Al-Si-SiC composite powders with intra-granular SiC particles were prepared by a gas atomization process. The composite powders were mixed with Al-Zn-Mg alloy powders as a function of weight percent. Those mixture powders were compacted with the pressure of 700 MPa and then sintered at the temperature of 565-585˚C. T6 heat treatment was conducted to increase their mechanical properties by solid-solution precipitates. Each relative density according to the optimized sintering temperature of those powders were determined as 96% at 580˚C for Al-Zn-Mg powders (composition A), 97.9% at 575˚C for Al-Zn-Mg powders with 5 wt.% of Al-Si-SiC powders (composition B), and 98.2% at 570˚C for Al-Zn-Mg powders with 10 wt.% of Al-Si-SiC powders (composition C), respectively. Each hardness, tensile strength, and wear resistance test of those sintered samples was conducted. As the content of Al-Si-SiC powders increased, both hardness and tensile strength were decreased. However, wear resistance was increased by the increase of Al-Si-SiC powders. From these results, it was confirmed that Al-Si-SiC/Al-Zn-Mg composite could be highly densified by the sintering process, and thus the composite could have high wear resistance and tensile strength when the content of Al-Si-SiC composite powders were optimized.

In this paper, we describe experiment results using a vibration assisted hybrid femtosecond laser (λ:795 nm) ultra- precision machining system. The hybrid system we have developed is possible that optical focal point of the femtosec- ond laser constantly and frequently within the range of PZT(piezoactuator) vibrator working distance. Using the hybrid system, We have experimented on brass and studied about differences of result of hole aspect ratio compare to general experiment setup of femtosecond laser system. Aspect ratio of a micro hole on brass is increased as 54% with 100 Hz vibration frequency and surface roughness of the side wall also improved compare to non-vibration.

The effect of a sputter deposition sequence of Cu, Zn, and Sn metal layers on the properties of Cu2ZnSnS4 (CZTS) was systematically studied for solar cell applications. The set of Cu/Sn/Zn/Cu multi metal films was deposited on a Mo/SiO2/Si wafer using dc sputtering. CZTS films were prepared through a sulfurization process of the Cu/Sn/Zn/Cu metal layers at 500˚C in a H2S gas environment. H2S (0.1%) gas of 200 standard cubic centimeters per minute was supplied in the cold-wall sulfurization reactor. The metal film prepared by one-cycle deposition of Cu(360 nm)/Sn(400 nm)/Zn(400 nm)/Cu(440 nm) had a relatively rough surface due to a well-developed columnar structure growth. A dense and smooth metal surface was achieved for two- or three-cycle deposition of Cu/Sn/Zn/Cu, in which each metal layer thickness was decreased to 200 nm. Moreover, the three-cycle deposition sample showed the best CZTS kesterite structures after 5 hr sulfurization treatment. The two- and three-cycle Cu/Sn/Zn/Cu samples showed high-efficient photoluminescence (PL) spectra after a 3 hr sulfurization treatment, wheres the one-cycle sample yielded poor PL efficiency. The PL spectra of the three-cycle sample showed a broad peak in the range of 700-1000 nm, peaked at 870 nm (1.425 eV). This result is in good agreement with the reported bandgap energy of CZTS.

PVA와 PAA블랜드의 용액주조법을 통하여 겔 고분자 전해질막이 제조되었다. 블랜드 내의 PAA함량은 30에서 80 wt% 사이 범위에서 조절되었다. 겔 고분자 전해질을 이용하여 아연공기전지를 제작하였다. 제조된 겔 고분자 전해질의 기계적, 전기적 특성을 인장실험과 임피던스 실험을 통하여 측정하였다. 아연공기전지의 성능은 current interrupt method와 정전류 방전실험을 통하여 측정하였다. 겔 고분자 전해질 내의 PAA함량이 증가함에 따라 인장강도 및 인장탄성계수가 감소하였다. 반면, PAA함량의 증가에 따라 겔 고분자 전해질막의 이온전도도는 증가하였다. 이와 같은 이온전도도의 증가의 아연공기전지 내에서의 효과는 current interrupt method와 정전류 방전실험에서 확인되었다. PAA함량이 높은 겔 전해질막으로 제조된 전지는 낮은 IR손실과 높은 방전용량을 보였다.

[ Zn2(1-x)MnxSiO4 ]0.07≤x≤0.15) green phosphor was prepared by solid state reaction. The first heating was at 900˚C-1250˚C in air for 3 hours and the second heating was at 900˚C in N2/H2(95%/5%) for 2 hours. The size effect of SiO2 in forming Zn2SiO4 was investigated. The temperature for obtaining single phase Zn2SiO4 was lowered from 1100˚C to 1000˚C by decreasing the SiO2 particle size from micro size to submicro size. The effect of the activators for the Photoluminescence (PL) intensity of Zn2SiO4:Mn2+ was also investigated. The PL intensity properties of the phosphors were investigated under vacuum ultraviolet excitation (147 nm). The emission spectrum peak was between 520 nm and 530 nm, which was involved in green emission area. MnCl2·4H2O, the activator source, was more effective in providing high emission intensity than MnCO3. The optimum conditions for the best optical properties of Zn2SiO4:Mn2+ were at x = 0.11 and 1100˚C. In these conditions, the phosphor particle shape was well dispersed spherical and its size was 200 nm.

In order to make a (CZTSe) sputtering target sintered for solar cell application, synthesis of CZTSe compound by solid state reaction of Cu, Zn, Sn and Se mixed powders and effects of ball milling condition on sinterability such as ball size, combination of ball size, ball milling time and sintering temperature, was investigated. As a result of this research, sintering at after ball milling using mixed balls of 1 mm and 3 mm for 72 hours was the optimum condition to synthesis near stoichiometric composition of and to prepare sintered pellet with high density relatively.

For the aim of low-temperature co-fired ceramic microwave components, sintering behavior and microwave properties (dielectric constant , quality factor Q, and temperature coefficient of resonant frequency ) are investigated in [BCZN] ceramics with addition of . The specimens are prepared by conventional ceramic processing technique. As the main result, it is demonstrated that the additives () show the effect of lowering of sintering temperature and improvement of microwave properties at the optimum additive content. The addition of 0.25 wt% lowers the sintering temperature to utilizing liquidphase sintering and show the microwave dielectric properties (dielectric constant = 75, quality factor = 572 GHz, temperature coefficient of resonance frequency ). The estimated microwave dielectric properties with addition (increase of , decrease of , shift of to negative values) can be explained by the observed microstrucure (sintered density, abnormal grain structure) and possibly high-permittivity (BZN) phase determined by X-ray diffraction.

A study was conducted to determine the effects of the cattle manure (CM) application on the botanical composition and micro-mineral contents (Fe, Mn, Cu, Zn) of grazing pasture at the experimental field of Livestock Division, Subtropical Animal Experiment Station, National Institute of Animal Science from year 2003 to 2005. The experiment was arranged in a randomized complete block design with three replications. The treatment consisted of T1: 100% chemical fertilizer (CF 100%), T2: 50% CF +50% CM, T3: 25% CF +75% CM, T4: 100% cattle manure (CM 100%), T5: 100% CM (1st yr.)+ 100% CF (2nd yr.) + 100% CM (3rd yr.), T6: 100% CM (1st yr.)+ 100% CF (2nd yr.)+ 100% CF (3rd yr.). The botanical composition of grassland for grass, legumes, and weeds showed that the rate of legumes was increased in all treatments. The weeds rate in T4 was the highest in comparison to the other treatments. For micro-mineral contents T5 showed the highest average Fe contents of 262.08 ppm and T1 showed the lowest (199.20 ppm). Mn contents was the highest in T1 among the other treatments. Zn contents was the highest in T3 as compared with other treatments. Cu contents was the highest in T6 as compared with other treatments. The results of this experiments indicated that micro-mineral contents of change was effect of legumes increased than treatment

The long-period stacking order (LPSO) structures and stacking faults (SFs) in rapidly solidified powder metallurgy (RS P/M) Mg97Zn1Y2 alloy were investigated by high resolution transmission electron microscopy (HRTEM) observations. The 18R-type LPSO structure with a stacking sequence of ACBCBCBACACACBABAB and a period of 4.86 nm was observed in the as-extruded RS P/M Mg97Zn1Y2 alloy. After annealing at 773 K for 5 hr, the 18R-type LPSO structure was transformed to the 14H-type LPSO structure with a stacking sequence of ABABABACBCBCBC and a period of 3.64 nm. The 24R-type LPSO structure containing 24 atomic layers of ABABABABCACACACABCBCBCBC with period of 6.18 nm coexists with the 14H-type LPSO structure in the same grains. The LPSO structures contain intrinsic Type II SFs such as BCB/CABA and ABA/CBCB stacking sequences of a closely packed plane.

In this paper, non-treated ACF (Activated Carbon Fiber) /TiO2 and Zn-treated ACF/TiO2 were prepared. The prepared composites were characterized in terms of their structural crystallinity, elemental identification and photocatalytic activity. XRD patterns of the composites showed that the non-treated ACF/TiO2 composite contained only typical single and clear anatase forms while the Zn-treated ACF/TiO2 contained a mixed anatase and rutile phase with a unique ZnO peak. SEM results show that the titanium complex particles are uniformly distributed on and around the fiber and that the titanium complex particles are more regularly distributed on and around the ACF surfaces upon an increase of the ZnCl2 concentration. These EDX spectra show the presence of peaks from the C, O and Ti elements. Moreover, peaks of the Zn element were observed in the Zn-treated ACF/TiO2 composites. The prominent photocatalytic activity of the Zn-treated ACF/TiO2 can be attributed to the three different effects of photo-degradation: doping, absorptivity by an electron transfer, and adsorptivity of porous ACFs between the Zn-TiO2 and Zn-ACF.

Mg-4.3Zn-0.7Y (at%) alloy powders were prepared using an industrial scale gas atomizer, followed by warm extrusion. The powders were almost spherical in shape. The microstructure of atomized powders and those extruded bars was examined using Scanning Electron Microscopy (SEM), Energy Dispersive X-ray Spectroscope (EDS) and X-ray Diffractometer (XRD). The grain size of the powders was coarsen as the initial powder size increased. After the extrusion, the grain size became fine due to the severe plastic deformation during the extrusion with the ratio of 10:1. Both the ultimate strength and elongation were enhanced with the decrease of initial particle size.

Fabrication of bulk alloy has been performed through the consolidation of rapidly solidified ribbons. The bulk alloy exhibited excellent mechanical properties, high tensile yield strength of 530 MPa, and large elongation of 3 %. Microstructure of the alloy was characterized by equiaxed fine grains that consist of -Mg, long period ordered (LPO) structure phase, and -type cubic compound. The strengthening of the alloys may be due to fine grains with LPO structure phase and -type compound.

The microstructure and mechanical properties of the alloy prepared by spark plasma sintering of gas atomized powders have been investigated. After consolidation, precipitates were observed to form in the solid solution matrix of the alloy. These precipitates consisted of and phases. The density of the consolidated bulk Mg-Zn-Y alloy was . The ultimate tensile strength and elongation were dependent on the consolidation temperature, which were in the ranges of 280 to 293 MPa and 8.5 to 20.8 %, respectively.

Various kinds of Mg-Zn-Ca base alloys were rapidly quenched via melt spinning process. The meltspun ternary and quaternary alloy ribbons were heat-treated, and then the effects of additional elements on age hardening behavior and phase change of precipitates were investigated using Vickers hardness tester, XRD, and TEM equipped with EDS system. In ternary alloys, age hardening was mostly due to the distribution of and . The stable phases of precipitates were varied according to the aging temperature and the alloy composition. With the increase of Ca content, precipitates were detected more than precipitates. In quaternary alloys, the precipitates taken from Mg-Zn-Ca-Co were identified as new quaternary phase, whereas those taken from Mg-Zn-Ca-Zr as MgZnCa containing Zr. In general, the ternary alloy showed higher peak hardness and thermal stability than the quaternary considering the total amounts of the solutes. It implies that the structure of precipitate should be controlled to have the coherent interface with the Mg matrix.

Abstract Direct solid state synthesis by hot pressing has been applied in order to produce high efficiency bulk specimens. Single phase with 98.5% of theoretical density was successfully produced by direct hot pressing of elemental powders containing 1.2 at.% excess Zn. Thermoelectric properties as a function of temperature were investigated from room temperature to 600 K and compared with results of other studies. Transport properties at room temperature were also evaluated. Thermoelectric properties of single phase materials produced by direct synthesis were measured and are comparable to the published data. Direct solid state synthesis by hot pressing provides a promising processing route in this material