Spent ion exchange resins have been generated during the operation of nuclear facilities. These resins include radioactive nuclides. It is needed to fabricate them into a stable form for final disposal. Cement solidification process is a useful method for the fabrication of them into a waste form for final disposal. In this study, proper conditions for the fabrication of them into a stable waste form were determined using the cement solidification process. In-drum waste forms were then produced at the conditions, where the stability of representative samples was evaluated for final disposal. The samples were satisfied to the Waste Acceptance Criteria for low and intermediate level radioactive waste disposal sites. This result can be utilized to derive optimal conditions for the fabrication of spent ion exchange resins into a final disposal form.

In KAERI, the nuclide management technology is currently being developed for the reduction of disposal area required for spent fuel management. Among the all fission products of interest, Cs, I, Kr, Tc are considered to be significantly removed by following mid-temperature and hightemperature treatment, however, a difficulty of real spent-fuel thermal treatment experiment limits the development of such thermal treatment. The test employing SimFuel (Simulated Spent Fuel) can be an alternative for such condition, however, the fabrication of SimFuel containing semivolatile species such as Cs, I and Re (substitute for Tc) was not achieved for conventional sintering method since such species are easily removed during hot temperature treatment. In this study, for the prevention of volatilization of such species and the inclusion of semi-volatile species in fabrication of SimFuel, argon-based high pressurizing up to Max 100 bar was considered to be applied in high temperature treatment. For this, lab-scale hot-isostatic press applicable up to 1,500°C was fabricated and is being waiting for the approval for high-pressure test. After approval of license, UO2 baesd SimFuel containing CsI will be fabricated and its micro-structure and composition will be evaluated through SEM-EDX and XRD

As part of strengthening pyro safety measures, the Korea Atomic Energy Research Institute is developing LIBS (Laser-Induced Breakdown Spectroscopy) application technology to analyze molten salt components in electrolytic recovery device in real time. LIBS performs qualitative and quantitative analysis by analyzing the spectrum of energy emitted by atomizing and ionizing elements on the surface of a salt sample with a high-focused laser. Since salt easily corrodes metal, it must be managed in an environment with a dew point of -40°C or lower. In this study, we designed and manufactured a device that places a rod-type sampling stick on a mounting base, automatically moves it to the optimal measurement position for LIBS, and retrieves the sample. Its characteristics are as follows. First, LIBS is stationary and does not move. Second, the sample stick is placed on a mounting base and can rotate 360 degrees. Third, according to the command, the sample stick automatically moves to the optimal measurement position of LIBS with three degrees of freedom (X, Y, Z). Fourth, the salt attached to the sampling stick is recovered for chemical analysis by driving the gripper mounted at the bottom of the Z axis, Z axis, and rotation axis (R). The X, Y, and Z movement distances of this device are each 100 mm, rotation is 360 degrees, grip stroke is 50 mm, and position accuracy is ±20 m. Once the performance test of the automated salt sample analysis device is completed, it will be installed in a dry room with a dew point of - 40°C or lower. Samples will be collected remotely in connection with the electrolytic recovery device and gantry robot built in the dry room. We plan to conduct experiments to seat the sample stick. Ultimately, we plan to conduct comprehensive experiments in conjunction with LIBS.

On a global scale, the storage of spent nuclear fuel (SNF) within nuclear power plants (NPP) has become an important research topic due to limited space caused by approaching capacity saturation. SNF have e been collected over decades of NPP operation, coming up to capacity limitation. In case of Korea, every reactor except Saeul 1 and 2 has reached a SNF storage saturation rate of over 75%. One of the most studied methods for enhancing storage capacity efficiency involves increasing storage density using racks with neutron absorbers. Neutron absorbers like borated stainless steel (BSS) are utilized to manage the reactivity of densely stored SNF. However, major challenges of applying BSS are manufacturing hardness from heterogenous microstructure and mechanical property degradation from helium bubble formation. This study suggests that innovative fabrication methods of 3D printing can be good candidate for easier fabrication and better structural integrity of BSS. Directed energy deposition (DED), one of the 3D printing methods have become major candidate method for various alloys. It deposits alloy powder on base melt surface by high intensity laser, similar with welding process. Powder manufacturing is already demonstrated superior performance compared to casting in ASTM-A887, such as increased mechanical properties, owing to its well distributed chemistry of alloy. Moreover, as its original microstructural property, the formation of micro-pores through DED could lead to long-term performance improvements by capturing helium generated from the neutron absorption of boron. The potential for fabricating complex structure is also among the advantages of DED-produced neutron absorbers. Expected challenge on DED application on BSS is lack of printing condition data, because the 3D printing process have to be kept very careful variables of thermal intensity, powder flux and etc. These processes may get through much of trial & error for initial condition approaching. Nonetheless, as a recommendation of improved neutron absorber for efficient SNF pool storage, the concept of 3D printed BSS stands out as an intriguing avenue for research.

Refined structured tin dioxide gets the amount of attraction because of its low cost and stability. The C@SnO2 nanospheres with mesoporous structures were produced using the hard template method in this work. The C@SnO2 is primarily gained attributed to the dehydration condensation of C6H12O6 and the hydrolysis of SnCl4 ·5H2O. The morphology of the C@SnO2 was analyzed by physical characterization and the diameter of the obtained C@SnO2 was around 138 nm. When C@SnO2 was applied to lithium-ion batteries as anode material, it performed outstanding electrochemical properties, with a capacity of 735 and 539 mA h g− 1 maintained at 1000 and 2000 mA g− 1, respectively. Furthermore, it exhibits favorable discharge/ charge cycle stability. This is probably because of the more chemically redox active sites provided by C@SnO2 nanocomposites and it also allows fast ion diffusion and electron migration.

Molybdenum-tungsten (Mo-W) alloy sputtering targets are widely utilized in fields like electronics, nanotechnology, sensors, and as gate electrodes for TFT-LCDs, owing to their superior properties such as hightemperature stability, low thermal expansion coefficient, electrical conductivity, and corrosion resistance. To achieve optimal performance in application, these targets’ purity, relative density, and grain size of these targets must be carefully controlled. We utilized nanopowders, prepared via the Pechini method, to obtain uniform and fine powders, then carried out spark plasma sintering (SPS) to densify these powders. Our studies revealed that the sintered compacts made from these nanopowders exhibited outstanding features, such as a high relative density of more than 99%, consistent grain size of 3.43 μm, and shape, absence of preferred orientation.

본 연구에서는 공기중에서도 안정적이며 상대적으로 전기음성도가 큰 테플론계열의 고분자와 그래핀플라워를 이용하여 마찰전기 나노발전기를 제작하였다. 상기 복합고분자는 회전도포방법을 이용하 여 나노발전기의 전기적 음성층의 제작에 이용되었다. 전기적 양성층을 위하여 졸-겔 방법을 이용하여 산 화아연막을 제작하였다. 제작된 마찰전기 나노발전기는 약 44 μW의 최대전력을 생산하였다. 결론적으로, 마찰전기 나노발전기의 모든 활성층은 회전도포방법을 이용하였으므로 대면적으로 확장가능하다.

Inorganic-organic composites find extensive application in various fields, including electronic devices and light-emitting diodes. Notably, encapsulation technologies are employed to shield electronic devices (such as printed circuit boards and batteries) from stress and moisture exposure while maintaining electrical insulation. Polymer composites can be used as encapsulation materials because of their controllable mechanical and electrical properties. In this study, we propose a polymer composite that provides good electrical insulation and enhanced mechanical properties. This is achieved by using aluminum borate nanowhiskers (ABOw), which are fabricated using a facile synthesis method. The ABOw fillers are created via a hydrothermal method using aluminum chloride and boric acid. We confirm that the synthesis occurs in various morphologies based on the molar ratio. Specifically, nanowhiskers are synthesized at a molar ratio of 1:3 and used as fillers in the composite. The fabricated ABOw/epoxy composites exhibit a 48.5% enhancement in mechanical properties, similar to those of pure epoxy, while maintaining good electrical insulation.

This study aims to prepare a colloidal silica-containing powder to enhance the solubility and dissolution rate of rivaroxaban using a self-nanoemulsifying drug delivery system (SNEDDS). We investigate the impact of colloidal silica on a nanoemulsion system for preparing powdered SNEDDS. The liquid SNEDDS comprises 30/20/50 (w/w/w) Peceol/ Cremophor RH40/Tween 80, which results in the formation of the smallest droplets. Three powdered SNEDDS formulations are prepared by suspending the liquid SNEDDS formulation using colloidal silica and spray drying. The powdered SNEDDS prepared with liquid SNEDDS and colloidal silica at a ratio of 1/0.5 (w/w) exhibits the highest water solubility (0.94 ± 0.62 vs. 26.70 ± 1.81 μg/mL) and dissolution rate (38.4 ± 3.6 vs. 85.5 ± 3.4%, 45 min) when compared to the drug alone. Morphologically, the liquid SNEDDS is adsorbed onto colloidal silica and forms smaller particles. In conclusion, an SNEDDS containing rivaroxaban, prepared using colloidal silica, facilitates the creation of a nanoemulsion and enhances the water solubility of rivaroxaban. Accordingly, this technology holds significant potential for commercialization.

Porous ceramics are used in various industrial applications based on their physical properties, including isolation, storage, and thermal barrier properties. However, traditional manufacturing environments require additional steps to control artificial pores and limit deformities, because they rely on limited molding methods. To overcome this drawback, many studies have recently focused on fabricating porous structures using additive manufacturing techniques. In particular, the binder jet technology enables high porosity and various types of designs, and avoids the limitations of existing manufacturing processes. In this study, we investigated process optimization for manufacturing porous ceramic filters using the binder jet technology. In binder jet technology, the flowability of the powder used as the base material is an important factor, as well as compatibility with the binder in the process and for the final print. Flow agents and secondary binders were used to optimize the flowability and compatibility of the powders. In addition, the effects of the amount of added glass frit, and changes in sintering temperature on the microstructure, porosity and mechanical properties of the final printed product were investigated.

The focus of this paper was on the establishment of a service design model for digital fabrication. Service design processes and tools were used to identify problems of current digital fabrication systems. Augmented reality was deployed to substantiate two-dimensional information by combining it with digital fabrication equipment to enhance interactivity and engagement. The fuzzy Delphi method was used to consult the expert’s opinions to optimize the model for increasing overall system satisfaction. A two-dimensional quality questionnaire was designed to survey the participant’s opinions on the system’s satisfaction. The result indicated that the participants reacted positively to augmented reality and the service design model. The result of this paper was helpful for the exchange and diffusion of digital knowledge to strengthen people’s interaction with information. It can improve the efficiency of entire value chains, including product development, marketing and service, which is crucial to future innovative design and fabrication practice.

For decontamination and quantification of trace amount of tritium in water, an efficient separation technology capable of enriching tritium in water is required. Electrolysis is a key technology for tritium enichment as it has a high H/T and D/T separation factors. To separate tritium, it is important to develop a proton exchange membrane (PEM) electrolyzer having high hydrogen isotope separation factor as well as high electrolyzer cell efficiency. However, there has not been sufficient research on the separation factor and cell efficiency according to the composition and manufacturing method of the membrane electrode assembly (MEA) Therefore, it is necessary to study the optimal composition and manufacturing method of the MEA in PEM electrolyzer. In this study, the H/D separation factor and water electrolysis cell efficiency of PEM electrolyzer were analyzed by changing the anode and cathode materials and electrode deposition method of the MEA. After the water electrolysis experiment using deionized water, the D/H ratio in water and hydrogen gas was measured using a cavity ring down spectrometer and a mass spectrometer, respectively, and the separation factor was calculated. To calculate the cell efficiency of water electrolysis, a polarization curves were obtained by measuring the voltage changes while increasing the current density. As a result of the study, the water electrolyzer cell efficiency of the MEA fabricated with different anode/cathode configurations and electrode formation methods was higher than that of commercial MEA. On the other hand, the difference in H/D separation factor was not significant depending on the MEA fabrication methods. Therefore, using a cell with high cell efficiency when the separation factor is the same will help construct a more efficient water electrolysis system by lowering the voltage required for water electrolysis.

The dry storage of spent fuel has become an increasingly important issue in the field of nuclear energy. Square-gridded baskets have been widely used for the storage of spent fuel because of their superior heat transfer and structural integrity. In this paper, we review the fabrication process of square-gridded baskets for dry storage of spent fuel. The review includes the design considerations, material selection, manufacturing methods, and quality control measures. We also discuss the challenges and opportunities for further improvement in the fabrication of square-gridded baskets. The fabrication of square-gridded baskets is a critical process for the safe and reliable dry storage of spent fuel. The review of the fabrication process highlights the importance of design considerations, material selection, manufacturing methods, and quality control measures. Continued efforts to improve the fabrication process will help to ensure the safe and secure storage of spent fuel.

Molten Salt Reactor (MSR) is one of Generation-IV nuclear reactors that uses molten salts as a fuel and coolant in liquid forms at high temperatures. The advantages of MSR, such as safety, economic feasibility, and scalability, are attributed from the fact that the molten salt fuel in a liquid state is chemically stable and has excellent thermo-physical properties. MSR combines the fuel and coolant by dissolving the actinides (U, Th, TRU, etc.) in the molten salt coolant, eliminating the possibility of a core meltdown accident due to loss of coolant (LOCA). Even if the molten salt fuel leaks, the radioactive fission products dissolved in the molten salt will solidify with the fuel salt at room temperature, preventing potential leakage to the outside. MSR was first demonstrated at ORNL starting with the Aircraft Reactor Experiment (ARE) in 1954 and was extended to the 7.4 MWth MSRE developed in 1964 and operated for 5 years. Recently, various start-ups, including TerraPower, Terrestrial Energy, Moltex Energy, and Seaborg, have been conducting research and development on various types of MSR, particularly focusing on its inherent safety and simplicity. While in the past, fluoride-based molten salt fuels were used for thermal neutron reactors, recently, a chlorine-based molten salt fuel with a relatively high solubility for actinides and advantageous for the transmutation of spent nuclear fuel and online reprocessing has been developing for fast neutron spectrum MSRs. This paper describes the development status of the process and equipment for producing highpurity UCl3, a fuel material for the chlorine-based molten salt fuel, and the development status of the gas fission product capturing technologies to remove the gaseous fission products generated during MSR operation. In addition, the results of the corrosion property evaluation of structural materials using a natural circulation molten salt loop will also be included.