PURPOSES : This study aims to provide societal benefits that demonstrate the effectiveness of remodeling projects, thereby providing a basis for activating and systematically and continuously promoting remodeling projects METHODS : Using the International Roughness Index (IRI) and World Bank's HDM-4, a model for vehicle operating costs was estimated. The change in vehicle operating costs was calculated by inputting the pre- and post-remodeling IRI values into the estimated model. Additionally, the future IRI over the life cycle was derived using the results of a study on the changes in pavement conditions between conventional and remodeling methods. The vehicle operating costs for different maintenance alternatives were compared by inputting them into the estimated model. RESULTS : The improvement in road smoothness after the project resulted in an annual vehicle operating cost benefit of approximately 1.6 billion won, with an estimated benefit per kilometer of approximately 64 million won. Furthermore, a comparison of vehicle operating costs for maintenance alternatives over the life cycle revealed that the remodeling method led to savings of 2.1 billion won compared with conventional methods. CONCLUSIONS : The findings of this study will serve as fundamental data supporting the necessity and justification for remodeling projects, particularly in the current scenario, where the need for maintenance of existing roads exhibits a faster growth trend than the extension of new roads. Additionally, this study could be supplemented by further research focusing on the consideration of pavement conditions in unit cost estimation and additional benefit estimation studies tailored to remodeling projects.

콘크리트 포장의 조기 파손을 초래하는 콘크리트 혼합물의 품질 저하는 최근 종종 발생되고 있다. 이로 인한 유지보수 비용 또한 증 가하는 추세이다. 본 연구는 이러한 문제를 해결하고자 콘크리트 배합 시 효과적으로 유변학적 특성을 측정하여 콘크리트 품질을 예 측할 수 있는 시제품 개발을 연구 중이다. 현재 상용화되어 사용되고 있는 ICAR Plus Rheometer 장비의 이론을 변경 적용하여, 본 시제품 Twin Shaft Rheometer mixer를 개발하였다. 동시에 레오미터 장비를 활용해 유변학적 특성을 확인하고 측정하였다. 콘크리트 의 변형과 움직임을 분석하기 위해 수직, 수평 거동의 비교분석을 진행하였고, 흐름 저항성과 토크 점성을 이용하여 유변학적 특성을 기존 장비와 비교 분석하였다. 그 결과 절댓값의 차이는 존재하나 선형적 유사성을 가지는 것을 알 수 있었다. 높은 정확성을 위해 추 가연구는 진행하고 있다. 추가로 슬럼프 측정 센서 또한 개발 진행 중이며, 이 장비는 마이크로파를 통해 매질의 변화를 측정하여 슬 럼프를 유추하는 센서로 더욱 정밀한 결과값을 위해 추가연구 진행하고 있다.

In alignment with South Korea's “3020 Renewable Energy Expansion Plan,” this study focuses on the developing large-scale floating wind turbines. It addresses the challenges of increased size and cost in floating structures for wind turbines over 10MW. This paper details the preliminary design of a novel floating substructure utilizing composite materials(ie, EVA). Structural analysis was performed using ABAQUS, accounting for both typical and extreme wind conditions. Results from the analysis validate that the substructure design is adequately feasible for implementation.

The effects of annealing on the microstructure and mechanical properties of Al–Zn–Mg–Cu–Si alloys fabricated by high-energy ball milling (HEBM) and spark plasma sintering (SPS) were investigated. The HEBM-free sintered alloy primarily contained Mg2Si, Q-AlCuMgSi, and Si phases. Meanwhile, the HEBM-sintered alloy contains Mg-free Si and θ-Al2Cu phases due to the formation of MgO, which causes Mg depletion in the Al matrix. Annealing without and with HEBM at 500oC causes partial dissolution and coarsening of the Q-AlCuMgSi and Mg2Si phases in the alloy and dissolution of the θ-Al2Cu phase in the alloy, respectively. In both alloys, a thermally stable α-AlFeSi phase was formed after long-term heat treatment. The grain size of the sintered alloys with and without HEBM increased from 0.5 to 1.0 μm and from 2.9 to 6.3 μm, respectively. The hardness of the sintered alloy increases after annealing for 1 h but decreases significantly after 24 h of annealing. Extending the annealing time to 168 h improved the hardness of the alloy without HEBM but had little effect on the alloy with HEBM. The relationship between the microstructural factors and the hardness of the sintered and annealed alloys is discussed.

좁은가슴잎벌레는 십자화과작물을 가해하는 해충으로 알려져 있다. 본 연구는 온도가 좁은가슴잎벌레의 발육단계별 발육기간, 성충의 수 명과 산란특성에 미치는 영향을 파악하고자 성충 전 발육단계는 15, 20, 25, 27.5°C에서, 성충은 10, 15, 20, 25, 27.5°C 항온조건에서 조사하였 다. 알과 유충은 항온조건에서 다음 발육 단계로 성공적으로 발육하였다. 알, 유충, 번데기의 발육기간은 온도가 상승할수록 짧아지는 경향을 보 였다. 좁은가슴잎벌레의 발육영점온도, 유효적산온일도는 선형회귀분석을 통해 추정하였으며 알에서 성충출현까지 발육영점온도와 유효적산온 일도는 8.7°C와 344.73DD였다. 좁은가슴잎벌레 발육단계별 최저, 최고 온도의 한계는 Briere함수를 이용하여 추정하였으며 알에서 성충출현 까지 최저, 최고한계는 5.3°C와 40.4°C였다. 성충은 10°C와 27.5°C 범위에서 산란이 가능하였고 21.7°C에서 최대 약 627.5개의 알을 낳는 것 으로 추정되었다. 노화율, 나이별 생존율, 나이별 누적산란율, 온도의존 산란수와 관련된 성충모델들을 작성하였다. 본 연구에서 제시한 온도발육 모형과 성충산란모형은 좁은가슴잎벌레 개체군동태를 이해하는데 유용할 것이며 십자화과작물의 종합적 해충군관리체계를 마련하는데 기초자 료로 활용될것으로 기대된다.

In this study, a THC removal system was developed using an oxidation catalyst to solve the problems of the existing thermal oxidation methods, RTO and RCO. In addition, this system was applied to industrial sites to confirm the VOCs removal efficiency. As a result of testing to remove THC and VOCs by applying the reaction system for THC removal in industrial sites, the THC removal efficiency range is between 99.5% and 99.9%. The treatment efficiency of individual VOCs treated through this system was the lowest at 79.0% for methylethylketone and the highest at 91.3% for acetaldehyde, and the average treatment efficiency was about 85.4%. From these numbers, the performance was superior to the existing RTO and RCO systems that showed THC removal performance. This is due to the fact that the oxidation reaction of the oxidation catalyst is a very fast catalyst surface reaction, and the characteristics of the catalytic oxidation reaction are complete oxidation and oxidation reaction under rarefied conditions. In this study, the catalyst role in the reaction system for THC removal is to process THC simultaneously with the system heat source. This is believed to be because the reaction of the oxidation catalyst is a strongly exothermic reaction and can sufficiently provide the amount of heat necessary for the system. At the same time, an oxidation reaction that breaks the bonds of the THC component also occurs. This reaction is a strong exothermic reaction, which can help the system maintain a high temperature during the reaction, and is considered an effective system for processing high concentrations of THC in actual industrial sites where THC concentrations are high, as in this study.

This study investigated the changes in the cyanogenic glycoside (CN-Glc) content of maesil chung (MC) prepared according to its preparation conditions (i.e., maesil part, sugar type, maesil-sugar mixing ratio, liquid separation) and sugaring-ripening period and the quality characteristics of their products finalized through filtration and heat treatment (85oC, 30 min) with the 6-month ripened MC. The CN-Glc content dramatically decreased when the maesil flesh, isomaltooligosaccharide, maesil:sugar ratio of 5:5, and liquid separation after the 4-month sugaring were applied to the MC production. The CN-Glc content decreased with the ripening period. There was no effect of filtration and heat treatment on the CN-Glc reduction of the MC product. The sugar type predominantly affected the soluble solid and total carbohydrate content of the MC products, and their contents increased in the order of high-fructose corn syrup > sucrose > isomaltooligosaccharide. The MC product at a maesil:sugar ratio of 6:4 exhibited the higher organic acid content. There was no direct association between the total polyphenolic compound content and the preparation conditions of the MC product. Overall, the use of maesil flesh as a maesil ingredient and more than 6-month ripening after liquid separation may be a pivotal factor in producing the cyanogenic glycoside-reduced maesil chung.

The objective of this study was to investigate changes in the cyanogenic glycoside (CN-Glc) content of apricot and plum chungs over the sugaring-ripening period and to evaluate their quality characteristics. The whole and flesh parts of the apricot and plum were mixed with sugar to a mixing ratio of 1:1 (w/w) to prepare their chungs, after which the fruit-sugar mixtures were stored for 13 months. The CN-Glc content dramatically increased within 3-4 months, reached the maximum, and gradually decreased over storage by 13 months. The apricot and plum chungs with seeds exhibited much higher CN-Glc contents than those without seeds. All chungs stored for 10 months were filtrated and treated for 30 min at 85oC to measure their quality characteristics. Similar soluble solid contents (53.4- 53.6oBx) were found in all chungs. The apricot and plum chungs without seeds exhibited the higher concentrations of total carbohydrate, organic acid, and total polyphenolic compounds than those with seeds. In addition, the color of the apricot and plum chungs without seeds was darker and deeper yellow than those with seeds. Overall, the apricot and plum flesh may be better for producing the stone fruit chungs with minimal CN-Glc content and better nutrition.

막대한 예산이 투입되는 국가연구를 기획·관리·확산하는 연구관리 담당자들은 매우 중요한 인력이나, 역할에 관한 연구는 부족한 실정이다. 본 연구는 연구관리 전문기관 담당자에게 필요한 역량요소를 도출하고 역량의 중요도를 확인하고자 하였다. 이를 위해 4가 지 주요요인과 16개의 하위요인을 도출하였고, AHP 기법을 기반으로 설문조사(연구관리 담 당자와 연구자 90명 대상)를 추진하여 우선순위를 도출하였다. 전체 응답자 기준으로 역량의 중요도는 협력적 태도, 소통능력, 연구지식, 목표관리능력과 신의성실 순으로 확인되었으나, 담당자의 경우, 업무와 관련한 역량(규정지식, 판단능력, 정책지식)이 중요하다고 보는 반면, 연구자들의 경우 자신들을 보다 더 지원해 줄 수 있는 역량(협력적 태도, 소통능력)을 보다 더 중시하는 시각차를 볼 수 있었다. 이번 연구는 전문기관 연구관리 담당자의 채용과 역량 개발에 활용할 수 있을 것으로 사료된다.

With the increasing attention to environmental pollution caused by particulate matter globally, the automotive industry has also become increasingly interested in particulate matter, especially particulate matter generated by automobile brake systems. Here, we designed a coating composition and analyzed its mechanical properties to reduce particulate matter generated by brake systems during braking of vehicles. We designed a composition to check the mechanical properties change by adding Cr3C2 and YSZ to the WC-Ni-Cr composite composition. Based on the designed composition, coating samples were manufactured, and the coating properties were analyzed by Vickers hardness and ball-on-disk tests. As a result of the experiments, we found that the hardness and friction coefficient of the coating increased as the amount of Cr3C2 added decreased. Furthermore, we found that the hardness of the coating layer decreased when YSZ was added at 20vol%, but the friction coefficient was higher than the composition with Cr3C2 addition.

In this study, in order to develop a method to efficiently inject essential nutrients necessary for plant growth into wood chips, which are simply used as soil covering materials in the agriculture, landscaping and horticultural industries, the atmospheric pressure dipping method and the vacuum pressure impregnating method are used to improve the plant nutrients injectability and impregnation amount were comparatively analyzed. Nutrient ingredients and 8 major heavy metal contents of wood chips injected with nutrients were analyzed, and soil covering effects were examined by covering wood chips injected with nutrients on soil. Comparing the dipping method and the vacuum pressure impregnation method, it took about 48 hours or more to inject 1,500 g or more of the nutrient aqueous solution into 1 kg of wood chips in the dipping method, but the vacuum pressure impregnation method could be impregnated in about 5 minutes. Components of the impregnated nutrients were detected in proportion to the diluted concentration. As a result of covering the wood chips developed in this study on soil, they showed weakly acidic pH, and the heat insulation and moisturizing effects during the winter season were evaluated to be superior to those of uncovered soil. In the future, wood chips impregnated with nutrients are expected to contribute to the more efficient use of waste wood resources and the long-term supply of nutrients essential for plant growth, reducing excessive use of chemical fertilizers and reducing costs.

PURPOSES : This study aims to analyze and summarize test results related to permeable blocks used for sidewalks and roadways as an alternative to conventional urban road pavement technology, specifically focusing on low-impact development (LID) techniques. Furthermore, it aims to provide reference data on the feasibility of current policy implementation and future policy directions through a longterm analysis of the performance and durability of permeable blocks in sidewalk and roadway construction. METHODS : The research methodology involves (1) conducting a survey on the status and actual conditions of permeability sustainability tests based on the results of permeability persistence tests conducted in Seoul over nine years, from 2013 to 2021; (2) analyzing the differences between the permeability block rating system of Seoul City and that employed by the Ministry of Environment; (3) analyzing the permeability of graded pavement sections in permeable blocks for sidewalks after three years of public use and deriving a regression analysis formula to estimate the maintenance period; (4) analyzing the permeability of pavement sections in permeable blocks for roadways after five years of public use and deriving a regression analysis formula to estimate the maintenance period. RESULTS : This study revealed significant improvements in the performance and quality control of permeable blocks since the implementation of the permeability sustainability test in Seoul in 2013. An analysis of the differences in the permeability coefficient and distribution based on the rating systems of Seoul City and the Ministry of Environment showed that rating system of Seoul City has approximately twice the permeability coefficient quality standard compared to that of the Ministry of Environment. Regression analysis indicated that the firstgrade permeable block was predicted to maintain its permeability for approximately 5.1 years, whereas the third-grade permeable block was predicted to maintain its permeability for approximately 3.1 years. In roadway-permeable block pavements, the first-grade sections maintained excellent quality conditions even after five years, and regression analysis predicted a permeability maintenance period ranging from eight to 17 years. CONCLUSIONS : The correlation analysis of the permeability coefficients based on the common usage period of permeable blocks for sidewalks and roadways presented in this study can provide more accurate estimations of commonality. However, further research under various environmental conditions is required to supplement these findings. Considering the lack of studies on permeable block commonality analysis in Korea, this study highlights the significance of conducting long-term experimental follow-up research to establish commonality prediction formulas for different usage scenarios.

In this study, we aimed to compare the mycelial growth of Pleurotus ostreatus after medium supplementation with various amino acids at different concentrations to select the optimal medium nutrient composition for mycelial growth. The mycelial growth of P. ostreatus was investigated after adding four amino acids (tryptophan, threonine, methionine, and lysine) at 0.5% or 1% to the medium.The rate of P. ostreatus mycelial growthwas faster in the potato dextrose agar (PDA) medium supplemented with threonine at 0.5% or 1% than that of the control, whereas it was inhibited by tryptophan treatment. Supplementation of sawdust mediumwith all amino acids, except tryptophan, at 0.5% did not alter the mycelial growth, compared to the controls. However, addition of any amino acid to sawdust medium at a higher concentration (1%) inhibited the mycelial growth. The laccase acitivity of P. ostreatus mycelium cultured in PDA medium was the highest when threonine was added, and the lowest when tryptophane was added, consistent with the results of the mycelial growth. Therefore, the addition of threonine, methionine, or lysine to PDA medium at a concentration of 0.5-1%was effective for increasing the mycelial growth of P. ostreatus; however, it inhibited mycelial growth insawdust medium, suggesting that the effects of amino acids dependedon the medium nutrient composition.