, it can be seen that ‘One Chulmok-One Ikgong’ were developed in both the Jusimpo and Ikong style. The transformation into ‘One Chulmok-One Ikgong’ was inevitable consequence related with an elevation difference between the eave trave and the column trave.

The purpose of this study is to improve the durability by solving the crack problem of the steering gearbox bracket welded to the frame assembly. For the exact and effective analysis, we use charac- teristic(fishbone) diagram from the viewpoint of 4M1E. Through this analysis it was identified two kinds of problems, and develop improvement plan for it. Verification tests must be performed to confirm the improvement. So, the test method for steering gearbox bracket improvement was newly established by referring to similar case. As a result of the tests for verification, the stresses at crack point are decreased and the durability was improved about 2.6 times compared with product before improvement.

The stiffness of a bicycle frame is a major factor of a bicycle performance related to safety, stability, and weight. In this study, the torsional and bottom bracket stiffness of a bicycle frame were experimentally investigated. The torsional and bottom bracket stiffness for 63 bicycle frames were evaluated and analyzed by measuring the displacement of frames. The torsional stiffness is related with turning performance and the bottom bracket stiffness is related with power transmission. The experimental results show that the average stiffness varies up to 20 % according to the frame materials and types. The torsional stiffness has a strong corelation with the bottom bracket stiffness even though they have different effects on a bicycle frame. It seems that the experimental results can be applied to the quality criteria of racing bicycles and also design standard of a bicycle frame.

There were lots of changes of the wooden structure in the middle of Joseon Dynasty. It was the time of replacement from Jusimpo (simple bracket system) to Ikgong (wing-like bracket system) and each bracket had shown mutual variation as well as itself. The aspects of change were discovered that the decorative elements of Ikgong and Dapo (multi-bracket system) had accepted from each other. It was clearly shown that not only the Ungung (carved cloud-shape) and Chotgaji (shape of the acuminate leaf) of Ikgong had affected to Dapo, but also Gaang (pseudo-pointing cantilever) of Dapo had affected to Ikgong. It was mostly found in the Buddhist architecture because there was the conservatization of ruling hierarchy as well as the active growth of Buddhist society.

Dental brackets are widely used by the orthodontists to correct the misalignment of teeth in the mouth over a long period of time. In this study, finite element analysis of orthodontic bracket has been carried out for the observation of the stress distribution and deformation pattern in the different materials bracket (Stainless Steel, Ceramic, Titanium, Polycarbonate and Nitinol) when subjected to arch wire torsion and tipping force. The simulation results were further optimized with respect to bracket attachment surface. It was found that it is possible to know the change in result is correlated with the attachment surface of the stress and deformation due to change in diameter. The results confirmed that the finite element method has proved to be successful for proper design analysis for future development of the teeth bracket.