As an alternative to coupling beam in shear wall system, application of the damper which can dissipate energy is increasing. In this study, lintel beam type steel damper which is simple to construct and change depending on design load was proposed. Cyclic loading test was conducted to compare reinforced concrete coupling beam and lintel beam type steel damper. The test results showed that lintel beam type steel damper has higher initial stiffness and energy dissipation capacity than reinforced concrete coupling beam.

Recently, measures for reducing noise and vibration of a railroad station are actively being developed to enhance its property value and comfort level of passengers. In this paper, the applicability of the recently developed vibration mitigation method utilizing a platform TMD (Tuned Mass Damper) by installing a spring-damper system beneath the platform is experimentally verified using a bench scale structure. The two-story bench scale structure is built to simulate a real railroad station, and vibration reduction effect is verified by comparing acceleration before and after applying the platform TMD at the 2nd floor of the structure. The design parameters of the platform TMD system is determined based on vibration analysis result and the MTMD (Multiple TMD) theory recently developed to enhance the effectiveness of the platform TMD method. The vibration is excited to the bench-scale structure using a vibrator. The performance test result for a spring-damper system is also presented. The result of the experiment reveals that the platform TMD method can reduce the vibration of the bench-scale structure by greater than 5dB(V).

When reinforcing an existing reinforced concrete beam-column building with a precast concrete panel, special connection between the PC member and the RC member is required to solve the time dependent deformation of the RC member and to receive the large shear forces. The aim of this study is to obtain the shear strength of upper connection between the existing RC beam-column and infilled PC wall panels in experimentally and theoretically. Thus, the static shear loading tests were conducted on the 6 specimens with the plate connection. Shear failure was resulted from the weakest portion of interior PC panel, exterior RC, and the connection, when the PC portion which located at the center of specimen was pulled upward from the bottom. T he experimental result was compared with analytical result from ACI 318M-14 Chapter 17 for the shear strength of post-installed anchor and PCI Handbook 7th edition 6.8 Structural Steel Corbel (PCI Design Handbook 7th edition, 2010) for the strength of cast-in H-beam. The analytical and experimental results show final failure at the same location. The failure loading of experiment showed larger than average 6% to that of the analysis.

1970년대 이후 한국의 빠른 경제성장 동안에 수로나 철도 등 많은 지중구조물들이 건설되었다. 1988년에 내진설계가 의무 화되었으나, 1988년 이전의 지중 구조물들은 내진설계가 반영되지 않았다. 따라서, 이러한 지중 구조물들은 지진이 일어났을 때 안전성을 확보하기 위해 효과적인 내진 보강방법이 필요하다. 그러한 이유로, 본 연구에서는 새롭게 개발된 보강재를 이 용한 RC 박스 지중 구조물 우각부 보강공법의 내진성능에 대하여 분석하였다. 이 공법은 박스구조물 우각부에 Pre-flexed member를 설치하여 외력에 저항력을 증대시키는 원리이다. 타당성을 검증하기 위해서 새로이 개발된 보강재와 기존의 보강 재를 실험과 유한요소해석으로 비교하였다. 유한요소모델에서 강재의 비선형 모델은 J2 Plasticity Model을 기초로 하고 콘 크리트는 CEB-FIP MODEL CODE 1990로 모델링되었다. 또한, 설계반영을 위한 박스 구조물과 보강재와의 합성률을 산정 하였다. 보강재와 박스구조물은 Tie에 의해 완전 부착된 상태의 연결조건 하에서 해석이 수행되었으며, 하중-변위곡선에서 실험과 유한요소해석의 결과가 서로 일치하였다.

Soil-foundation-structure interaction (SFSI) is one of the important issues in the seismic design for evaluating the exact behavior of the system. A seismic design of a structure can be more precise and economical, provided that the effect of SFSI is properly taken into account. In this study, a series of the dynamic centrifuge tests were performed to compare the seismic response of the single degree of freedom(SDOF) structure on the various types of the foundation. The shallow and pile foundations were made up of diverse mass and different conjunctive condition, respectively. The test specimen consisted of dry sand deposit, foundation, and SDOF structure in a centrifuge box. Several types of earthquake motions were sequentially applied to the test specimen from weak to strong intensity of them, which is known as a stage test. Results from the centrifuge tests showed that the seismic responses of the SDOF structure on the shallow foundation and disconnected pile foundation decreased by the foundation rocking. On the other hand, those on the connected pile foundation gradually increased with intensity of input motion. The allowable displacement of the foundation under the strong earthquake, the shallow and the disconnected pile foundation, have an advantage in dissipating the earthquake energy for the seismic design.

선박용 디젤엔진 배기가스에 포함된 입자상물질(PM) 가운데서 블랙카본(BC)은 극지방의 해빙을 촉진시키고 온난화를 유발하는 원인물질로서 큰 주목을 받고 있다. 본 연구에서는 향후 예상되는 PM/BC 배출 규제에 선제적으로 대응하고, 저감기술 개발 및 실증을 위한 기초연구의 일환으로 한국해양대학교 실습선 한바다호를 이용하여 실제 운항 중에 주기관의 배기관 수 포인트에서 PM을 샘플링하여 HR-TEM을 통해 그 구조와 특성을 분석하였다. 또한 배기가스 분석기를 이용하여 운전조건별 배기가스 내 유해물질의 배출 경향을 확인하였다. 분석 결과 엔진에서 배출된 PM의 구조는 구형 입자들의 촘촘하지 않은 체인형 결합으로 이루어져 있으며, 과급기로부터 멀어질수록 온도 저하에 의한 응집이 더 많이 관찰되었고 BC 특유의 graphitic 구조를 잃어가면서 점점 amorphous 구조를 띠는 경향이 나타났다. 또한 배기가스 분석을 통해 엔진 회전수가 증가할수록 배기 내 PM의 농도는 감소할 것으로 예측되었다.

층면구조 안정성 다이어그램은 층면구조가 주어진 입도와 유속에서 나타나는 층면구조의 모양과 크기를 지시한다. 이 다이어그램은 대부분 수조실험에 의해 획득한 실험 데이터를 기반으로 작성되었다. 일반적으로, 수조실험은 입자의 크기와 유속사이의 관계를 이해하기 위해 분급이 좋고 단일입도의 분포를 보이는 퇴적물을 이용하여 수행되었다. 이 다이어그램에 의하면, 세립사와 중립사 퇴적물 표면에서 유속이 빨라지면서, 평행층에서 연흔이 형성되기 시작한다. 이 연구의 목적은 층면구조 안정성 다이어그램의 결과가 실험을 통하여 잘 재현되는지를 확인하고, 분급이 좋은 퇴적물과 달리 분급이 불량한 경우인 이정 입도 분포를 보이는 사질 퇴적물에서도 잘 재현되는지 확인하는 것이다. 본 연구 실험 결과는 2D 연흔이나 3D 연흔 층면구조가 형성되기 위해서, 분급이 불량한 퇴적물의 경우에, 분급이 좋은 퇴적물보다 더 높은 유체의 유속과 전단응력이 필요하다는 것을 보여주고 있다. 탄산염 퇴적물은 수력학적 분급작용이 활발하지 않으며, 퇴적물의 구성이 알로켐과 기질로 이루어지는 이정 입도 분포를 보이는 퇴적물로서 일반적으로 분급이 불량한 특징을 가지고 있다. 따라서, 실험의 결과는 탄산염 퇴적물에서 층면구조 형성을 위해 쇄설성 퇴적환경의 퇴적물 보다 더 높은 유속이 필요할 수 있음을 제안하고 있다. 분급이 불량한 퇴적물 입자가 침식되어 이동기 위해 더 높은 에너지와 유속이 필요하다는 것은 분급 효과, 마찰 효과, 안정성 효과, 갑옷 효과 등이 복합적으로 작용한 결과로 설명될 수 있을 것이다. 본 연구는 예비적 고찰로서, 이어지는 연구를 통해 이러한 현상을 과학적으로 설명하고 입도와 층면구조 형성의 상관성을 보다 정교하게 규명하고자 한다.

To investigate earthquake responses of structures with basements affected by soil deposits, centrifuge tests were performed using an in-flight earthquake simulator. The test specimen was composed of a single-degree-of-freedom structure model, a basement and sub-soil deposits in a centrifuge container. The test parameters were the dynamic period of the structure model, boundary conditions of the basement, existence of soil deposits, centrifugal acceleration level, and type and level of input earthquake accelerations. When soil deposits did not exist, the earthquake responses of the structures with fixed basement were significantly greater than those of the structure without basement. Also, the earthquake responses of the structures with the fixed basement surrounded by soil deposits were amplified, but the amplifications were smaller than those of the structures without basement. The earthquake responses of the structures with the half-embedded basement in the soil deposits were greater than those estimated by the fixed base model using the measured free-field ground motion. The test showed that the basement and the soil deposit should be simultaneously considered in the numerical analysis model, and the stiffness of the half-embedded was not effective.

The purpose of this study is to present a method that can estimate the height of reaction facilities for large structural experiment through load flow as primary design procedure. The characteristic of the load transmission according to the type of experiment was analyzed to obtain tensile and compressive forces occurring on the reaction facilities. Strong walls that are affected by the bending moment is applied the post-tensioning method, and the strong floor under the control of the tension and compression is designed in accordance with the load flow. And the optimum cross-section of the reaction facilities was obtained by comparing the stresses of the tensile stress and crack the concrete. Through validating elastic analysis, the design results were satisfied a given design conditions.

Cap decks used in slim floor system for reducing floor height act as molds for forming floor slabs in structures with a span of up to 6m without temporary supports. When deep decks are employed in a structure with a span of more than 6m, the problem of defection occurs. This study suggests placing tendons at the ends of cap decks in order to create cambers and control defection when preload is applied. Uniformly distributed load was applied by an UTM to the two L/4 points of specimens to observe the deflection of preloaded cap decks. For the test, three 7.5m specimens were fabricated. One of them was a plain cap deck specimen and the others were those with tendons (PC strands or steel bars.

제올라이트 분리막은 미세기공이 결정구조에서 비롯되기 때문에 매우 좁고 균일한 미세기공 구조를 갖는 것으로 알려져 있다. 따라서 다공성 지지체 표면에 결함이 없는 균일한 제올라이트 분리층을 안정적으로 형성하기 위한 연구는 매우 중요한 부분이다. 본 연구에서는 다공성 알루미나 지지체 표면에 물/알코올 분리성능이 우수한 투과증발용 NaA, CHA 제올라이트 분리막을 형성시키기 위하여 50-100 nm 크기의 종결정을 도입한 후 수열합성법으로 이차성장시켜 분리막을 제조하였다. 그리고 분리층에 존재하는 비 제올라이트 기공구조(non-zeolitic pore structure)를 상세하게 분석하기 위하여 H2,N2,SF6 등의 단일 가스 투과 거동을 분석함으로써 비제올라이트 기공의 크기를 예측하고자 하였다.

It has been many efforts for reinforcement of existing structure since the number of earthquake has been increased world widely. Especially the occurrence of earthquake surrounding area of Korean peninsular is dramatically increased. Since the buildings in Korea have not been designed to carry the lateral and shear force caused by earthquake, the building will experience massive damages even under moderate earthquake. For this reason, the viscoelastic damper is proposed in this paper to enhance the earthquake resistance of a steel frame buildings. The viscoelastic dampers have been able to increase the overall damping of the structure significantly, hence improving the overall performance of dynamically sensitive structures. In this paper, Viscoelastic dampers designed are consists of FRP panel and viscoelastic material. In this paper, evaluate the performance of the viscoelastic damper through the experiment.

Until recently, almost all ETFE film structures that have been erected is the cushion type because there are problems at lower allowable strength under elastic range and viscosity behaviour such as creep and relaxation of ETFE films under long-term stresses. But the number of tension type structures is currently increasing. This paper proposes the stretch fabrication of ETFE film to verify the applicability of ETFE films to tensile membrane structures. First of all, to investigate the possibility of application on tensile membrane structures, the stretch fabrication test is carried out, and it is verified that it is possible to increase the yield strength of the film membrane structures. After simulating the experiment also carries out an analytical investigation, and the effectiveness of the elasto-plastic analysis considering the viscous behavior of the film is investigated. Finally, post-aging tension measurement is conducted at the experimental facilities, and the viscosity behavior resulting from relaxation is investigated with respect to tensile membrane structures.

구조실험을 위한 데이터 모델은 구조실험에 관련된 실험정보를 정형화하여 표현하므로 데이터 저장소를 개발하는데 이용할 수 있다. 데이터 모델은 특히 대규모의 구조실험정보 또는 일반적인 다양한 실험정보를 위한 데이터 저장소에 효과적인데 예를 들면 NEES에서 개발한 NEEShub Project Warehouse가 있다. 본 논문은 데이터 모델의 구성과 사용을 평가하기 위한 평가요소를 제안하고 있다. 클래스의 속성이 값을 갖는지를 의미하는 AVE(attribute value existence)란 용어를 도입하여 속성의 사용성에 대한 Attribute AVE, 클래스의 사용성에 대한 Class AVE, 하위레벨에 있는 클래스를 포함하는 Class Level AVE, 하나의 프로젝트의 모든 클래스를 포함하는 Project AVE, 모든 프로젝트를 포함하는 데이터 모델에 대한 Data Model AVE를 정의하였다. 이러한 평가요소들을 NEES 데이터 모델의 프로젝트들에 적용하였는데 데이터 모델내의 클래스와 객체에 대한 사용성을 수치적으로 기술하여 평가하는 것이 가능하였다.

매년 증가하고 있는 풍해에 대한 대책으로서의 내풍설계는 필수적이다. 사과나무 지주시스템의 내풍설계를 위해서는 우선적으로 사과나무에 작용하는 풍하중을 파악해야 하고, 이를 위해서는 사과나무의 항력계수 산정이 필요하다. 기존 항력계수 산정 방법에서 발생할 수 있는 실험적 오차 등의 문제점을 보완하고자, 하중 측정 장치의 제작을 통한 풍하중 직접 측정 및 이를 통한 항력계수의 역추정 과정을 수행하였다. 풍속이 증가할수록 항력계수는 감소하며 점차 수렴하는 경향을 나타냈으며, 풍속 30m/s 일 때, 전면적 기준 약 0.176, 순면적 기준 약 0.356 의 값을 갖는 것으로 나타났다.

Large spatial structures can not easily predict the dynamic behavior due to the lack of construction and design practices. The spatial structures are generally analyzed through the numerical simulation and experimental test in order to investigate the seismic response of large spatial structures. In the case of analysis for seismic response of large spatial structure, the many studies by the numerical analysis was carried out, researches by the shaking table test are very rare. In this study, a shaking table test of a small-scale arch structure was conducted and the dynamic characteristics of arch structure are analyzed. And the dynamic characteristics of arch structures are investigated according to the various column cross-section and length. It is found that the natural vibration periods of the small-scaled arch structure that have large column stiffness are very similar to the natural vibration period of the non-column arch structure. And in case of arch structure with large column stiffness, primary natural frequency period by numerical analysis is very similar to the primary natural frequency period of by shaking table test. These are because the dynamic characteristics of the roof structure are affected by the column stiffness of the spatial structure.

The new rotary friction damper was developed using several two-nodal rotary frictional components with different clamping forces. Because of these components, the rotary friction damper can be activated by building movements due to lateral forces such as a wind and earthquake. In this paper, various dependency tests such as displacement amplitude, forcing frequency and long term cyclic loading were carried out to evaluate on the structural performance and the multi-slip mechanism of the new damper. Test results show that the multi-slip mechanism is verified and friction coefficients are dependent on displacement amplitute and forcing frequency except long term cyclic loading.