This study is to investigate the degree of field awareness of how each provision of the Serious Disaster Punishment Act will affect accident prevention. As a result of conducting a survey of construction site workers, it was analyzed that construction site workers had a low sense of safety and did not voluntarily engage in safety activities. And it can be seen that they are taking a very passive position that it is efficient to implement safety under the supervision of the supervisor. Workers who need voluntary construction site safety activities are most aware of the situation at the site, but the problem was pointed out as “lack of procedures for listening to opinions and preparing improvement measures” for these problems. Future research is needed to see if this is a problem for individual workers or for those in charge of safety and health who do not correct it even though active opinions have been submitted.

This study investigated the stone Angbu-ilgu (scaphe sundial) of the Korea Meteorological Administration (KMA) and the Seoul Museum of History (SMH). Since the first Angbu-ilgu was produced in Korea in 1434 (the year of the reign of King Sejong), Angbu-ilgu has been reproduced with various materials. The upper surface of these two stone Angbu-ilgus symbolizes the horizon. On the hemisphere concave at the center of the horizon, the South Pole, the time line, and the season line are engraved. On the horizon of both the KMA and SMH Angbu-ilgus, the schematic, typeface, and composition of the inscription completely coincide with each other. In this study, it was estimated that the appearance of the KMA Angbu-ilgu, which was damaged at some point previously at least once, was similar to that of the SMH Angbu-ilgu, and this means that it is superficially similar with Treasure No 840, the stone horizontal sundial. In the concave hemisphere of both the stone Angbu-ilgus of the KMA and SMH, there are hour lines and 24 solar-term lines (13 line), and there is an intersection point where these lines meet the horizon, respectively. It can be verified that these intersections of these two Angbu-ilgus can be calculated as having a latitude of +37°39′15″. The hour lines of the two stone Angbu-ilgus show that they were made after about 1900.

The occurrence of Laodelphax striatellus (SBPH) in Korea ranged 0.3-19.3 individuals in 2021, and 0.3-23.3 individuals in 2022 during the investigation period. Nilaparvata lugens (BPH) was not observed in 2021, but N. lugens (BPH) showed the highest number(82.0 inds.) in late September of 2022. The occurrence of Sogatella furcifera (WBPH) was not severe during the study period. Compared to Korea’s situation, N. lugens (BPH) and S. furcifera (WBPH) in Asian regions showed high occurrence in Bangladesh and Sri Lanka. The results of the field survey could be confirmed with the occurrence pattern of about once or twice in their regions. Continuous monitoring is required for the best control of planthopper species in rice production regions of Asia. We anticipate that exchange of occurrence information and establishment of a control cooperation system will improve rice productivity in Asian regions by preventing outbreak of planthopper species and reducing damages caused by the species.

교량 인프라는 국민의 경제와 사회적 활동에 반드시 필요한 물리적 기반시설이고, 국민의 안전과 편의성에 직결되는 시설이므로 국민의 입장에서 편익을 고려해야 한다. 교량의 구성요소 중 바닥판은 교량 전체의 생애주기 동안 필연적으로 교체 시기가 도래하고 파손 등으로 인한 부분 교체도 빈번하게 이루어지고 있다. 바닥판 교체공사 시 거더와 바닥판을 합성하는 기 존 용접 전단연결재의 문제점을 해결하기 위한 볼트 접합 전단연결재(DY볼트)는 바닥판 철거 공정에서 파쇄를 최소화하고 교 체공사를 위한 전단연결재 재시공이 용이하여 공사 기간을 기존 대비 단축할 수 있는 것으로 분석되었다. 공사기간 중 도로차 단으로 인해 발생하는 도로이용자비용을 산출하여 기존 공법과 비교하는 방법으로 볼트 접합 전단연결재를 적용한 강합성 교량 의 경제성을 도로이용자(국민) 입장에서 분석하였다.

The effect of Cr and Mo contents on the hydrogen embrittlement of tempered martensitic steels was investigated in this study. After the steels with different Cr and Mo contents were austenitized at 820 °C for 90 min, they were tempered at 630 °C for 120 min. The steels were composed of fully tempered martensite with a lath-type microstructure, but the characteristics of the carbides were dependent on the Cr and Mo contents. As the Cr and Mo contents increased, the volume fraction of film-like cementite and prior austenite grain size decreased. After hydrogen was introduced into tensile specimens by electrochemical charging, a slow strain-rate test (SSRT) was conducted to investigate hydrogen embrittlement behavior. The SSRT results revealed that the steel with lower Cr or lower Mo content showed relatively poor hydrogen embrittlement resistance. The hydrogen embrittlement resistance of the tempered martensitic steels increased with increasing Mo content, because the reduction in the film-like cementite and prior austenite grain size plays an important role in improving hydrogen embrittlement resistance. The results indicate that controlling the Cr and Mo contents is essential to achieving a tempered martensitic steel with a combination of high strength and excellent hydrogen embrittlement resistance.

밀은 세계 3대 주요 작물이지만 우리나라는 대부분 수입에 의존하고 있으며, 자급률이 1%도 도달하지 못한 실정이다. 국내 밀 품종은 40여 종 이상으로 지속적으로 개발되고 있으며, 품종마다 용도와 농업적 특성이 달라 목표 형질에 맞는 적절한 품종을 선택하여 재배하는 것이 중요하다. 품종을 정확하고 빠르게 판별하기 위해선 분자 마커 기술이 필요하다. 분자 마커는 생육 환경과 시기에 영향을 받지 않고 다양한 품종을 신속하고 정확하게 구분할 수 있어 유전적 변이성, 농업 형질 등을 분석하기에 유용하다. 본 연구는 기존에 보고된 국내 밀 32품종에 대한 SCAR (Sequence Characterized Amplified Region) 판별 마커를 재검정하여 재현성이 높은 마커를 선별하였으며, 기존에 검정되지 않은 국내 밀 9품종에 추가 적용하여 비교분석하였다. 15개의 마커 세트 중 6개의 마커가 재현성과 정확도가 높은 것으로 확인되었고, 최종적으로 국내 41품종 중 4, 7, 8, 10, 11, 12번 마커를 이용하여 다홍, 금강, 밀성, 조은, 수강, 한백, 조광, 영광을 판별할 수 있었다. 또한, 4번 마커를 통한 증폭산물의 염기서열 분석을 통해 SNP (Single Nucleotide Polymorphism)를 발굴하여 ‘올밀’에 대한 새로운 품종 판별 마커인 SdHRM1과 SdHRM2를 개발하여 HRM (High Resolution Melts) 분석을 시행하여 육안으로 판단하기 어려운 SNP를 정확하게 판별할 수 있었다. 품종간의 SNP를 활용한 품종 마커 기술은 다양한 농업형질에 적용할 수 있으며, 분자 육종 프로그램에 실질적인 도움이 되는데 큰 기여를 할 것으로 사료된다.

PURPOSES : Roller-compacted concrete pavement (RCCP) is a superstiff-consistency concrete pavement that exhibits excellent strength development owing to a hydration reaction and interlocking aggregates owing to the roller compaction. A zero-slump concrete mixture is generally used. Hence, it is important to control the consistency of the RCCP mixture to prevent the deterioration of the construction quality (such as material separation during paving). The workability of the RCCP is characterized by its consistency and controlled by the Vebe time, whereas a conventional concrete pavement is controlled based on the slump test. The consistency of the RCCP changes over time after concrete mixing owing to delivery, construction time delays, etc. Thus, it is necessary to use the optimum Vebe time to achieve the best construction quality. Therefore, this study aims to develop a Vebe time prediction model for efficiently controlling the consistency of RCCPs according to random time variations. METHODS : A Vebe time prediction model was developed using a multiple linear regression analysis. A dataset of 131 samples was used to develop the model. The collected data consisted of variables with large potential effects on the consistency of the RCCP, such as the water-cement ratio (W/C), sand/aggregate ratio (S/a), water content (ω), water content per unit volume (W), cement (C), fine aggregate (S), coarse aggregate (G), water reducing admixtrue (PNS), air-entraining admixture (AE), delay time (T), air temperature (TEM), and humidity (HUM). In the multiple linear regression analysis, the mentioned parameters were used as the independent variables, and the Vebe time was the dependent variable. The Vebe time prediction models were evaluated by considering the adjusted R2 and p-values. The selection of the model was based on the largest R2 value and an acceptable p-value (p<0.05). RESULTS : The Vebe time prediction model achieved an adjusted R2 value of 64.14% with a significance level (p-value) of less than 0.05. This shows that the predictive model is adequately described for the dependent variable, and that the model is suitable for Vebe time predictions. Moreover, the significance level of the independent variables is less than 0.05, indicating significant effects on the Vebe time (i.e., the dependent variable). CONCLUSIONS : The Vebe time prediction model developed in this study can be used to estimate Vebe times with an R2 of 63.33% between the measured and predicted values. The proposed Vebe time prediction model is expected to be effectively utilized for the quality control of RCCP mixtures. Moreover, it is expected to contribute to achieving good RCCP construction quality.

A heat exchanger refers to a pressure vessel that indirectly exchanges heat between low-temperature/ high-temperature fluids with a solid wall interposed therebetween, and a shell-and-tube cylindrical heat exchanger is generally applied. The shell-and-tube cylindrical heat exchanger is widely used in ships and there is a problem in that the welding area is narrow and welding defects occur a lot due to high-level welding. In particular, in the case of a ship heat exchanger, if a problem occurs in the welding part during operation, the possibility of a safety accident is high, and repair is not easy. In this study, to solve this problem, the GTAW(Gas Tungsten Arc Welding) method was applied to secure the optimum conditions for pipe welding of STS304 material with a thickness of 5.5mm and to conduct a test. Afterwards, in accordance with the ASME rules, welding performance was verified through cross-sectional observation of welds, mechanical property tests, (tensile strength, bending strength, cryogenic impact strength) and non-destructive testing(PT, RT).

9% nickel steel has remarkable mechanical properties in a cryogenic condition and is widely used in storage containers for LNG fueled ships. Demand for laser welding rather than conventional arc welding has grown to increase manufacturing efficiency. However there are various types of heat sources which are suggested by other researchers. With that, it is difficult to select a proper heat source shape for welding conditions. The author proposed a representative heat source model that can cover most of suggested heat source models through previous studies. Welding power was fixed at 4kW and the speed was changed to 1.0m/min, 1.5m/min, and 2.0m/min respectively. The shapes of the welding heat sources were derived, and the tendency of the main parameters was also deducted. It was observed that the width and depth of the weld bead decreased as the welding speed increased through welding experiment, parameters of welding heat source are changed linearly. Based on this study, it is expected that it will be possible to estimate the shape of the heat source under untested welding conditions.

본 논문에서는 1차원 오일러 보 요소(Euler-Bernoulli Beam Element)를 이용한 회전익기 축계에 대한 중량 최적설계를 수행하였다. 회전 축계의 특성을 고려해 비틀림(Torsion)과 베어링과 같은 축지지 강성 및 플랜지(Flange) 질량을 모두 고려하였고, 동적 안전성 확 보를 위해 고유치 해석을 수행하여 임계속도(Critical Speed)와 기어박스로부터 오는 치 변형 가진을 회피할 수 있도록 하였다. 축의 길 이는 고정된 상태에서 두께와 반경을 조절하여 중량 최적화를 수행하였으며, 최적화 과정은 2단계로 나누어 진행하였다. 1단계에서 는 비틀림 강도를 제약조건으로 하여 중량을 최적화한 후 2단계에서는 축계 안정성 확보 기준(Headquarters, U.S. Army Material Command, 1974)에 따라 축의 비틀림 강도에 대한 제약조건을 만족시키며, 축의 1차 모드가 임계속도를 회피할 수 있도록 축 1차모드 와 임계속도의 차이가 최대가 되도록 최적화를 진행하였다. 주어진 1차원 보 요소를 이용하여 최적설계를 한 결과를 3차원 유한요소 모델과 실제 제작된 축게의 시험결과와 비교하여 제안된 방법을 검증하였다.

시공 중인 건물은 시공이 완료된 건물과는 다르게 콘크리트의 강도발현이 충분히 이루어지지 않았기 때문에 지진과 같은 자연재해 에 더 취약한 모습을 가질 수 있다. 현재 국내 기준은 건축물의 내진등급별 최소성능 목표를 제시하고 있지만, 설계를 위한 지진하중은 재현주기 2,400년의 지진위험도를 기반으로 한다. 하지만 건물의 시공기간은 건물의 사용기간보다 훨씬 짧기 때문에 재현주기 2,400 년의 지진을 시공 중인 건물에 적용하는 것은 과도하다. 따라서 이 연구는 주거용으로 사용되는 철근콘크리트 건물의 시공 중 지진하 중을 분석하기 위해 5층, 15층, 25층, 60층 건물의 시공단계모델을 작성하고 재현주기에 따라 저감한 지진하중을 적용하여 구조적 안 정성을 확인하였다. 그 결과, 시공기간에 따라 선정한 재현주기의 지진을 적용할 때 구조적 안정성을 확인하였으며, 건물의 규모의 따 라 구조적 안전성을 확보할 수 있는 지진재현주기를 확인하였다.

PURPOSES : A methodology for estimating micro-emission factors using vehicle trajectory data collected from navigation and DTG devices and basic emission factors for each vehicle type of the MOtor Vehicle Emission Simulator (MOVES) is presented. The methodology can calculate micro-emissions based on only the traffic volume and average speed for each vehicle type. METHODS : Cluster analysis was performed by accumulating the trajectories of individual vehicles on a specific road section into speed groups in which vehicles drove with the same range of average speed. Then, the micro-emission factors were estimated for each speed group. RESULTS : Using the vehicle trajectory data revealed that the emissions calculated from micro-emission factors estimated by the proposed methodology were similar to the sum of the emissions calculated from the vehicle trajectories for each vehicle. CONCLUSIONS : The micro-emission factor database for each road type and vehicle type proposed in this study should be useful for estimating vehicle emissions on the road. The proposed method can calculate emissions in the same way as the macroscopic analysis method, using the traffic volume, average speed, and link length.

오늘날 디지털 경제로의 전환 속에서 데이터는 사업자의 경쟁력을 결정하는 핵심적인 투입요소 로 평가되고 있다. 데이터 기반 사업모델은 구글, 애플, 페이스북, 아마존 등 거대 온라인 플랫폼의 성공을 배경으로 디지털 경제에서 큰 비중을 차 지하고 있다. ‘데이터 경제’ 혹은 ‘데이터 주도 경 제’라는 표현은 이러한 디지털 경제의 특징을 잘 나타낸다. 그러나데이터 활용의긍정적인 측면의 이면에서는 데이터를 이용한 진입장벽의 구축과 같은 부정적인 효과도 함께 논의되고 있다. 과거 에는 플랫폼 사업자가 이용자의 데이터를 대량으 로 수집하여 상업적으로 활용하는 것이 경쟁법의 문제가 아닌 개인정보 보호법의 문제로 다루어졌 으나, 근래에는 데이터 집중에 관한 논의가 개인 정보 보호 정책상 의제에 그치지 않고 각국 경쟁 당국의 관심을 끌고 있다. 대표적으로 독일 연방 카르텔청은 2019. 2. 6. 페이스북이 이용자의 개 인정보를 포함한 데이터를 방대하게 수집하여 맞 춤형 광고에 이용한 행위가 시장지배적 지위 남 용행위에 해당한다고 결정하였고, 독일 연방최고 법원도 2020. 6. 23. 페이스북의 데이터 수집⋅ 이용행위가 착취 남용에 해당한다고 판단하였다. 우리나라 공정거래위원회도 데이터 주도 경제의 특수성을 법집행에 반영하기 위하여 심사기준을 제⋅개정하는 등 노력해왔고, 2020. 12. 28. 배 달의 민족과 요기요 간 기업결합 사건에서는 데 이터 집중으로 인한 경쟁제한 우려를 해소하기 위해 요기요 지분의 매각을 명하면서 매각이 완 료될 때까지 요기요의 데이터를 공유하지 못하도 록 조치하기도 하였다. 이처럼 디지털 경제가 가 속화되면서 과거에는 경쟁법 적용 대상으로 여겨 지지 않았던 데이터 집중 내지 독점 현상이 경쟁 법적 관점에서 문제가 되고 있는바, 시장의 변화 를 예의주시하고 해외 경쟁당국들의 데이터 독점 에 대한 반독점 규제 동향을 참고하여 데이터 관 련 경쟁제한 우려에 대응해 나갈 필요가 있다.

Environmental regulations of the International Maritime Organization (IMO) are getting stricter, and the demand for replacing the fuel of ships with eco-friendly fuels instead of heavy oil in the shipbuilding and marine industries is increasing. Among eco-friendly fuels, LNG (liquefied natural gas) is currently the most popular fuel. This is because it is an alternative that can avoid the IMO's environmental regulations by replacing fuel. In PART 1, as a basic study of laser welding of high manganese steel materials, a fiber laser bead-on-plate experiment was conducted using nitrogen protective gas, and the effect of each factor on the penetration shape was analyzed through cross-sectional observation. In PART II, argon and helium shielding gases, not the nitrogen shielding gas used in PART I, were tested under the same experimental conditions and the effect of the shielding gas on penetration during laser welding was conducted.

본 연구는 전화코칭을 병행한 운동프로그램이 지역사회 거주 독거노인의 균형능력, 악력 및 우 울에 미치는 효과를 조사하기 위한 단일집단 사전사후 원시실험연구이다. 연구대상자는 경기도 S시에 위치 한 노인복지관에 등록된 독거노인 20명이 참여하였으며, 자료수집기간은 2021년 7월 03일부터 2021년 10 월 14일까지 총 12회기 프로그램을 시행하였다. 프로그램 전후에 대상자 가정에 직접 방문하여 4단계 균형 검사, 근력검사, 악력 및 우울을 측정하였다. 중재 프로그램은 탄력밴드와 악력볼을 이용하여 구성하였으며 매주 전화코칭 중재를 제공하였다. 연구결과, 전화코칭을 병행한 운동 프로그램은 대상자의 4단계 균형기 능(3단계)(t=-2.37, p=.029), 4단계 균형기능(4단계)(t=-2.46, p=.024), 우측 악력(t=-2.18, p=.042), 우울 (t=2.82, p<.001)에서 통계적으로 유의한 차이가 나타났다. 본 연구 결과를 바탕으로 전화코칭을 병행한 운 동프로그램은 독거노인의 균형능력, 악력 향상 및 우울 감소를 위한 간호중재로 활용될 수 있을 것으로 기 대된다.

Environmental regulations of the IMO (International Maritime Organization) are becoming more and more conservative. In order to respond to IMO, the demand for replacing the fuel of ships with eco-friendly fuels instead of conventional heavy oil is increasing in the shipbuilding and offshore industries. Among eco-friendly fuels, LNG (Liquefied Natural Gas) is currently the most popular fuel. LNG is characteristically liquefied at -163 degrees, and at this time, its volume is reduced to 1/600, so it is transported in a cryogenic liquefied state for transport efficiency. A tank for storing this should have sufficient mechanical/thermal performance at cryogenic temperatures, and among them, high manganese steel is known as a material with high price competitiveness and satisfying these performance. However, high manganese steel has a limitation in that the mechanical performance of the filler metal is lower than that of the base metal called ‘under matching’. In this study, to overcome this limitation, a basic study was conducted to apply the fiber laser welding method without filler metal to high manganese steel. To obtain efficient welding conditions, in this study, bead-on-plate welding was performed by changing the fiber laser welding speed and output using helium shielding gas, and the effect of each factor on the penetration shape was analyzed through cross-sectional observation.