Thermal property represents a critical metric when evaluating the performance of next generation nuclear graphite. Despite the extensive measurement data available, a detailed investigation into the influence of microstructure on graphite’s thermal conductivity remains underexplored. In this work, taking advantage of the distinct microstructures between different graphite grades, a comparative study of four graphite grades was conducted to elucidate the structure–property relationship. The microstructures of graphite were characterized by Raman spectroscopy and X-ray diffraction techniques, demonstrating specimen preparation induced damage and annealing induced restoration. Thermal properties were investigated across multiple scales using laser flash analysis and photothermal radiometry. The results indicate that despite similar densities, thermal conductivity varies significantly between different grades and correlates positively with crystallite sizes. By interpolating an infinitely large crystallite and removing the impact of macroscale porosity, an upper bound for the thermal conductivity of isotropic defect-free nuclear graphite has been established.

국제 유학생의 창업에 대한 세계적 관심이 높아지고 있음에도 불구하고, 개인의 심리적 자원이 실제 창업 행동으로 어떻게 전환되는지는 아직 충분히 탐구되지 않았다. 본 연구는 한국 내 국제 유학생을 대상으로, 심리자본이 창업 의도와 행동에 미치는 영향을 분석하고, 이 과정에서 문화적응역량의 매개 역할에 초점을 두었다. 심리자본 이론과 계획된 행동이론(Theory of Planned Behavior)을 기반으로, 180명의 유학생 데이터를 부분 최소자승 구조방정식모형(PLS-SEM)을 통해 분석하였다. 분석 결과, 희망(β = .204, p = .010), 자기효능감(β = .307, p = .006), 낙관주의(β = .323, p < .001)는 문화적응역량을 유의하게 향상시키는 반면, 회복탄력성은 유의하지 않았다(β = .016, p = .844). 문화적응역량은 창업 의도 에 긍정적인 영향을 미치지만(β = .567, p < .001) 행동에는 직접적인 영향을 주지 않았으며, 창업 의도는 행동을 강하게 예측하였다(β = .465, p < .001). 또한 문화적응역량이 창업 행동에 미치는 간접효과는 창업 의도를 통해 유의하게 나타나(β = .264, p < .001), 완전매개 효과가 검증되었다. 본 연구는 심리학과 문화 적 관점을 통합함으로써 창업 이론을 확장하고, 대학과 정책입안자들이 유학생의 심리자원, 문화적응능 력, 제도적 지원을 강화하여 창업 참여를 촉진해야 함을 강조한다.

The aromatization degree of coal liquefaction pitch is closely related to its molecular structure evolution and the properties of derived carbon fibers. Using refined coal direct liquefaction pitch (RCLP) as raw material, pitches with different aromatization degrees were prepared by the self-pressurization/N₂ blowing two-stage thermal condensation method. Carbon fibers were then produced through melt spinning, oxidative stabilization, and carbonization. As the aromatization degree advanced, the C/H atomic ratio rose from 1.55 to 2.01, with the mesophase content nearing 100%. During RCLP thermal polymerization, large toluene-insoluble molecules were readily generated, yet the enrichment of the mesophase was comparatively sluggish. The spinnable pitch from RCLP had a relatively high aliphatic hydrogen content (33.40% ~ 13.69%) and a lower aromaticity (91.62% ~ 96.90%). Increasing aromatization made the carbon fiber cross-section’s radial transverse texture more distinct and ordered. The carbon layers stacked closely and parallelly, leading to a continuously rising tensile modulus. Due to the inhomogeneity from isotropic and anisotropic component changes, the carbon fiber tensile strength first decreased and then increased. When the spinnable pitch C/H ratio was 1.84, the mesophase pitch-based carbon fiber had an average diameter of 14.78 μm, a tensile strength of 1140 MPa, and a tensile modulus of 209 GPa.

Phase change materials (PCM) with enhanced thermal conductivity and electromagnetic interference (EMI) shielding properties are vital for applications in electronic devices, energy storage, and aerospace. However, achieving a synergistic improvement in both thermal and EMI shielding performance remains a significant challenge. This study presents the development of phase change composites reinforced with 3D Ag foam and short carbon fibers (SCF) to address this challenge. Ag@SCF/ PCM composites were fabricated using a vacuum-assisted impregnation and curing process. Polyethylene glycol and epoxy resin formed the PCM matrix, while SCF and Ag foam created a dual-scale interpenetrating network to provide channels for phonon and electron transmission. The dual-scale network significantly improves thermal conductivity (2.24 W/m·K) and EMI shielding (69.7 dB), while maintaining latent heat storage (melting: 71.5 J/g, freezing: 68.7 J/g). These multifunctional properties make Ag@SCF/PCM composites promising candidates for applications requiring simultaneous thermal management and electromagnetic performance optimization.

To improve the proton conductivity of the proton exchange membranes (PEM), an amino derivative with sulfonic acid groups was used to modify graphene oxide (GO), resulting in sulfonated graphene oxide (S-GO), which was then incorporated into a perfluorinated sulfonic acid (PFSA) matrix to fabricate a PFSA/S-GO composite membranes. Elevating the doping concentration of S-GO within the composite membrane has resulted in enhanced proton conductivity, outperforming the baseline PFSA membrane across a range of temperatures. Notably, this conductivity ascended to 291.89 mS/cm when measured at 80 °C under conditions of 100% RH. Furthermore, the strong interface interaction between sulfonated graphene oxide and perfluorinated sulfonic acid polymer endowed the composite proton exchange membrane with excellent thermal stability and mechanical strength.

The synthesis of functional carbon materials with controllable morphology and structure using a simple, effective, and green process starting from biomass has been an attractive and challenging topic in recent years. After decades of technological development, high value-added biomass-derived carbon nanomaterials with different morphologies and structures prepared by low-temperature hydrothermal carbonization (HTC) have been gradually developed into a huge system covering different series in different dimensions, and are widely used in the fields of adsorption, electrochemical energy storage, and catalysis. However, due to a vague understanding of the fundamental structure–performance correlation and the absence of customized material design strategies, the diverse needs in practical applications cannot be well met. Herein, we reviewed the mechanism, modifications, and applications of the low-temperature HTC method for biomass. The synthesis mechanisms, structural designs strategies, and related applications of biomass-derived hydrochar are highlighted and summarized in different dimensions, including six major categories: zero-dimensional spherical structure, one-dimensional fibrous and tubular structure, two-dimensional lamellar structure, three-dimensional hierarchical porous structure, and special-shaped asymmetric structure. Then a sustainability assessment is conducted on the hydrothermal carbonization process. Finally, the controllable preparation of biomass-derived hydrochar is summarized and prospected for the application requirements in different fields.

Biomass-derived carbon materials have attracted considerable attention in electromagnetic wave (EMW) absorption applications due to their advantages of low cost, light weight, and sustainability. Herein, bagasse-based porous carbon (BPC) was prepared by canonization and activation process from natural waste bagasse. The porous flower-like MoS2/ BPC composites were successfully prepared for efficient microwave absorption via hydrothermal process by in-situ formation of flower-like MoS2 into the porous structure of BPC. The effect of hydrothermal time and hydrothermal temperature on surface morphology, degree of graphitization, surface chemical composition and impedance matching of the prepared samples was investigated. Results demonstrated that when the hydrothermal temperature was 220 °C, and the hydrothermal time was 24 h, the obtained MoS2/ BPC sample (named as MoS2/ BPC-220 ℃) showed the minimum reflection loss value (RL) of − 41.6 dB at 8.96 GHz and exhibited effective microwave absorption bandwidth (EAB) of 4.32 GHz at a relatively thin thickness of 1.5 mm. This work provides a promising way to prepare novel biomass-derived porous carbon for strong broadband electromagnetic absorption.

A substantial quantity of discarded tires has inflicted harm on the environment. Microwave pyrolysis of discarded tires emerges as an efficient and environmentally friendly method for their recycling. This research innovatively utilizes the characteristics of microwave rapid and selective heating to pyrolyze waste tires into porous graphene under the catalysis of KOH etching. Moreover, this study comprehensively investigates the dielectric characteristics and heating behavior of waste tires and different proportions of waste tire–KOH mixtures. It validates the preparation of graphene through KOH-catalyzed microwave pyrolysis of waste tires, tracking morphological and structural changes under varying temperature conditions. The results indicate that optimal dielectric performance of the material is achieved at an apparent density of 0.68 g/cm3 at room temperature. As the temperature increases, the dielectric constant gradually rises, particularly reaching a notable increase around 700 °C, and then stabilizes around 750 °C. Additionally, the study investigates the penetration depth and reflection loss of mixtures with different proportions, revealing the waste tire–KOH mass ratio of 1:2 demonstrates favorable dielectric properties. This research highlights the impressive microwave responsiveness of the waste tire–KOH mixture, Upon the addition of KOH, the mixed material exhibits an augmented dielectric constant and relative dielectric constant, supporting the viability of KOH-catalyzed microwave pyrolysis for producing porous graphene from waste tires. This method is expected to provide a new method for the valuable reuse of waste tires and a technology for large-scale, efficient and environmentally friendly production of graphene.

Exploring highly efficient, and low-cost oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) catalysts is extremely vital for the commercial application of advanced energy storage and conversion devices. Herein, a series of graphene-like C2N supported TMx@C2N, (TM = Fe, Co, Ni, and Cu, x = 1, 2) single- and dual-atom catalysts are designed. Their catalytic performance is systematically evaluated by means of spin-polarized density functional theory (DFT) computations coupled with hydrogen electrode model. Regulating metal atom and pairs can widely tune the catalytic performance. The most promising ORR/OER bifunctional activity can be realized on Cu2@ C2N with lowest overpotential of 0.46 and 0.38 V for ORR and OER, respectively. Ni2@ C2N and Ni@C2N can also exhibit good bifunctional activity through effectively balancing the adsorption strength of intermediates. The correlation of reaction overpotential with adsorption free energy is well established to track the activity and reveal the activity origin, indicating that catalytic activity is intrinsically governed by the adsorption strength of reaction intermediates. The key to achieve high catalytic activity is to effectively balance the adsorption of multiple reactive intermediates by means of the synergetic effect of suitably screened bimetal atoms. Our results also demonstrate that lattice strain can effectively regulate the adsorption free energies of reaction intermediates, regarding it as an efficient strategy to tune ORR/OER activity. This study could provide a significant guidance for the discovery and design of highly active noble-metal-free carbon-based ORR/OER catalysts.

In the “宀” radical of Shuowen Jiezi (說文解字): “家，凥也。从宀，豭省聲。𠖔，古文 家.” Duan Yucai believed that, the character “家” (jia) is composed of the radicals “宀” and “豕”, and should be classified under the radical “豕” instead of “宀”. The so-called “豭省聲” mentioned by Xu Shen is baseless. Based on the research of scholars in the Qing Dynasty, as well as the evidence from oracle bone inscriptions and bronze inscriptions, it can be concluded that “豭” is a newly created character, and its ancient form should be “𢑓”, which is “豕” with an additional semantic stroke indicating a male pig. The original intention of “豭省聲” should be to omit the character form of “叚” while preserve the pronunciation of “叚”. This takes into account both the ideographic character “家” derived from “ (𢑓)” and the phonetic-semantic character “家” derived from “ (豭)”. Duan Yucai proposed the concepts of “the original meaning of character creation” and “the original sense of character usage” to distinguish between the original meaning and the extended borrowed meaning, which is the value of his theory.

This paper presents the construction and characterization of an amperometric immunosensor based on the graphene/gold nanoparticles (AuNPs/GO) nanocomposite for the detection of the bladder cancer biomarker, apolipoprotein A1 (Apo-A1). The morphological analysis of the AuNPs/GO nanocomposite demonstrated an almost spherical shape of AuNPs and the successful coverage of their surface by graphene oxide. An increased G peak and decreased D peak after the association of AuNPs with GO, implied a reduction in graphene defects. The X-ray photoelectron spectroscopy (XPS) indicated a significant decrease in the quantity of oxygen-containing functional groups in the AuNPs/GO nanocomposite, as compared to the original GO. Furthermore, the developed sensor demonstrated commendable sensitivity and selectivity, with a wide linear range for Apo-A1 detection. Importantly, the immunosensor exhibited remarkable stability over a period of 14 days, signifying its potential for practical applications.

Aurantii Fructus Immature (AFI) and Aurantii Fructus (AF) are two important traditional Chinese herbs. As the harvesting time varies, the medicinal value of the plants is not uniform. Consequently, it has been difficult to quickly recognize them within the realm of traditional Chinese medicine. Separation and detection technologies are employed in combination to create fingerprints for identification. We proposed the utilization of graphene-assisted electrochemical fingerprint technology to acquire fingerprints of two varieties of medicinal materials. Simultaneously, we also obtained their fingerprints through HPLC. Two fingerprint recognition technologies were compared for their effectiveness. The findings demonstrate that the signals obtained through electrochemical fingerprinting have a higher recognition rate.

Decabromodiphenyl ether (BDE209) is a persistent aromatic compound widely associated with environmental pollutants. Given its persistence and possible bioaccumulation, exploring a feasible technique to eradicate BDE209 efficiently is critical for today’s environmentally sustainable societies. Herein, an advanced nanocomposite is elaborately constructed, in which a large number of titanium dioxide ( TiO2) nanoparticles are anchored uniformly on two-dimensional graphene oxide (GO) nanosheets ( TiO2/GO) via a modified Hummer’s method and subsequent solvothermal treatment to achieve efficient photocatalytic degradation BDE209. The obtained TiO2/ GO photocatalyst has excellent photocatalytic due to the intense coupling between conductive GO nanosheets and TiO2 nanoparticles. Under the optimal photocatalytic degradation test conditions, the degradation efficiency of BDE209 is more than 90%. In addition, this study also provides an efficient route for designing highly active catalytic materials.

With the popularity of live streaming commerce, the characteristics of streamers and products subtly influence consumer behavior through visual live streaming form. Based on dual-process theory, this paper develops a comprehensive theoretical model to examine how consumer perceived streamer characteristics and product characteristics influence streamer attractiveness and product attractiveness, and explore how consumer behavior inertia is affected by streamer attractiveness and product attractiveness. An online survey consisting of 300 participants was recruited to empirically examine the proposed research model. The results indicated that consumer perceived streamer characteristics and product characteristics are important factors affecting the streamer attractiveness and product attractiveness, which in turn positively affect consumer’s shopping experience memory, which further influence consumer behavior inertia. In addition, the moderating effects of mindfulness are also examined.

An all-perovskite oxide heterostructure composed of SrSnO3/Nb-doped SrTiO3 was fabricated using the pulsed laser deposition method. In-plane and out-of-plane structural characterization of the fabricated films were analyzed by x-ray diffraction with θ-2θ scans and φ scans. X-ray photoelectron spectroscopy measurement was performed to check the film’s composition. The electrical transport characteristic of the heterostructure was determined by applying a pulsed dc bias across the interface. Unusual transport properties of the interface between the SrSnO3 and Nb-doped SrTiO3 were investigated at temperatures from 100 to 300 K. A diodelike rectifying behavior was observed in the temperature-dependent current-voltage (IV) measurements. The forward current showed the typical IV characteristics of p-n junctions or Schottky diodes, and were perfectly fitted using the thermionic emission model. Two regions with different transport mechanism were detected, and the boundary curve was expressed by ln I = -1.28V - 13. Under reverse bias, however, the temperature- dependent IV curves revealed an unusual increase in the reverse-bias current with decreasing temperature, indicating tunneling effects at the interface. The Poole-Frenkel emission was used to explain this electrical transport mechanism under the reverse voltages.