This study aimed to investigate the validation and modify the analytical method to determine quercetin- 3-o-gentiobioside and isoquercitrin in Abelmoschus esculentus L. Moench for the standardization of ingredients in development of functional health products. The analytical method was validated based on the ICH (International Conference for Harmonization) guidelines to verify the reliability and validity there of on the specificity, linearity, accuracy, precision, detection limit and quantification limit. For the HPLC analysis method, the peak retention time of the index component of the standard solution and the peak retention time of the index component of A. esculentus L. Moench powder sample were consistent with the spectra thereof, confirming the specificity. The calibration curves of quercetin-3-o-gentiobioside and isoquercitrin showed a linearity with a near-one correlation coefficient (0.9999 and 0.9999), indicating the high suitability thereof for the analysis. A. esculentus L. Moench powder sample of a known concentration were prepared with low, medium, and high concentrations of standard substances and were calculated for the precision and accuracy. The precision of quercetin-3-o-gentiobioside and isoquercitrin was confirmed for intraday and daily. As a result, the intra-day precision was found to be 0.50-1.48% and 0.77-2.87%, and the daily precision to be 0.07-3.37% and 0.58-1.37%, implying an excellent precision at level below 5%. As a result of accuracy measurement, the intra-day accuracy of quercetin-3-o-gentiobioside and isoquercitrin was found to be 104.87-109.64% and the daily accuracy thereof was found to be 106.85-109.06%, reflecting high level of accuracy. The detection limits of quercetin-3-o-gentiobioside and isoquercitrin were 0.24 μg/mL and 0.16 μg/mL, respectively, whereas the quantitation limits were 0.71 μg/mL and 0.49 μg/mL, confirming that detection was valid at the low concentrations as well. From the analysis, the established analytical method was proven to be excellent with high level of results from the verification on the specificity, linearity, precision, accuracy, detection limit and quantitation limit thereof. In addition, as a result of analyzing the content of A. esculentus L. Moench powder samples using a validated analytical method, quercetin-3-o-gentiobioside was analyzed to contain 1.49±0.01 mg/dry weight g, while isoquercitrin contained 1.39±0.01 mg/dry weight g. The study was conducted to verify that the simultaneous analysis on quercetin-3-o-gentiobioside and isoquercitrin, the indicators of A. esculentus L. Moench, is a scientifically reliable and suitable analytical method.

본 연구는 다양한 상대습도(11~93%) 조건에서 해조류의 미생물 안정성 및 품질특성에 미치는 영향을 조사하였다. 미생물 안정성은 저장 중 대장균군, 일반세균, 효모 및 곰팡이수를 분석하였다. 일반세균은 상대습도 69~93%에서 4.40~7.00 log CFU/g, 효모 및 곰팡이는 4.20~6.40 log CFU/g로 상대습도 69%이상 조건에서 일반세균, 효모 및 곰팡이의 수가 급격하게 증가하였다. 고결현상은 상대습도 11~53% 조건에서는 일어나지 않았으나 69, 81, 93% 조건에서는 각각 86.9, 99.45, 99.98%로 높은 고결현상을 가지는 것으로 나타났다. 색도는 상대습도가 높아질수록 L값과 b값이 감소하였고, a값이 증가하여 갈변현상이 일어났다. 또한, 총 페놀함량(9.10~8.66 mg GAE/100 g dw), ABTS 소거능(24.20~24.18 mg AAE/100 g dw), FRAP(15.34~15.33 mg Fe(II)/100 g dw)활성은 저장 중 상대습도 11~33%에서 가장 높게 유지되었다. 그러나, 상대습도 43~93%에서 저장 중 총 페놀함량(8.66~4.00 mg GAE/100 g dw), ABTS(22.57~4.50 mg AAE/100 g dw), FRAP(13.06~4.00 mg AAE/100 g dw)활성이 감소하는 것으로 나타났다. 상대습도 81% 조건에서 ABTS 및 FRAP이 1/3배로 감소하였고, 93% 조건에서 총 페놀함량, ABTS 및 FRAP이 각각 1/2배, 1/5배, 1/3배로 감소하였다. 따라서, 일반세균, 효모 및 곰팡이의 성장 억제, 고결현상 방지, 갈변억제, 높은 총 페놀함량과 항산화활성 유지를 위해서는 상대습도 53% 이하의 조건에서 보관하는 것이 미생물 안정성 및 품질특성 유지에 효과적일 것으로 판단된다.

The purpose of this study was to evaluate cookies prepared with five different quantities (0, 5, 10, 15, and 20%) of watermelon powder (WP). This study analyzed quality characteristics, consumer liking, and CATA (check-all-that-apply) of the samples. The density and pH of the cookie dough and the L-value of the cookies tended to decrease as the amount of watermelon powder increased (p<0.05), whereas the spread factor, a-value, and hardness of the cookies tended to increase as the amount of watermelon powder increased (p<0.001). The b-value tended to increase up to WP10, but it tended to decrease from WP15 (p<0.001). The results of the evaluation of consumer liking showed that overall liking was the highest for WP5 and lowest for WP20 (p<0.05). In the analysis of the CATA survey, the main reasons for liking for all the samples were ‘Appearance’, ‘Color’, ‘Sweet taste’, ‘Nutty odor/flavor’, ‘Crispiness’, and ‘Familiarity’. WP5 showed the most diverse reasons for being liked. The common reason for disliking samples with the addition of watermelon powder was ‘Residual feel in the mouth’. In the correspondence analysis, attributes of ‘Stale taste’, ‘Clean taste’, ‘Softness’, ‘Familiarity’, ‘Moistness’, ‘Color’, ‘Blandness’ were detected in the WP0 and WP5. The results indicate that WP5 with a 5% supplementation of watermelon powder is appropriate for improving the quality and consumer acceptability of the cookies.

In this study, we report the microstructure and characteristics of Ag-SnO2-Bi2O3 contact materials using a controlled milling process with a subsequent compaction process. Using magnetic pulsed compaction (MPC), the milled Ag-SnO2-Bi2O3 powders have been consolidated into bulk samples. The effects of the compaction conditions on the microstructure and characteristics have been investigated in detail. The nanoscale SnO2 phase and microscale Bi2O3 phase are well-distributed homogeneously in the Ag matrix after the consolidation process. The successful consolidation of Ag-SnO2-Bi2O3 contact materials was achieved by an MPC process with subsequent atmospheric sintering, after which the hardness and electrical conductivity of the Ag-SnO2-Bi2O3 contact materials were found to be 62–75 HV and 52–63% IACS, respectively, which is related to the interfacial stability between the Ag matrix, the SnO2 phase, and the Bi2O3 phase.

This study evaluated the quality characteristics and antioxidant activities of cookies after adding black ginseng powder at ratios of 0%, 1%, 3%, 5%, and 7%, and the potential of black ginseng as a functional food. The moisture content increased with an increase in the black ginseng powder content while the pH decreased. The L value d ec reased with increase in the black ginseng powder content while the a and b values increased. The hardness decreased with increase in the black ginseng powder content. Notably, antioxidant activities, such as 2,2-diphenyl-1-picryl-hydrazyl (DPPH), 2-2'-azinobis(3-ethylbenzothiazoline-6-sulfonic acid)diammonium salt (ABTS) radical scavenging showed the highest increases in cookies containing 7% black ginseng powder. The total phenol and flavonoid contents significantly increased according to the amount of black ginseng powder added. These results suggest that black ginseng powder can be applied to cookies to achieve high quality and antioxidant activity.

Recently, high-entropy carbides have attracted considerable attention owing to their excellent physical and chemical properties such as high hardness, fracture toughness, and conductivity. However, as an emerging class of novel materials, the synthesis methods, performance, and applications of high-entropy carbides have ample scope for further development. In this study, equiatomic (Hf-Ti-Ta-Zr-Nb)C high-entropy carbide powders have been prepared by an ultrahigh- energy ball-milling (UHEBM) process with different milling times (1, 5, 15, 30, and 60 min). Further, their refinement behavior and high-entropy synthesis potential have been investigated. With an increase in the milling time, the particle size rapidly reduces (under sub-micrometer size) and homogeneous mixing of the prepared powder is observed. The distortions in the crystal lattice, which occur as a result of the refinement process and the multicomponent effect, are found to improve the sintering, thereby notably enhancing the formation of a single-phase solid solution (high-entropy). Herein, we present a procedure for the bulk synthesis of highly pure, dense, and uniform FCC single-phase (Fm3m crystal structure) (Hf-Ti-Ta-Zr-Nb)C high-entropy carbide using a milling time of 60 min and a sintering temperature of 1,600oC.

Aluminum-based powders have attracted attention as key materials for 3D printing owing to their low density, high specific strength, high corrosion resistance, and formability. This study describes the effects of TiC addition on the microstructure of the A6013 alloy. The alloy powder was successfully prepared by gas atomization and further densified using an extrusion process. We have carried out energy dispersive X-ray spectrometry (EDS) and electron backscatter diffraction (EBSD) using scanning electron microscopy (SEM) in order to investigate the effect of TiC addition on the microstructure and texture evolution of the A6013 alloy. The atomized A6013-xTiC alloy powder is fine and spherical, with an initial powder size distribution of approximately 73 μm which decreases to 12.5, 13.9, 10.8, and 10.0 μm with increments in the amount of TiC.

Conventionally, metal materials are produced by subtractive manufacturing followed by melting. However, there has been an increasing interest in additive manufacturing, especially metal 3D printing technology, which is relatively inexpensive because of the absence of complicated processing steps. In this study, we focus on the effect of varying powder size on the synthesis quality, and suggest optimum process conditions for the preparation of AlCrFeNi high-entropy alloy powder. The SEM image of the as-fabricated specimens show countless, fine, as-synthesized powders. Furthermore, we have examined the phase and microstructure before and after 3D printing, and found that there are no noticeable changes in the phase or microstructure. However, it was determined that the larger the powder size, the better the Vickers hardness of the material. This study sheds light on the optimization of process conditions in the metal 3D printing field.

The quality characteristics and antioxidant activity of Tteokbokkidduk alone or supplemented with 3%, 6%, 9%, and 12% wheat bran powder were assessed, to increase use of the wheat bran by-product of wheat milling. The moisture content, pH, and starch elution of Tteokbokkidduk increased with increasing wheat bran powder, while the water absorption rate did not. The L color value decreased and the a and b values increased with increasing wheat bran powder. Scanning electron microscopy of Tteokbokkidduk prepared with 0% and 3% wheat bran powder revealed uniform pore size distribution. In terms of texture profile analysis, hardness and chewiness increased, while cohesiveness decreased with increased content of wheat bran powder. Acceptance was highest for samples with 6% wheat bran powder. Quantitative description analysis (QDA) revealed increased brownness, roughness, nutty, bitterness, astringency, savory character, and hardness, and decreased adhesiveness, springiness, and chewiness with increased wheat bran powder. Principal component analysis (PCA) revealed highest overall acceptance of samples prepared with 6% wheat bran powder, reflecting the relatively low values of detrimental sensory characteristics. Antioxidant activities of Tteokbokkidduk increased as wheat bran powder content increased. The addition of 6% wheat bran powder resulted in excellent Tteokbokki in terms of acceptance, quality, and antioxidant activity.

The issue surrounding the problem of air pollution arising from rapid industrialization is one that is being continuously raised for discussion among the public, and concerns about indoor air quality have emerged both at home and abroad due to the longer periods of time spent indoors in modern times. Various studies are being conducted to solve this problem, and photocatalysts are also being studied as a solution. Accordingly, this research sought to verify the performance of reducing indoor pollutants by applying photocatalysts to building materials. As a result of evaluating the indoor pollutant reduction performance, it was confirmed that acetaldehyde was reduced by about 31%, toluene 29%, and total volatile compounds by 11%, and adhesion strength, an important factor regarding finishing material, was also enhanced 1.3 times or more based on Korean Industrial Standards. From these results, it is believed that indoor air pollution can be lowered to a certain extent through building materials using photocatalysts, and, therefore, research on long-term performance verification and evaluation methods should be continuously conducted and pursued in the future in relation to photocatalysts.

This study investigated the quality characteristics and antioxidant activity of Yanggaeng prepared with various amounts of watermelon radish flesh (WRF) powder, in ratios of 0 (control), 2.5, 5, 7.5, and 10% of the cooked white bean paste. The proximate composition, pH, sugar content, Hunter’s color values, texture analysis, and antioxidative activities of Yanggaeng were examined. Increasing the amount of WRF in the Yanggaeng tended to increase the crude ash, carbohydrate, sugar, total polyphenol, total flavonoids, and anthocyanin contents, a value, DPPH and ABTS radical scavenging activities, with decreasing the moisture and crude protein contents, L and b values, and pH. Texture measurement scores in terms of springiness, chewiness for Yanggaeng showed that 2.5% or 5.0% group was higher than those of the control group. Hardness was higher in the sample groups than in the control group. In conclusion, the results show that Yanggaeng with up to 7.0% added WRF powder can be developed as products, and there is a possibility of developing health functional snack products using WRF powder.

In this study, Korean Hallabong produced in Jeju Island and coffee were grafted to prepare coffee containing Hallabong extract and the nutritional components were analyzed. As the amount of Hallabong extract increased, the water content and total polyphenol content increased. However, the crude flour, crude protein, and total flavonoid content decreased significantly. The selenium content per 100 g was 91.28 mg in the 1% Hallabong group, and the iron content was 6.84 mg in the 3% Hallabong group. As the content of Hallabong extract in coffee increased, the L-value (brightness) and b-value (yellowness) increased, but the a-value (redness) showed a tendency to decrease. In the case of DPPH(2,2-Diphenyl-1-picrylhydrazyl) radical scavenging activity, the group containing 9% of Hallabong extract showed the highest value at 47.20 μmol/g of TEAC. In particular, the ABTS(2,2’-Azino-bis(3-ethylbenzothiazoline- 6-sulfonate)) and DPPH radical scavenging activity were significantly increased from coffee powder containing 6% or more of Hallabong extract(p<0.05). The caffeine content decreased as the amount of Hallabong extract added to coffee increased. Therefore, when making powder coffee with Hallabong extract added, it is recommended to set the content of Hallabong extract to 6%.

Smart materials capable of changing their characteristics in response to stimuli such as light, heat, pH, and electric and magnetic fields are promising for application to flexible electronics, soft robotics, and biomedicine. Compared with conventional rigid materials, these materials are typically composed of soft materials that improve the biocompatibility and allow for large and dynamic deformations in response to external environmental stimuli. Among them, smart magnetic materials are attracting immense attention owing to their fast response, remote actuation, and wide penetration range under various conditions. In this review, we report the material design and fabrication of smart magnetic materials. Furthermore, we focus on recent advances in their typical applications, namely, soft magnetic actuators, sensors for self-assembly, object manipulation, shape transformation, multimodal robot actuation, and tactile sensing.

Cobalt (Co) is mainly used to prepare cathode materials for lithium-ion batteries (LIBs) and binder metals for WC-Co hard metals. Developing an effective method for recovering Co from WC-Co waste sludge is of immense significance. In this study, Co is extracted from waste cemented carbide soft scrap via mechanochemical milling. The leaching ratio of Co reaches approximately 93%, and the leached solution, from which impurities except nickel are removed by pH titration, exhibits a purity of approximately 97%. The titrated aqueous Co salts are precipitated using oxalic acid and hydroxide precipitation, and the effects of the precipitating agent (oxalic acid and hydroxide) on the cobalt microstructure are investigated. It is confirmed that the type of Co compound and the crystal growth direction change according to the precipitation method, both of which affect the microstructure of the cobalt powders. This novel mechanochemical process is of significant importance for the recovery of Co from waste WC-Co hard metal. The recycled Co can be applied as a cemented carbide binder or a cathode material for lithium secondary batteries.

The process optimization of directed energy deposition (DED) has become imperative in the manufacture of reliable products. However, an energy-density-based approach without a sufficient powder feed rate hinders the attainment of an appropriate processing window for DED-processed materials. Optimizing the processing of DEDprocessed Ti-6Al- 4V alloys using energy per unit area (Eeff) and powder deposition density (PDDeff) as parameters helps overcome this problem in the present work. The experimental results show a lack of fusion, complete melting, and overmelting regions, which can be differentiated using energy per unit mass as a measure. Moreover, the optimized processing window (Eeff = 44~47 J/mm2 and PDDeff = 0.002~0.0025 g/mm2) is located within the complete melting region. This result shows that the Eeff and PDDeff-based processing optimization methodology is effective for estimating the properties of DED-processed materials.

A new Fe-Cr-Mo-B-C amorphous alloy is designed, which offers high mechanical strength, corrosion resistance as well as high glass-forming ability and its gas-atomized amorphous powder is deposited on an ASTM A213-T91 steel substrate using the high-velocity oxygen fuel (HVOF) process. The hybrid coating layer, consisting of nanocrystalline and amorphous phases, exhibits strong bonding features with the substrate, without revealing significant pore formation. By the coating process, it is possible to obtain a dense structure in which pores are hardly observed not only inside the coating layer but also at the interface between the coating layer and the substrate. The coating layer exhibits good adhesive strength as well as good wear resistance, making it suitable for coating layers for biomass applications.

본 연구는 흰점박이꽃무지 유충 분말의 첨가량에 따른 닭 가슴살 소시지의 품질특성에 대한 영향을 분석하였다. 분석 결과 흰점박이꽃무지 유충 분말 첨가 유화형 닭고기 소시지와 첨가하지 않은 대조구 간의 일반성분 차이는 보이지 않았다(p>0.05). 흰점박이꽃무지 유충 분말 첨가량에 따라 명도는 감소하고 황색도는 증가하는 경향을 보였으며, 흰점박이꽃무지 유충 분말의 높은 pH가 육제품의 pH를 상승시켜 가열감량은 감소시키고 보수력은 증가시키는 긍정적인 영향 을 보였다. 유화형 소시지의 물성 중 경도에서 흰점박이꽃 무지 유충 분말 첨가구가 대조구 보다 높은 값을 나타내 조직감에 변화를 주었으며, 자유라디칼 활성도와 총 페놀 함량은 흰점박이꽃무지 유충 분말의 첨가량에 따라 증가하는 경향을 보였다. 이러한 결과를 통해 흰점박이꽃무지 유충 분말의 우수한 항산화 활성이 육제품에서도 발현이 가능 하며 기능성 첨가물로서 흰점박이꽃무지 유충 분말을 활용 한 기능성 소시지 제조 또한 가능할 것으로 판단된다.