The particle size of MgO was examined as a function of the Na content in Mg(OH)2 powders and the calcination temperature. Mg(OH)2 suspension was obtained by dropwise precipitation of Mg(NO3)2·6H2O and NaOH solutions. The suspension was diluted by varying the dilution volume ratio of distilled water to Mg(OH)2 suspension to change the Na salt concentration in the suspension. Mg(OH)2 slurry was filtered and dried at 60˚C under vacuum, and then its Mg(OH)2 powder was calcined to produce MgO with different amount of Na content at 500~900˚C under air. Investigation of the physical and chemical properties of the various MgO powders with dilution ratio and calcination temperature variation was done by X-ray diffraction, transmission electron microscopy, BET specific surface area and thermal gravimetric analysis. It was observed that MgO particle size could depend on the condition of calcination temperature and dilution ratio of the Mg(OH)2 suspension. The particle size of the MgO depends on the Na content remaining in the Mg(OH)2 powder, which powder was prepared by changing the dilution ratio of the Mg(OH)2 suspension. This change increased as the calcination temperature increased and decreased as the dilution ratio increased. The growth of MgO particle size according to the increase of temperature was more effective when there was a relatively high content of Na. The increase of Na content lowered the temperature at which decomposition of Mg(OH)2 to MgO took place, thereby promoting the crystal growth of MgO.

Silicon-based thin film was prepared at room temperature by an electrochemical deposition method and a feasibility study was conducted for its use as an anode material in a rechargeable lithium battery. The growth of the electrodeposits was mainly concentrated on the surface defects of the Cu substrate while that growth was trivial on the defect-free surface region. Intentional formation of random defects on the substrate by chemical etching led to uniform formation of deposits throughout the surface. The morphology of the electrodeposits reflected first the roughened surface of the substrate, but it became flattened as the deposition time increased, due primarily to the concentration of reduction current on the convex region of the deposits. The electrodeposits proved to be amorphous and to contain chlorine and carbon, together with silicon, indicating that the electrolyte is captured in the deposits during the fabrication process. The silicon in the deposits readily reacted with lithium, but thick deposits resulted in significant reaction overvoltage. The charge efficiency of oxidation (lithiation) to reduction (delithiation) was higher in the relatively thick deposit. This abnormal behavior needs to clarified in view of the thickness dependence of the internal residual stress and the relaxation tendency of the reaction-induced stress due to the porous structure of the deposits and the deposit components other than silicon.

Thin film electrode consisting purely of porous anodic tin oxide with well-defined nano-channeled structure was fabricated for the first time and its electrochemical properties were investigated for application to an anode in a rechargeable lithium battery. To prepare the thin film electrode, first, a bi-layer of porous anodic tin oxides with well-defined nano-channels and discrete nano-channels with lots of lateral micro-cracks was prepared by pulsed and continuous anodization processes, respectively. Subsequent to the Cu coating on the layer, well-defined nano-channeled tin oxide was mechanically separated from the specimen, leading to an electrode comprised of porous tin oxide and a Cu current collector. The porous tin oxide nearly maintained its initial nano-structured character in spite of there being a series of fabrication steps. The resulting tin oxide film electrode reacted reversibly with lithium as an anode in a rechargeable lithium battery. Moreover, the tin oxide showed far more enhanced cycling stability than that of powders obtained from anodic tin oxides, strongly indicating that this thin film electrode is mechanically more stable against cycling-induced internal stress. In spite of the enhanced cycling stability, however, the reduction in the initial irreversible capacity and additional improvement of cycling stability are still needed to allow for practical use.

Two-dimensional (2D) nano patterns including a two-dimensional Bravais lattice were fabricated by laser interference lithography using a two step exposure process. After the first exposure, the substrate itself was rotated by a certain angle, 90˚ for a square or rectangular lattice, 75˚ for an oblique lattice, and 60˚ for a hexagonal lattice, and the 90˚ and laser incident angle changed for rectangular and the 45˚ and laser incident angle changed for a centered rectangular; we then carried out a second exposure process to form 2D bravais lattices. The band structure of five different 2D nano patterns was simulated by a beam propagation program. The presence of the band-gap effect was shown in an oblique and hexagonal structure. The oblique latticed ZnO nano-photonic crystal array had a pseudo-bandgap at a frequency of 0.337-0.375, 0.575-0.596 and 0.858-0.870. The hexagonal latticed ZnO nano-crystallite array had a pseudo-bandgap at a frequency of 0.335-0.384 and 0.585-0.645. The ZnO nano structure with an oblique and hexagonal structure was grown through the patterned opening window area by a hydrothermal method. The morphology of 2D nano patterns and ZnO nano structures were investigated by atomic force microscopy and scanning electron microscopy. The diameter of the opening window was approximately 250 nm. The height and width of ZnO nano-photonic crystals were 380 nm and 250 nm, respectively.

In this study, nano-sized tin oxide powder with an average particle size of below 50 nm is prepared by the spray pyrolysis process. The influence of air pressure on the properties of the generated powder is examined. Along with the rise of air pressure from 0.1kg/cm2 to 3kg/cm2, the average size of the droplet-shaped particles decreases, while the particle size distribution becomes more regular. When the air pressure increases from 0.1kg/cm2 to 1kg/cm2, the average size of the dropletshaped particles, which is around 30-50 nm, shows hardly any change. When the air pressure increases up to 3kg/cm2, the average size of the droplet-shaped particles decreases to 30 nm. For the independent generated particles, when the air pressure is at 0.1kg/cm2, the average particle size is approximately 100 nm; when the air pressure increases up to 0.5kg/m2, the average particle size becomes more than 100 nm, and the surface structure becomes more compact; when the air pressure increases up to 1kg/cm2, the surface structure is almost the same as in the case of 0.5kg/cm2, and the average particle size is around 80- 100 nm; when the air pressure increases up to 3kg/cm2, the surface structure becomes incompact compared to the cases of other air pressures, and the average particle size is around 80-100 nm. Along with the rise of air pressure from 0.1kg/cm2 to 0.5kg/cm2, the XRD peak intensity slightly decreases, and the specific surface area increases. When the air pressure increases up to 1kg/cm2 and 3kg/cm2, the XRD peak intensity increases, while the specific surface area also increases.

The goal of this investigation was to produce a zirconia-family black ceramics that has enhanced functionality andreliability. Color zirconia ceramics have been produced by adding pigments. Pigments cause structural defects within zirconiaand result in a drop in physical properties. Using environmentally friendly rice husk, we produced a black zirconia that is freeof structural defects. In optimal firing conditions for black zirconia the calcining temperatures of the molding product arechanged from 400oC to 1200oC, and the firing temperatures are changed from 1400oC to 1600oC. Color of testing the specimenswas analyzed using Ultraviolet (UV) spectroscopy. Scanning Electron Microscope (SEM), EDAX (EDX), and Fourier transforminfrared spectroscopy (FT-IR) analyses were carried out in order to examine impregnation properties and crystal phases.Universial Test Machine (UTM) was used to measure the flexual strength as well as the compressive strength. Fromexperimental results, it was found that in optimal firing conditions the sample was calcined from 1000oC to 1500oC. Commissioninternationalde I’Edairage (CIE) values of manufactured black zirconia color were L*=29.73, a*=0.23, b*=−2.68. Thebending strength was 918 MPa and the compressive strength was 2676 MPa. These strength values are similar to typicalstrength values of zirconia, which confirms that carbon impregnation did not influence physical properties.

One of the trace constituents included in cement clinker, chromium, has become prominent and highly noticed lately as a social issue both inside and outside of this country because it affects the human body negatively. The purpose of the present study was to investigate leaching properties of water-soluble hexavalent chromium by different manufacturing conditions of cement clinker. Raw materials were prepared to add different SiO2, Al2O3 and Fe2O3 sources. After the raw materials, such as limestone, sand and clay, iron ore was pulverized and mixed, and the raw meal was burnt at 1450˚C in a furnace with an oxidizing atmosphere. Leaching of soluble hexavalent chromium showed a tendency to decrease with an increasing LSF and IM. However, leaching of soluble hexavalent chromium increased with an increasing S.M. Alkali contents of iron source minerals is closely related to the leaching properties of soluble hexavalent chromium. Green sludge has the highest content of alkali added; leaching of water-soluble hexavalent chromium was mostly high. In order to reduce the water-soluble hexavalent chromium in cement, reducing the alkali content in raw materials is important.

The a-Si:H/c-Si hetero-junction (HJ) solar cells have a variety of advantages in efficiency and fabrication processes. It has already demonstrated about 23% in R&D scale and more than 20% in commercial production. In order to further reduce the fabrication cost of HJ solar cells, fabrication processes should be simplified more than conventional methods which accompany separate processes of front and rear sides of the cells. In this study, we propose a simultaneous deposition of intrinsic thin a-Si:H layers on both sides of a wafer by dual hot wire CVD (HWVCD). In this system, wafers are located between tantalum wires, and a-Si:H layers are simultaneously deposited on both sides of the wafer. By using this scheme, we can reduce the process steps and time and improve the efficiency of HJ solar cells by removing surface contamination of the wafers. We achieved about 16% efficiency in HJ solar cells incorporating intrinsic a-Si:H buffers by dual HWCVD and p/n layers by PECVD.

An ultrafine grained complex aluminum alloy was fabricated by an accumulative roll-bonding (ARB) process using dissimilar aluminum alloys of AA1050 and AA5052 and subsequently annealed. A two-layer stack ARB process was performed up to six cycles without lubricant at an ambient temperature. In the ARB process, the dissimilar aluminum alloys, AA1050 and AA5052, with the same dimensions were stacked on each other after surface treatment, rolled to the thickness reduction of 50%, and then cut in half length by a shearing machine. The same procedure was repeated up to six cycles. A sound complex aluminum alloy sheet was fabricated by the ARB process, and then subsequently annealed for 0.5h at various temperatures ranging from 100 to 350˚C. The tensile strength decreased largely with an increasing annealing temperature, especially at temperatures of 150 to 250˚C. However, above 250˚C it hardly decreased even when the annealing temperature was increased. On the other hand, the total elongation increased greatly above 250˚C. The hardness exhibited inhomogeneous distribution in the thickness direction of the specimens annealed at relatively low temperatures, however it had a homogeneous distribution in specimens annealed at high temperatures.

본 연구는 유기액비 재료가 유기액비 제조시 화학적 특성 변화에 미치는 영향을 구명코자 충청북도농업기술원 플라스틱하우스에서 수행하였다. 계분, 대두박, 쌀겨 등 3처리를 하였다. 본 시험에서 얻어진 결과를 다음과 같이 요약할 수 있다. 액비 원료의 총 질소 함량은 대두박이 55 mg·kg−1으로 가장많았으며, 인산과 칼륨 함량은 계분에서 가장 많았다. 계분의pH는 중성에 가까웠으며, 대두박과 쌀겨는 강산성을 띠었다. 계분 액비의 EC는 발효기간이 증가할수록 증가하였고, 대두박과 쌀겨 액비는 발효기간 중 증가하다가 감소, 증가하는 경향이었다. 계분 액비의 황화수소 발생량은 발효 후 2주차에는3,200 mg·L−1이었으나, 발효 12주차에는 1,600 mg·L−1으로 감소하였고, 대두박과 쌀겨 액비는 발효 과정중 황화수소 가스가 발생하지 않았거나 거의 발생하지 않았다. 질소와 칼슘 함량은 계분 액비와 대두박 액비에서 가장 많았다. 인산, 마그네슘의 함량은 쌀겨 액비에서 각각 5.6 g·kg−1, 1.5 g·kg−1으로 가장 높았다. 칼륨은 처리에 따라 4.3-4.4g·kg-1으로 차이가 없었다.

Cereals are the main raw material for sunsik manufacture. As the fundamental processing step, it is very important to confirm the level of the microorganism contamination in the cereals. This study was carried out a micrbiological screening of cereal samples for sunsik from 19 companies located in South Korea. Ten kinds of cereals which were glutinous rice, barley, brownrice, blackbean, blackrice, blacksesame, sorghum, millet, perilla seed, and adlay were investigated. As the results, the contaminations of general bacterial were 3.1~8.6 log(CFU/g). The results of Escherichia coli were 1.0~3.4 log(CFU/g). There was no contamination of Salmonella. spp in any cereal samples except black sesame and mold was detected in barley. The experiment for microbiological contamination during sunsik processing was also investigated in this study. The results of general bacteria were detected as 5.1~8.5, 4.4~7.5,1.0~2.3, 2.4~4.2, 1.0~4.0, 3.4~4.2, 4.3~5.2, and 3.3~5.5 log(CFU/g) during environment of warehousing, washing,steaming, 1st cooling, drying, 2nd cooling, grinding, and packaging process, respectively. The results of coliform were 1.0~2.0 log(CFU/g) during warehousing respectively. Mold was found in warehousing. In case of the instruments, the contaminations of general bacterial were 4.2~7.5, 0.1~2.0, 0.1~3.2, 3.7~4.0, 2.5~3.0, and 3.8~5.2 log(CFU/g) in cereals tanks, washing machines, grinding machines, packaging machines, and workrooms. The results of coliform were 2.4~4.0, 0.0~4.1 log(CFU/g) in cereals tanks and grinding machines, respectively. Mold were only found in cereals tanks, grinding machines, and workings. Therefore, the risk of hazard microorganisms contmination might be decrased as the exhaustive management is applied to the whole sunsik process.

The removal amount of pesticide residue which were remained in baechu (Chinese cabbage) and perilla leaf were measured during the preparation process of kimchi. The amounts of diazinon, procymidone and endosulfan applied to chinese cabbage were 9.18 ± 0.03 mg/kg, 22.27 ± 0.22 mg/kg and 10.46 ± 0.02 mg/kg respectively. When chinese cabbage was brined with 10% salt solution for 12 hours, the removal rates of three pesticides were 22.5%, 25.3% and 0.6% for diazinon, procymidone and endosulfan, respectively. When chinese cabbage was brined and rinsed 3 times with water, the removal rates of three pesticides were 69.9%, 85.6% and 11.2% for diazinon,procymidone and endosulfan, respectively. When kimchi was prepared and fermented for 28 days at 4oC, the removal rates of three pesticides were 79.4%, 94.4% and 21.0% for diazinon, procymidone and endosulfan, respectively. The relative percentages of removal dose of pesticides during brining were 28.4%, 26.9% and 3.2% for diazinon, procymidone and endosulfan, respectively and which were 59.7%, 63.8% and 50.4% during rinsing and which were 11.9%,9.3% and 46.4% during fermentation, respectively. The amounts of diazinon, procymidone and endosulfan applied to perilla leaf were 18.11 ± 0.62 mg/kg, 31.80 ± 0.33 mg/kg and 12.01 ± 0.01 mg/kg, respectively. When perilla leaf was rinsed 3 times with water, the removal rates of three pesticides were 60.5%, 52.0% and 23.7% for diazinon, procymidone and endosulfan, respectively. When perilla leaf was rinsed and brined with 10% salt solution for 14 days, the removal rates of three pesticides were 93.9%, 92.4% and 49.6% for diazinon, procymidone and endosulfan, respectively. The relative percentages of removal dose of pesticides during rinsing were 64.5%, 56.3% and 47.8% for diazinon,procymidone and endosulfan, respectively, and which during brining were 35.5%, 43.7% and 52.2% for diazinon, procymidone and endosulfan, respectively.

To evaluate the indoor air quality of food manufacturing plants, the presence of viable bacteria and fungi was assessed in the indoor air of the facilities at which 9 food items were manufactured. Air samples were collected from the general zone, low clean zone and clean zone of each factory with an air sampler, in combination with plate counts agar using for bacteria, and dichloran-glycerol agar for fungi. The samples were incubated at 25℃for 4 to 7 days. After culture, the colony forming units (CFU) on each plate were counted and corrected with a positive hole conversion table. The average concentration of bacteria was 2.2 × 10³ CFU/㎥ in the general zone, 1.2 ×10³ CFU/㎥ in the low clean zone and 7.3 × 10² CFU/㎥ in the clean zone. The average concentration of fungal microbes was 2.5 × 10³ CFU/㎥ in the general zone, 2.6 × 10³ CFU/㎥ in the low clean zone, and 2.0 × 10² CFU/㎥in the clean zone. No meaningful differences were detected between the general zone and the low clean zone, but the clean zone had significantly lower concentrations than the other zones. Additionally, the identification of the fungi was performed according to morphological method using a giant culture and slide culture. The fungi were identified as belonging to 18 genera, and the genera Cladosporium(33%), Penicillium(29%) and Aspergillus(26%), predominated. Aspergillus isolates were identified to species level, and A. ochraceus, a mycotoxigenic species, was identified. As part of the effort to control the quality of the indoor air of food manufacturing plants, our results show that continued studies are clearly warranted.

This study was conducted to investigate the physicochemical characteristics of Eungi, which is used as a breakfast or health food. We manufactured lotus root starch and Eungi by a traditional method and discovered that the viscosity of Eungi with 4-5% starch content was similar to fermented milk. When the physicochemical properties and sensory acceptability of a Eungi beverage combined with different amounts (0.5, 1.0, 1.5, and 2.0%) of lotus root starch were investigated, consumer acceptability was highest with Eungi combined with 0.5% starch and 6% sugar. When the physicochemical properties and sensory acceptability of Eungi beverage combined with different extract bases were investigated, the acceptability of taste and texture was highest with purple sweet potato extract and the acceptability of color was highest with omija extracts.

This study was conducted to develop a novel salad dressing composite recipe of natural seasoning containing the dried sea tangle(Laminaria japonica) that has a high preference. Sea tangle(Laminaria japonica) is included in the vitamins and minerals, magnesium, calcium, iodine, iron content, such as high, and contained in Sea tangle alginate is not a small conference known as dietary fiber. To manufacture salad dressing with sea tangle, dressing with 0%, 3%, 6%, 9%, and 12% added sea tangle were prepared and tested for quality. The pH tended to increase with the increased sea tangle in addition but in contrast, acidity showed. The ``L`` color decreased with added sea tangle, whereas the ``a`` and ``b`` values increased. Brix measurements increase with added sea tangle. The strength texture results, 0% was the highest, lowest 9%. Bitterness and chewiness texture results, 9% was the highest, lowest 0%. According to the sensory test results, in the topic overall quality 3% was by 3.76 point the highest. But, during total nine clause, in clause six, by 6% was the highest.

본 연구에서는 용액 캐스팅법을 이용하여 각기 다른 함량의 VMT가 첨가된 SPAES/VMT 복합막이 제조되었다. SPAES 매트릭스 내의 VMT입자 분산은 전자주사현미경으로 관찰된 평균분포에 의해 확인되었다. 1 wt%보다 적은 함량을 포함한 복합막은 고분자 매트릭스 내에 좋은 분산성을 나타내어 막의 상부층과 하부층에 매끈한 표면을 가졌다. 복합막의 함수율은 온도가 증가함에 따라 급격하게 증가되었으며 VMT는 높은 이온교환능력으로 인하여 강한 수분친화도를 가짐으로 인해 높은 모든 흡착된 수분은 bound water인 것으로 확인하였다. VMT의 함량이 1 wt%보다 적게 첨가된 복합막에서 증가된 이온전도도와 낮아진 메탄올 투과도를 확인할 수 있었다. 모든 복합막 중에서 SPAES/VMT 1.0 wt% 복합막은 선택도 측면에서 가장 뛰어난 연료전지 성능을 가졌으며 Nafion 112과 비교하여 두배 이상 우수한 값을 나타내었다. 이것은 SPAES/VMT 1.0 wt% 복합막이 직접메탄올 연료전지의 구동을 위한 가장 우수한 조건이 될것이라 사료된다.

We are crystallized to the linear low density polyethylene(LLDPE) particles by a thermally induced phase separation(TIPS). TIPS process based on the phase separation mechanism was performed for the LLDPE system which undergoes liquid-solid phase separation. The linear low density polyethylene particle formation occurred by the nucleation and growth mechanism in the metastable region. Although the growth rates depended on the experimental conditions such as the polymer concentration and temperature, the particles were larger when the polymer concentration was higher or temperature was higher. The particles were observed by SEM. The LLDPE particle size distribution became broader when the polymer concentration was higher.

One of main catalysts for De-NOx in SCR is a V2O5/TiO2, and this work formulated powdery catalysts focusing ultimately on corrugate catalytic support. The prepared catalyst consisted of anatase TiO2. Amount of the added vanadium oxide determined the viscosity of catalyst slurry, which is important for washcoat for a final corrugate type catalytic reactor. The test showed a proportional relation between adsorption amount of ammonia and specific surface area. De-NOx efficiency could be obtained up to 96.3 % at 400℃ with a spacial velocity of 4,000hr-1.

매립지나 유기성폐기물의 혐기성소화에서 발생되는 바이오 메탄가스 혼합물에서 이산화탄소를 제거하고 고농도의 메탄을 연료로 정제하는 기술은 온실가스의 저감과 신재생에너지 개발의 두 가지 장점을 함께 가지고 있다. 고분자 소재를 이용한 분리막기술은 메탄의 분리에 경제적으로 적용될 수 있는 기술이다. 본 연구에서는 이산화탄소/메탄의 선택도가 50, 이산화탄소의 투과도가 3.4 barrer로 알려진 폴리이서설폰[1]을 고분자 소재로 사용하고, 비용매 첨가제로 폴리이서설폰을 잘 팽윤시키는 아세톤의 함량을 달리하여 비대칭 중공사막을 제조하였다. 아세톤의 함량 9 wt%, 방사높이 10 cm, 4 wt% PDMS 코팅을 거친 폴리이서설폰 중공사막은 이산화탄소 투과도 36 GPU 및 이산화탄소/메탄 선택도 46의 우수한 성능을 나타내었다. 최적조건의 비대칭 폴리이서설폰 중공사막을 이용하여 제조된 모듈의 이산화탄소/메탄 순수가스 및 혼합가스 투과특성을 압력, 유입조성의 변화에 따라 관찰하여 분리막 공정을 구성한 결과 10 atm의 압력조건에서 95%의 메탄을 58%의 회수율로 얻을 수 있는 것으로 나타났다.