This study is to manufacture a titanium dioxide (TiO2) photocatalyst by recycling sludge generated using titanium tetrachloride (TiCl4) as a coagulant. Compared to general sewage, a TiCl4 coagulant was applied to dyeing wastewater containing a large amount of non-degradable organic compounds to evaluate its performance. Then the generated sludge was dried and fired to prepare a photocatalyst (TFS). Scanning electron microscope-energy dispersive X-ray spectroscopy (SEM-EDX), X-ray diffraction (XRD), and nitrogen oxide reduction experiments were conducted to analyze the surface properties and evaluate the photoactive ability of the prepared TFS. After using titanium tetrachloride (TiCl4) as a coagulant in the dyeing wastewater, the water quality characteristics were measured at 84 mg/L of chemical oxygen demand (COD), 10 mg/L of T-N, and 0.9 mg/L of T-P to satisfy the discharge water quality standards. The surface properties of the TFS were investigated and the anatase crystal structure was observed. It was confirmed that the ratio of Ti and O, the main components of TiO2, accounted for more than 90 %. As a result of the nitric oxide (NO) reduction experiment, 1.56 uMol of NO was reduced to confirm a removal rate of 20.60 %. This is judged to be a photocatalytic performance similar to that of the existing P-25. Therefore, by applying TiCl4 to the dyeing wastewater, it is possible to solve the problems of the existing coagulant and to reduce the amount of carbon dioxide generated, using an eco-friendly sludge treatment method. In addition, it is believed that environmental and economic advantages can be obtained by manufacturing TiO2 at an eco-friendly and lower cost than before.

This study compares the characteristics of a compact TiO2 (c-TiO2) powdery film, which is used as the electron transport layer (ETL) of perovskite solar cells, based on the manufacturing method. Additionally, its efficiency is measured by applying it to a carbon electrode solar cell. Spin-coating and spray methods are compared, and spraybased c-TiO2 exhibits superior optical properties. Furthermore, surface analysis by scanning electron microscopy (SEM) and atomic force microscopy (AFM) exhibits the excellent surface properties of spray-based TiO2. The photoelectric conversion efficiency (PCE) is 14.31% when applied to planar perovskite solar cells based on metal electrodes. Finally, carbon nanotube (CNT) film electrode-based solar cells exhibits a 76% PCE compared with that of metal electrodebased solar cells, providing the possibility of commercialization.

PURPOSES : This study analyzes the characteristics of nitrogen oxide concentration by applying titanium dioxide to existing roads in urban areas, using correlation analysis and a generalized linear model. METHODS : To analyze the characteristics of nitrogen oxide concentration with/without applying titanium dioxide to the urban road segment, data acquisition was conducted for nitrogen oxide concentration, weather information, and traffic information, etc., and a correlation analysis was conducted for each factor, with/without applying titanium dioxide to the roads. In addition, nitrogen oxide concentration generation models with/without the application of titanium dioxide to the roads were estimated using a generalized linear model. RESULTS : The results demonstrate that relative humidity and temperature were found to be slightly correlated with the nitrogen oxide concentration, both with and without the application of titanium dioxide to the roads; however, wind speed, solar radiation, and traffic volume were found to have somewhat low correlation according to the results of a correlation analysis. Moreover, relative humidity, temperature, solar radiation, and traffic volume were significant when titanium dioxide was applied to the roads, based on the estimated model from a generalized linear model, and the wind speed, solar radiation, and traffic volume were significant for the absence of titanium dioxide on the roads. CONCLUSIONS : Analytical results indicated that the characteristics of nitrogen oxide concentration vary depending on the application of titanium dioxide to the roads. In particular, when titanium dioxide was applied to the roads, the relative humidity and temperature were analyzed; according to both analyses, i.e., correlation analysis and a generalized linear model, the nitrogen oxide concentration was affected.

Carbon supports for dispersed platinum (Pt) electrocatalysts in direct methanol fuel cells (DMFCs) are being continuously developed to improve electrochemical performance and catalyst stability. However, carbon supports still require solutions to reduce costs and improve catalyst efficiency. In this study, we prepare well-dispersed Pt electrocatalysts by introducing titanium dioxide (TiO2) into biomass based nitrogen-doped carbon supports. In order to obtain optimized electrochemical performance, different amounts of TiO2 component are controlled by three types (Pt/TNC-2 wt%, Pt/TNC-4 wt%, and Pt/TNC-6 wt%). Especially, the anodic current density of Pt/TNC-4 wt% is 707.0 mA g−1 pt, which is about 1.65 times higher than that of commercial Pt/C (429.1 mA g−1 pt); Pt/TNC-4wt% also exhibits excellent catalytic stability, with a retention rate of 91 %. This novel support provides electrochemical performance improvement including several advantages of improved anodic current density and catalyst stability due to the well-dispersed Pt nanoparticles on the support by the introduction of TiO2 component and nitrogen doping in carbon. Therefore, Pt/TNC-4 wt% may be electrocatalyst a promising catalyst as an anode for high-performance DMFCs.

양친성 PCZ-r-PEG 랜덤 공중합체를 기반으로 한 수열합성법을 통해 자가조립된 메조기공 이산화티타늄 마이크로 스피어를 합성하였다. 중합된 PCZ-r-PEG는 푸리에 변환 적외분광법(fourier transform infrared spectroscopy, FT-IR), 핵자기 공명(nuclear magnetic resonance, NMR), 젤 투과 크로마토그래피(gel permeation chromatography, GPC) 그리고 투과전자 현미경(transmission electron microscopy, TEM)을 통해 그 특성이 분석되었다. 다공성 이산화티타늄 입자는 PCZ-r-PEG, 글루코스(glucose), 물을 테트라히드로푸란(tetrahydrofuran, THF) 용액에 분산시킨 뒤 150°C, 12시간 동안 반응시켰다. 다공성 이산화티타늄 입자의 구조와 결정성 분석을 위해 주사전자현미경(scanning electron microscopy, SEM)과 엑스선 회절(X-ray diffraction, XRD)이 사용되었다.

Titanium dioxide thin films were fabricated as hydrogen sensors and its sensing properties were tested. The titanium was deposited on a SiO2/Si substrate by the DC magnetron sputtering method and was oxidized at an optimized temperature of 850˚C in air. The titanium film originally had smooth surface morphology, but the film agglomerated to nano-size grains when the temperature reached oxidation temperature where it formed titanium oxide with a rutile structure. The oxide thin film formed by grains of tens of nanometers size also showed many short cracks and voids between the grains. The response to 1% hydrogen gas was ~2×106 at the optimum sensing temperature of 200˚C, and ~103 at room temperature. This extremely high sensitivity of the thin film to hydrogen was due partly to the porous structure of the nano-sized sensing particles. Other sensor properties were also examined.

Nanopowders of titanium dioxide incorporating the transition metal element(s) were synthesized by flame synthesis method. Single element among Fe(III), Cr(III), and Zn(II) was doped into the interior of crystal; bimetal doping of Fe and Zn was also made. The characteristics of transition-metal-doped nanopowders in the particle feature, crystallography and electronic structures were determined with various analytical tools. The chemical bond of Fe-O-Zn was confirmed to exist in the bimetal-doped nanopowders incorporating Fe-Zn. The transition element incorporated in the was attributed to affect both Ti 3d orbital and O 2p orbital by NEXAFS measurement. The bimetal-doped nanopowder showed light absorption over more wide wavelength range than the single-doped nanopowders

Cosmetic industries have recently developed sun-block products, which are composed of W/O or O/W emulsion system. It was very difficult for waterproofing product to show the stability in W/O emulsion with TiO2. To enhance the stability of W/O emulsion, it needs to be combined with the water and oil soluble components as the gelling agents. The emulsifiers used in W/O were 3.0% of cetyl dimethicone copolyol, 2.0% of sorbitan sesquioleate as the basic emulsifiers, and 0.6% of quaternium-18 bentonite and 1.5% of dextrin palmitate as stabilizer were used. The content of titanium dioxide was optimized up to 8.0%. Titanium dioxide was used as the UV scattering powder coated with Al2O3(UV-sperse T40/TN). The sunscreen cream prepared with W/O emulsion system by using QB and DP showed higher stability than that of W/O emulsion system by using each QB and DP. W/O emulsion from Formula 3 for passing one year was very durable more than F1 and F2. Within W/O emulsion by observing F1, F2 and F3 for one year, F3 was more excellent than F2 and F3 when they were observed at RT, 4℃, 40℃, because F3 used the mixed QB and DP in W/O emulsion. The zeta potential for F1, F2, and F3 after one year were 21, 30 and 43, respectively. From these result F3 was found best stable emulsion. The in-vitro SPF value for F3 was 35 for the initial product at room temperature and also, the in-vitro SPF values of F3 was 32 for after one year. Finally, the mean in-vivo SPF value of 10 volunteers for F3 was 27.3 by the Korea cosmetic association made the rules of SPF.