Vehicle crash analysis a lot of time and manpower in preprocessing for analysis rather than analysis in analytical studies of the situation that is being committed. In this studies involving conflict with an existing automation system of the body is mainly optimized for a particular field, and researchers think that is an inconvenience that can be used in stone until a comprehensive analysis of the bodywork of each study. Therefore, it is very important to development of automotive system for vehicle crash analysis, the research related studies were carried out. In this study, vehicle crash analysis is performed against that can be used for multiple and effectively utilized by system based meshing in an aim to reduce the time and resource that by developing an automotive system. The results of the study, it was possible to construct an automated system the more time consuming mesh generation for vehicle crash analysis.

Share of total accidents in construction accidents construction site accident 70% of small embroidery Reducing the rate of Construction of the entire construction accidents decreased overall is a very meaningful work. Disaster reduction continues to increase despite the efforts of a small construction site(Amount less than 2,000,000,000) for Disaster Reduction In order to identify more clearly the cause of the system and provide the urgently needed measures.

PURPOSES : The bridge section of the expressway has a worse driving environment than the general section. However, traffic safety countermeasures are focused only on the bridge section. Traffic safety countermeasures on the section before entry to the bridge and the section after exit from the bridge are applied only when the bridge has a long-span section. Accordingly, this study will verify the necessity of extending the application of traffic safety countermeasures to areas that are affected by the bridge. METHODS: This study determines the areas that are affected by the bridge as well as the areas that are affected by locations with frequent traffic accidents and suggests the risk factors by affected areas through canonical discriminant analysis. For the analysis, traffic accident data for 3 years, which occurred on bridge sections in six major expressway lines, were used. RESULTS: The numbers of traffic accidents were 469 before the bridge, 281 on the bridge, and 468 after the bridge. The variables that have impact on the seriousness of accidents are as follows: speeding, excess manipulation of the steering wheel, and failure to secure safety distance for accidents that occurred before the bridge section; speeding, excess manipulation of the steering wheel, and dozing off for accidents that occurred on the bridge; and speeding and failure to secure safety distance for accidents that occurred after the bridge section. CONCLUSIONS : Areas affected by the bridge show higher accident rates than the bridge section; therefore, imposing traffic safety countermeasures on the integrated section of the bridge and the affected areas is required. It is believed that the results suggested in this study could be effectively used in the prevention of traffic accidents by imposing custom-made safety countermeasures for each section.

This study carried out passenger safety assessment by real car crash simulation of composite post structures for road facilities. The effects of different material properties of composites for various parameters are studied using the LS-DYNA finite element program for this study. In this study, the existing finite element analysis of steel post structures using the LS-DYNA program is further extended to study dynamic behaviors of the structures made of various composite materials. The numerical results for various parameters are verified by comparing different models with displacements and stress distribution occurred in the post and car.

The automotive industry is moving from the internal combustion engine to electric drive motors. Electricmotors uses a high voltage system requiring the development of resources and components to shield the system. There-fore, in this study, we analyze electromagnetic interference (EMI) shielding effectiveness (SE) characteristics of an autocrash pad according to the ratio of electrically conductive materials and propylene. In order to combine good mechan-ical characteristics and electromagnetic shielding of the automotive crash pad, metal-coated glass fiber (MGF) manufac-turing methods are introduced and compared with powder-type methods. Through this study, among MGF methods, wesuggest that the chopping method is the most effective shielding method.

This study carried out real car crash simulation of composite post structures for road facilities. The effects of different material properties of composites for various parameters are studied using the LS-DYNA finite element program for this study. In this study, the existing finite element analysis of steel post structures using the LS-DYNA program is further extended to study dynamic behaviors of the structures made of various composite materials. The numerical results for various parameters are verified by comparing different models with displacements and stress distribution occurred in the post and car.

항공기 연료셀은 추락 상황에서 승무원의 생존성과 직결되는 중요 구성품으로 회전익 항공기에 적용되고 있는 내충격성 연료셀은 추락시 승무원의 생존성 향상에 큰 역할을 하고 있다. 미육군은 항공기가 처할수 있는 다양한 상황에서 연료셀이제 기능을 발휘할 수 있도록 1960년대 초부터 MIL-DTL-27422 이라는 연료셀 개발규격을 제정하여 현재까지 적용해 오고있다. 해당 개발규격에 규정된 시험 중에서 충돌충격시험은 연료셀의 내충격 성능을 검증하는 시험으로써, 해당 시험을 통과하는 연료셀은 생존가능 충돌환경에서 화재가 발생하지 않아 승무원의 생존성이 대폭 향상될 수 있음을 의미한다. 그러나 충돌충격시험은 작용하는 하중 수준이 너무 높기 때문에 실패 위험성이 가장 큰 시험이기도 하다. 연료셀이 해당 시험을 통과하지 못하는 경우에는 재시험을 위한 비용과 준비기간이 상당히 소요되어 항공기 개발일정에 심각한 지장을 초래할 가능성도 높다. 따라서, 연료셀 설계 초기부터 내충격성능 만족여부에 대한 예측을 위해 충돌충격시험의 수치해석을 통한 실물시험에서의 실패 가능성을 최소화해야 한다는 필요성이 제기되어 왔다. 본 연구에서는 충돌모사 프로그램인 LS-DYNA에서 지원하는 유체-구조 연성해석 방법인 SPH 방법을 사용하여 연료셀 충돌충격시험 수치 모사를 수행하였다. 수치해석 조건으로 MIL-DTL-27422에서 요구하는 시험조건을 고려하였고, 실물 연료셀의 시편시험을 통해 확보한 물성데이타를 해석에 반영하였다. 그 결과로 연료셀 자체의 응력수준을 평가하고 취약부위에 대한 고찰을 수행하였다.

Recently imported vehicles are increasing rapidly and related vehicle accidents have also increased. In addition, the number of accident in 2010 was approximately 205,000 cases, about 6,000 billion to repair the vehicle accident was paid. RCAR low-speed crash tests to calculate the imported car insurance repairs, domestic cars and imported car repairs were compared. Average repair cost 2,920,000 won in domestic cars and imported cars are 14,570,000 won, imported cars were approximately five times higher than domestic cars. The results of comparing the total repair cost, imported vehicle repairs to the front of the T-car was the highest, rear repairs to the C-car was the highest. New car value for repairs, parts price, damage in terms of imported cars were higher than that of the domestic cars. In order to avoid the social costs of spending, calculated based on proper repairs on imported vehicles, improvement of excessively high parts prices and the repairman cost are needed.

PURPOSES: Using the collected data for crash, traffic volume, and design elements on ramps between 2007 and 2009, this research effort was initiated to develop traffic crash prediction models for expressway ramps. METHODS: Three negative binomial regression models and three zero-inflated negative binomial regression models were developed for individual ramp types, including direct, semi-direct and loop, respectively. For validating the developed models, authors compared the estimated crash frequencies with actual crash frequencies of twelve randomly selected interchanges, the ramps of which have not been used for model developing. RESULTS: The results show that the negative binomial regression models for direct, semi-direct and loop ramps showed 60.3%, 63.8% and 48.7% error rates on average whereas the zero-inflated negative binomial regression models showed 82.1%, 120.4% and 57.3%, respectively. CONCLUSIONS: Conclusively, the negative binomial regression models worked better in traffic crash prediction than the zero-inflated negative binomial regression models for estimating the frequency of traffic accidents on expressway ramps.

Construction companies with the highest proportion in death crash has been devoting much effort to prevent the crash accidents. In general, a crash-proof worker has been wearing a seatbelt. However, the G construction company had happened in industrial settings when workers fail to abide by the rules. The Carabiner, one of the composing of Safety Belt, must endure the Allowable Load. In this study, the Industrial accidents and cause of the crash analysis in G Construction company is performed by empirical research. And we have been studied the empirical research to setting up of the allowable limit for Carabiner.

According to a statistics, a number of traffic accident by bridge pier and independent fixed object crash accident has been increased. we evaluated a car damage and passenger injury through vehicle accident reconstruction test of independent fixed object crash accident. A damage of crash accident car based on accident investigation report was similar to demage of 27km/h reconstruction test car, and therefore we can find the speed of crash accident car is 20km/h～30km/h. It is very low that the skull fracture and injury possibility of AIS 4 above in 37km/h and 27km/h reconstruction test car. It is very high that injury possibility in 70km/h reconstruction test car. Also, it is not high that impact of the driver and passenger's lower body(thigh, shin, ankle) in 37km/h and 27km/h reconstruction test car. On the other hand, it is very high that impact of head, chest and thigh of the driver and passenger in 70km/h reconstruction test car.

In this study, the performance of a steel-FRP composite bridge safety barrier was evaluated through the vehicle crash test. Glass fiber and polyester resin were used for FRP. The structural strength performance, the passenger protection performance, and the vehicle behavior after crash were evaluated corresponding to the vehicle crash manual. As the result, A steel-FRP composite safety barrier was satisfied with the required performance.

본 논문에서는 컴퓨터 시뮬레이션을 통해 강재-FRP 합성 교량용 방호울타리의 성능을 분석하였다. FRP는 Surface veil, DB 그리고 Roving 섬유로 구성하였다. FRP의 적층을 고려하기 위해 LS-DYNA에서 제공하는 재료모델 MAT58을 사용하였다. 강관과 FRP의 접촉조건을 고려하기 위해 Spot weld 옵션을 사용하였다. 실차충돌 실무 업무편람에 따 라 구조적 강도성능, 탑승자 보호성능 및 충돌 후 차량의 거동에 대한 성능평가를 실시하였다. 강재-FRP 합성 방호 울타리는 성능평가를 만족하였다.

교통사고발생시 사고 심각도에 영향을 미치는 요인과 그 관계를 이해하는 것은 기하구조나 환경 측면에서 교통사고 발생을 예방하고 운전자와 사고 차량의 특성을 이해하는데 도움을 준다. 본 연구에서는 계층 이항 로지스틱모형에 의해 고속도로 교통사고 심각도에 영향을 미치는 요인을 파악하고 영향변수 간 차이를 나타내는 비교위험도(odds ratio)를 도출하였다. 사고 심각도는 인명피해와 차량피해로 구분하여 사망사고모형과 차량완파사고모형을 구축하였다, 종속변수는 사망자 발생과 완파차량 발생 여부이며, 각각 사고-탑승자, 사고-차량의 2수준 계층구조를 적용하였다. 추정 결과 설명변수의 고정효과는 두 모형이 유사한 결과를 보이나 종속변수의 속성에 따라 차별화된 결과를 나타내기도 하였다. 본선과 진출입부에서의 사고가 가장 위험하며, 중앙선 침범과 통행위반, 과속 사고의 상해나 차량 파손 위험도가 높고, 충돌사고와 추돌사고, 화재 사고의 피해가 크다. 사고 심각도는 노면 상태나 시야 조건 등 외부환경에 영향을 받으나 기하구조 조건은 관련이 없다.

교통사고 원인분석 및 사고예방을 위해서는 교통사고 유발요인에 대한 이해가 필요하다. 기존 연구에서는 기하구조, 운전자 특성 등의 요인을 고려하여 연구를 진행하였다. 그러나, 운전자 특성요인 분석에 사용된 자료는 검지기에서 측정된 집계된 속도로써, 속도 변화량을 이용한 사고분석연구에는 한계가 존재한다. 따라서, 본 연구에서는 차량의 속도변화 등의 수집이 용이한 센서를 이용하여 자료를 수집하였다. 가속도자료 및 기하구조 특성을 나타내는 변수를 설정하고, 사고자료와 매칭을 통해 사고개연성이 높은 잠재적 변수로의 적합성을 평가하였다. T-test, 이항 로지스틱 회귀분석을 사용했으며, T-test 결과로써 도출된 변수를 이항 로지스틱 회귀분석의 독립변수에 적용하고, 사고발생 유 무를 종속변수로 설정하였다. 분석결과, 5개의 변수가 사고발생에 영향을 주는 변수로 도출되었다. 또한, 도출된 모형은 사고발생구간의 예측에 적용할 수 있는 타당성을 확보하는 것으로 분석되었다. 본 연구에서 도출된 위험 운전행태 변수 및 모형은 프로브차량에 설치하여 활용할 수 있는 장치 등에 적용시켜 사고위험도 및 안전성 평가에 활용할 수 있을 것으로 기대된다.

본 연구에서는 고속도로를 대상으로 각각의 구간에 대한 선형유형을 구분하여 사고빈도모형을 개발하였다. 현재 사고빈도모형 부문의 연구는 주로 고속도로 구간 전체를 대상으로 한 연구가 대부분이기 때문에 거시적인 측면에서 사고빈도모형이 개발되었다고 할 수 있으며, 이에 따라 각각의 구간특성이 정확히 반영되지 않은 상태에서의 사고빈도를 예측하였다고 볼 수 있다. 본 연구에서는 이러한 문제점을 인식하여, 동질구간 분할법을 사용하여 고속도로의 평면선형을 직선부, 곡선부, 연속곡선부로 구분하였고, 이를 군집분석을 통하여 직선부와 곡선부의 유형을 구분하여 고속도로의 각각의 구간별 특성을 반영한 사고빈도모형을 구축하였다. 본 연구 결과는 고속도로 각 구간의 사고빈도를 예측하는데 있어 더 정확하고 합리적인 결과를 도출해 낼 것이라 판단한다.

According to a statistics, in recent three years number of traffic accident and casualty remain stand still while casualty by car to car side crash has been increased. This phenomenon is attributed to the two main factors. One is vehicle structure and the other is vehicle safety regulation which does not appropriately reflect current market situation. The distance from vehicle side door to occupant is kind of short compare to vehicle front to occupant, so the likelihood of occupant injury or death at side crash accident is higher than any other types of accident. Even Korean government runs to evaluate and improve vehicle side impact crashworthiness, this program does not reflect current vehicle fleet cause it is based on vehicle fleet of more than 20 years ago. In this paper, three sets of car to car side impact test have done to evaluate occupant injury probability and aggressivity of SUV to passenger vehicle, and based on this result the way to reduce injury and fatality likelihood at side crash is recommended.