A fixed-point iteration is proposed to integrate the stress and state variables in the incremental analysis of plastic deformation. The Conventional Newton–Raphson method requires a second-order derivative of the yield function to generate a complicated code, and the convergence cannot be guaranteed beforehand. The proposed fixed-point iteration does not require a second-order derivative of the yield function, and convergence is ensured for a given strain increment. The fixed-point iteration is easier to implement, and the computational time is shortened compared with the Newton–Raphson method. The plane-stress condition is considered for the biaxial loading conditions to confirm the convergence of the fixed-point iteration. 3-dimensional tensile specimen is considered to compare the computational times in the ABAQUS/explicit finite element analysis.

The rear door of the wheeled armored vehicle is a part that provides a passage for the crew to get on and off when it is opened and plays a role in forming watertightness and airtightness when it is closed. A case where the rear door was deformed during the rear door opening/closing operation occurred. The rear door should be improved because when it has been deformed, it is impossible to form watertight and positive pressure so that damage for humans and repair cost may occur. Therefore, in this paper, the causes of deformation were analyzed, and improvement plans were derived in order to prevent the deformation of the rear door of wheeled armored vehicles. In addition, a verification test was conducted to evaluate the appropriateness of the improvement plans.

This paper analyzed the correlation between injection molding factors through correlation analysis. In addition, the decision-tree model, which is a white box model with excellent explanatory power, was used to obtain optimal molding conditions that satisfy multiple constraint conditions. First, 243 data to be used in the experiment were created through a full factorial design. Second, a correlation analysis was conducted to understand the correlation. Third, to verify the decision-tree model, the prediction performance was evaluated using RMSE. As a result, good prediction performance was confirmed. A decision-tree experiment analysis was conducted. As a result of the progress, the same results as the correlation analysis were derived. Based on the previous analysis results, optimal molding conditions were applied to CAE. As a result, the amount of deformation in the multi-cavity could be improved by about 1.1% and 2.72% while satisfying the constraint.

The design of the corner joints in furniture structures is very important to firmly support the loaded structure and to sufficiently maintain the durability and stability. Therefore, the strength of the corner joints and the rigidity of the connected panels play a very important role in the structural performance of the assembled furniture. The structural properties can be measured or calculated experimentally or numerically, and compared by representing the applyed forces or bending moments as a function of deformed value. This paper shows the numerical models to determine the strength and stiffness of the 3-types of corner joints for simple designed furniture. Based on the finite element results, the maximum stresses are concentrated on the corner joints designed with MDF panels. And the deformation resistances and maximum applied loads are calculated for furniture corner joints under tensile and compressive moment.

본 논문에서는 CAD 시스템에서 사용하는 NURBS 기저함수를 사용하는 아이소-지오메트릭 해석(Isogeometric analysis) 방법과 기 하학적으로 엄밀한 빔 모델링(geometrically exact beam model)을 활용하여 회전과 병진 운동이 결합된 새로운 형태의 메타물질 (metamaterial)에 대한 해석을 진행하였다. 이차원 셀 구조는 자유형상변환(Free-form deformation) 법과 적절한 내삽법(Interpolation) 을 통해 원통 위에 입혀졌다. 원통의 치수와 셀 개수가 비틀림 각도에 미치는 영향이 매개변수 연구(parametric study)를 통해 확인되었 다. 비틀림과 병진 운동이 결합된 구조의 메커니즘에 대해 수치 예제를 통해 알아보았다.

In this study, in order of to reflect the mold deformation in the injection molding process to design of mold, the mold deformation was analyzed by performing flow and structural analysis. The 5 inch LGP(light guide plate) mold, platen and tie bar were modeled and applied to the analysis. The result of melt pressure from flow analysis was extracted for use as boundary conditions acting on the mold surface in the structural analysis. In order to evaluate the accuracy of simulation analysis results, injection molding was performed under the process conditions of simulation. As a results, the mold deformation during injection molding tends to be similar that of injection pressure, and it is confirmed that it shows the behavior and properties of melt resins. Compared with the simulation and experiment, the error of the maximum mold deformation in the injection phase was 4.20%.

목적 : 도수와 안경테의 다른 변수의 변화가 없는데 새로운 안경을 착용하였을 때 불편함을 느끼는 사람을 대상 으로 안경테와 렌즈에 따른 변수를 분류하여 왜곡정도, 커브변화, 어지러움에 미치는 영행을 알아보고자 하였다. 방법 : 도수와 안경의 변수의 변화가 없고 안과적 질환 및 다른 질환이 없는 성인남녀 103명(남자55명 여자48 명) 206안을 대상으로 안경테(재질, 모양, 가공방식)와 안경렌즈별(굴절률, 설계방식, 코팅종류)로 변수를 분석하여 그 변수들이 렌즈의 왜곡정도, 커브변화, 어지러움증에 미치는 영향을 측정하였다. 결과 : 렌즈에 따른 분류에서는 굴절률, 코팅방식에서 왜곡정도, 커브변화, 어지러움의 차이가 있는 것을 확인하 였다. 안경테에 따른 분류에 재질, 안경테의 모양, 가공방식에서 왜곡정도, 커브변화, 어지러움의 차이가 있는 것을 확인하였다. 왜곡정도, 커브변화, 어지러움의 상관분석 결과 어지러움은 상관분석 결과 안경이 왜곡정도 심하면 심할 수록 커브변화가 더 커지는 것을 확인하였고 안경의 왜곡정도가 심하면 심할수록 어지러움 정도가 더 심해지는 것을 확인하였으며. 어지러움은 상관분석 결과 안경의 커브변화가 클수록 어지러움 정도가 더 심해지는 것을 확인하였다. 결론 : 본 연구 결과 사용된 안경테와 렌즈에 따라 왜곡정도, 커브변화, 어지러움에 대한 차이가 나타났다. 따 라서 이를 고려한 안경테와 렌즈의 선택과 그에 맞는 가공이 필요하다고 사료된다.

In this study, the flat glass and adsorption pad were modeled using SolidWorks Simulation, to understand the deformation characteristics of the vertical flat glass by the adsorption pressure during vertical transport of LCD. The horizontal and vertical displacements and equivalent stresses of the flat glass were investigated by the structural analysis. From the displacement and stress visualization according to the adsorption pressure, the higher the adsorption pressure, the larger the glass surface protruded. The horizontal deformation of flat glass increased with increasing thickness and the vertical deformation increased with decreasing thickness. In addition, the maximum equivalent stress applied to the flat glass increased significantly as the adsorption pressure increased and the thickness decreased. As a result of the structural analysis, the thinner the thickness of the plate glass, the greater the effect on the adsorption pressure. Especially, the effect of the adsorption pressure was clearly observed at the thickness of 0.5mm.

일반적인 구조용 강재의 경우 항복변형률의 이상의 변형을 경험한 이후에 하중을 제거하면 재가력되는 시점에 따라 서 재료의 항복강도는 증가하고 연성이 감소하는 현상을 보인다. 원형강관의 경우 철판을 말아서 제작하는 과정에서 철판의 두 께와 원형강관의 직경에 따라서 항복변형률이상의 큰 변형을 경험하게 되고 이러한 변형은 제작된 강관의 구조적인 성능에 많 은 영향을 미친다. 이러한 이유에서 제작과정에 발생하는 변형이 원형강관의 구조성능에 미치는 영향을 파악할 필요가 있다. 따 라서, 이 연구에서는 원형강관을 제작하는 경우에 발생하는 변형에 의한 철판의 항복강도, 인장강도 및 연성 등의 영향을 파악 하기 위해서 강관의 직경 및 두께와 시험편을 채취한 방향을 변수로 다수의 인장실험을 수행하고 이를 분석하였다. 실험 결과 를 바탕으로 원형강판에서 채취한 시험편은 코일에서 채취한 시험편에 비해 항복강도와 인장강도가 더 높았고, 연신율은 낮아 진 것으로 나타났다.

In this paper, we investigated the change of sectional shape according to the tension when the reed wire was rolled. When rolling is performed, the tension acting on the reed wire acts in the opposite direction of the rolling progress and prevents twisting or bending phenomenon. The shape of the cross section was changed according to the tension acting on the reed wire, and the reed wire was rolled by continuously rolling the flat rolled wire and the tension was applied to the reed wire to control the simulation. As a result of the experiment, it was confirmed that the dimensions of the thickness and width after rolling can be adjusted through the tension acting on the lead wire. It was also confirmed that as the tension increased, the length of the lead wire increased and the residual stress increased.

In this study, analysis on the stiffness of the headrest, the stiffness of front-rear load and the torsion of cushion frame was performed using finite element method in order to investigate the properties of the stress-deformation by material characteristics according to the test requirements of FMVSS (Federal Motor Vehicle Safety Standard). The results are shown that AZ31 (Mg alloy) and A365 (Al alloy) with low modulus of elasticity and density have higher strain rate than steel in terms of stress-deformation and meet the standards for safety within 108 mm of the maximum amount of deformation. Considering it’s safety and durability, however, the selection of AZ31 for light weight seems difficult to gain the reliability because it causes an excessive deformation, and therefore it is not expected to be used for recliner where stress is concentrated and also the bracket linking rail and cushion frame.

Orthodontic is important to apply the optimal orthodontic force. The orthodontic bracket is deformed and the stress caused by tension and torsion of the wire. In this study, using the ANSYS the material that is currently widely used in orthodontic bracket material of stainless steel, ceramic, titanium, polycarbonate, by applying the nitinol analyzed the strain and the stress distribution on the bracket side. Simulation results on the stress distribution and deformation, and it was found a difference of each material.

본 논문에서는 현재 시공중인 58층의 철근콘크리트조 고층건물에서 진동현식게이지를 통해 계측된 기둥의 축방향 변형률과 레이져 스캐닝을 통해 구한 횡변위를 3차원 시공단계해석에 의한 예측치와 비교하였다. 예측치는 ACI 209와 PCA의 재료모델식, PCA report의 축소량 산정알고리즘을 3차원 구조해석 프로그램으로 개발한 ASAP을 사용하여 구하였다. 비교결과 평면의 중앙부 기둥의 축방향 변형율 계측치는 시공단계 해석치와 거의 유사한 결과를 나타내었으나 각 모서리에 두 개씩 배치된 기둥의 경우 비교적 큰 오차를 나타내었다. 레이져 스캐닝에 의한 횡변위 계측결과는 해석결과와 유사한 경향을 보였으나 층당 계측치가 큰 변동을 나타내므로 향후 이를 해결하기 위한 계측 및 데이터 처리기법이 요구된다.

Newmark-type deformation analysis has rarely been done in Korea due to the popularity of simple pseudo-static limit equilibrium analysis and detailed time-history FE/FD dynamic analysis. However, the Korean seismic dam design code updated in 2011 prescribes Newmark-type deformation analysis as a major dynamic analysis method for the seismic evaluation of fill dams. In addition, a design PGA for dynamic analysis is significantly increased in the code. This paper aims to study the seismic evaluation of four existing large fill dams through advanced FEM/Newmark-type deformation analyses for the artificial earthquake time histories with the design PGA of 0.22g. Dynamic soil properties obtained from in-situ geo-physical surveys are applied as input parameters. For the FEM/Newmark analyses, sensitivity analyses are performed to study the effects of input PGA and Gmax of shell zone on the Newmark deformation. As a result, in terms of deformation, four fill dams are proved to be reasonably safe under the PGA of 0.22g with yield coefficients of 0.136 to 0.187, which are highly resistant for extreme events. Sensitivity analysis as a function of PGA shows that PGA30cm (a limiting PGA to cause the 30 cm of Newmark permanent displacement on the critical slip surface) is a good indicator for seismic safety check. CFRD shows a higher seismic resistance than ECRD. Another sensitivity analysis shows that Gmax per depth does not significantly affect the site response characteristics, however lower Gmax profile causes larger Newmark deformation. Through this study, it is proved that the amplification of ground motion within the sliding mass and the location of critical slip surface are the dominant factors governing permanent displacements.

In this paper, an efficient yet accurate method for the thermal stress analysis using a first order shear deformation theory(FSDT) is presented. The main objective herein is to systematically modify transverse shear strain energy through the mixed variational theorem(MVT). In the mixed formulation, independent transverse shear stresses are taken from the efficient higher-order zigzag plate theory, and the in-plane displacements are assumed to be those of the FSDT. Moreover, a smooth parabolic distribution through the thickness is assumed in the transverse normal displacement field in order to consider a transverse normal deformation. The resulting strain energy expression is referred to as an enhanced first order shear deformation theory, which is obtained via the mixed variational theorem with transverse normal deformation effect(EFSDTM_TN). The EFSDTM_TN has the same computational advantage as the FSDT_TN(FSDT with transverse normal deformation effect) does, which allows us to improve the through-the-thickness distributions of displacements and stresses via the recovery procedure. The thermal stresses obtained by the present theory are compared with those of the FSDT_TN and three-dimensional elasticity.

본 연구에서는 GaN 나노와이어의 인장, 압축, 하중 제거 전산모사를 분자동역학 방법을 통하여 수행하였고, 평형 분자 동역학 방법인 Green-Kubo 방법을 이용하여 각각의 변형된 구조의 나노와이어의 열전도율을 구하였다. 단면의 형상이 육 각형이고, 길이 방향이 [0001] 격자 방향으로 형성된 나노와이어에 인장 하중이 작용하게 되면 나노와이어의 원자 구조는 초기의 wurtzite 구조에서 정방정계 구조로 변형된다. 초기 상태에 압축 하중이 작용하는 경우에는 상변이 현상은 나타나 지 않는다. 압축에서 인장으로 변형률이 증가함에 따라 나노와이어의 열전도율은 감소하는 경향을 나타낸다. 이 같은 열전 도율의 변화는 변형률에 따른 포논의 감쇠시간 감소에 의한 것이다. 인장에 의해 변형된 정방정계 구조의 나노와이어에서 인장 하중을 제거하는 경우에는 초기의 wurtzite 구조로의 역상변이 현상이 나타나고, 이와 같은 역상변이 과정에 wurtzite 구조와 정방정계 구조가 동시에 나타나는 중간 단계가 존재한다. 중간 단계의 열전도율은 같은 변형률에서 wurtzite 구조 일 때보다 낮은 특성을 갖는다. 내부 원자 구조에 따른 열전도율의 차이는 구조적 변형에 의한 포논의 군속도 변화에 따른 것이다.

The air blowers for fuel cell electric vehicle usually have big difference between inlet and outlet pressure. When the casing of the air blowers is designed, the stress analysis is required. (Approximately Inlet pressure is 0.5bar and outlet pressure is 2bar.) Gap distance between the casing and the impeller is 0.3mm. Therefore, if the amount of maximum deformation of casing is larger than 0.3mm, impeller crashed the casing. In order to avoid crashing, both the thickness and number of rims are changed and carried out simulations on each cases.

This study investigated tensile deformation of the stress aging heat-treated SM45C steel which are aging temperature at 250℃ and 300℃; aging time at 1 hour and, 3 hours; applied load at 300N and 400N by using an acoustic emission techniques (AEs). A signal processing technology is applied to evaluate an AE source characterization of different AE measurement systems DiSP & PCI-2. In this study, most suitable aging condition appeared at 250℃, 3 hours and 300N. But in cases of 250℃, 3 hours, 400N and 300℃, 3 hours, 400N conditions, yield load decreased compare to other conditions according to the over-aging phenomena. On the other hand, when arranged via AE amplitude results by K-means clustering pattern recognition of AE raw signals, tendency of signal strength appeared non-heat treatment condition, 'Class 1 < Class 2 < Class 3'; optimal condition, 'Class 3 < Class 2'; over-aging condition, 'Class 3 < Class 2 < Class 1'. This is judged by emitting a lot of AE energy when material causes plastic deformation because ductility increases on factor by over-aging phenomenon.