본 실험에서는 α-Al2O3 지지체에 무전해도금을 이용하여 Pd-Ag-Cu 분리막을 제조하였다. Pd, Ag, Cu는 각각 무 전해도금을 통해 지지체 표면에 코팅하였고, 합금의 형성을 위해 무전해도금 중간에 H2, 500°C의 조건에서 18 h 동안 열처리 를 진행하였다. 이를 통해 제조된 Pd-Ag-Cu 분리막은 SEM을 통해 표면을 관찰하였으며, Pd 분리막의 두께는 7.82 μm, Pd-Ag-Cu 분리막의 두께는 3.54 μm로 측정되었다. EDS와 XRD 분석을 통해 Pd-Ag-Cu 합금이 Pd-78%, Ag-8.81%, Cu-13.19%의 조성으로 형성된 것을 확인하였다. 기체투과 실험은 H2 단일가스와 H2/N2 혼합가스에서 실험을 진행하였다. H2 단일가스에서 측정한 수소 분리막의 최대 H2 flux는 Pd 분리막의 경우 450°C, 4 bar에서 74.16 ml/cm2·min이고, Pd-Ag-Cu 분리막의 경우 450°C, 4 bar에서 113.64 ml/cm2·min인 것을 확인하였고, H2/N2 혼합가스에서 측정한 separation factor의 경우 450°C, 4 bar에서 각각 2437, 11032의 separation factor가 측정되었다.

The International Atomic Energy Agency recommends the deep geological disposal system as one of the disposal methods for high-level radioactive waste (HLW), such as spent nuclear fuel. The deep geological disposal system disposes of HLW in a deep and stable geological formation to isolate the HLW from the human biosphere and restrict the inflow of radionuclides into the ecosystem. It mainly consists of an engineered barrier and a natural barrier. Safety evaluation using a numerical model has been performed primarily to evaluate the buffer’s long-term stability. However, although the gas generation rate input for long-term stability evaluation is the critical factor that has the most significant influence on the long-term hydraulic-mechanical behavior of the buffer, in-depth research and experimental data are lacking. In this study, the gas generation rate on the interface between the disposal canister and the buffer material, a component of the engineered barrier, was mainly studied. Gas can be generated between the disposal canister and the buffer material due to various causes such as anaerobic corrosion of the disposal canister metal, organic matter decomposition, radiation decomposition, and steam generation due to high temperature. The generation of gas in such a disposal environment increases the pore gas pressure in the buffer and causes internal cracks. The occurred cracks increase the intrinsic permeability of the buffer, which leads to a decrease in the primary performance of the buffer. For this reason, it is essential to apply the appropriate gas generation rate according to the disposal condition and buffer material for accurate long-term stability analysis. Therefore, the theoretical models regarding the estimation of gas generation were summarized through a literature study. The amount of gas generated was estimated according to the disposal environment and material of the disposal canister. It is expected that estimated values might be used to estimate the long-term stability analysis of buffer performance according to the disposal condition.

본 연구에서는 비용매 유도 상분리법을 이용하여 폴리에테르이미드 계열의 중공사형 분리막을 제조하였다. 제조 된 중공사막의 모폴로지 조절을 위해 첨가제로는 THF, Ethanol, LiNO3를 사용하였다. 또한 높은 수소분리막의 개발을 위해 모폴로지와 기체투과성능을 특성평가를 통해 방사조건을 최적화하였다. 그 결과 THF의 함량이 증가할수록 수소/이산화탄소 선택도가 증가하였다. 하지만 trade-off 관계로 인하여 투과율은 감소하였다. Ethanol을 첨가하였을 때는 finger-like 구조를 나타냈고, LINO3를 첨가하였을 때 Sponge 구조를 보였다. 특히, PDMS 코팅층을 최적화한 중공사막의 경우, 투과율은 40 GPU, 수소/이산화탄소 선택도는 5.6을 나타냈다.

We investigate the reduction of SnO2 and the generation of syngas(H2, CO) using methane(CH4) and hydrogen(H2) or a mixed gas of methane and hydrogen as a reducing gas. When methane is used as a reducing gas, carbon is formed by the decomposition of methane on the reduced Sn surface, and the amount of generated carbon increases as the amount and time of the supply of methane increases. However, when hydrogen is used as a reducing gas, carbon is not generated. High purity Sn of 99.8 % and a high recovery rate of Sn of 93 % are obtained under all conditions. The effects of reducing gas species and the gas mixing ratio on the purity and recovery of Sn are not significantly different, but hydrogen is somewhat more effective in increasing the purity and recovery rate of Sn than methane. When 1 mole of methane and 1 mole of hydrogen are mixed, a product gas with an H2/CO value of 2, which is known to be most useful as syngas, is obtained.

수소를 연료로 사용하는 PEMFC는 고효율⋅출력밀도를 나타내며, 짧은 시동시간, 우수한 응답특성에 따라 현지설치형 발전기술로 사용되며, 이를 위한 고효율 연료처리장치가 필수적이다. SMR반응은 연료당 고회수율을 때문에 경제성이 우수하며, 전환율 확보를 위해 700°C, 20 bar 이상의 운전조건에서 수행되며, WGS, PSA의 후단공정을 통해 수소를 생산한다. 분리막 개질기를 이용한 SMR반응은 분리막이 수소를 제거함에 따라 반응효율 증진, 공정온도 저감, 후단공정 배제를 할 수 있어 공정구성 및 경제성이 우수하다. 본 연구에서는 팔라듐분리막 개질기를 사용하여 550°C, 5 bar에서 SMR반응을 통해 수소를 생산하였으며, 개질된 가스의 CO 농도를 최소화하여 고온 PEMFC용 연료처리장치를 개발하였다.

The potential application of palladium-ruthenium composite membranes to the separation of hydrogen from chlorosilane gases in silicon-based industries was investigated. Ru/Pd/Al2O3/PSS membranes were prepared by electroless plating. Hydrogen permeation tests and temperature programmed desorption analysis revealed that the addition of a Ru over layer on Pd changed the hydrogen adsorption characteristics, resulting in improved stability of the membrane at low temperatures. The Ru/Pd/Al2 O3/PSS composite membrane had a stable hydrogen permeation flux of 1.8 m3m-2h-1 over a period of 1,200 h at 180°C without suffering hydrogen embrittlement. After exposure to impurities such as HCl and SiHCl3 , the hydrogen permeation flux of the Ru/Pd/Al2 O3/PSS composite membrane was stable over a period of 9h with feed pressure of 2.0 bar at 225°C.

The recent rise in applications of thermoelectric materials has attracted interest in studies toward the fabrication of thermoelectric materials using mass production techniques. In this study, we successfully fabricate n-type Bi2Te2.7Se0.3 material by a combination of mass production powder metallurgy techniques, gas atomization, and spark plasma sintering. In addition, to examine the effects of hydrogen reduction in the microstructure, the thermoelectric and mechanical properties are measured and analyzed. Here, almost 60% of the oxygen content of the powder are eliminated after hydrogen reduction for 4 h at 360°C. Micrographs of the powder show that the reduced powder had a comparatively clean surface and larger grain sizes than unreduced powder. The density of the consolidated bulk using as-atomized powder and reduced atomized powder exceeds 99%. The thermoelectric power factor of the sample prepared by reduction of powder is 20% better than that of the sample prepared using unreduced powder.

Odor compounds and air-born microorganisms are simultaneously emitted from various aeration processes such as aerobic digestion, food-waste compositing, and carcass decomposition facilities that are biologically-treating wastes with high organic contents. The air streams emitted from these processes commonly contain sulfur-containing odorous compounds such as hydrogen sulfide(H2S) and bacterial bioaerosols. In this study, a wet-plasma method was applied to remove these air-born pollutants and to minimize safety issues. In addition, the effects of a gas retention time and a liquid-gas ratio were evaluated on removal efficiencies in the wet-plasma system. At the gas reaction time of 1.8 seconds and the liquid-gas ratio of 0.05 mLaq/Lg, the removal efficiency of bioaerosol was approximately 75 %, while the removal efficiency of H2S was lower than 20 %, indicating that the gaseous compound was not effectively oxidized by the plasma reaction at the low liquid addition. When the liquid-gas ratio was increased to 0.25 mLaq/Lg, the removal efficiencies of both H2S and bioaerosol increased to greater than 99 %. At the higher liquid-gas ratio, more ozone was generated by the wet-plasma reaction. The ozone generation was significantly affected by the input electrical energy, and it needed to be removed before discharged from the process.

For the hydrogen economy system being tried starting with the 21st century, the fields that was not dealt with so far, such as the safety measure for large leakage accidents, the safety problem at infrastructures like a hydrogen station, the safety problem in terms of automobiles depending on introduction of hydrogen cars, the safety problem in a supply for homes like fuel cells, etc., are being deeply reviewed. In order to establish a safety control system, an essential prerequisite in using and commercializing hydrogen gas as an efficient energy source, it is necessary to conduct an analysis, such as analysis of hydrogen accident examples, clarification of physical mechanisms, qualitative and quantitative evaluation of safety, development of accident interception technologies, etc. This study prepared scenarios of hydrogen gas leakage that can happen at hydrogen stations, and predicted damage when hydrogen leaks by using PHAST for this.

In this study, highly sensitive hydrogen micro gas sensors of the multi-layer and micro-heater type were designed and fabricated using the micro electro mechanical system (MEMS) process and palladium catalytic metal. The dimensions of the fabricated hydrogen gas sensor were about 5mm×4mm and the sensing layer of palladium metal was deposited in the middle of the device. The sensing palladium films were modified to be nano-honeycomb and nano-hemisphere structures using an anodic aluminum oxide (AAO) template and nano-sized polystyrene beads, respectively. The sensitivities (Rs), which are the ratio of the relative resistance were significantly improved and reached levels of 0.783% and 1.045 % with 2,000 ppm H2 at 70˚C for nano-honeycomb and nano-hemisphere structured Pd films, respectively, on the other hand, the sensitivity was 0.638% for the plain Pd thin film. The improvement of sensitivities for the nano-honeycomb and nano-hemisphere structured Pd films with respect to the plain Pd-thin film was thought to be due to the nanoporous surface topographies of AAO and nano-sized polystyrene beads.

Hydrogen has the very high heating value by comparing with other fuels and its combustion exhausts no carbon. But hydrogen causes the very high adiabatic flame temperature which generates thermal NOx. In this study, two cases of experiments were performed to compare engine characteristics. First and second cases are for only diesel combustion engine and mixed hydrogen diesel engine respectively. To verify the effect of mixed hydrogen-diesel combustion engine, the exhausted gas from modified dual fuel diesel engine was analyzed. In addition, diesel consumption per kWh for each case was estimated to validate its economic feasibility. By mixing hydrogen with 5kW brown(hydrogen-oxygen mixture) gas generator, the amount of CO(carbon mono-oxide) decreased from 330ppm to 210ppm by improving combustion and the amount of NOx increased from 390ppm to 520ppm by higher temperature of combustion chamber. Diesel consumption per kWh decreased from 450cc to 410cc but actually increased until 480cc because of the power of brown gas generator

This study is about the qualitative safety assessment for hydrogen gas filling facilities in Korea operating with one-bank type. The purpose of this safety assessment is about the development of components for design, fabrication, assembly, operability of dispenser and systems of the safety. For the qualitative safety assessment method, the study used FMEA(failure mode & effect analysis) and HAZOP(hazard & operability). This study evaluated the safety through FMEA and HAZOP then by referring to P&ID and PFD of hydrogen dispenser, thereby examining the dangerousness of the equipments, defects of the structure and problems of the operation.

팔라듐이 코팅된 V99.8B0.2 합금 분리막을 통해 sweep 가스를 사용하지 않고 수소 투과 시 혼합가스의 영향에 대해 알아보았다. 분리막은 400℃에서 sweep 가스를 사용하지 않고 순수 수소, 수소/이산화탄소, 수소/일산화탄소의 혼합가스를 1.5~8.0 bar의 압력으로 실험하였다. Sweep 가스를 사용하지 않고 수소만을 공급한 투과 실험에서 팔라듐 코팅된 V99.8B0.2 합금 분리막(두께 : 0.5 mm)의 수소 투과량은 40.7mL/min/㎠였다. 또한 수소/이산화탄소를 공급한 투과실험에서 V99.8B0.2 합금 분리막의 수소 투과량은 21.4mL/min/㎠였다. 수소/이산화탄소 및 수소/일산화탄소 혼합가스를 각각 공급할 때 투과량은 압력에 상관없이 수소 분압 감소 만큼 감소하였고 모든 경우 Sievert 법칙을 잘 만족시켰다. 투과 후 분리막의 XRD, SEM/EDX 결과로부터 V99.8B0.2 합금 분리막은 여러 혼합가스에 대해 안정성과 내구성이 우수하다는 것을 알 수 있었다.

ZnO thin films were prepared on a glass substrate by radio frequency (RF) magnetron sputtering without intentional substrate heating and then surfaces of the ZnO films were irradiated with intense electrons in vacuum condition to investigate the effect of electron bombardment on crystallization, surface roughness, morphology and hydrogen gas sensitivity. In XRD pattern, as deposited ZnO films show a higher ZnO (002) peak intensity. However, the peak intensity for ZnO (002) is decreased with increase of electron bombarding energy. Atomic force microscope images show that surface morphology is also dependent on electron bombarding energy. The surface roughness increases due to intense electron bombardment as high as 2.7 nm. The observed optical transmittance means that the films irradiated with intense electron beams at 900 eV show lower transmittance than the others due to their rough surfaces. In addition, ZnO films irradiated by the electron beam at 900 eV show higher hydrogen gas sensitivity than the films that were electron beam irradiated at 450 eV. From XRD pattern and atomic force microscope observations, it is supposed that intense electron bombardment promotes a rough surface due to the intense bombardments and increased gas sensitivity of ZnO films for hydrogen gas. These results suggest that ZnO films irradiated with intense electron beams are promising for practical high performance hydrogen gas sensors.