본 시험에서는 블루베리 양액재배시 양분공급시기가 수체 생육과 과실품질에 어떤 영향을 미치는지 알아보고자 수행하였다. 신초생장은 1차, 2차 생장량은 비슷한 경향이었으나, 3 차 생장량은 수확종료 15일 전 중단한 처리에 비해 수확종료 직후와 수확종료 후 15일에 공급을 중단한 처리가 각각 15.4%, 15.6% 생장을 많이 하는 경향이었고, 수확종료 후 60 일에 양분공급을 중단한 처리는 수확종료 15일전에 중단한 처리보다 3차 생장량이 53.2% 증가하는 경향이었다. 양액공급 후 이듬해 꽃눈수를 조사한 결과 수확종료 후 60일에 양분 공급을 중단한 처리는 수확종료 15일전에 중단한 처리보다 26% 적었다. 처리별 과실특성은 과실중, 당도, 산도 등은 처리 간 큰 차이가 없었으며, 주당 수량은 수확종료 15일전이 2.1kg, 수확종료 직후와 수확종료 후 15일에 양분을 중단한 처리가 2.5kg으로 가장 많았으며, 수확종료 후 45일과 60일에 양분을 중단한 처리는 1.8kg으로 가장 작았다.

Due to global climate change, mega-droughts have occurred frequently. Since long-term droughts make it difficult to secure the water resources, water supply needs to be restricted in a reasonable manner. In the event of limited water supply, the waterworks need to develop a restricted water supply strategy. This study showed that analyzing daily water supply could be used to respond to the first stage of a drought. According to an analysis of Korea's major water authorities, there was about 7~21% of room for daily minimum water supply in case of a drought. Restricting the water supply by lowering pressure is a good strategy for local water authorities with high water leakage rate since leakage is inversely dependent with pressure. For this method, it is necessary to quantify water deficiency and pressure at each node using a simulation. Since DDA-based software is not possible to predict changes in demand at nodes with pressure reduction, WaterGEMS, a PDA software, was used to quantitatively predict water shortages and pressures at each node. Locations where water is deficient need to install booster pumps or to be dispatched with water tank truck and bottled water. Without these support, lowering pressure could not be an option for water works. This paper suggests a method for waterworks to plan a drought by lowering pressure to restrict water supply using daily water supply analysis and PDA based simulation.

In this study, a model to optimize residual chlorine concentrations in a water supply system was developed using a multi-objective genetic algorithm. Moreover, to quantify the effects of optimized residual chlorine concentration management and to consider customer service requirements, this study developed indices to quantify the spatial and temporal distributions of residual chlorine concentration. Based on the results, the most economical operational method to manage booster chlorination was derived, which would supply water that satisfies the service level required by consumers, as well as the cost-effectiveness and operation requirements relevant to the service providers. A simulation model was then created based on an actual water supply system (i.e., the Multi-regional Water Supply W in Korea). Simulated optimizations were successful, evidencing that it is possible to meet the residual chlorine concentration demanded by consumers at a low cost.

Cattle feeding in South Korea has been heavily dependent on domestically produced rice straw and imported grain. Around 42% of domestically produced rice straw is utilized for forage, and the remainder is recycled to restore soil fertility. Approximately 35% of round baleages were made with rice straw. However, higher quality hay is desired over rice straw. Due to increasing stockpiles of rice, there has been an economic burden on the government to store the surplus; therefore production of annual forage crops in rice fields has been further promoted in recent years. Hay import from the USA currently constitutes more than 80% of total imported hays. The main imported hays are alfalfa (Medicago sativa), timothy (Phleum pretense), and tall fescue (Festica arundinacea). The estimated forage required for cattle feeding was approximately 5.4 million MT in 2016. Domestically produced forage sates only 43% of that value, while low quality rice straw and imported hay covered the rest of demand by 33% and 20%, respectively. As utilization of domestically produced forage is more desirable for forage-based cattle production, long-term strategies have been necessary to promote domestic production of high quality baleage. One such strategy has been utilizing the fertile soil and abundance of fallow rice fields of western region of S. Korea to produce forage crops. Italian ryegrass (Lolium multiflorum) is the most successfully produced winter annual in the region and is approximately 56% of the total winter annual forage production. Forage sorghums (Sorghum bicolor), sorghum × sudangrass hybrids, and hybrid corn (Zea mays) produce a substantial amount of warm-season forage during summer. Produced forage has been largely stored through baleage due to heavy dew and frequent rains and has been evaluated according to S. Korea’s newly implemented baleage commodity evaluation system. The system weighs 50% of its total grading points on moisture content because of its importance in deliverable DM content and desirable baleage fermentation; this has proved to be an effective method. Although further improvement is required for the future of forage production in South Korea, the current government-led forage production in rice fields has been able to alleviate some of the country’s shortage for quality hay.

Korean firms have been vigorously searching and exploring overseas market opportunities through export and overseas investment. As of end of 2019, there were more than 80,000 Korean overseas subsidiaries all over the world. With Korean overseas direct investment increasing recently, it became one of the important issues for overseas investors to be successful in the global market. There are a lot of studies on factors influencing the performance of overseas subsidiaries such as ‘firm’ and ‘country’ factors. This study empirically examines subsidiary performance determinants with ‘industry architectures’ by using a sample of 292 overseas Korean firm subsidiaries. Industry architectures are the stable but evolving sets of rules and roles through which labor is divided within a sector. This article considers how industry architectures shape success in international expansion. Industry architectures differ between countries, are not necessarily technologically determined, shape firms’ capabilities and their competitive environment, and constitute a distinct level of analysis. We extract antecedents of related theory and empirically test its impact with a survey of Korean firms expanding in emerging economies. We would say this is the first study which tries to focus on industry architectures with the performance of Korean overseas subsidiaries. We find that separability and similarity of industry architectures across countries and localization of subsidiaries are robust and important predictors of success in international expansion. Our results suggest that industry architectures should be added to firm and country as an intermediate level of analysis that helps explain success in international expansion. While we established a pattern, much more remains to be done. We focus on the success of foreign operations, but we do not consider the broader benefits of going abroad, such as the learning or network effects that accrue at the level of the entire firm. The next obvious question is whether the results would differ in the developed market context. These we leave for future research to consider.

Supply chain managers seek to achieve global optimization by solving problems in the supply chain's business process. However, companies in the supply chain hide the adverse information and inform only the beneficial information, so the information is distorted and cannot be the information that describes the entire supply chain. In this case, supply chain managers can directly collect and analyze supply chain activity data to find and manage the companies described by the data. Therefore, this study proposes a method to collect the order-inventory information from each company in the supply chain and detect the companies whose data characteristics are explained through deep learning. The supply chain consists of Manufacturer, Distributor, Wholesaler, Retailer, and training and testing data uses 600 weeks of time series inventory information. The purpose of the experiment is to improve the detection accuracy by adjusting the parameter values of the deep learning network, and the parameters for comparison are set by learning rate (lr = 0.001, 0.01, 0.1) and batch size (bs = 1, 5). Experimental results show that the detection accuracy is improved by adjusting the values of the parameters, but the values of the parameters depend on data and model characteristics.

In this study, we developed a learning progression for the structure of the solar system using multi-tier supply form items and validated its appropriateness. To this end, by applying Wilson’s (2005) construct modeling approach, we set up ‘solar system components,’ ‘size and distance pattern of solar system planets,’ and ‘solar system modeling’ as the progress variables of the learning progression and constructed multi-tier supply form items for each of these variables. The items were applied to 150 fifth graders before and after the classes that dealt with the ‘solar system and star’ unit. To describe the results of the assessment, the students’ responses to each item were categorized into five levels. By analyzing the Wright map that was created by applying the partial credit Rasch model, we validated the appropriateness of the learning progression based on the students’ responses. In addition, the validity of the hypothetical pathway that was established in the learning progression was verified by tracking changes in the developmental level of students before and after the classes. The results of the research are as follows. The bottom-up research method that used multi-tier supply form items was able to elaborately set the empirical learning progression for the conceptualization of the structure of the solar system that is taught in elementary school. In addition, the validity of the learning progression was high, and the development of students was found to change with the learning progression.

The cooking-generated particles are major indoor sources of air pollution. Recently, the performance of the range hood is focused on particle removal performance. Range hood with an auxiliary air supply system can improve the fine and ultrafine particles removal efficiency by making a supply air during cooking activities. The particles were measured in the experimental building by varying ventilation types. Only operating range hood during the cooking activities was not enough to reduce the cooking-generated particles. Despite operating range hood systems, fine and ultrafine particle concentrations were maintained when cooking was finished. The range hood with a make-up air supply system can reduce the indoor particle concentration below background conditions when those systems were operated after cooking. In this study, the assessment of cooking-generated particle removal efficiency of the range hood with an auxiliary air supply system was conducted. The removal efficiency of ultrafine particles showed trends similar to the removal efficiency of fine particles.

Many companies make considerable efforts in implementing supply chain management systems to increase their competitiveness. In particular, there are significant investments in their ICT (Information and Communication Technology) and supply chain. However, considerable diversity exists in how well firms have been able to assimilate ICT and leverage the business value of it. In addition, studies on supply chains, particularly Real Time Enterprise (RTE) competence, which is cited for rapid information sharing and dynamic capabilities for each role in the supply chain, are insufficient. The purpose of this paper is to explore and evaluate effect of ICT utilization capabilities, including ‘ICT internal cooperative capabilities’ and ‘ICT operational flexibility capabilities’, on RTE capabilities (flexibility, visibility and prediction) and supply chain performance. To validate the research model proposed in the study, survey was conducted on companies using ICT along the supply chain of manufacturing industries. 216 data were used, SPSS and AMOS were used for the analysis methods. Study results showed that ICT internal collaboration capabilities affect agility, one of RTE capabilities, but not visibility and prediction, and ICT operational flexibility capabilities have affected all three RTE capacities. And, RTE capabilities had a huge impact on supply chain performance as expected. In this paper, it has been found that the ICT capabilities in manufacturing are an important factor in improving RTE capabilities that are important in the supply chain and improving the performance of the supply chain.

Maintenance of power distribution facilities is a significant subject in the power supplies. Fault caused by deterioration in power distribution facilities may damage the entire power distribution system. However, current methods of diagnosing power distribution facilities have been manually diagnosed by the human inspector, resulting in continuous pole accidents. In order to improve the existing diagnostic methods, a thermal image analysis model is proposed in this work. Using a thermal image technique in diagnosis field is emerging in the various engineering field due to its non-contact, safe, and highly reliable energy detection technology. Deep learning object detection algorithms are trained with thermal images of a power distribution facility in order to automatically analyze its irregular energy status, hereby efficiently preventing fault of the system. The detected object is diagnosed through a thermal intensity area analysis. The proposed model in this work resulted 82% of accuracy of detecting an actual distribution system by analyzing more than 16,000 images of its thermal images.

Due to global climate change, Korea is experiencing flooding and drought severely. It is hard to manage water resources because intensive precipitation during short periods and drought are commonly occurred in Korea, recently. Severe drought occurred in 2015 and 2017 in the islands, and coastal and inland areas in Korea, and the citizens experienced decreased water supply and emergency water service by using bottled water. Therefore, the Korean government provided additional governmental funds such as the grant of drought disaster. In this study, we tried to calculate the cost of water for drought response based on the cost of tap water for the regional local governments in Korea and the grant of drought disaster by the Ministry of the Interior and Safety in Korea, etc. The estimated costs of water for drought responses in coastal and inland areas which have a chance to apply alternative water sources such as brackish or seawater desalination and water reuse in Korea were higher than in other areas in Korea. Additionally, as the novel approach of drought response, the 300 m3/day-scale desalination vessel was suggested to provide desalinated water for the islands in Korea. The estimated expenses of water supply for the target island areas (Sinan-gun and Jindo-gun) by the desalination vessel was lower than those by emergency water service by using bottled water.

Maritime transportation plays a significant role in global economies. Seaports as primal nodes in maritime supply chain are also indispensable in ensuring efficient and effective global trading. On the other hand, seaport inefficiencies have profound influences on the overall performance which can cause congestion, operational disruption, high cost expenses, unnecessary wastes and environmental pollution, which eventually resulting significant financial losses. As a result, business and environmental sustainability will not be achieved. In order to overcome these hindrances, a novel performance model of Lean, Agile, Resilience and Green (LARG) is proposed as management tools for enhancing the business and environmental sustainability in seaport supply chain operations. The compatibility of LARG paradigms in seaport supply chain need to be identified and analysed to achieve the research aim. This paper employed a compatibility analysis for the new LARG paradigm for enhancing seaport supply chain practices. In this analysis, all potential paradigms are thoroughly reviewed and further validated by the domain experts consisting of academic and industry experts. The result of this paper shows that 17 selected LARG paradigms are compatible with 23 seaport supply chain practices respectively. For future research, the identified paradigms can be further investigated for many purposes such as measuring their influence on seaport supply chain practices and even assessing their applicability. It is worth mentioning that this research outcomes can assist Malaysian seaport practitioners to develop an enhanced management paradigm to boost their performance based on LARG model. Moreover, this model also can be applied globally as it is able to be adapted, revised and adjusted to suit the seaport preferences. As a result, this model able to enhance business capabilities, operational efficiencies and competitive advantages of seaport supply chain operations globally.

Currently many companies are interested in reduction of the carbon emissions associated with their supply chain activities such as transportation and operations. Operational decisions, such as modifications in order quantities could an effective way in reducing carbon emissions in the supply chain. Cap-and-trade regulation, sometimes called emissions trading, is a market-based tool to limit greenhouse gas emissions. Under cap-and-trade regulation, emission credits are allocated to the firms and the firms trades emissions under cap-and-trade schemes. In this paper, we propose a single-manufacturer single-buyer two-echelon supply chain problem under the cap-and-trade mechanism incorporating the carbon emissions caused by transportation and warehousing activities where a single manufacturer produces a family of items in order to deliver a family of items to a single buyer at a fixed interval of time for effective implementation of Just-In-Time (JIT) Purchasing. An integrated multi-product lot-splitting model of facilitating multiple shipments in small lots between buyer and manufacturer is developed in a JIT Purchasing environment. Also, an iterative heuristic algorithm is developed to derive the common order interval, the number of intervals for each product and the number of shipments between the buyer and the manufacturer during the common interval. A numerical example is given to illustrate the savings in reduction of total cost and carbon emissions by the inventory model incorporating cap-and-trade mechanism compared to the classical inventory model. The proposed inventory model could be useful for the practical solution of two-echelon supply chain inventory problem under cap-and-trade mechanism.

Pipe for water supply is one of the important parts that supply water to home, factory and so on. Water leakage in pipe for water supply due to deterioration, ground sinking and earthquake leads to enormous economical loss. Therefore, pipe for water supply should be designed to satisfy the requirement of, for instance, structural stability and fatigue durability. The purpose of this study was to investigate the fatigue durability of flexible joint for relaxing the impact due to earthquake and ground sinking. For this purpose, flexible joint was simulated using dynamic characteristics and fatigue life. As the results, the problem of fatigue durability may occur when flexible joint and pipe for water supply are treated as rigid body in simulation. Thus it means that the role of packing in flexible joint is very important and packing should be designed as optimal conditions that are considered fatigue durability as well as waterproof.

The results of internal temperature. productivity and immunity analysis of the laying hen house by the thermal environment and the supply of cold drinking water were as follows. The external temperature was changed from the minimum of 18℃ at night and the maximum of 36℃ during the day, and the internal temperature of the laying hens varied from 20~31℃. Thermal imaging analysis showed that the body temperature of the laying hen decreased by 2.4℃ with the supply of drinking water. The laying hen amount increased 2.36g and laying hen rate increased 3.62%p. Albumin increased 6.1%, decreased AST 15%, and decreased cholesterol 12.7%. Immune activators increased and T cells and B cells increased to increase immunity.

The pipe for water supply is essential part among SOC (Social Overhead Capital) fields. Pipe for water supply is mainly damaged by deterioration of pipe, earthquake, ground sinking and so on. The leakage of water have been led to enormous economical loss in our country. The purpose of this study was to investigate the structural stability of flexible joint for relaxing impact due to earthquake and ground sinking. For this purpose, flexible joint was simulated using tensile load and internal pressure. As the results, flexible joint for structural stability was needed the tensile load of below 3 ton and internal pressure of below 60 kgf/cm2. However, it is considered that real flexible joint should be applied more high safety factor than that of simulation result because of combined stress.

The present study identified several antecedents that create perceived resistance to supply chain management (SCM) change. This work particularly emphasizes SCM change, which is notable given its central role in reacting market orientation and varied environmental and managerial conditions. A careful case study on a small and medium sized food production company in South Korea leads to the formulation of our framework including one second-order construct of ‘resistance’ as well as eight first-order constructs of ‘implementing the payment terms’, ‘balancing of business process’, ‘fear of responsibility’, ‘business sustainability transparency’, ‘past experience of failure’, ‘competence of work personnel’, ‘cooperation with third parties’ and ‘sharing personnel information with partner’. The hypothesized relation of first- and second-order construct was validated using survey sample data collected from 350 respondents who completed their questionnaire instrument. Results from confirmatory factor analysis revealed that nomological validity was established at statistical significance level by identifying six first order constructs of ‘implementing the payment terms’, ‘fear of responsibility’, ‘business sustainability transparency’, ‘past experience of failure’, a conbined construct of 'competence of work personnel/ cooperation with third parties’ and ‘sharing personnel information with partner’. The findings from our work are expected to provide important insights to the strategy for SCM risk management for small and medium sized company.

Fair Allocation of profits or costs arising from joint participation by multiple individuals or entities with different purposes is essential for their continuing involvement and for their dissatisfaction reduction. In this research, fair allocation of the profits of forming a grand coalition in Three-Echelon Supply Chain (TESC) game that is composed of manufacturer, distributor and retailer, is studied. In particular, the solutions of the proportional method of profit, the proportional method of marginal profit, and Shapley value based on cooperative game theory are proved to be in the desirable characteristics of the core. The proportional method of profit and the proportional method of marginal profit are often used because of their ease of application. These methods distribute total profit in proportion to profits or marginal profits of each game participant. In addition, Shapley value can be defined as the average marginal profit when one game player is added at a time. Even though the calculation of the average of all possible marginal profits is not simple, Shapley value are often used as a useful method. Experiments have shown that the solution of the incremental method, which calculates the marginal cost of adding game players in the order of manufacturers, distributors and retailers, does not exist in the core.

This study would present a risk analysis method to evaluate stable tap water supply in a multi-regional water supply system and propose a measure for the evaluation of the effect of the conjunctive operation of the multi-regional water supply system using this. Judging from the vulnerability for the crisis response of the entire N. multi-regional water supply system, as compared to the result of Scenario 1 in which no conjunctive pipes were operated, it was found that in Scenario 2, in which conjunctive pipes were partially operated, the vulnerability of crisis response decreased by about 30.6%, and as compared to Scenario 3, the vulnerability of crisis response decreased by 86.2%. In setting a plan for stable tap water supply in N multi-regional water supply system, using the estimated value and the method for the evaluation of the vulnerability of crisis response by pipe, by interval and by line, it is judged that this can be utilized as a basis for the judgment of the evaluation of the operation or the additional installation of conjunctive pipes.