To investigate earthquake responses of structures with basements affected by soil deposits, centrifuge tests were performed using an in-flight earthquake simulator. The test specimen was composed of a single-degree-of-freedom structure model, a basement and sub-soil deposits in a centrifuge container. The test parameters were the dynamic period of the structure model, boundary conditions of the basement, existence of soil deposits, centrifugal acceleration level, and type and level of input earthquake accelerations. When soil deposits did not exist, the earthquake responses of the structures with fixed basement were significantly greater than those of the structure without basement. Also, the earthquake responses of the structures with the fixed basement surrounded by soil deposits were amplified, but the amplifications were smaller than those of the structures without basement. The earthquake responses of the structures with the half-embedded basement in the soil deposits were greater than those estimated by the fixed base model using the measured free-field ground motion. The test showed that the basement and the soil deposit should be simultaneously considered in the numerical analysis model, and the stiffness of the half-embedded was not effective.
Facilitated olefin transport membrane, containing positively charged silver nanoparticles (AgNPs) as olefin carriers dispersed in poly(vinyl pyrrolidone) (PVP), leads extremely high separation performances for propylene/propane mixtures. In this study, as representatives of electron withdrawing nitrobenzene compounds, 1,2-dinitrobenzene (DNB) and 3,4-dinitro toluene (DNT) were used for PVP/AgNPs membranes. The correlation between the surface charge density of AgNPs and the separation performance was investigated with X-ray photoelectron spectroscopy (XPS). A fairly good linear correlation between the surface charge density and the separation performance was confirmed, which meant that the positive charge density on the surface of AgNPs may be a key factor in determining the separation performance of facilitated olefin transport membranes.
CO2 capture technologies have been highlighted over the past decades because of global warming. Among the various technologies for CO2 capture, facilitated CO2 transport membranes show high CO2 selective performance by introducing carrier which interacts with CO2. In this presentation, we prepared and investigated facilitated CO2 transport membrane comprising potassium bis[(trifluoromethyl)sulfonylimide] (TF2N) dissolved in a polymer matrix of Pebax1657. Adding potassium salt to the membrane shows further improvement in gas permeabilities while maintaining or even improving the gas selectivity, compared to the corresponding neat polymer membrane. Therefore, we have demonstrated that KTF2N can act as dual carrier for CO2 and its facilitated transport membrane could be very effective in enhancing the CO2 separation performance.
산업화를 위한 지구자 및 12가지 식물성 원료 추출물의 생리학적 효과를 평가하기 위하여, 만성 에탄 올을 투여한 마우스 혈청 내에서의 생리학적 지표 및 간과 뇌 조직 내에서의 산화적 스트레스에 대한 보호효과를 확인하였다. 에탄올을 투여한 마우스의 혈당은 정상 대조군 그룹(NG)과 에탄올 투여 그룹 (EG)에서 각각 119.43mg/dL, 305.25mg/dL로 나타났고, 에탄올과 혼합 추출물을 동시에 투여한 그룹 (100, 200mg/kg body weight + 25% ethanol 5g/kg body weight, ME100, ME200)에서 각각 272.76mg/dL, 234.60mg/dL로 감소하였다. 혈중 에탄올 함량은 EG에서 4.08mg/dL를 나타내었고 ME100, 200에서 각각 3.85mg/dL, 3.08mg/dL로 감소하였으며, 혈중 아세트알데하이드 함량은 18.72mg/dL에서 각각 15.76mg/dL, 15.16mg/dL로 감소하였다. 또한 ME100, ME200은 혈청 내의 생 리학적 지표에서 간 독성 지표인 glutamine pyruvic transaminase(GPT), glutamic oxaloacetic transaminase(GOT)와 신장 독성 지표인 blood urea nitrogen(BUN), creatine(CRE), 혈중 total cholesterol(TCHO), triglyceride(TG)의 함량이 유의하게 감소하였다. 뇌 조직에서 에탄올에 의해 acetylcholinesterase(AChE)가 EG(116.10%)에서 NG(100.00%)와 비교하였을 때 증가된 활성을 나타냈 으나, ME에서 각각 109.00%와 108.47%로 유의적으로 감소하였다. ME에서 EG에 비해 간과 뇌 조직에 서 superoxide dismutase(SOD)의 함량이 증가하였고, oxidized glutathione(GSH)/total GSH 비율과 malondialdehyde(MDA)의 함량이 감소하였다. 이러한 결과들을 통해 지구자를 포함한 혼합 추출물은 간, 뇌 조직 및 혈액 등에서 만성 에탄올 섭취에 의해 유발된 산화적 스트레스를 효과적으로 보호할 수 있는 제품으로의 개발이 가능할 것으로 판단된다.
생물다양성은 어떤 지역에서 나타나는 종 다양성과 종 풍부성으로 대변할 수 있다(Lande, 1996). 이러한 종 다양 성과 종 풍부성을 판단하는 기준으로 종의 존재와 분포에 대한 데이터는 생물다양성의 보전을 위해 계획하고 평가하 는데 중요한 요인으로 작용한다. 백두대간은 한반도 핵심 생태축으로 멸종위기 야생생물을 포함한 다양한 동·식물 1,300여종 이상이 서식하고 있는 생태계의 보고로 알려져 있다. 그러나 도로 및 개발 등의 훼손행위에 의해 백두대간 을 비롯한 산림생태계가 단절되는 구간이 점차적으로 늘어 나고 있다. 더불어 국내 등산인구는 연간 1,800만명으로, 등산을 통해 삶의 활력과 건전한 여가생활을 즐기는 사람들 이 증가하고 있다. 이런 요인들은 야생동물과 인간이 산림 내 활동하는 중첩 공간과 마찰되는 공간을 증가시켜 야생동 물의 활동범위와 서식공간을 줄어들게 한다. 본 연구는 백두대간 보호지역(육십령∼덕치) 52.5㎞ 구 간을 대상으로 2015년 5월부터 12월까지 주요 능선부에 카 메라 트래핑(Camera trapping, CT)을 통해 백두대간에 서 식하는 육상 포유류와 조류의 모니터링과 등산객의 출현빈 도를 관찰하여 백두대간 핵심지역에서 등산객의 간섭이 야 생동물 출현현황에 미치는 영향을 분석하고자 하였다. 조사 기간 동안 카메라 트래핑을 통해 총 75,613컷의 사진이 촬 영되었으며, 포유류, 조류, 인간으로 구분된 유효사진 4,679 컷을 추출(포유류 992컷, 조류 439컷, 등산객 3,248컷)하였 다. 사진자료 분석시 인간을 제외한 포유류, 조류는 5분 이 내에 동일한 종이 2회 이상 촬영된 것은 중복으로 고려하여 단일 컷으로 간주하였다. 또한 사진 확인 결과 화각 범위 내에서 빠른 이동으로 인한 흔들림이나 일부 몸체 부위만 촬영되어 동정이 불가능한 사진은 분석에서 제외하였다. 카메라 트래핑을 통해 촬영된 포유류는 5목 9과 14종이 확인되었으며, 가장 높은 출현빈도를 보인 종은 고라니가 208컷(21.0%)을 차지하였다. 청설모와 다람쥐는 주간에만 출현하였으며, 나머지 12종은 주로 야간시간대에 출현빈도 가 높은 것으로 확인되었다. 조류는 16종으로 팔색조, 진홍 가슴, 들꿩 등 관찰이 용이하지 않은 멸종위기 야생생물 또 는 관찰빈도가 낮은 종과 회피성이 강한 종이 확인되었다. 특히 멸종위기 야생동물(Ⅱ급)인 팔색조의 확인은 앞으로 조류 조사방법으로 카메라 트래핑의 활용가능성과 필요성 을 시사한다. 등산객의 출현은 전체 4,679컷 중 3,248컷 (69.4%)을 차지하였으며, 센서의 오작동이나 등산객의 그 룹산행, 1회 촬영 후 딜레이 타임을 고려하였을 경우 백두대 간을 등산하는 등산객의 수는 이보다 더 많을 것으로 판단 된다. 주간(07시-18시)과 야간(18시-익일07시)산행으로 구 분하면 주간 2,874컷(88.5%), 야간 374컷(11.5%)으로 확인 되었다. 특히 헤드랜턴을 착용한 야간산행은 빛에 민감한 야행성 포유류에 매우 부정적인 영향이 미칠 것으로 판단되 어 관리방안이 필요하다. 향후 연구는 백두대간 동일지역에서 확보된 카메라 트래 핑 자료를 통해 등산객에 의한 인위적 간섭이 야생동물의 재출현에 어느 정도 영향을 미치는지에 대해 정량분석을 시행할 예정이다.
Modern football has transformed into a scientific football based on data. With this trend, various methods for tactics studies and outcome prediction have been developed on the perspective of data analysis. In this paper, we propose a structural equation model for football game. We analyze critical factors that affect to the winning of game except psychological parts and the causal relationship between latent variables and observed variables is statistically verified through the proposed structural equation model. The results show that the Passing ability and the Ball possession affect to the Attack ability, and consequently it has a positive impact on the winning of game.
Spare part management is very important to products that have large number of parts and long lifecycle such as automobile and aircraft. Supply chain must support immediate procurement for repair. However, it is not easy to handle spare parts efficiently due to huge stock keeping units. Qualified forecasting is the basis for the supply chain to achieve the goal. In this paper, we propose an agent based modeling approach that can deal with various factors simultaneously without mathematical modeling. Simulation results show that the proposed method is reasonable to describe demand generation process, and consequently, to forecast demand of spare parts in long-term perspective.
Selection of efficient supplier is a very important process as risk or uncertainty of a supply chain and its environment are increasing. Previous deterministic DEA and probabilistic DEAs are very limited to handle various types of risk and uncertainty. In this paper, I propose an improved probabilistic DEA which consists of two steps; Monte Carlo simulation and statistical decision making. The simulation results show that the proposed method is proper to distinguish supplier’s performance and provide statistical decision background.
This paper reviews the current seismic design code and research for dynamic earth pressure on retaining structures. Domestic design codes do not clearly define the estimation of dynamic earth pressure and give different comments for seismic coefficient, wall inertia and distribution of dynamic earth pressure using Mononobe-Okabe method. AASHTO has been revised reflecting current research and aims for effective seismic design. Various design codes are analyzed to compare their performance and economic efficiency. The results are used to make improvement of current domestic seismic design code. Further, it is concluded that the experimental investigation is also needed to verify and improve domestic seismic code for dynamic earth pressure.
본 연구에서는 간척지 풍 환경 특성에 따른 온실의 환 기효율 분석 연구에 대한 기초연구로서 단동 양지붕형온실을 대상으로 간척지 풍 환경을 적용한 풍동실험 및 PIV 실험을 수행하여 풍속, 환기방식에 다른 온실 내부 공기유동 분석을 수행하였다. 실질적인 간척지 풍환경 적용을 위하여 ESDU 프로그램을 활용하여 풍속 및 난류 프로파일을 설계하여 풍동실험에 적용하였으며 구현 결과 ESDU 대비 5%의 오차 및 상관계수 0.96이 도출 되었으며 적절한 오차범위라 판단하여 이를 기준으로 실험을 진행하였다. 벡터장, 컨투어장을 통한 분석 결과, 풍상측에서 유입 되는 공기가 온실 하부로 주기류층을 형성하고 온실 상부로는 주풍방향과 반대방향으로 다소 약한 기류를 형성 하는 것으로 측정되었다. 이는 환기 시, 온실 하부영역 이 가장 환기가 원활한 위치이며 후류가 형성되는 상부 영역은 저속의 순환구역으로 온실 내부에 있어 환기에 가장 취약한 위치임을 알 수 있었다. 또한 외부풍속 대비 온실 유입구 유속의 경우 상이하게 나타난 바, 이는 차후 환기량이나 환기효율의 산정에 있어 보다 실질적인 수치가 될 것으로 사료된다. 온실 내부 중앙부 기준 수직 높이에 대한 높이별 유속 수치 도출 및 분석결과, 풍속의 증가율에 비례하여 내부 유속 분포 수치 또한 비례해서 증가하는 것을 알 수 있었다. 환기방식에 따른 내부 유속 저감 비율은 측창 환기, 측창-천창 환기의 경우 각각 약 40%, 30%로 나타났으며 측창-천창 환기조건에서는 천창을 추가적으로 개방 함으로써 공기의 유입되는 면적이 증감함에 따라 온실을 기준으로 발생되는 부압이 감소하여 오히려 측창 환기조 건보다 더 큰 유속 수치가 도출된 것으로 사료된다. 이는 차후 질량교체 환기량, 추적가스 감쇠법 등의 방법을 통한 환기량 산정에 있어 환기방식에 따른 환기량의 변화양상에 대한 분석을 추가적으로 수행할 필요성을 지니는 자료로 판단된다. 본 연구를 통하여 도출된 결과를 바탕으로 전산유체 역학(Computational Fluid Dynamics, CFD) 시뮬레이션에 접목하여 앞서 도출된 정량적인 높이별 유속 수치 및 정성적 유동분포를 기준으로 검증 및 정확도 향상을 통한 환기분석 모델을 설계하고자 하였다. 온실 내부의 공기유동에 따른 보다 실질적인 환기 척도를 도출하여 다양한 온실형태별, 환경조건별, 환기방식별 환기경향 분석 및 예측이 가능할 것으로 전망되며 시뮬레이션을 활용한 온실 체적 전체 및 구역별 환기량을 예측하여 환기 취약 구역을 파악, 보완할 수 있을 것으로 기대된다.
In this study, a series of dynamic centrifuge tests were performed for a soil-foundation-structural interaction system in dry sand with various embedded depths and superstructure conditions. Sinusoidal wave, sweep wave and real earthquake were used as input motion with various input acceleration and frequencies. Based on the results, a natural period and an earthquake load for soil-structure interaction system were evaluated by comparing the free-field and foundation accelerations . The natural period of free field is longer than that of the soil-foundation-structure system. In addition, it is confirmed that the earthquake load for soil-foundation-structure system is smaller than that of free-field in short period region. In contrast, the earthquake load for soil-foundation-structure interaction system is larger than that of free-field in long period region. Therefore, the current seismic design method, applying seismic loading of free-field to foundation, could overly underestimate seismic load and cause unsafe design for long period structures, such as high-rise buildings.
Ultra high performance concrete which has recently been studied was developed to complement the brittle behaviour and dynamic uppermost limit of high strength concrete. Fiber reinforced concrete which mixed steel fiber is receiving attention as an alternative about this and is being developed to complement the disadvantages of high strength concrete including lower toughness coefficients and crack resistance and spalling in fires. Review about fiber reinforced ultra high strength concrete that this study tries to treat includes reduction of self shrinkage generated by high cement content per unit volume of concrete, evaluation of compression and tension strength to lower internal and external spalling resistance and fragility factors of member of framework, and flow characteristics of concrete which doesn't harden according to steel fiber amounts and used materials. As the result, the more fiber reinforcement increases, the more compression and tensile strength increase and deformation control of cement matrix and improvement of energy absorption ability showed the great effect in shrinkage reduction.
Material flow control (MFC) is a kind of operational policy to control of the movement of raw materials, components, and products through the manufacturing lines. It is very important because it varies throughput, line cycle time, and work-in-process (WIP) under the same manufacturing environments. MFC can be largely categorized into three types such as Push, Pull, and Hybrid. In this paper, we set various manufacturing environments to compare five existing MFC mechanisms: Push, Pull, and Hybrid (CONWIP, Gated MaxWIP, Critical WIP Loops, etc). Three manufacturing environments, manufacturing policies (make to stock and make to order), demand (low, medium, high), and line balancing (balanced, unbalanced, and highly unbalanced) are considered. The MFCs are compared in the point of the five functional efficiencies and the proposed compounded efficiency. The simulation results shows that the Push is superior in the functional efficiency and GMWIP is superior in the compounded efficiency.
In this study, expedite curing period at curing temperature being 40, 60, 80℃ similar to strength of standard 28days curing temperature to confirm methods and applicability of early estimation of strength by warm water curing. Also, checked the effect related to different conditions such as using various kinds of material, differentiating quantity of material, with or without fiber mixing at same rate of water-bonding material. Existing method proposed by KS and JIS to estimate strength of 28 days standard curing temperature curing for 7days at 40℃ is not relevant because it takes so long to estimate strength. Already known method of estimating strength of 28days standard curing temperature curing for 3days in 60℃ warm water, too, is not relevant to apply 3day cycle of super high-rise. It also had the problem which didn’t consider fiber mixed concrete. According to the result of experiment, traits and rate of strength revelation were different relating to the kinds and quantity of bonding material. Strength value of mix without fiber was higher than that of mix with fiber, but without any relation to that, over 96% of similar confidence level with strength of 28 days standard curing temperature was shown in 7 days at 40℃, 3 days at 60℃, 2days at 80℃. Confidence level of estimation method of 2 days at 80℃ was similar to those of estimation methods of 4 days at 40℃, 3 days at 60℃, so it(2 days at 80℃) is regarded as the most relevant method because it’s possible to estimate strength fastly. As a result it can be said that early quality control of recently increasing super high-rise may be possible through estimation method of 2 days at 80℃.
제초제 성분인 phosphinothricin을 분해하는 phosphinothricin acetyltransferase (PAT) 단백질을 과발현시킨 제초제저항성 감 자가 개발되었다. 본 연구에서는 안전성평가 기준에 따라, PAT 단백질과 제초제저항성 감자에 대한 급성경구독성 및 아만성 독성 평가를 실시하였다.
PAT 단백질을 재조합 대장균에서 분리정제 한 후, ICR계 쥐에 2,000 mg/kg weight 용량의 PAT 단백질을 먹이고 14일 동안 치사율과 체중증가를 관찰한 결과, 죽은 동물이 없었고, 체중증가, 사료 섭취 및 특별한 이상증상을 발견하지 못했다.
아만성 독성의 경우 제초제저항성 감자를 표준사료에 0, 1, 5% 섞어 90일 동안 경구 투여하였다. 이 경우에서도 사망한 개체는 없었으며, 조사한 여러 항목에 대해 특별한 이상증후를 관찰하지 못했다. 또한, 제초제저항성 감자를 먹인 동물군과 대조구로 일반감자를 먹인 동물 사이에서 유의 할 만한 차이는 발견되지 않았다.
이런 결과를 토대로 볼 때, 제초제저항성 감자와 제초제 저항성 단백질인 PAT는 동물에게 독소로 작용하지 않음을 확인하였다.
This paper has fabricated insulation gang-form adhering general gang-form to the polyisocyanurate board and analyzed type of members, temperature record by locations and strength development after placing the concrete, in order to ensure efficient concrete quality under cold weather. According to our test, we can see that general gang-form member with curing under the same conditions as the actual field has a trend of constantly decreasing concrete temperature regardless to surface or central area due to rapid outdoor air temperature reduction, while in the case of insulation gang-from I and II, temperature increased up to around 25℃ after 12 hours under rapid outdoor air temperature change and temperature distribution did not appear large separation according to hydration reaction measurement locations. In addition, results of measurement for temperature records on weak insulation area by types of gang-forms showed that the temperature record distribution on the form tie surface and horizontal bar surface of angle bar has generally similar trend as the temperature records on the surface of the insulation gang-form, while corner area of the insulation gang-form did not have large insulation effect. It is determined that it requires additional curing measure for the weak corner area of the insulation gang-form in the future.