In this study, the shape evaluation and design of the spare tire carrier for SUV (sports utility vehicle) were addressed through structural analysis. Spare Tire Carrier analysis was conducted to evaluate rigidity, and strength and improvement measures for appropriate shapes were found and reflected in the design. Through structural analysis of the spare tire carrier, this study was conducted to derive an optimal design plan as the stiffness and strength needed to be increased for stable installation of the spare tire carrier. Compared to the existing model, the bar, which was curved, was changed to a straight line to shorten the length, thereby increasing rigidity. In addition, because the moment was concentrated in the structure of the rear hanger mounting bracket, the side part of the bracket was extended, but the cross member stiffness was relatively weak, so it did not have a significant effect.

In this study, the shape evaluation and design of clamp mount for SUVs (sports utility vehicles) was dealt with through structural analysis. The clamp mount analysis was performed to evaluate stiffness, strength and improvement plans for appropriate shape were found and reflected in the design. In addition, strength analysis and was performed in parallel to solve the problem of rib design around the edge part of the clamp mount and the thickness effect results were reflected in the design. As a result of analysis through various design changes, it was possible to present an appropriate reinforcement design shape. In addition, when the thickness of the fuel tank was changed from 3.2mm to 4.0mm, the stiffness of the fuel tank decreased by approximately 30%, and reinforcement was required.

Decarbonization plays an important role in future energy systems for establishing a zero-carbon society. Hydrogen is believed to be a promising energy source that can be converted, stored, and utilized efficiently, leading to a broad range of possibilities for future applications. Hydrogen can be stored in various forms, including compressed gas, liquid hydrogen, hydrides, adsorbed hydrogen. Among these, liquid hydrogen has high gravimetric and volumetric hydrogen densities. There are a lot of previous studies on thermal behavior of MLI and VCS and optimization insulation system, but research on the insulation performance by varying the head shape of the tank has not been conducted. In this study, thermal-structural coupled analysis was conducted on the insulation system with VCS positioned between two layers of MLI for a liquid hydrogen storage tank. The analysis considered dome shapes (torispherical, circle, ellipses), and heat flux and temperature were derived from thermal analysis to predict insulation performance. Maximum equivalent stress and deformation were calculated from the structural analysis, and the optimal dome shape was proposed.

In this study, a prefabricated buckling brace (PF-BRB) was proposed, and a test specimen was manufactured based on the design formula for the initial shape and structural performance tests were performed. As a result of the experiment, all standard performance requirements presented by KDS 41 17 00 and MOE 2021 were satisfied before and after replacement of the reinforcement module, and no fracture of the joint module occurred. As a result of the incremental load test, the physical properties showed a significant difference in the stiffness ratio after yielding under the compressive load of the envelope according to the experimental results. It is judged necessary to further analyze the physical properties according to the experimental results through finite element analysis in the future.

In this work, we deal with the feasibility of structural topology optimization for beam designs using retrofits that optimally allocates the reinforcement to the web under the condition that designers set bolt regions for H-beams of different dimensions. Mean compliance or minimal strain energy is considered for the optimization. Volume fraction is given to the design space to assign appropriate steel material quantities. The purpose of this study is to evaluate optimal shapes of stiffeners with the maximum rigidity that improves the axial and shear performance of the H-beam and to satisfy a given safety design standard of H-beam and stiffeners in case arbitrary load effect and resistances. Finally, the effectiveness of stiffness-based topology optimization on stiffeners is verified with several practical applicable examples.

본 논문에서는 구조물의 부분 변위값으로 전체 구조물의 변위 형상을 예측할 수 있는 인공지능 학습기법을 개발하였으며, 개발된 기술의 성능을 실험을 통해 평가하였다. 3차원 공간에서 변위 형상 및 노드 위치 좌표의 특성을 학습에 반영할 수 있는 Image-to-Image 변위 형상 학습과 위치 특징을 결합한 변위 상관 학습 방법을 제시하였다. 개발된 인공지능 학습방법의 성능을 평가하기 위해 목업 구 조 실험을 진행하였고, 3D 스캔으로 측정한 변위값과 인공지능으로 예측한 결과를 비교하였다. 비교 결과 인공지능 예측 결과는 3D 스캔 측정 결과에 비해 5.6~5.9%의 오차율을 보여 적정 성능을 보였다.

The purpose of this study was to develop a side protection device for school buses for children. In the case of the door side impact beam, it plays a very important role because it protects passengers from external collisions. However, in the case of a school bus for children, the space between the door and the door trim is very narrow, unlike a general passenger car. So, as an alternative to this, we are trying to develop Rub Rail, which is compulsory for children's school buses in the United States. Based on the results of structural analysis according to the cross-sectional shape of the rub rail, we want to find out the appropriate shape of the rub rail.

In this study, to improve the performance of kitchen range hoods, a comparative analysis of air volume and noise is conducted using three ducts by changing shapes. It was found that the difference in air volume was caused by the pressure difference received by each shape. The noise data can be found to be no more than 60dB overall, except for the second tier of A-type. The difference when connecting the circular, square, and flexible ducts was judged to be due to some laboratory noise, and it was found that there was no difference.

최근 비구조요소의 피해사례가 증가하면서 비구조요소 내진설계에 관한 많은 연구가 진행되고 있다. 하지만 대부분의 연구는 평면 적 요소보다는 수직적 요소나 시스템적 요소를 변수로 층가속도를 평가하고 있다. 때문에 본 논문에서는 횡력저항에 많은 부분을 차 지하는 코어를 평면적 변수로 사용하여 비구조요소 내진설계를 위한 층가속도에 대해 평가하였다. 정사각형의 2축대칭의 평면에서 코어의 형태(위치 및 비중)변화에 따라 서로 다른 5개의 평면과 각 평면마다 5층, 10층, 15층, 20층의 층수를 가진 총 20개의 모델로 선 형시간이력해석을 수행하였다. 분석 결과 코어 위치에 따라 편심을 받는 평면에서는 층가속도가 최대 1.7배의 비틀림 증폭이 발생하 였고 구조물의 중층부에서 비틀림의 영향이 가장 큰 것을 확인할 수 있었다. 편심이 없이 코어의 비중만 변화한 평면에서는 주기 0.4694초를 기준으로 이하일 때는 주기가 증가할수록 층가속도가 저층부에서는 감소하고 고층부에는 증가하며, 반대로 주기 0.4694 초 이상일 때는 주기가 증가할수록 층가속도가 저층부에서는 증가하고 고층부에는 감소한다는 것을 확인할 수 있었다. 또한, 구조물 의 층수는 최대층가속도에 영향을 주지 못하는 것을 확인하였다. 핵심용어 :

High concentrations of fine particles are increasingly being detected due to inflows from abroad and local emission sources in Korea. As most people spend about 90% of their time indoors, the use of indoor air cleaners has grown significantly as they are now thought to be essential items. In this study, the noise, power consumption, and clean air delivery rate (CADR) of commercial air cleaners were analyzed according to the structural shape of the air cleaners. Analyses were performed based on the experimental results of 249 cases for air cleaners certified by Korea Air Cleaning Association. The air cleaners with front inlet and upper outlet air flow direction, which currently account for the highest market share, were found to have the highest noise per CADR (dB(A)/(m3/min)). On the other hand, the air cleaners with the inlet and outlet air flow in the same horizontal direction were found to have lowest noise per CADR than other structures.

구조물 환기성능 평가에서 기존 사용된 환기 지표 (ACH: Air Change per Hour)는 유체가 거동하는 구조물 내 유량의 흡·배기량과 전체 볼륨에 의해 결정된다. 이는 구조물 내 유체 유동 중 국부적으로 정체된 흐름을 평가하는 지표로 사용하기 부적합하다. 본 논문에서는 구조물에서 국부적으로 정체된 흐름을 정량적으로 나타내기 위해 역류량을 이용하여 새로운 지표 (κ: 역류량 지수)를 제안 하고, 구조형상 변수에 의해 국부적으로 정체된 유체 흐름을 평가한다. 유체 흐름 영향인자로 구조형상 변수는 공극비 (ρ), 공극 개수 (N)로 선정한다. 전산 유체 역학 (CFD)에 의한 해석 결과, 구조형상 변수에 의한 자연 환기 성능은 유사하지만, 공극의 유무에 의한 국부 정체 기류의 크기에는 차이가 발생함이 나타난다. 또한, 역류량 지수는 구조형상 변수 각각 감소함에 따라 값이 증가하는 경향이 나타난다. 본 결과를 바탕으로 회귀분석을 통해 공극비과 공극 개수 변수에 의한 역류량과 역류량 지수의 근사값이 제시된다.

In this study, we compare and analyze stress and vertical deflectional displacement according to cross sectional shape changes of the beam using finite element analysis. The 11,000mm long horizontal beam showed stress differences depending on the cross-sectional variation, with stress differences of up to 200MPa and at least 149MPa. The deflection at the end of the beam also differed by up to 586 mm and at least 208mm. The weight change applied according to the cross-sectional shape of the steel horizontal beam was up to 235kgf, at least 144kgf, and showed the best stress and deflection characteristics in the cross sectional shape with a weight of 185kgf. This allowed us to improve structural safety through sectional shape optimization despite the weight increase.

In this study, the structural analyses were conducted for each model by applying the loads into the design of a large commercial truck seat. Model C with three vertical frames has the smallest total deformation among all models, indicating the strongest stiffness. The maximum total deformation of model C was shown to be 0.68 times smaller than that of model A and 0.79 times smaller than that of model B. The equivalent stress of model C was also shown to be the lowest, indicating the greatest stiffness. The maximum equivalent stress of model C was shown to be 0.8 times smaller than that of model A and 0.91 times smaller than that of model B. At the upper part of the seat or the part where the force was applied, all three models were shown to have the largest total deformations and equivalent stresses. If the result of this study is applied to the design of automotive seat frame, it is thought that the durable and rigid sheets can be manufactured efficiently. By utilizing this study result, the equivalent stress and total deformation are investigated without the real experiment by shape at the seat of large commercial truck, and the durability and rigidity can be seen.

In this study, the deformation, equivalent stress and strain energy were analyzed on the electric kick board emerging as a new means of transportation at the accident of a front collision according to each shape were analyzed. The largest part deformation happened at the handle, and the board part where the person’s feet was placed was seen to become weak. The equivalent stress was most visible at the board section, unlike the deformation results. In particular, the deformation and stress of model A which has a long and thin neck, have occurred greatly. Therefore, the longer the neck, the greater the deformation and stress occur. Among all models, the deformation and stress were the smallest at model C. As model A has a particularly thinner neck and board connection part, a large strain energy appeared. Therefore, it is considered that the connection needs to be reinforced thickly and firmly. On the study result, the thicker the board part of the electric kick board and the lower the body of the vehicle, the safer it is. The results of this study can be effectively applied to investigate the values of stresses and deformations, and strain energies through structural analysis without the fracture test at the front collision according to the shape of electric kick board.

In this study, the structural and fatigue analyses were carried out according to the shape of the self-made car frame. As a result of structural analysis, all models are shown to have the weak strength and large deformation, as the equivalent stress increases at the forward part of the impact force. It can be seen that model 3 is deformed less than other models 1 or 2. And model 3 with the truss structure prevents the great deformation from the collision. In case of irregular fatigue loads, the fatigue life of the ‘Sample history’ increased by about 59.3 times compared to the ‘SAE bracket history’ under extreme fatigue load conditions, indicating that the fatigue load condition of the ‘Sample history’ were stable. The fatigue life and deformation of model 3 among all models are significantly different to models 1 and 2. If the research results are applied to the design of self-made cars, it will be useful for improving the durability and preventing the damage. The results of this study can be effectively utilized to investigate the values of stresses and deformations, and fatigue lives without the experiments of fracture and fatigue according to the shape of the car frame.

앵커채널은 건축 외장재 등을 쉽고 안정적으로 고정하는데 적합하여 철근콘크리트 구조물의 연결 구성요소에 적용되고 있다. 선설치 앵커채널은 천공 중 콘크리트 보강재를 손상시키지 않으며, 현장용접 등에 의한 손상을 최소화 하는 장점이 있다. 본 연구에서는 원형앵커와 I형 앵커를 적용한 앵커채널의 인장 및 전단 거동을 실험적으로 평가하였다. 연단거리 및 피복철 근 및 앵커형상에 따른 앵커채널의 인장 및 전단강도 평가를 위하여 인장 및 전단실험을 실시하였다. 시험 결과, 원형앵커의 인장강도는 I형 앵커보다 증가하는 경향이 나타났다. 그리고 콘크리트에 매립된 앵커의 기하학적 형상, 피복철근 유무 및 연단거 리에 따라 비교한 결과, I형 앵커의 전단강도가 원형앵커보다 약 55% 낮은 것을 알 수 있었다.

보이지 않는 힘으로도 불리는 잠수함은 수중에서 활동하는 은밀성을 장점으로 대함전, 대잠전 및 핵심표적 타격 등의 임무를 수행하는 전략 수중 무기 체계로 심해에서 높은 수압을 견디며 작전을 수행할 수 있어야 한다. 이러한 관점에서 잠수함 압력 선체는 잠항 깊이에 상응하는 외부 수압에 저항하는 가장 중요한 체계로서 누수, 화재, 충격 및 폭발과 같은 위험으로부터 안전성을 확보함으로써 생 존성을 높임과 동시에, 작전 수행 능력을 유지할 수 있게 해주는 강도를 확보하고 있어야 한다. 이를 위해서는 잠수함 압력 선체의 구조 형상 설계가 초기에 수행되는 것이 합리적이다. 특히, 함미 원추부 구조물과 압력선체 평형부 및 함미 비압력선체를 연결하는 함미 트랜 지션 링의 경우, 설계된 잠수함에 따라 다양한 형상을 띄고 있다. 본 구조물 설계를 위해서는 응력 흐름과 연결성을 고려한 설계뿐만 아 니라 복잡한 형상이 기인한 구조물 제작 투입 시수 증가로 인한 원가 상승 또한 검토해야 한다. 따라서, 본 연구에서는 4가지 서로 다른 형상을 갖는 함미 트랜지션 링에 대해서 비선형 유한요소해석을 통한 구조 강도 검토와 더불어 함미 트랜지션 링 형상 복잡도에 따른 작 업 일수 및 자재비 검토를 통해 경제성 측면에서의 적정성 검토를 수행하였으며, 검토된 4가지 형상 중 가장 합리적인 잠수함 함미 트랜 지션 링 형상을 제안하였다.