본 연구에서는 소형선박용 중·고속 디젤엔진에 적용하여 연구 중인 SCR+DPF 기술을 저속엔진이 설치된 선박에 탑재하여 해상 실증 시험을 수행하였다. 대상 선박(총 톤수 2,881 톤, 정격출력 1,470kW@240rpm ×1)은 국내 연해를 운항하는 일반화물선으로 배출저감설 비의 선박 탑재를 위해 도면 개발, 승인 및 선박 임시검사를 수행하였다. 저감성능 확인을 위해서 가스상물질 측정장비는 NOx technical code 및 ISO-8178의 분석방법을 준용하는 장비를 사용하였으며, 입자상물질 측정장비는 국제해사기구(IMO)에서 논의하고 있는 블랙카본 측정 방법 중 하나인 스모크미터를 사용하였다. 시험은 황 함유량 따라 MGO(0.043%), LSFO(0.42%) 2종의 연료를 사용하였으며 실제 운항 하는 엔진회전수(130, 160 및 180 rpm)를 고려하여 시험 조건을 설정하였다. 시험 조건에 따라 배출저감설비의 전·후단에서 가스상 및 입 자상(매연) 물질을 측정하여 배출저감설비의 저감효율을 확인하였으며 모든 시험 조건에서 NOx의 경우 90% 이상, 입자상물질(매연)의 경우 95% 이상의 저감효율을 확인하였고 엔진 성능의 영향을 줄 수 있는 배기가스 압력은 허용배압 기준인 50mbar 이하를 만족하였다. 본 연구를 통해 해상실증 연구의 중요성과 중소형 저속엔진 선박의 질소산화물 및 입자상물질의 동시 저감을 위한 대응 기술로 SCR+DPF 설비 적용 가능성을 확인할 수 있었다.
전산유체역학을 사용하는 일반적인 선박의 저항성능 평가는 많은 시간과 비용이 필요하며, 이를 줄이기 위한 다양한 방법이 연구되고 있다. 선박의 주요 치수나 단면을 이용하는 기존의 방법들은 선형에 크게 좌우되는 저항성능을 추정하는데 한계가 있다. 본 논 문에서는 선형 격자의 기하학적 정보를 입력으로 선체 표면의 저항성능을 빠르게 추정할 수 있는 심층신경망 모델을 제안한다. Perceiver IO 기반의 제안하는 심층신경망 모델은 시간 단계별로 계산이 필요한 전산유체역학 기법과 달리 바로 저항성능 추정이 가능하며, 저속비 대선의 일종인 50K 탱커 선박을 대상으로 한 데이터집합에서 평균 1% 미만의 오차로 저항성능을 추정하는 결과를 보인다.
In the event of an defective wire in the low-speed CAN communication of vehicle, the problem had to be solved by relying on fault codes or using expensive measuring equipment. An experiment was conducted to analyze waveforms of communication circuits with wire conditions such as normal, short circuits in the main body, and mutual short circuits. When the controller drives the CAN transceiver and transmits a message, the voltage and current waveforms were measured using an OEM oscilloscope to check for abnormalities in the circuit. As a result, it was confirmed that when a defective wire occurs in low-speed CAN communication, the CAN driver can switch to the fail-safe mode to exchange normal messages.
In the past, the U.S. NRC(Nuclear Regulatory Commission) strictly required testing of the EDG for NPP through Reg.Guide 1.108 Rev 1. However, these test requirements acted as a deterioration and wear factor for diesel engines, and are now applying Reg.Guide 1.9 Rev 3, which relaxed regulatory requirements and improved performance monitoring. After applying the new regulatory guidelines in this study, the EDG analyzed the performance of the combustion chamber. As a result, there were no signs of deterioration or decreased performance of the current EDG. This is due to slow start, short operation time, the use of high quality fuel oil and proper maintenance. On the other hand, if the performance is proven, it is judged that proper period extension of cylinder maintenance is possible.
In this study, we investigated the effects of diesel-palm oil biodiesel-ethanol blends on combustion and emission characteristics in a 4-cylinder common rail direct injection (CRDI) diesel engine at low idling operations. The engine speed and engine load was 750 rpm and 40 Nm, while the main and pilot injection timing was respectively fixed at 2 °CA before top dead center (BTDC) and 20 °CA BTDC. The experimental results showed that the cylinder pressure increased with the increasing of palm oil biodiesel ratio from 20% to 100%. In addition, the peak value of cylinder pressure increased by 4.35% compared with pure diesel fuel when 5 vol.% ethanol oil added to diesel oil. Because the palm oil biodiesel and ethanol are the oxygenated fuel, the oxygen content played an important role in improving combustion. Based on the high oxygen content of biodiesel and ethanol, their mixing with diesel fuel effectively reduced PM emissions but increased NOx slightly, while CO and HC had no significant changes.
According to the automobile industry has been developing day by day, traffic accidents are increasing and the rear-end collision is the second largest of the entire collision. Due to the high social cost caused by rear-end collision, several studies are in progress at home and abroad. Previous studies have shown that neck injury caused by rear-end collisions can be prevented by seat conditions. In this study, to find the condition that reduces neck injury, change of neck injury in rear-end collision is analyzed according to headrest height, seatback angle, and seatback torque using BioRID II dummy model and passenger behavior analysis program MADYMO. Therefore, it is expected that the condition of each variable to reduce the risk of injury to the neck can be applied to the seat design, which will reduce the injury and the social cost caused by the rear-end collision.
In the area around Jeju Island, the squid jigging fishery and the hair-tail angling are popular. Therefore, the study on the characteristics of the formation and shift of fishing grounds is very important. We have received and analyzed AIS data of all vessels around Jeju Island from October 16, 2016 to October 16, 2017, and extracted the positions of the fishing vessels with the same operational characteristics as the fishing vessels of their fisheries. The distribution chart of the frequency of fishing vessels appearing in each predefined fishing grid (1 NM × 1 NM) was analyzed. So we took a analogy with the monthly shift of fishing grounds. Many fishing vessels appeared in the seas around Jeju Island from November 2016 to January 2017, and the frequency of their appearance was maintained. In November, however, fishing vessels were mostly concentrated in coastal waters. Yet, the density gradually weakened as they moved into January. From February, the frequency itself began to decline, making it the worst in April. The high concentration of fishing vessels in the waters leading from Jeju Island's northwest coast to south coast in November is believed to be related to the yellowtail fishery that are formed annually in the coastal waters off the island of Marado. In May 2017, the appearance frequency of fishing vessels increased and began to show a concentration in coastal waters around Jeju Island. Fishing vessels began to flock in waters northwest of Jeju Island beginning in July and peaked in August, and by September, fishing vessels were moving south along the coast of Jeju Island, weakening the density and spreading out. Between July and August, fishing vessels were concentrated in waters surrounding Jeju Island, which is believed to be related to the operations of fishing vessels for the squid jigging fishery and the hair-tail angling.
Vegetables and fruits contain a great deal of vitamins, minerals, dietary fiber and phytochemicals. Therefore, healthconcious consumer prefer beverage made from fresh fruits and vegetables due to their health benefits. This study was conducted to investigate differences in nutritional composition and sensory characteristics of juices depending on the apparatus used: either a low-speed juicer or high-speed blender. All ingredients could be made into juice without addition of water using the low speed juicer. However, addition of water was necessary to produce juice with the high-speed blender. Phenol and flavonoid content, were higher in juice made with the low-speed juicer than that produced with the high-speed blender and were correlated with DPPH radical scavenging ability. Protease activity of pineapples juices was not significantly different for the two methods, but protease activity of kiwi juice was about 8 times higher in juice made with low-speed juicer than that made with the high-speed blender. SOD activity also tended to be higher in the juice made with low-speed juicer. The concentration of dissolved oxygen in the juice made with high-speed blender was higher than that of juice made with a low-speed juicer and was correlated with color change. In addition, the high-speed blender caused an increase juice temperature, but temperature was not changed during use of the low-speed juicer. The noise level of the low-speed juicer was low, but the high-speed blender had high noise intensity comparable to that of railway or aircraft noise. In the sensory evaluation of juice, juice made with the low-speed juicer was preferred over juice made with the high-speed blender. As a result, the overall quality of the juice produced using the low-speed juicer was superior.
본 연구에서는 연안의 해저면에 누적된 퇴적오염물을 효율적으로 수거할 수 있는 저속 쌍동형 정화선에 대한 선수선형의 개념설계에 대해 수행하였다. 선형설계는 선체건조가 용이하도록 단순화하였으며, 쌍동선 선형의 선수 Water line, 선수각 등의 변화에 따른 저항성능의 영향을 검토하였다. Ansys CFX를 이용한 수치시뮬레이션과 회류수조에서의 모형시험결과와의 비교/분석 등을 통하여 선수부 선형변화에 따른 저항성능과 자유표면 유동특성 사이의 관계를 고찰하였으며, 그 결과 선수재 위치와 어깨부 체적의 선수부 이동에 따른 파형개선으로 조파저항이 감소하는 등 저항성능의 향상을 확인하였다.
In this study, the lower power consumption FET-DC contactor for golf cart and low speed electric vehicle has been designed and developed. Also, the author carrying out many measurements and tests such as an electric power consumption, current consumption, calorific value, size, volume and weight of the DC contactor for the various cases. As a result, the author found that a prototype of the lower power consumption FET-DC contactor can not only reduce calorific value, size, volume and weight but also improve an electric power and current consumption.
The automotive bumper has the functions of strength, rigidity and fine sight. It protects the driver, front and rear sides of car body through shock absorption at the traffic accident of car. This study investigates the impacts on front side and corner with the low speed of 4.5 km/h by using the model of SUV car body. The models are modelled by CATIA program with three dimensions and are analyzed by the finite element program of ANSYS Explicit STR. The maximum equivalent stresses at impacts of front side(case 1) and corner (case 2) at bumper are 261.72MPa and 365.02MPa respectively. As this stress at case 2 becomes 40% higher than at case 1, the impact of corner is happened easier than at the damage at the impact of front side. These stresses at case 1 and case 2 are shown above the yield stress at material property of steel, it is thought that there are the possibilities of plastic damages at two cases. The maximum deformation and equivalent stress at the support 2 of case 2 become 5 times and 3 times higher than at the support 1 respectively. The damage possibility due to impact at low speed is investigated by the basic analysis result of this study. And this result can be utilized at inspecting the result of impact test on bumper hereafter.
IIWPG protocol for the dynamic testing of motor vehicle seats is a test procedure for ratings of seats and head restraints for neck injury prevention in low speed rear impacts. In this study, we evaluates the performance of the car seat in the dynamic test was enacted by IIWPG and initial geometry test that has been enacted by RCAR to vehicle being sold in the market today. 6 models became the A and G in the final rating that reflects the results of the dynamic test and Initial geometry test. Electronic active head restraint was found to be allowed to operate quickly headrest, it is very effective in the prevention of neck injury in support of the head of the passenger. we suspects that this is contributed lower the value injuries reduce the relative acceleration between the chest and head. It is determined that the expanded application is required up to the small car because rating appears high in the vehicle equipped with the electric active head restraint. In addition to the evaluation of the impact velocity and collision direction, neck injury continued research to present proposals for improvement is required future.
The Notched Ring Test(NRT) has proven to be very useful in determining the slow crack growth behavior of polyethylene pressure pipes. In particular, the test is simple and an order of magnitude shorter in experimental times as compared to the currently used Notched Pipe Test(NPT), which makes this method attractive for use as the accelerated slow crack growth test. In addition, since the NRT specimen is taken directly from the pipe, having maintained the cross-section, processing induced artifacts that would affect the slow crack growth behavior are not altered. This makes the direct comparison to the slow crack growth specimen in pipe from more meaningful. In this study, for comparison with other available slow crack growth methods, including the NPT, the stress intensity factor equation for NRT specimen was developed and demonstrated of its accuracy within 3% of that obtained from the finite element analysis. The equation was derived using a flexure formula of curved beam bending along with numerically determined geometric factors. The accuracy of the equation was successfully tested on 63, 110, 140, 160, 250, and 400 mm nominal pipe diameters, with crack depth ranging from 15 % to 45 % of the pipe wall thickness, and for standard dimensional ratio(SDR) of 9, 11, and 13.6. Using this equation the slow crack results from 110SDR11 NRT specimen were compared to that from the NPT specimen, which demonstrated that the NRT specimen was equivalent to the NPT specimen in creating the slow crack, however in much shorter experimental times.
Recently imported vehicles are increasing rapidly and related vehicle accidents have also increased. In addition, the number of accident in 2010 was approximately 205,000 cases, about 6,000 billion to repair the vehicle accident was paid. RCAR low-speed crash tests to calculate the imported car insurance repairs, domestic cars and imported car repairs were compared. Average repair cost 2,920,000 won in domestic cars and imported cars are 14,570,000 won, imported cars were approximately five times higher than domestic cars. The results of comparing the total repair cost, imported vehicle repairs to the front of the T-car was the highest, rear repairs to the C-car was the highest. New car value for repairs, parts price, damage in terms of imported cars were higher than that of the domestic cars. In order to avoid the social costs of spending, calculated based on proper repairs on imported vehicles, improvement of excessively high parts prices and the repairman cost are needed.
자기부상열차가 중 저속 및 초고속 주행 시 차량의 주행특성 및 교량의 동적 응답 결과를 제시하고자 한다. 수직 자유도 및 회전 자유도를 포함한 10자유도 자기부상열차에 대한 운동방정식을 유도하고, 모드 중첩법을 이용하여 교량의 운동방정식을 구성하였다. 또한 제어 방법으로 UTM01제어기법을 적용하여 수치해석을 수행하였다. 해석 예제로 노면조도, 가이드웨이의 처짐비, 차량 속도 등이 교량의 처짐과 차량의 부상공극 및 여러 가지 변수에 미치는 영향을 파악하였다. 부상공극은 조도의 조건에 따라 그 차이가 확연히 드러나고 또한 자기부상열차의 속도가 증가함에 따라 부상공극이 증가함을 알 수 있었다. 그리고 자기부상열차가 중, 저속 주행 시에는 교량에 대한 영향이 미비하지만 초고속 주행 시 교량에 대한 동적확대계수가 큰 값을 보여주었다.
The neck injury occupies the most of injury that happened by the rear impact car accident. This study was analyzed about influence of the neck injury in low speed rear impact and car crash accident investigation. There is no neck injury in low speed side rear impact. On the other hand, there is initial neck injury symptom of 10 % but no long-term neck injury symptom in low speed offset rear impact. It appeared that the possibility of neck injury in low speed rear impact is low. For the more study about the neck injury, it should be evaluate the effects of the car body structure, frame structure and rear crash pattern.
복합적층판은 다른 금속재료에 비해 높은 비강도, 비강성 등의 우수한 역학적 특성을 지니므로, 최근 다양한 분야에서 사용하고 있다. 그러나 이러한 복합적층판은 충격에 약하다는 단점이 있다. 그리하여 복합적층판의 충격거동에 대한 많은 연구가 이루어지고 있다. 충격거동을 조사하기 위해서는 우선 충격체와 복합적층판사이의 접촉력을 계산하여야 한다. 접촉력을 알기 위해서는 운동방정식, 복합적층판의 운동방정식 그리고 압입량에 관한 관계식을 동시에 풀어야 한다. 본 연구에서는 고전적인 헤르츠식, 썬식, 썬&양식 그리고 썬&탄식을 포함한 유한요소프로그램을 이용하여 복합적층판의 저속충격거동을 조사한다.