In this study, Y3Al5O12:Eu3+ red phosphors were synthesized at different temperatures using a solid state reaction method. The crystal structures, surface and optical properties of the Y3Al5O12:Eu3+ red phosphors were investigated using Xray diffraction (XRD), field emission scanning electron microscope (FE-SEM), and photoluminescence (PL) analyses. From XRD results, the crystal structure of the Y3Al5O12:Eu3+ red phosphors was determined to be cubic. The maximum emission spectra were observed for the Y3Al5O12:Eu3+ red phosphor prepared by annealing for 4h at 1,700 oC. The 565~590 nm photoluminescent spectra of the Y3Al5O12:Eu3+ red phosphors is associated with the 5D0 → 7F2 magnetic dipole transition of the Eu3+ ions. The intensity of the photoluminescent spectra in the red phosphors is more dominant for the magnetic dipole transition than the electric dipole transition with increasing annealing temperature. The International Commission on Illumination (CIE) coordinates of Y3Al5O12:Eu3+ red phosphors prepared by 1,700 oC annealing temperature are X = 0.5994, Y = 0.3647.

Environmental issues such as global warming due to fossil fuel use are now major worldwide concerns, and interest in renewable and clean energy is growing. Of the various types of renewable energy, green hydrogen energy has recently attracted attention because of its eco-friendly and high-energy density. Electrochemical water splitting is considered a pollution-free means of producing clean hydrogen and oxygen and in large quantities. The development of non-noble electrocatalysts with low cost and high performance in water splitting has also attracted considerable attention. In this study, we successfully synthesized a NiCo2O4/NF electrode for an oxygen evolution reaction in alkaline water splitting using a hydrothermal method, which was followed by post-heat treatment. The effects of heat treatment on the electrochemical performance of the electrodes were evaluated under different heat-treatment conditions. The optimized NCO/NF-300 electrode showed an overpotential of 416 mV at a high current density of 50 mA/cm2 and a low Tafel slope (49.06 mV dec-1). It also showed excellent stability (due to the large surface area) and the lowest charge transfer resistance (12.59 Ω). The results suggested that our noble-metal free electrodes have great potential for use in developing alkaline electrolysis systems.

Recently, considerable attention has been given to nickel-based superalloys used in additive manufacturing. However, additive manufacturing is limited by a slow build rate in obtaining optimal densities. In this study, optimal volumetric energy density (VED) was calculated using optimal process parameters of IN718 provided by additive manufacturing of laser powder-bed fusion. The laser power and scan speed were controlled using the same ratio to maintain the optimal VED and achieve a fast build rate. Cube samples were manufactured using seven process parameters, including an optimal process parameter. Analysis was conducted based on changes in density and melt-pool morphology. At a low laser power and scan speed, the energy applied to the powder bed was proportional to and not . At a high laser power and scan speed, a curved track was formed due to Plateau-Rayleigh instability. However, a wide melt-pool shape and continuous track were formed, which did not significantly affect the density. We were able to verify the validity of the VED formula and succeeded in achieving a 75% higher build rate than that of the optimal parameter, with a slight decrease in density and hardness.

Tungsten disulfide (WS2) nanosheets have attracted considerable attention because of their unique optical and electrical properties. Several methods for fabrication of WS2 nanosheets have been developed. However, methods for mass production of high-quality WS2 nanosheets remain challenging. In this study, WS2 nanosheets were fabricated using mechano-chemical ball milling based on the synergetic effects of chemical intercalation and mechanical exfoliation. The ball-milling time was set as a variable for the optimized fabricating process of WS2 nanosheets. Under the optimized conditions, the WS2 nanosheets had lateral sizes of 500–600 nm with either a monolayer or bilayer. They also exhibited high crystallinity in the 2H semiconducting phase. Thus, the proposed method can be applied to the exfoliation of other transition metal dichalcogenides using suitable chemical intercalants. It can also be used with highperformance WS2-based photodiodes and transistors used in practical semiconductor applications.

AlSi10Mg alloys are being actively studied through additive manufacturing for application in the automobile and aerospace industries because of their excellent mechanical properties. To obtain a consistently high quality product through additive manufacturing, studying the flowability and spreadability of the metal powder is necessary. AlSi10Mg powder easily forms an oxide film on the powder surface and has hydrophilic properties, making it vulnerable to moisture. Therefore, in this study, AlSi10Mg powder was hydrophobically modified through silane surface treatment to improve the flowability and spreadability by reducing the effects of moisture. The improved flowability according to the number of silane surface treatments was confirmed using a Carney flowmeter. In addition, to confirm the effects of improved spreadability, the powder prior to surface treatment and that subjected to surface treatment four times were measured and compared using s self-designed recoating tester. The results of this study confirmed the improved flowability and spreadability based on the modified metal powder from hydrophilic to hydrophobic for obtaining a highquality additive manufacturing product.

바이오산업의 발전으로 의약품, 식품 등의 생산 과정의 분리/정제 공정에 사용되어 왔던 기존의 컬럼 크로마토그 래피를 대체하여 더 높은 처리효율을 갖는 막 크로마토그래피가 부상하고 있다. 본 연구에서는 서로 다른 기공 크기의 두 가 지 상용 셀룰로오스 아세테이트(Cellulose acetate, CA) 분리막을 탈아세틸화 과정을 통해, 리간드의 개질이 용이한 다공성 재 생 셀룰로오스 지지체를(Regenerated cellulose, RC) 제조하였다. 음이온 교환능을 부여하고자 grafting을 수행하였으며, 구체 적으로는 UV 중합법을 통해 4차 암모늄을 포함하는 음이온 교환 리간드(MAPTAC)를 부착하여 음이온 교환용 흡착막을 제 조하였다. 단백질 흡착 용량은 정적 흡착 용량(Static binding capacity, SBC)시험을 통해 총 단백질 흡착 용량을 측정했고, 동 적 흡착 용량(Dynamic binding capacity, DBC)을 측정하여 상용막과 비교 평가하였다. 성능 평가 결과 단백질 흡착량은 넓은 표면적에 의해 리간드 밀도가 높은, 기공 크기가 작은 순서로 높게 측정되었고, 상용 CA분리막을 탈아세틸화하고 리간드를 부착시킨 분리막(RC 0.8 + MAPTAC 43.69 mg/ml, RC 3.0 + MAPTAC 36.33 mg/ml)이 상용 막 크로마토그래피 제품(28.38 mg/ml) 대비 높은 흡착 용량을 보였다.

The recycling of solid waste materials to fabricate carbon-based electrode materials is of great interest for low-cost green supercapacitors. In this study, porous carbon foam (PCF) was prepared from waste floral foam (WFF) as an electrode material for supercapacitors. WFF was directly carbonized at various temperatures of 600, 800, and 1,000 oC under an inert atmosphere. The WFF-derived PCF (C-WFF) was found to have a specific surface area of 458.99 m2/g with multi-modal pore structures. The supercapacitive behavior of the prepared C-WFF was evaluated using a three-electrode system in a 6 M KOH aqueous electrolyte. As a result, the prepared C-WFF as an active material showed a high specific capacitance of 206 F/g at 1 A/g, a rate capability of 36.4 % at 20 A/g, a specific power density of 2,500 W/kg at an energy density of 2.68 Wh/kg, and a cycle stability of 99.96 % at 20 A/g after 10,000 cycles. These results indicate that the C-WFF prepared from WFF could be a promising candidate as an electrode material for high-performance green supercapacitors.

In recent years, ESG activities (Environment, Social and Governance) have been paid more and more attention by enterprises and their stakeholders in various countries. China is the largest developing country in the world. The ESG performance of Chinese listed enterprises helps to understand the shortcomings of their sustainable development ability and further enhance the firm value. Moreover, the interaction effect between green innovation investment and ESG activities is of great significance for enterprises to balance the resource allocation between the two factors in the future. Taking listed Chinese manufacturing companies from 2011 to 2020 as an example, this study investigates the influence of ESG activities on financial performance and non-financial performance, and tests the moderating role of green innovation. Our results show that: (1) ESG performance has a negative impact on financial performance; (2) ESG performance has a positive impact on non-financial performance; (3) Green innovation can positively adjust the negative impact of environmental activities on financial performance. However, it will enhance the negative impact of governance activities on financial performance. The interaction effect between green innovation and social activities on corporate financial performance is a substitution effect; (4) With the improvement of green innovation level, the positive impact of ESG overall performance and environmental performance on corporate reputation will also be suppressed.

The purpose of this study is to suggest a plan to improve the level of acceptance of related technologies and the transition to smart factories of small and medium-sized manufacturing enterprises by using ‘technology readiness’ and ‘integrated technology acceptance model’. To this end, the research hypothesis was verified by collecting questionnaire data from 130 small and medium- sized manufacturing companies in Korea and conducting path analysis. First, optimism affects performance expectations, social influence, and facilitation conditions, innovation affects performance expectations, effort expectations, and social influence, discomfort affects performance expectations, social influence, and facilitation conditions, and anxiety affects effort expectations, social influence and facilitation conditions. has been proven to affect Finally, performance expectations, effort expectations, social influence, and facilitation conditions were verified to have a significant positive effect on the intention to accept technology.

본 연구는 제조업 남성 근로자들의 직무스트레스와 피로와의 관계에서 사회적 지지의 매개효과를 검토하는 것을 목적으로 수행하였다. 대상: 조사대상은 제조업 공장에 근무하는 남성 근로자 352명이었다. 방법: 자료 수집은 2020년 4월 1일부터 5월 31일까지의 기간 동안에 구조화된 자기기입식 설문지를 이용한 설문조사에 의하였다. 수집된 자료는 SPSS 23.0 통계프로그램을 사용하여 상관분석, 위계적 회귀분석 및 Sobel test로 분석하였다. 결과: 연구결과, 조사대상자의 피로증상은 업무요구도와 유의한 양의 상관관계를 보인 반면, 업무의 자율성, 상자의 지지 및 동료의 지지와는 유의한 음의 상관관계를 보였다. 직무스트레스와 피로와의 관계에서 사회적 지지의 매개효과를 검증한 결과, 직무스트레스가 높을수록 사회적 지지는 낮아지는 것으로 나타났으며(F=63.93, p<0.01), 피로수준은 높아지는 것으로 나타났다(F=58.64, p<0.01). 직무스트레스를 통제한 상태에서 사회적지지가 피로에 미치는 영향 또한 통계적으로 유의하였으며(F=43.83, p<0.01), 이 때 직무스트레스의 β값이 0.352로 매개변수를 거치지 않았을 때의 β값인 0.545보다 작아 사회적지지가 매개효과를 가지는 것으로 나타났다. Sobel test 결과에서 사회적 지지는 직무스트레스와 피로의 관계에서 부분적 매개역할을 하였다(Z=-4.15, p<0.01). 결론: 위와 같은 결과는 직장에서의 사회적 지지는 근로자의 피로와 관련 있는 직무스트레스를 완화시키는 매개효과가 있을 가능성을 시사한다.

본 연구의 목적은 효소 가수분해 및 유산균 혼합발효기술을 이용하여 GABA 함량이 강화된 발효 다시마 추출물을 생산함에 있다. TLC 분석방법을 통해 GABA 생성능력이 우수한 균주 L. plantarum KCTC 21004, L. acidophilus KCTC 3164, L. sakei subsp. sakei KCTC 3598를 선정하였 다. 선정된 균주를 이용한 유산균 발효의 특성은 배양 시간이 증가 할수록 적정 산도는 증가하였고 pH 는 감소하는 경향을 나타내었다. GABA 생성능력이 우수한 3종의 균주 중 L. plantarum KCTC 21004 이 GABA 함량이 136.4 mg/100g으로 우수하였다. 이러한 연구 결과는 유산균을 이용한 GABA 생산과 정에 있어서 기초적인 자료로 제공될 것으로 판단된다.

Lightweight steel is a crucial material that is being actively studied because of increased carbon emissions, tightening regulations regarding fuel efficiency, and the emergence of UAM, all of which have been recently labeled as global issues. Hence, new strategies concerning the thickness and size reduction of steel are required. In this study, we manufacture lightweight steel of the Fe-Mn-Al-C system, which has been recently studied using the DED process. By using 2.8 wt.% low-Mn lightweight steel, we attempt to solve the challenge of joining steel parts with a large amount of Mn. Among the various process variables, the laser scan power is set at 600 and 800W, and the laser scan speed is fixed at 16.67 mm/s before the experiments. Several pores and cracks are observed under both conditions, and negligibly small pores of approximately 0.5 μm are observed.

In this study, additive manufacturing of a functionally graded material (FGM) as an alternative to joining dissimilar metals is investigated using directed energy deposition (DED). FGM consists of five different layers, which are mixtures of austenitic stainless steel (type 316 L) and low-alloy steel (LAS, ferritic steel) at ratios of 100:0 (A layer), 75:25 (B layer), 50:50 (C layer), 25:75 (D layer), and 0:100 (E layer), respectively, in each deposition layer. The FGM samples are successfully fabricated without cracks or delamination using the DED method, and specimens are characterized using optical and scanning electron microscopy to monitor their microstructures. In layers C and D of the sample, the tensile strength is determined to be very high owing to the formation of ferrite and martensite structures. However, the elongation is high in layers A and B, which contain a large fraction of austenite.

A Cu-15Ag-5P filler metal (BCuP-5) is fabricated on a Ag substrate using a high-velocity oxygen fuel (HVOF) thermal spray process, followed by post-heat treatment (300oC for 1 h and 400oC for 1 h) of the HVOF coating layers to control its microstructure and mechanical properties. Additionally, the microstructure and mechanical properties are evaluated according to the post-heat treatment conditions. The porosity of the heat-treated coating layers are significantly reduced to less than half those of the as-sprayed coating layer, and the pore shape changes to a spherical shape. The constituent phases of the coating layers are Cu, Ag, and Cu-Ag-Cu3P eutectic, which is identical to the initial powder feedstock. A more uniform microstructure is obtained as the heat-treatment temperature increases. The hardness of the coating layer is 154.6 Hv (as-sprayed), 161.2 Hv (300oC for 1 h), and 167.0 Hv (400oC for 1 h), which increases with increasing heat-treatment temperature, and is 2.35 times higher than that of the conventional cast alloy. As a result of the pull-out test, loss or separation of the coating layer rarely occurs in the heat-treated coating layer.