Powder characteristics, such as density, size, shape, thermal properties, and surface area, are of significant importance in the powder bed fusion (PBF) process. The powder required is exclusive for an efficient PBF process. In this study, the particle size distribution suitable for the powder bed fusion process was derived by modeling the PBF product using simulation software (GeoDict). The modeling was carried out by layering sintered powder with a large particle size distribution, with 50 μm being the largest particle size. The results of the simulation showed that the porosity decreased when the mean particle size of the powder was reduced or the standard deviation increased. The particle size distribution of prepared titanium powder by the atomization process was also studied. This study is expected to offer direction for studies related to powder production for additive manufacturing.

강원지역은 우리나라의 다설지로서 복잡한 지형 때문에 강설량의 공간변동성이 크다. 특히 동풍조건에서 강설이 발생할 시 강설량의 공간적 변동을 예측하기 어렵다. 동풍조건에서는 강원지역 내 위치에 따라 대기환경조건이 다르며 이는 강설의 특성에도 영향을 줄 수 있다. 본 연구에서는 동풍 조건에서 태백산맥의 풍상측과 풍하측에서 강설의 미세 물리적 특성을 서로 비교 분석하였다. 강원지역 내 4개 관측지점을 선정하여 파시벨 수적계로 입자크기분포를 관측하였다. 얻어진 강설입자 크기 분포의 특성을 풍상측과 풍하측간 비교한 결과, 풍상측의 강설입자 크기 분포는 풍하측에 비해 넓은 분포를 가졌고 작은 강설입자의 수도 많았다. 강설입자의 수농도에 비례하는 보편특성수농도와 강설입자의 직경에 비례하는 보편특성직경 둘 다 풍상측에서 상대적으로 큰 값을 보였다. 또한, 얼음수함량과 강설강도 비교에서도 풍상측 지점에서 큰 평균값을 가졌다. 이 결과가 나타난 원인은 태백산맥 산사면에서 공기덩어리의 강제적 상승효과로 풍상측 지점 상공에 새로운 강설입자의 생성이 활발했기 때문으로 추정된다. 또한, 풍상측은 따뜻하고 습한 동풍이 불어오므로 이로 인해 지상기온이 0oC 근처에 머무르며 강한 부착과정이 일어나기 좋은 조건이다.

This study aims to analyze the effects of 4 directions of wind, wind speed, year of construction of slate roofs, installation area and other factors on the concentration and size distribution of airborne fiber particles in farmhouses with a slate roof containing asbestos. Airborne fiber particle samples were collected from the air in six houses with a slate roof containing asbestos using a high flow rate pump (10 L/min) for 2 hours, three times a day with a different condition, 72 times in total. The airborne fiber particle concentrations were measured using a phase contrast microscope, and the size of fiber particles of 72 samples in total was estimated using the mean value of those in each sample measured at 100 with a field of view. The total average concentration of fiber particles collected from in the air in four directions of the targeted farmhouses was 2.83 fiber/L, and its maximum concentration was 5.75 fiber/L, which means that among all samples there was no place that exceeded 10 fiber/L, a recommended indoor air quality standard. The average size of the fiber particles was 11.55 μm, and the maximum size was 40 μm. A multiple regression analysis of factors affecting the concentration and size of fiber particles in the air collected from the farmhouses with a slate roof containing asbestos found that the closer to the main wind direction (p<0.001) and the faster the average wind speed (p<0.05), the fiber particles concentration became significantly higher. In this case, the coefficient of determination was 52.8%. It was also found that the wider the total area of the slate roof (p<0.001) and the slower the average wind speed (p<0.05), the longer the fiber particles; the coefficient of determination for this finding was 19.6%. The concentration of fiber particles in the air of farmhouses with a slate roof appeared to be the highest under the main wind direction, and became significantly higher as the wind speed became faster. This proved that fiber particles were leaked from the slate roof. The size of the fiber particles became significantly longer as the area of the slate roof became wider and the wind speed became slower.

Recycled cenosphere, which is a hollow shaped particle from fly ash, has become attractive as a building material due to its light weight and excellent heat insulation and soundproof properties. In this paper, we investigated the effect of cenosphere size on the physical and optical properties. High brightness of cenosphere as raw material is required for a wide range of ceramics applications, particularly in fields of building materials and industrial ceramic tiles. Cenospheres were sorted by particle size; the microstructure was analyzed according to the cenosphere size distribution. Cenospheres were generally composed of quartz, mullite, and amorphous phase. Colour measurement corresponding to chemical composition revealed that the contents of iron oxide and carbon in the cenospheres were the major factors determining the brightness of the cenospheres.

The purpose of this study is to validate and verify a head nose exposure inhalation system for nano particle inhalation toxicity studies. Carbon nano tube(CNT) particles were generated by a chemical vapor deposition(CVD) generator. And purchased single wall carbon nanotubes(SWCNT) and multi wall carbon nanotubes(MWCNT) were generated by an atomizer. CNT particle distribution was measured by Scanning Nano-Particle Spectrometer(SNPS) and Condensation Particle Counter(CPC). Diameter and length of MWCNT generated by CVD were 10~40 nm and 220~20 μm respectively. Particle number concentration of MWCNT generated by CVD were 1.3×105, 4.1×104, 5.6×103#/cc in high, middle, low chamber respectively. Distribution of particles which were less than 100 nm was 45%. Particle number concentration of SWCNT generated by atomizer after magnetic stirring were 8.5×106, 5.3×105, 1.1×104#/cc and after sonication 6.7×106, 4.1×105, 9.5×103#/cc in high, middle, low chambers respectively. Particle number concentration of SWCNT generated by atomizer after magnetic stirring were 6.7×106, 4.6×105, 8.6×103#/cc and after sonication 7.7×106, 5.1×105, 1.3×104#/cc in high, middle, low chambers respectively. We set up head nose exposure inhalation system to conduct a study on nano particle inhalation toxicity. There were sufficient particle number concentrations of nano particles generated in each chamber.

In this paper we have studied the effect of water droplet size on nano-particle size distribution using SMPS(Scanning Mobility Particle Sizer)system. It can be seen that the unknown peak at >100 nm was caused by water droplets which did not dry completely when DI water was used as a solvent in the SMPS system. Therefore, it is important to dry water droplets generated from atomizer in the SMPS system when measuring the particle size distribution using less than 100 nm nano-particles in diameter. From this study, It can be concluded that the napion was a useful material as dryer ones and using EAG(Electro Aerosol Generator) as a particle generator was the most effective in reducing the effect of water droplets.

The effect of particle size distribution on green and sintered properties of Fe-Cr-Mo prealloy powder was investigated in this study. For the study, prealloyed Fe-Cr-Mo powders with different particle sizes were mixed as various ratios and cold compacted at various pressure and sintered at for 30 min, atmosphere in the continuous sintering furnace. The results shows that the powders with large particle size distribution have high compressibility and low ejection force. However the green strength are much less than those with small particle size distribution. Tensile prperties of the sintered specimes with large particles size also have high strength and elongation.

최근 들어 온난화 등의 영향으로 태풍이나 집중호우가 빈번히 발생하고 있으며 이로 인한 산지 도로의 산사태, 토석류, 상향침투수압 등에 의한 인명, 시설물 피해도 극심하게 나타나고 있다. 산지 도로의 상향침투수압은 심각한 포장 파손을 발생시키기도 한다. 산지 측의 높은 지하수위로 인한 상향침투수압을 감소시키기 위해서는 지하배수공법이 매우 효과적 이라고 판단된다. 지하배수 공법을 원활하게 작동하기 위해서는 배수기층이 적합한 투수계수와 지지력을 갖추어야 한다. 따라서 본 연구에서는 적절한 투수성과 지반 지지력을 확보할 수 있는 최적의 배수기층 입도에 대한 연구를 수행하였다.

습식분쇄의 최적조건을 얻고자 부형제 종류, 농도, 습식분쇄시 rotor speed, bead size, feed rate, 분쇄회수를 달리하여 분쇄한 결과, 부형제로는 gum arabic을 사용하여 5%의 농도로 첨가할 때 가장 좋은 분쇄효과를 나타내었다. Rotor speed를 달리하여 습식분쇄한 결과, rotor speed가 증가할수록 좋은 결과를 나타내어 4,000 rpm에서 가장 우수한 것으로 나타났다. 원료와 직접 부딪혀 분쇄를 하게 되는 bead는 0.4 mm의 크기를 사용하였을 때 가장 작은 사이즈로 분쇄되는 것으로 나타났다. 분쇄가 이루어지는 chamber내에 원료를 공급하는 비율에 따른 결과에서는 40 L/h 의 속도로 공급했을 때 가장 작은 입도분포를 보였다. 분쇄회수에 따른 영향은 횟수에 따라서는 8회 이상으로 분쇄하였을때 0.6 μm이하의 입도분포가 90% 이상으로 나타나 10회를 분쇄하였을때 가장 좋은 효과를 나타내었다. 연속운전과 비연속운전의 비교에서는 연속운전이 더 효율적이었으며 부형제 종류에 따른 영향은 gum arabic을 첨가하여 분쇄하였을때 가장 우수한 결과를 나타내었다. 따라서 적절한 농도와 종류의 부형제 사용과 rotor speed, bead size, feed rate, 용매와의 혼합비의 최적공정을 수립한 습식분쇄기술로 초미세액상칼슘의 제조가 가능하였고, 습식분쇄기술을 식품가공기술로 활용할 수 있는 가능성을 확보하였다.

본 연구는 고속도로 강우 유출수에서 입도 크기 분포 특성(PSD)을 이해하기 위하여 수행하였다. 경기도내 4곳의 포장도로 지역에서 2번의 강우사상동안 강우유출수 샘플 모니터링을 수행하였고, 시료내 입자의 크기분포를 분석하였다. 또한, 강우량, 유량 및 각 오염물질들을 분석하였다. 시료내 입자의 시간별 변화농도는 강우유출수의 시작 시 높은 값을 보였다가 급속히 감소하였으며 탁도, 총부유물질, BOD, 총질소 및 총인과 같은 오염물질과 유사한 유출경향을 보여주었다. 특히 총부유물질과 탁도와의 높은 상관성을 보여주었다. 강우유출수와 퇴적물내에 포함된 중금속에 있어서 구리, 납, 아연은 높은 농도를 보였으며 대부분의 중금속은 넓이에 대한 부피의 비율이 큰 세립입자에 강하게 결합된 형태로 존재한다.

토마토 펄라이트 자루재배법의 확립을 위한 기초 연구로, 입도분포가 다른 7가지 충진용 펄라이트를 대상으로 물리성 및 수분특성을 조사했다. S-1(1.2-5mm), S-2(0.15-5mm) 및 S-5(Parat No. 1)에서는 1.0-2.8mm의 입자 및 2.8mm 이상의 입자가 비교적 고르게 분포하였다. (1-3mm), S-4(Parat No. 2), S-6(OTAVI) 및 S-7(Agroperl B-3)에서는 1.0-2.8mm의 입자가 84.66, 58.67, 32.11 및 41.75%이었고, 2.8mm 이상의 입자가 8.85, 8.84, 15.73 및 22.26%로 비교적 대립이 적게 분포하였다. 특히, S-4, S-6 및 S-7은 1mm 이하의 입자가 많이 분포하였다. 공극률은 59~62% 정도로 제품간 큰 차이를 보이지 않았다. 용기용수량은 S-2에서 27.7%로 낮은 것을 제외하고는 35~40% 사이의 수치를 나타내었다. 모든 배지는 수분장력 0kPa에서는 약 60%정도의 수분을 보유하였으나 4.90kPa에서 급격히 감소하여, 식물이 쉽게 흡수할 수 있는 수분 량이 많았다. 물리적 특성을 조사한 7가지 배지 중에서 입도분포가 다른 3가지 배지 S-1, S-2 및 S-3에 대하여 자루재배 적응성을 평가하였다. 공시 토마토는 로꾸산마루(사카타종묘)이었다. 자루 규격은 길이 120×폭 34cm(배지량 40리터, 흑백PE비닐 두께 0.1mm)였다. 생육일수에 따라 일사량과 급액량 및 배액율을 조사한 결과, 배지간에 일정한 경향을 발견하기 어려웠으며, 처리간에 급액 및 배액의 차이는 인정되지 않았다. 배지 종류별 자루단면의 뿌리분포를 나타낸 결과, S-1과 S-2에서 S-3에 비해 뿌리 분포량이 많은 것으로 나타났다. 모든 처리에서 생육은 비슷하였다. 수량은 S-1 처리가 다른 처리에 비해 총수량이 8,628kg/10a로 다소 높았다. 과실 당도는 처리간 차이가 없이 4.9~5.1˚Brix 수준이었으며, 소형과와 기형과는 S-3에서 많이 나왔다. 이상 연구결과에서 입도분포가 1.2-5mm인 것이 바람직한 것으로 나타났다.

The effect of the preparation factors, such as the feeding mode and rate of raw materials, the reaction temperature and the surfactant on the size distribution of molybdenum trioxide particle were investigated by orthogonal test. The optimum conditions for the preparation of precursors are as following; opposite feeding fast, reaction temperature of and adding dispersant.

The W/O emulsion was formed by mixing hydrophobic nonion surfactants of span 80 and tween 60 with kerosine, and by adding sodium silicate aqueous solution. Precipitating the W/O emulsion by sodium bicarbonate resulted in spherical silica particles. Shape and size distribution of silica particles were observed. The particles were spherical and they have narrow size distribution. Particle sizes were 9.29, 7.39 and 5.73 μm at homogenizer speed of 2500, 3000, and 3500 rpm, respectively. The particle size was decreased by increasing agitation speed due to the formation of emulsion droplet. At fixed agitation speed, absorbed paraffin oil weight were measured and the SiO2/Na2O mole ratio effects on particle size were investigated. Particle size was decreased by increasing the mole ratio of SiO2/Na2O.

The study was conducted to evaluate the penetration performance of Surface Protection Material(SPM) according to the particle size distribution of fine aggregate. The fine three types of aggregates were used, and the amounts of SPM were applied 0.13, 0.25, 0.36, and 0.51 kg/㎡. Test results indicated that the penetration depth of SPM were improved with increasing the amounts of application of SPM. And The penetration depth of SPM were improved with increasing the percentage of passing weight of size of sieve between 0 and 1.25mm.

As an interpretation of existing jamming effects, the main variables affecting the increase in stiffness due to jamming are known as system density, jamming density, pressure, and particulate temperature. The main variable, jamming density, is closely related to the distribution of particle size and contact properties such as particle shape and friction. However, the complexity of these variables makes it difficult to fully understand the mechanism of the jamming effect. In this paper, we focus on the jamming effects of particles that have more elastic properties than particles such as sand and coffee powder, which are commonly used as constituent particles of existing jamming, in order to reduce complicated factors such as temperature and concentrate on jamming effects based on elastic characteristics of particles. It was experimentally explored the possibility of increasing stiffness by mixing particles of different sizes rather than simply increasing the bending stiffness by controlling the particle size. Through simulations and experiments, we found a case where the stiffness of each particle size distribution is larger than the stiffness of each particle size.

In order to ensure the high carbon conversion in a short residence time in a coal slurry entrained gasifier, the objectiveof this study lies in to investigate the effect of important variables to influence on the complex reacting flow and therebyto clarify the physical feature occurring inside the gasifier using a comprehensive gasifier computer program. To this end,the gasification process of a 1.0ton/day gasifier is numerically modeled using the code of Fluent and systematicallyinvestigated with the change of major design and operation parameters. Special emphasis is given on the effect of theparticle size distribution on the gasification process, since it is associated with various length and time scales via multi-phase and with complex reacting flows. Three different particle sizes are tested for a given coal mass flow rate, the firstis 70µm mean diameter with Rosin-Rammler distribution based on the actual measurement. But in the other two casestwo uniform mean particle diameters are employed, that is, very fine 1µm and 70µm with mean diameter itself. Thecalculation results of these three cases show quite different flow pattern, temperature and reacting flows probably causedby the different particle trajectory as well as reaction rate. However, the results obtained can be explained in a consistentmanner with particle size. Especially, it is noted that the presence of coal particle, the diameter of which is larger thanthat of mean diameter of Rosin-Rammler distribution, shows a significantly retarded gasification reaction in a gasifier,even if its mass fraction is less than 50%.

본 연구에서는 파쇄 메커니즘이 상이한 파쇄기(함마 크럿셔와 롤 크럿셔)와 파쇄회로(개회로 및 폐회로)를 사용하여 각각의 파쇄기 종류에 따른 백운석 파쇄산물의 입도분포와 파쇄특성에 대해 알아보았다. 함마 크럿셔로 파쇄한 경우, 100 mesh 이하의 미분이 약 34 wt.%로 롤 크럿셔로 파쇄한 경우보다 약 3 배 이상 높았다. 또한 14~25 mesh 산물은 롤 크럿셔로 파쇄할 경우, 함마 크럿셔로 파쇄한 경우에 비하여 약 20 wt.% 이상 많이 생성되었다. 35 mesh 이하의 산물은 함마 크럿셔로 파쇄 시 전체의 약 80 wt.% 정도였다. 두 파쇄기 모두 개회로에 비해 폐회로 파쇄 시 미분의 발생률이 감소하였다. 광석에 따른 적절한 파쇄기 및 파쇄회로의 선택에 따라 목적하는 입도의 산물을 효율적으로 얻을 수 있다.