The pressureless sintering behavior of /Cu powder mixtures, prepared from /CuO and /Cu-nitrate, has been investigated. Microstructural observation revealed that powders with nano-sized Cu particles could be synthesized by hydrogen reduction method. The specimens, pressureless-sintered at for 4 min using infrared heating furnace with the heating rate of /min, showed the relative density of above 90%. Maximum hardness of 16.1 GPa was obtained in /MgO/Cu nanocomposites. The nanocomposites exhibited the enhanced fracture toughness of 4.3-5.7 , compared with monolithic . The mechanical properties were discussed in terms of microstructural characteristics

The aging characteristics of gas atomized Mg-6 wt.% Al-1 wt.% Zn alloy were investigated and compared to those of cast Mg-6 wt.% Al alloy. The gas atomized Mg-6 wt.% Al-1wt.% Zn alloy powders had spherical morphology between 1 and 100 in diameter. After compaction under the pressure of 700 MPa at for 10 min, the Mg-6 wt.% Al-1 wt.% Zn alloy showed a grain size of approximately 40 which is smaller than that of the cast Mg-6 wt.% Al alloy, and a relative compact density of approximately 93%. After ageing, the Mg-6 wt.% Al-1 wt.% Zn alloy showed much faster peak hardness than cast Mg-6 wt.% Al alloy. The Mg-6 wt.% Al-1 wt.% Zn alloy showed the new fine precipitations with ageing time, while the cast Mg-6 wt.% Al alloy was almost similar morphology.

For the purpose of obtaining basic information on the development of lead-free materials, a high density composites (a) W-Cu, (b) W-Sn (c)W-Cu-Sn and (d) W-Cu-Ni were fabricated by the P/M method. The particle size of used metal powders were under 325 mesh, inner size of compaction mould was mm, and compaction pressure was 400 MPa. A High density composite samples were sintered at a temperature between and for 1 hour under Ar atmosphere. The microstructure, phase transformation and physical properties of the sintered samples were investigated. As the results, the highest relative density of 95.86% (10.87 g/) was obtained particularly in the sintered W-Cu-Sn ternary system sample sintered at 450 for 1hr. And, Rockwell hardness (HRB) of 70.0 was obtained in this system.

Disk type porous nickel membrane was fabricated by in-situ reduction/sintering process using compacted NiO/PMMA (PMMA; Polymethyl methacrylate) mixture at 800℃ in hydrogen atmosphere. The porosity (4958%) of these membrane was investigated as an amount of PMMA additive. The thermal decomposition and reduction behavior of NiO/PMMA were analyzed by TG/DTA in hydrogen atmosphere and the activation energy for the hydrogen reduction of NiO and thermal degradation of PMMA was calculated as 61.1 kJ/mol, evaluated by Kissinger method. Finally, the filtering performance and pressure drop were measured by particle counting system.

In this study, we investigated the unit process parameters in spherical kernel preparation. Nearly perfect spherical microspheres were obtained from the 0.6M of U-concentration in the broth solution, and the microstructure of the kernel appeared the good results in the calcining, reducing, and sintering processes. For good sphericity, high density, suitable microstructure, and no-crack final microspheres, the temperature control range in calcination process was , and the microstructure, the pore structure, and the density of kernel could be controlled in this temperature range. Also, the concentration changes of the ageing solution in aging step were not effective factor in the gelation of the liquid droplets, but the temperature change of the ageing solution was very sensitive for the final ADU gel particles

Carbon-coated Cu nanopowders with core/shell structure have been successfully fabricated by pulsed wire evaporation (PWE) method, in which a mixed gas of Ar/ (10 vol.%) was used as an ambient gas. The characterization of the samples was carried out using x-ray diffraction (XRD), scanning electron microscope (SEM), and high resolution transmission electron microscope (HRTEM). It was found that the nanoparticles show a spherical morphology with the size ranging of 10-40 nm and are covered with graphite layers of 2-4 nm. When oxygen-passivated Cu nanopowders were annealed under flowing argon gas (600 and 800), the crystallinity of phase and the particle size gradually increased. On the other hand, carbon-coated Cu nanopowders remained similar to as-prepared case with no additional oxide or carbide phases even after the annealing, indicating that the metal nanoparticles are well protected by the carbon-coating layers.

Niobium(Nb) and Tantalum(Ta) are rarely found apart in nature and never in the free state. The element niobium amounts to 3% of the crustal abundance. On the whole, the niobium capacitor showed somewhat more unstable characteristics than the commercial tantalum capacitors, but is nonetheless considered applicable as a future substitute for tantalum capacitors. In this study, niobium powder was made from potassium heptafluoroniobite(K2NbF7) by using sodium(Na) as a reductant and KCl and KF as diluents based on the hunter sodiothermic reduction method.,In order to obtain a high surface area niobium powder via the sodiothermic reduction method, a certain amount of diluent, such as alkali metal halides selected from NaCl, KCl, KF and NaF, was added in the raw materials to be reduced. However, if a higher surface area of powder is required, more diluents need to be used in the said method in order to produce niobium powder. But when more diluents are used, the niobium powder will be contaminated with more impurities and the yield will also decreased.

Indium Tin Oxide (ITO) thin films on Polyethylene Terephtalate (PET) substrate were prepared by Roll-to-Roll sputter system with targets of 5 wt% and 10 wt% SnO2 at room temperature. The influence of the chromaticity (b*) and transmittance properties of the ITO Films were investigated. The ITO thin films were deposited as a function of the DC power, rolling speed, and Ar/O2 gas flow ratio, and then characterized by spectrophotometer. Their crystallinity and surface resistance were also analyzed by X-ray diffractometer and 4-point probe. As a result, the chromaticity (b*) and transmittance of the ITO films were broadly dependent on the thickness, which was controlled by the rolling speed. When the ITO films were prepared with the DC power of 300 W and the Ar/O2 gas flow ratio of 30/1 sccm using 10 wt% SnO2 target as a function of the rolling speeds 0.01 through 0.10 m/min, its chromaticity (b*) and transmittance were about -4.01 to 11.28 and 75.76 to 86.60%, respectively. In addition, when the ITO films were deposited with the DC power of 400W and the Ar/O2 gas flow ratio of 30/2 sccm used in 5 wt% SnO2 target, its chromaticity (b*) and transmittance were about -2.98 to 14.22 and 74.29 to 88.52%, respectively.

Ti scaffolds with a three-dimensional porous structure were successfully fabricated using powder metallurgy and modified rapid prototyping (RP) process. The fabricated Ti scaffolds showed a highly porous structure with interconnected pores. The porosity and pore size of the scaffolds were in the range of 66~72% and 300~400 μm, respectively. The sintering of the fabricated scaffolds under the vacuum caused the Ti particles to bond to each other. The strength of the scaffolds depended on the layering patterns. The compressive strength of the scaffolds ranged from 15 MPa to 52 MPa according to the scaffolds' architecture. The alkali treatment of the fabricated scaffolds in an aqueous NaOH solution was shown to be effective in improving the bioactivity. The surface of the alkali-treated Ti scaffolds had a nano-sized fibre-like structure. The modified surface showed a good apatite forming ability. The apatite was formed on the surface of the alkali treated Ti scaffolds within 1 day. The thickness of the apatite increased when the soaking time in a simulated body fluid (SBF) solution increased. It is expected that the surface modification of Ti scaffolds by alkali treatment could be effective in forming apatites in vivo and can subsequently enhance bone formation.

In this study, we examined the composition of catechins, theaflavins and alkaloids in leaves during processing to fermented black tea, which is produced by withering, roll breaking, and fermentation of Korean Yabukida tea plant. In addition, we determined the optimal conditions for the production of fermented black tea. The average moisture content in fresh leaves was 70.85%, which dropped to 3.07% in fermented black tea at the last stage of production. When the leaves were analyzed by HPLC, seven types of catechins, four types of theaflavins and three types of alkaloids were identified. The levels of catechins, theaflavins, and alkaloids were then evaluated after being processed into fermented tea. From these experiments, we found that the level of theaflavins, which determines the property of the tea, increased during fermentation. This effect resulted from the change in EGCG, ECG, EGC, EC during the process of fermentation. We also found that the maximal amount of theaflavins was created after 1-2 hours of fermentation. Thus, our results imply that the best condition for producing fermented black tea would be to ferment for 1-2 hours.

The principal objective of this study was to develop and standardize a preparation method for low-sodium tomato jangachi (traditional Korean pickle) via short-term fermentation with immature green cherry tomatoes. In order to determine the preferred concentrations of soy sauce and soaking temperatures of immature cherry tomato pickles in different stages of storage, we conducted an analysis of physico-chemical characteristics and microbiological properties, and also performed a preference test on samples of immature green cherry tomato pickles. Immature cherry tomatoes were prepared in three different soy sauce concentrations --20, 40, and 60%-- and three different soaking temperatures --60, 80, and 100℃-- and then stored for 28 days at 5℃. As a result, the pH increased significantly with increases in the amount of soy in the dipping solution (p〈0.05). The saltiness was maintained at levels of approximately 0.17~0.28% (20% group), 0.32~0.67%% (40%group), 0.48~1.00% (60% group) during storage periods. These results show that the saltiness of immature cherry tomato pickles was substantially lower than that of commercial pickles. The contents of reducing sugar and lightness decreased significantly with increasing concentrations of soy dipping solution. The redness and yellowness values of the tomatoes decreased significantly with increasing concentrations of soy sauce. Additionally, the lower the concentration of soy sauce used, the more rapidly the hardness of the immature cherry tomato pickles was reduced at 100℃. PME activity moved within a narrow range, and then stabilized during the storage period. With regard to the results of the consumer preference test, 20%-100℃ was the most preferred condition overall, 40%-80℃ was the condition in which the texture was most preferred, and 40%-80℃ was the condition that yielded the highest color scores.

Conventional additives were added to a newly synthesized base oil to create synthetic lubricants. Commercial polyol ester prepared in this laboratory were obtained as esterification of 1,1,1-trimethylol propane and respectively. This newly synthesized base oil had a variable chemical structure that could achieved the following properties; oxidation or thermal stability, low temperature fluidity, and higher flash points. When compared with commercial mineral lubricants, the synthetic lubricants show superior thermal and oxidation stability, and anti-wear properties.

Today, wastes of much quantity by fast industrialization and increase in population, population concentration etc. of modem society are increasing. Much oyster shell is breeding by character and conduct of oyster-industry for a long time among them. Oyster shell which breed by-product in oyster cultivating industry that specific gravity of domestic seashore cultivating industry is high is causing environmental problem by problem and so on hindrance, nature spectacle's waste and health hygiene on administration if it is pollution of district along the coast fishing ground, number of public ownership being stored in open area in seashore. About new material just-in-time through recycling and he of oyster shell by these problem wide that study. Go forward more and investigate special quality that is oyster shell's physical chemistry red in this research and oyster shell oyster shell which cause several environmental problems developing ability agricultural chemicals that use this encapsulating micro by ability carrier that is environmentally application possibility examine wish to.

We have produced, characterized and compared different colloidal vehicles based on nanoemulsions. We also have investigated morphology and droplet distribution by means of electron microscope and photon correlation spectroscopy. Nanoemulsion systems characterized by different method on formulations have been obtained. Hydration power has been studied by means of a corneometer, measuring the skin electrical capacitance before and after the application of various type of skin lotions. It has been demonstrated that nanoemulsion with oil or fatty alcohol displayed a pronounced hydration power with respect to the solubilization system. In order to compare the smoothness of the skin after using skin lotion, we have measured the friction force. The skin lotions produced by nanoemulsion technique show improved smoothness of an atopic skin.

세공경 1.5μm인 SPG (Shirasu porous glass) 막이 설치된 실험실 규모의 막유화 장치를 사용하여 구(球) 형상의 단분산 실리카 마이크로겔을 제조하기 위한 막유화 공정변수의 최적조건을 결정하였다. 막유화의 공정변수로는 분산상 내규산소다의 농도, 분산상 압력, 연속상에 대한 분산상의 비율, 연속상 내 유화제의 농도, 연속상의 교반속도로 설정하고, 이들 변수가 제조된 실리카 마이크로겔의 입자 크기와 분포에 미치는 영향을 검토하였다. 막유화의 공정변수들 중에서 연속상에 대한 분산상의 비율, 분산상 압력 및 분산상 내 규산소다의 농도가 증가할수록 겔 입자의 크기가 증가하였다. 반면 유화제의 농도와 연속상의 교반속도가 증가할수록 겔 입자의 크기가 감소하였다. 막유화의 공정변수 조절을 통해 최종적으로 평균 입자 크기가 6 μm인 입도분포가 균일한 구 형상의 실리카 마이크로겔을 제조할 수 있었다.

Poly(vinyl chloride) (PVC) 주사슬과 poly(hydroxyethyl acrylate) (PHEA) 곁사슬로 구성된 빗살모양의 PVC-g-PHEA 공중합체를 원자전달라디칼 중합을 통해 합성하였다. 이렇게 합성된 PVC-g-PHEA의 OH 그룹과 이미다졸 디카르복실릭산 (IDA)의 COOH 그룹과의 에스테르 반응에 의하여 가교된 전해질막을 제조하였다. 인산(PA)을 도핑하여 이미다졸-인산 착체를 형성한 결과, PA함량이 증가함에 따라 고분자 전해질막의 수소 이온 전도도가 증가하였다. 특히 100도 비가습 조건에서 수소 이온 전도도는 최대 0.011 S/cm까지 증가하였다. 만능 재료 시험기(UTM) 측정결과, 제조된 PVC-g-PHEA/IDA/PA 전해질막은 575 MPa의 높은 Young 모듈러스 및 기계적 강도를 보여주었다. 열분석 결과(TGA) 전해질막은 200℃까지 열적으로 안정함을 확인하였다.

H₂S adsorption characteristics of adsorbent made by sewage sludge were investigated. The manufacturing method of adsorbent used in this experiment is to mix sewage sludge, waste lime, the high-alumina cement, NaHCO₃, and activated carbon. For analyses of the manufactured adsorbent, various methods such as scanning electron microscope (SEM), measurements of BET surface area and pore volume were adopted. As operating variables, adsorption temperature (25~45 ℃), H₂S concentration (2.48~31.62 ㎎/L) and the kinds of adsorbent were applied. As major adsorption characteristics, adsorption rate and adsorption equilibrium capacity were measured by using batch type experimental apparatus. The experimental result showed that the BET surface area of the calcinated sewage sludge was 83.3 ㎡/g, which indicates 4 times higher than that of non calcination and the BET surface area of adsorbent made by sewage sludge mixing with various by-products ranged over 265 to 286 ㎡/g. It was also found that the H₂S adsorption equilibrium capacity of adsorbent made by sewage sludge decreases with increasing temperature, but increases with increasing H₂S concentration. Through the evaluation of adsorption isotherm model, it was found that H₂S adsorption isotherm for adsorbent made by sewage sludge can be expressed well by Langmuir and Freundlich isotherm equation.

The goal of this study is to propose the effective method of investigating the injurious factors and making improved plans that prevents the workers against musculoskeletal disorders at an diesel engine manufacturing company and the same business field with similar working conditions and process. A questionnaire were adopted to analyze the symptoms of workers' musculoskeletal disorders, and an ergonomic assessment method such as RULA, OWAS were performed to find out harmful factors of workplace and working posture. Based on the result of the evaluation, to enhance the working environment, improvement of worktable, working space, tools, and outfit was suggested, and induction of mechanical system was also suggested. It can be concluded that the method and process described in this paper could be helpful for diagnosing the musculoskeletal disorders and making improvement plans to the diesel engine fuel injection system manufacturing company and the same business field with similar working conditions and process.

The goal of this study is to propose the effective method of investigating the injurious factors and make improvement plans that prevents the workers against musculoskeletal disorders at plastic product companies and the same business field with similar working conditions and process. A questionnaire are adopted to analyze the symptoms of workers' musculoskeletal disorders, and ergonomic assessment methods such as RULA, OWAS are performed to find out harmful factors of workplace and working posture. Based on the result of the evaluation, to enhance the working environment, improvement of worktable, working space, tools, and outfit was suggested, and induction of mechanical system was also suggested. It can be concluded that the method and process described in this paper could be helpful for diagnosing the musculoskeletal disorders risk factors and making improvement plans to the plastic product companies and the same business field with similar working conditions and process.