냉매 오충전은 에어컨에서 빈번하게 발생하는 고장 모드 중 하나로, 적정 충전량 대비 부족 및 과충전 모두 냉방 성능의 저하를 유 발하므로 충전된 냉매량을 정확하게 판단하는 것이 중요하다. 본 연구에서는 퍼지 군집화 기법을 통한 정상상태 식별을 통해 냉매 오 충전량을 다중 분류하는 모델을 개발하였다. 정상상태 식별을 위해 에어컨 운전 데이터에 대해 이동 평균 간의 차이를 활용한 퍼지 군 집화 알고리즘을 적용하였으며, IFDR를 통해 기존 연구된 정상상태 판단 기법들과 식별 결과를 비교하였다. 이후, 시스템 내 상관성 을 고려한 mRMR을 이용해 특징을 선택하였으며, 도출된 특징을 이용해 SVM 기반의 다중 분류 모델이 생성되었다. 제안된 방법은 시험 데이터를 통해 만족할 만한 분류 정확도와 강건성을 도출하였다.

This research studied faults that may occur during slow charging using the J1772 adapter of Tesla Model-3 electric vehicles. When the AC terminal was instantaneously disconnected, charging was performed normally when an AC circuit with disconnection up to three disconnection times was connected. Charging control was suspended when the number of disconnection reached four times. However, if the AC disconnection time exceeded 22 seconds, the charging control was stopped regardless of the number of disconnection. When a contact failure occurred at the AC terminal, high surge current and noise occurred. However, when the contact improved, the charging control continued. In terms of safety, it seems necessary to take measures such as stopping charging control when detecting noise.

When the CP voltage is disconnected, the measured voltage on the ICCB side is measured to be 12V, and the voltage on the OBC side is measured to be 0V. When the PD signal was disconnected, the ICCB-side measured voltage was 0V and the OBC-side measured voltage was 4.5V. From this, disconnected position be found with the voltage value measured. When CP was disconnected for a short time, the PD voltage did not change to 1.5V, and when the PD was disconnected, the CP signal and PD signal changed to 9V, and if the CP and PD voltages were normal, the charge control could be performed normally.

In this study, we propose a new truss deckplate system, which does not require temporary floor supports during construction, with ultra-high-performance concrete (UHPC) infilled top bars. The increased stiffness and strength of the proposed system were well retained as compared to those of the existing truss deckplate systems, thereby resulting in the reduction of maximum deflection at the span center. Four-point bending tests were performed on five specimens with a net span of 4.6 m to evaluate the structural performance of proposed system in the construction stage. In addition, the load-deflection curve was plotted for each specimen, and the effects of test parameters were analyzed. Further, a rigorous nonlinear three-dimensional finite element analysis was performed, and its results were compared with the test results. From the results, it was observed that the test specimens of the proposed system exhibited superior performance as compared to those of the existing one and also satisfied the serviceability requirement during construction provided by the Korea Building Code 2016.

Numerical models of composite floor systems with various thickness of phase change material and sizes of circular spacers were developed based on finite element analysis. In order to perform a heat transfer analysis, thermal properties of steels were determined and those of phase change material were estimated from experiment results. In addition, the thermal insulation performance of composite floor systems with respect to different thickness of phase change material and sizes of circular spacers was predicted. To verify the validity of analysis, analysis results were compared with vertical furnace fire test results of equivalent conditions. As a result, available thicknesses of phase change material and sizes of circular spacers were proposed to satisfy the thermal insulation criteria of Korean Standards.

Hydrogen energy is expanding in range for civil use together with development of pollution-free power sources recently, and it is judged that the use of hydrogen will increase more as a part of carbon dioxide reduction measures according to the Climatic Change Convention. Especially, it is thought that the securement of safety of the used dispenser will be the biggest obstacle in the use of high-pressure hydrogen because the hydrogen station is operated in a high pressure. This study found risks in the process and problems on operation by making use of HAZOP(6 kinds), a qualitative safety evaluation technique, and FMEA(5 kinds), a fault mode effect analysis, for the hydrogen charging system at a hydrogen gas station, derived 6 risk factors from HAZOP and 5 risk factors from FMEA, and prepared measures for it.

대체연료 충전을 위한 기반시설의 효율적 설계 및 개발은 신에너지 경제의 촉진을 위해 필요하다. 본 논문은 GIS와 입지모델을 결합하여 공간의사결정지원 시스템(SDSS)의 원형을 개발하였다. 사용된 입지 모델은 일회 주유에 따른 주행거리가 제한적인 대체연료 차량을 대상으로 최대의 충전 서비스를 제공할 수 있는 지점에 충전소를 입지하며, 이때 운전자는 주유를 위해 기-종점 간의 최적경로에서 벗어나 우회할 수도 있다고 가정한다. 개발된 SDSS는 확장가능할 뿐 아니라 의사결정자가 다양한 수요 시나리오를 탐색할 수 있다. 이를 통해 대체연료차 운전자의 우회 행태, 시장 수요의 공간적 분포, 주행거리, 기존 시설물에 관한 상이한 가설을 세우고 그 결과를 실험할 수 있다. 주어진 조건을 만족하는 최선의 충전소 위치에 관한 결과는 지도 및 통계와 같은 다양한 산출물로 보고된다.

전기자동차의 상용화시대에 대비한 전기자동차 충전네트워크가 시급해지고 있다. 해외에서는 주차장에 PV시스템을 설치하여 얻어진 전력으로 전기자동차 충전을 할 수 있는 전기자동차 충전소가 설치되어지고 있다. 또한 우리나라에서도 충전인프라 구축방안 및 전기자동차 충전시설 지원기준 등을 설정하여 제시하고 있지만 해외처럼 PV시스템을 이용한 전기자동차 충전소의 사례가 국내에는 없으며, 일반전력을 이용한 전기자동차 충전소만 제시하고 있다. 따라서 본 논문에서는 국내의 전기자동차 충전네트워크 구축에 대비하여 국내 외 태양광 주차장과 해외 PV시스템 전기자동차 충전소의 사례를 조사하여 구조시스템, 구조 재료 등을 분석하여 비교 분석한 결과, 해외 PV시스템 전기자동차 충전소의 경우 캔틸레버 구조와 소규모 타입이 많이 설치되었다.

This paper presents a study on the construction method of modular pier system using CFTs. Modular Pier System consist of various prefabricated modules and is constructed by assembling components. Research scop include development of standard modules for adjustable to various height, connection between modules, and test bed construction. For the evaluation of this systems’s performance, Many numerical and experimental studies were conducted. In this study, we develop rapid construction system for site application of modular pier.

The docking and recharging system for a mobile robot must guarantee the ability of the mobile robot to perform its tasks continuously without human intervention. In this paper, two docking mechanisms are proposed with localization error-compensation capability for the auto recharging system. Friction forces or magnetic forces are used between the docking parts of the docking module and those of the docking station. In addition, an auto recharging system is developed to control the power. Since the system is modularized, it can easily be adapted to other robots.