Low- and intermediate level waste (LILW) repository in Gyeongju, Korea is in operation and the radioactive waste should satisfy the waste acceptance criteria (WAC) of the repository. Among the WAC of the Gyeongju LILW repository, the leachability index criterion is considered to be the criterion that is directly related to the isolation of the radionuclides from biosphere. Cesium, strontium, and cobalt should satisfy the leachability index larger than six by following the ANS 16.1 leaching test method. Several research were performed for the leachability index of Cs, Sr, and Co by following the ANS 16.1 leaching test method. However, the test condition of the previous research is expected to be different to the condition of the actual waste. Due to the radioactivity of the radionuclide such as Cs, Sr and Co, most of the research applied the surrogate of those radionuclides. The concentration of those nuclides was generally measured by the inductively coupled plasma (ICP) equipment, however, high concentration compared to the disposal limit of those nuclides due to the detection limit of the ICP was applied. From the Freundlich and Langmuir adsorption isotherms, the adsorption of the nuclides differs according to the concentration of the nuclides. As the leachability index of the nuclides is affected by the adsorption of the nuclides on the binding material, the effect of nuclide concentration is expected to be not ignorable. Therefore, the leachability index difference according to the nuclide concentration should be compared to avoid over- or underestimation of the leachability index. In this study, the difference in the leachability index according to the concentration of nuclides is aimed to be checked. Cs, Sr, and Co, which should satisfy the leachability index criterion in the WAC of the Gyeongju repository, were selected as target nuclides. Three concentrations were selected to compare the leachability index: 0.1 mol, 0.001 mol and below the regulatory exemption concentration. The concentration of non-radioactive nuclides in the leachant was measured by ICPOES and ICP-MS while the concentration of radionuclides was measured by HPGe. The result of this study can be applied as background data enhancing the WAC or disposal concentration limit of the radionuclides in Gyeongju LILW repository.

The oxygen evolution reaction (OER) is very sluggish compared to the hydrogen evolution reaction (HER). Considering this difference is essential when designing and developing a cost-effective and facile synthesis method for a catalyst that can effectively perform OER activity. The material should possess a high surface area and more active sites. Considering these points, in this work we successfully synthesized sheets of cobalt phosphate hydrate (CP) and sulphurated cobalt phosphate hydrate (CPS) material, using simple successive ionic layered adsorption and reaction (SILAR) methods followed by sulfurization. The CP and CPS electrodes exhibited overpotentials of 279 mV with a Tafel slope of 212 mV dec1 and 381 mV with a Tafel slope of 212 mV dec1, respectively. The superior performance after sulfurization is attributed to the intrinsic activity of the deposited well-aligned nanosheet structures, which provided a substantial number of electrochemically active surface sites, speeded electron transfer, and at the same time improved the diffusion of the electrolyte.

In this study, the effects of Co content on the microstructure and Charpy impact properties of Fe-Cr-W ferritic/martensitic oxide dispersion strengthened (F/M ODS) steels are investigated. F/M ODS steels with 0–5 wt% Co are fabricated by mechanical alloying, followed by hot isostatic pressing, hot-rolling, and normalizing/tempering heat treatment. All the steels commonly exhibit two-phase microstructures consisting of ferrite and tempered martensite. The volume fraction of ferrite increases with the increase in the Co content, since the Co element considerably lowers the hardenability of the F/M ODS steel. Despite the lowest volume fraction of tempered martensite, the F/M ODS steel with 5 wt% Co shows the highest micro-Vickers hardness, owing to the solid solution-hardening effect of the alloyed Co. The high hardness of the steel improves the resistance to fracture initiation, thereby resulting in the enhanced fracture initiation energy in a Charpy impact test at – 40oC. Furthermore, the addition of Co suppresses the formation of coarse oxide inclusions in the F/M ODS steel, while simultaneously providing a high resistance to fracture propagation. Owing to these combined effects of Co, the Charpy impact energy of the F/M ODS steel increases gradually with the increase in the Co content.

In order to identify changes in the nature of the particles due to changes in the inflow rate of the raw material solution, the present study was intended to prepare nano-sized cobalt oxide (Co3O4) powder with an average particle size of 50 nm or less by spray pyrolysis reaction using raw cobalt chloride solution. As the inflow rate of the raw material solution increased, droplets formed by the pyrolysis reaction showed more divided form and the particle size distribution was more uneven. As the inflow rate of the solution increased from 2 to 10 ml/min, the average particle size of the formed particles increased from about 25 nm to 40 nm, while the average particle size did not show significant changes when the inflow rate increased from 10 to 50 ml/min. XRD analysis showed that the intensity of the XRD peaks increased remarkably when the inflow rate of the solution increased from 2 to 10 ml/min. On the other hand, the peak intensity stayed almost constant when the inflow rate increased from 10 to 50 ml/min. With the increase in the inflow rate from 2 to 10 ml/min, the specific surface area of the particles decreased by approximately 20 %. On the contrary, the specific surface area stayed constant when the inflow rate increased from 10 to 50 ml/min.

Using the spray pyrolysis process, nano-sized cobalt oxide powder with average particle size below 50 nm was prepared from cobalt chloride solution. The influences of the raw material solution on the properties of the powder formed examined. When the concentration of Co was low(20 g/L), the average particle size of the powder formed was roughly 20 nm, and the cohesion between these particles was significantly strong. When the concentration of Co increased to 100 g/L, the droplets nearly failed to exist in circular form and reflected a severely divided form. Furthermore, the average size of the particles formed was roughly 40 nm, and the particles reflected a polygonal form. When the solution was increased to nearly saturation level (Co at 200 g/L), the particle size distribution reflected significant unevenness due to severe droplet division while the surface also reflected significant unevenness. Furthermore, the average size of the particles formed increased significantly to 70 nm. The results of XRD analysis showed that the strength of the peaks reflected very little change when the concentration of Co was increased from 20 g/L to 50 g/L. Alternatively, when the concentration was increased to 100 g/L, the strength of the peaks increased compared to when the concentration was 50 g/L. However, when the concentration was increased to 200 g/L, the strength of the peaks failed to reflect significant change compared to when the concentration was 100 g/L. The specific surface area dramatically decreased by 30 % when the concentration of Co was increased from 20 g/L to 50 g/L. Alternatively, when the concentration of Co the solution increased to 100 g/L, the specific surface area decreased by roughly 15 %. Furthermore, when the concentration of Co was increased to nearly saturation level(200 g/L), the specific surface area decreased by roughly 35%.

코발트는 자연적으로 암석, 토양 물 등에서 발견되는 요소일 뿐만 아니라 산업화에 의해 생성되는 유해물질 중의 하나이다. 환경에서는 코발트 (II)와 코발트 (III)의 두 가지 산화물로 존재하며, 연안 해역으로 유입 시 먹이연쇄를 통해 해양생태계 전반에 영향을 미칠 수 있다. 따라서 본 연구는 유용 수산생물로써 조간대 암반 지역에 서식하는 말똥성게(Hemicentrotus pulcherrimus)를 이용하여 cobalt (Co (II); 10,

Diamond segments were fabricated by cold pressing and sintering under pressure at the temperature up to . Based on the results of this investigation, it can be concluded that the segments containing 39wt.% cobalt in the matrix material have the highest bending strength at a fracture probability of 50 % due to the weibull distribution method. According to the weibull statistics, it was also determined that the transverse rupture strength was the best for 39 wt.% cobalt ratio in the matrix material for the fracture probability when the other variables are the same.

Effect of phase transformation and grain-size variation of hot-pressed cobalt on its dry sliding wear was investigated. The sliding wear test was carried out against glass (83% SiO2) beads at 100N load using a pin-on-disk wear tester. Worn surfaces, cross sections, and wear debris were examined by an SEM. Phases of the specimen and wear debris were identified by an XRD. Thermal transformation of the cobalt from the hcp ε phase to the γ (fcc) phase during the wear was detected, which was deduced as the wear mechanism of the sintered cobalt.

In the present study, the focus is on the effect of cobalt oxide powder in the carbothermal reduction of the titanium-cobalt-oxygen based oxide powder by solid carbon for the optimizing synthesis process of ultra fine TiC/Co composite powder. The titanium-cobalt-oxygen based oxide powder was prepared by the combination of the spray drying and desalting processes using the titanium dioxide powder and cobalt nitrate as the raw materials. The titanium-cobalt-oxygen based oxide powder was mixed with carbon black, and then this mixture was carbothermally reduced under flowing argon atmosphere. Changes in the phase structure and thermal gravity of the mixture during carbothermal reduction were analysed using XRD and TGA. Titanium-cobalt-oxygen based oxide powder desalted at had a mixture of . And the one desalted at had a mixture of . In the case of the former powder, the reduction of cobalt oxide powder in the titanium-cobalt-oxygen based oxide powder occurred at lower temperature than the latter one. However, the carbothermal reduction of titanium dioxide powder in the titanium-cobalt-oxygen based oxide powder with a mixture of occurred at higher temperature than the one with a mixture of . And also, the former powder showed a lower TiC formation ability than the latter one.

본 연구에서는 라테라이트광의 건식 분쇄가 니켈 및 코발트의 침출에 미치는 영향을 조사하였다. 시료로 사용한 라테라이트광은 주로 SiO2, Fe2O3, MgO로 이루어져 있으며, 니켈과 코발트의 함량은 0.81% Ni, 0.02% Co이었다. 주 구성 광물은 리자다이트와 석영이며, 미량의 포스터라이트와 엔스터타이트를 함유하고 있었다. 분쇄가 진행됨에 따라 시료의 평균입도, 비표면적, 밀도는 감소하는 경향을 보였으며, X-선 회절분석을 통해 리자다이트의 비정질화가 진행됨을 확인하였다. 분쇄에 의한 석영의 물성변화는 나타나지 않았으나, 리자다이트의 Mg-OH 결합이 파괴됨으로써 니켈 및 코발트의 침출율이 향상됨을 알 수 있었다. 분쇄가 진행됨에 따라 니켈과 코발트의 침출율은 증가하였으며, 60분 분쇄한 시료의 경우, 사용한 무기산의 종류에 관계없이 니켈과 코발트의 침출율은 약 80%로 나타났다.