This research focused on deciding optimal manufacturing WIP (Work-In-Process) limit for a small production system. Reducing WIP leads to stable capacity, better manufacturing flow and decrease inventory. WIP is the one of the important issue, since it can affect manufacturing area, like productivity and line efficiency and bottlenecks in manufacturing process. Several approaches implemented in this research. First, two strategies applied to decide WIP limit. One is roulette wheel selection and the other one is elite strategy. Second, for each strategy, JIT (Just In Time), CONWIP (Constant WIP), Gated Max WIP System and CWIPL (Critical WIP Loops) system applied to find a best material flow mechanism. Therefore, pull control system is preferred to control production line efficiently. In the production line, the WIP limit has been decided based on mathematical models or expert’s decision. However, due to the complexity of the process or increase of the variables, it is difficult to obtain optimal WIP limit. To obtain an optimal WIP limit, GA applied in each material control system. When evaluating the performance of the result, fitness function is used by reflecting WIP parameter. Elite strategy showed better performance than roulette wheel selection when evaluating fitness value. Elite strategy reach to the optimal WIP limit faster than roulette wheel selection and generation time is short. For this reason, this study proposes a fast and reliable method for determining the WIP level by applying genetic algorithm to pull system based production process. This research showed that this method could be applied to a more complex production system.

다양한 이미지 샘플의 Eye test를 바탕으로 기술적인 화질 지표 조절을 통하여 감성 화질을 최적화 시키는 방법이 소개된다. 여러 가지 이미지 콘텐츠의 다양한 이미지에 대하여, 콘트라스트, 명도, 채도 화질 지표 톤 커브를 사용하여 평가가 수행 되었다. 이미지 화질 향상에 기여하는 우선순위는 명암, 채도 및 밝기 순으로 분석 되었다. 이미지 감성 화질 측정치의 기술적인 화질 지표 변화에 따른 기울기의 공통점을 살펴본 결과, 거의 0, 중간 그리고 최대 기울기의 영역으로 구성된 함수 형태로 모델링을 할 경우, 기존의 역 U 형태의 성질 뿐 아니라 log 또는 포화 형태의 감성 화질 변화까지 분석 가능함을 알 수 있었다. 단일 및 복수의 화질 지표의 경우에 대하여도 화질 개선 방안이 모색 되었으며, 기존 및 본 논문에서 분석된 결과를 위한 새로운 함수가 소개 되었다. 복수의 통합적 이미지 화질 지표를 통하여 향상 시킬 경우 오직 몇몇 한정된 지표 제어의 경우에만 실현 가능하다는 것을 알 수 있었다. 또한, 화질 향상 방법은 영상 콘텐츠에 따라 크게 차이가 없음을 알 수 있었다.

하이테크놀로지를 여러 가지 다른 영역과 융합하고자 하는 노력이 다양한 연구 분야에서 시도되고 있으며, 스포츠웨 어를 개발함에 있어 운동선수의 운동능력을 향상시키기 위한 분야에 이러한 첨단 기술들이 도입되고 있다. 본 연구는 스포츠 훈련에 도움이 되는 동작 센싱 스마트 스포츠웨어를 개발하기 위한 기초 연구로서, 조정 동작 시 관절의 움직임 을 측정할 수 있는 동작 센서를 부착하기 위한 인체상의 최적 위치를 탐색하는 것을 목적으로 한다. 본 연구에서는 일관된 동작을 반복적으로 수행할때 관절의 변화가 큰 조정을 대상 스포츠로 선정하였으며, 조정 선수의 대표 체급인 중량급과 경량급의 피험자를 선정하여 동작에 따른 피부의 변화율을 측정하여 체급별 차이를 분석하였다. 먼저, 3차원 모션캡처 시스템을 이용하여 조정 동작 시 등, 팔꿈치, 엉덩이, 무릎 부위의 피부 변화를 촬영하고, 각 마커 간 거리의 변화율을 분석함으로써 체급에 따른 차이를 보이지 않으면서 동작에 따라 피부의 변화가 큰 부분을 인체 상에 도시하였 다. 이를 바탕으로 동작 센싱용 스마트 스포츠웨어를 위한 센서 부착의 가이드라인을 제시하였다.

Artillery fire power due to effectiveness which is hard to predict well-planned and surprising attack can give a fear and shock to the personnel and is a very core weapon system and takes a critical role in wartime. Therefore in order to maximize operational effectiveness, Army required protecting artillery and takes a quick attack action through rapid construction of artillery’s positions. The artillery use artillery’s position to prevent exposure by moving to other position frequently. They have to move and construct at new artillery’s positions quickly against exposing existed place by foe’s recognition. These positions should be built by not manpower but engineering construction equipment. Because artillery positions have to protect human and artillery equipment well and build quickly. Military engineering battalion have lots of construction equipment which include excavator, loader, dozer, combat multi-purposed excavator, armored combat earthmover dump truck and so on. So they have to decide to optimal number of Team combining these equipments and determine construction sequence of artillery’s position in operational plan. In this research, we propose to decide number of Team efficiently and allocate required construction’s positions for each Team under constraints of limited equipments and time. To do so, we develop efficient heuristic method which can give near optimal solution and be applied to various situation including commander’s intention, artillery position’s priority or grouping etc. This heuristic can support quick and flexible construction plan of artillery positions not only for using various composition’s equipment to organize Teams but also for changing quantity of positions.

As a preparation of a design standard regarding road facilities in terms of reliability based optimum design examples, such as cantilever columns for traffic lights, optimum design in deterministic and probabilistic ways for the foundation of traffic lights poles are proposed. Most of the previous study have focused on the foundation surrounded by cohesionless soil. However, the design would be governed by risky condition. Therefore the resistance by clay-soil is investigated compared with other design specifications. In deterministic optimization, GRG method is applied. It is found that both geometries of deep and shallow foundation provides optimum values. The resistance of cohesive soil is selected to represent the ultimate limit states, in terms of sliding, overturning and bearing pressures from super structures to the foundation under external loads. Example foundations with varying height of columns for traffic lights are optimized about 30% decreased embedded depth of foundation. The optimum coefficients of resistant and load factors may need to be developed with design load combinations in order to prepare design specifications as the next step.

WC-CrC-Ni coatings were prepared by nine processes of the Taguchi program with three levels for the four spray parameters: spray distance, flow rates of hydrogen and oxygen, and powder feed rate. The optimal coating process (OCP) was oxygen flow rate of 38 FMR, hydrogen flow rate of 53 FMR, powder feed rate of 25 g/min, and spray distance of 7 inches. Hardness of 1150 Hv and porosity of 1.2 %, were obtained by OCP; these are better results compared with the highest 1033 Hv and the lowest 1.5% porosity obtained by nine processes of the Taguchi program. Friction coefficient of the WC-CrC-Ni coating decreased from 0.36 ± 0.07 at 25 oC to 0.23 ± 0.07 at 450 oC. These values were smaller than those of the EHC (electrolytic hard chrome) plating at both temperatures due to lubrication from the oxide debris. The wear trace and wear depth of the coating are smaller than those of the EHC at both temperatures. Pitting was not found in the WC-CrC-Ni coating sample, while it did appear in the EHC sample.

This study was carried out to extract ginsenosides in by-products from honeyed red ginseng. Response surface methodology (RSM) was used to optimize the extraction conditions. Based on D-optimal design, independent variables were ethanol (extraction solvent) concentration (30-90%, v/v), extraction temperature (25-70oC), and extraction time (5-11 h). Extraction yield (Y1) and total ginsenosides (Y2) in the extract were analyzed as dependent variables. Results found that extraction yield increased with increasing extraction temperature and time, whereas it was decreased with increasing ethanol concentration. Similar trends were found for the content of ginsenosides in the extracts, except for ethanol concentration, which was increased with increasing ethanol concentration. Regression equations derived from RSM were suggested to coincide well with the results from the experiments. The optimal extraction conditions for extraction yield and total ginsenosides were an extraction temperature of 56.94oC, ethanol concentration of 57.90%, and extraction time of 11 h. Under these conditions, extraction yield and total ginsenoside contents were predicted to be 84.52% and 9.54 mg/g, respectively.

This study investigates the analysis algorithm for developing an optimum hull form with minimum wave resistance by using the practical application of one minus prismatic. In this algorithm the potential-based panel method was adopted to get the wave resistance coefficient as the objective function and SQP method was applied as an optimizer to get the optimum hull form. As an target ship, the series 60(CB=0.6) was taken into account and LBP(length between perpendiculars) of the ship was changed in the direction including a central parallel portion. To verity the validity of this study, the results of the numerical analyses were compared with experimental data.

This study was conducted to optimize the conditions of a sweet rice paste as a replacement of red bean paste recipe using the central composite design of response surface methodology (RSM). Ten experimental recipes with two reference points (rice flour and sugar), were selected, and the physical and sensory characteristics of a sweet rice paste were measured. In the Rapid Visco Analyzer test, breakdown value was the highest in rice flour (105.73 RVU). Sweetness significantly increased with addition of sugar contents (p<0.0002) and viscosity increased with addition of rice flour contents (p<0.0185). Moisture contents decreased with increasing contents of rice flour and sugar, whereas yellowness and redness tend to increase. In the sensory evaluation test, quadratic models for color (p<0.01865), sweetness (p<0.0399), thickness (p<0.0073), and overall acceptability (p<0.0249) were approved as independent for the rice flour and sugar contents. In conclusion, the optimal mixing ratio of sweet rice paste was determined to be 45.38 g of rice flour and 77.95 g of sugar.

본 논문에서는 반응표면법과 다목적최적화 기법을 이용한 유한요소모델개선기법의 절차를 제안하고 이를 저층의 철근콘 크리트건물의 모델개선에 적용하였다. 대상건물은 전단벽 신설 및 댐퍼부착을 위한 부재의 강재보강을 통해 내진보강이 이 루어진 건물로서 보강전후에 소형 가진기를 이용한 진동실험을 실시하여 동특성을 구하였다. 대상건물의 개선에 사용된 변 수는 기존콘크리트, 신규타설된 콘크리트, 조적의 탄성계수, 신축줄눈부의 스프링계수, 강재보강된 부재의 유효강성비이다. 보강전후 건물의 초기모델을 구축한 후 중심합성법에 따라 개선변수의 값을 변화시키면서 얻은 해석결과를 통해 고유진동 수의 오차와 모드형상의 오차를 나타내는 2개의 반응함수를 구하고, 이를 다목적최적화의 목적함수로 사용하였다

The study for reducing friction in elevation motion of a large television stand using over 50 inches is performed in this paper. The first study attempted to reduce the frictional force the gas seal lip technology. The second study is for optimized piston structure development by comparison pipe orifice and labyrinth orifice. As the result of the first study, in the gas seal lip technology, the outer-inner diameter of Ø20 × Ø8 in the test result of hollow rod is revealed more proper if the weight of 50 inch television assumed as 30. As the result of the second study, the optimized piston structure development through experiment is fixed orifice specification as labyrinth orifice because pipe orifice is founded slip up/down phenomenon of the Ø0.4~1.0 orifice and the labyrinth orifice is not founded that of the Ø0.4~0.6 orifice both tests on 300 mm intervals.

Surge pressure is created by rapid change of flow rate due to operation of hydraulic component or accident of pipeline. Proper control of surge pressure in distribution system is important because it can damage pipeline and may have the potential to degrade water quality by pipe leakage due to surge pressure. Surge relief valve(SRV) is one of the most widely used devices and it is important to determine proper parameters for SRV’s installation and operation. In this research, determining optimum parameters affecting performance of the SRV were investigated. We proposed the methodology for finding combination of parameters for best performance of the SRV. Therefore, the objective function for evaluate fitness of candidate parameters and surge pressure simulation software was developed to validate proposed parameters for SRV. The developed software was integrated into genetic algorithm(GA) to find best combination of parameters.

Structural dynamic system involves random variables conditions such as material property, geometric parameters and applied loads. This uncertainties result from the structural parameter are carefully considered the dynamic structural response in displacement, stress, and natural frequencies. The random vibrational system must be designed to withstand a certain amount of the fluctuation with respect to the uncertainties. Harmonic response of a spring-mass system is mathematically modelled with the probabilistic finite element method using the Monte Carlo simulation. The aim of this paper is to find the optimal lowest frequency for the spring-mass system with random input variables and response parameters to the displacements. The probabilistic design is carried out using ANSYS probabilistic design module in a commercial application software and then the optimal design is sequentially solved. An efficient and practical optimal design evaluation method is proposed for the design of the harmonic system. The numerical results are obtained where the next highest frequency of the system and displacements treated as constraints.

PURPOSES : The objective of this study is to develop an optimized method of mix design for rapid-set lightweight-formed mortar mix. To achieve this objective, the workability, setting time, and compressive strength of mixes under various conditions of mix design were evaluated. METHODS: The water-bonder ratio, fly-ash substitution ratio, and forming agent injection amount were selected as design variables in the study. The fluidity, setting time, density, and strength of the mortar mix were considered as major evaluation criteria of the mixture, and were subsequently utilized to evaluate the characteristics of the mortar mix under various conditions. RESULTS : The observations made from the mix design process are as follows: 1) the air content and fluidity increase as the forming agent ratio and forming agent ratio increase, respectively; 2) the maximum air content is approximately 20%; 3) the accelerating agent decreases the fluidity of the mortar mix by 15% on average; 4) the forming agent injection ratio and fly-ash substitution ratio yield significant effects on the initial and final set times of the mortar mix; 5) as the forming agent injection ratio and fly-ash substitution ratio increase, the compressive strength of the mortar mix decreases; and 6) the 28-day compressive strengths of the forming agent injection ratio and fly-ash substitution ratio yield the most significant effects. CONCLUSIONS: It is concluded that the governing design variables for the rapid-set lightweight-formed mortar mix are the forming agent injection ratio and fly-ash substitution ratio.

An injection unit is the important part which guide the melted resine into the mold. Once injection molding is performed, there will be a pressure of 33 MPa built up inside of injection cylinder body. It was confirmed that the crack occurs by internal stress on the 9 mm material when the machine is used for long time. Because the cylinder rod has material thickness of 9~12 mm during manufacturing process on the cylinder body, there would be 3 mm thickness differences. In this experiment, IDEAS, a computer aided structure analysis software, is used to present the optimized design condition. Insert rod with inner diameter of 9 mm was set as a normal and vary 3 mm in x, y axis direction. When the internal pressure of 33 MPa occurs at the injection unit, fix the x and y direction and find out the stress acting only in z axis. It was confirmed that the stress of 45~82 N/mm 2 was built up when the left of cylinder body had been set 9 mm by using a structure analysis. Also, it has been verified the thickness of the material on the left need to be greater and equal than 12 mm to prevent a material crack by an internal stress.

Numerical analysis using k-ε model of unsteady state was performed to decide the optimal shape of power auxiliary apparatus in automotive engine. In order to obtain auxiliary electric power using coolant in automotive engine, shapes of 3 Types were compared. Furthermore to achieve the confidence of numerical analysis, the results of numerical analysis was compared with those of experiment. As the results, it showed that accuracy of numerical analysis was about 85~98%. Further the optimal shape, in this study, was Type-1, which had outer rounding R32.5, among 3 Types.

본 연구는 표면 반응 분석법을 이용하여 곤드레 데치기 최적 공정 조건을 확립하고 각각의 공정으로부터 생산된 곤드레 추출물로부터 총 페놀 화합물, 플라보노이드의 함량, DPPH 라디칼 소거능 을 분석하였다. 최적 공정 확립을 위한 데치기 공정 범위로 온도는 70℃ - 99℃, 시간은 70 - 170 sec. 로 하였다. 데치기 공정 후 총 페놀 함량의 범위는 13.00 - 35.48 mg/g 이고 최대 예측 총 페놀함량은 35.48 mg/g, 총 페놀 함량의 경향을 보면 데치기 온도에 따라 급격히 감소하다가 증가하는 것으로 보 여 지므로 온도에 의해 더 많은 영향을 받는 것으로 나타난다. 플라보노이드의 함량의 범위는 2.31 - 8.38 mg/g 이고 최대 예측 플라보노이드 함량은 8.38 mg/g 이었다. 플라보노이드 함량의 경향을 보면 데치기 시간에 따라 서서히 증가하다가 급격히 감소하는 것으로 보여 지므로 시간에 의해 더 많은 영향 을 받는 것으로 나타났다. DPPH 라디칼 소거능의 범위는 42.10 - 67.14%이고 최대 예측 DPPH 라디 칼 소거능은 67.14%로 측정 되었다. DPPH의 경향을 보면 데치기 온도에 따라 증가하다가 급격히 감소 하는 것으로 보여 지므로 온도에 의해 더 많은 영향을 받는 것으로 나타난다. 따라서 데치기 공정 최적 조건은 온도 85℃와 시간 150 sec. 로 결정되었다.