항만 내 선박과 부두의 사고를 예방하기 위하여 통항 및 접안 안전성 평가를 통하여 안전한 부두가 건설되어 관리하고 있으나, 선 박의 접안 및 계류 과정에서 선박이 부두에 충돌하거나 로프로 인한 인명사고의 발생 등 예측할 수 없는 사고들이 종종 발생한다. 자동계류장 치는 선박의 신속하고 안전한 계류를 위한 자동화된 시스템으로 로봇 매니퓰레이터와 흡착 패드로 구성된 탈/부착 메커니즘을 가지고 있다. 본 논문은 자동계류장치의 흡착 패드의 위치 및 속도제어에 필요한 선체와의 변위 및 속도 측정 시스템을 다룬다. 자동계류장치에 적합한 측 정 시스템을 설계하기 위하여, 본 논문은 우선 센서의 성능 및 실외 환경적 특성 분석을 수행한다. 다음으로 이러한 분석 결과를 토대로 실외 부두환경에서 설치되는 자동계류장치에 적합한 변위 및 속도 측정시스템의 구성 및 설계 방법에 대해 기술한다. 또한 센서의 측정상태 감지 및 속도 추정을 위한 알고리즘을 제시한다. 제안된 방법은 다양한 속도 구간에서의 변위 및 속도 측정 실험을 통해 그 유용성을 검증한다.

The air dilution olfactory method to measure complex odors needs to store and carry odor samples from the field sampling until the analysis in laboratories. Until the analysis of sample in the laboratory, odor dilution factor (odor sensitivity) in the sample bag may decrease over time depending on the characteristics of each odor substances. This is one of the limitation for the air dilution olfactory method. Thus, the air dilution device enable to measure without loss in complex odors of samples. Recently, many studies on the performance test of on-site air dilution devices, i.e., field olfactometer, has been conducted to figure out the feasibility of the field olfactometers. In this study, seven odor samples were collected from five odor emission source sites. And comparative analysis with the air dilution olfactory method was carried out to assess the field applicability of the olfactometer. As results, the performance of the field olfactometer used in this study is regared as the affordable method. The dilution factors from between two methods showed the similar values, indicating low values of standard deviations. In order to ensure the accuracy and precision of measurement data using the field olfactometer, methodology minimized variables (that may affect measurement) needs to establish.

A universal joint is a device that transmits the power of a combat vehicle engine to a cooling fan. The power of the engine is transmitted to the universal joint as it is without buffering, and play occurs at the joint between the drive shaft connected to the engine and the driven shaft connected to the cooling fan according to the usage time. Accordingly, the universal joint is periodically replaced, and the criterion for this is the degree of torsion of the universal joint. However, if the universal joint is not properly maintained during the replacement cycle, damage to the universal joint as well as damage to the surrounding power supply may occur. Accordingly, a backlash measuring device was developed to determine the limit of durability of the universal joint, and the limit of durability was derived through regression analysis of the backlash value according to the use time obtained from the accelerated life test.

Aluminum nitride having a dense hexagonal structure is used as a high-temperature material because of its excellent heat resistance and high mechanical strength; its excellent piezoelectric properties are also attracting attention. The structure and residual stress of AlN thin films formed on glass substrate using TFT sputtering system are examined by XRD. The deposition conditions are nitrogen gas pressures of 1 × 102, 6 × 103, and 3 × 103, substrate temperature of 523 K, and sputtering time of 120 min. The structure of the AlN thin film is columnar, having a c-axis, i.e., a <00·1> orientation, which is the normal direction of the glass substrate. An X-ray stress measurement method for crystalline thin films with orientation properties such as columnar structure is proposed and applied to the residual stress measurement of AlN thin films with orientation <00·1>. Strength of diffraction lines other than 00·2 diffraction is very weak. As a result of stress measurement using AlN powder sample as a comparative standard sample, tensile residual stress is obtained when the nitrogen gas pressure is low, but the gas pressure increases as the residual stress is shifts toward compression. At low gas pressure, the unit cell expands due to the incorporation of excess nitrogen atoms.

This study develops a new device system for measuring a slope of object with non-adhesive, non-contact and non-face-to-face, namely Inclinometer Slope Laser Measuring (ISLM), that is applicable in the field. This system includes cradle, laser, camera, and computer and the filming and is performed after laser projection at programmed intervals. After measuring the amount of displacement converted to numerical values, these values can then be transferred to the office using the selected data transmission method. The obtained results from the test carried out to verify the reliability of the ISLM system indicated that the ISLM system can measure with accurately level of 0.1mm/Pixel at 1m distance and when increasing the camera resolution, the precision might increase proportionally. Therefore, the proposed measure system may widely apply on-site for various constructions, especially, in the case of object with very high surface temperature where exhibits difficulty to directly measure the adjacent structures. However, due to the sensitive reaction to the illuminance, this method can be applied with caution at times of large changes in illuminance, such as at dawn and at dusk.

엔진의 출력을 측정하기 위한 방법은 실린더의 연소압력을 측정하여 지시마력을 구하는 방법과 축토크를 측정하여 축마력을 구하는 방법이 있다. 축토크로 실린더의 상태를 확인하기에는 한계가 있으며, 엔진의 성능 측정과 실린더의 연소 해석을 위해서는 실린더 의 연소 상태를 확인할 수 있는 연소압력을 측정하는 방법이 가장 정확하다. 측정에 있어 연소압력은 크랭크샤프트 회전 각도에 따른 실린더 압력이 도시되어야하기 때문에 정확한 실린더 앵글각도를 정확히 인지시키는 작업이 가장 중요하다. 본 연구에서는 실제 운항선의 발전기 엔진을 대상으로 실린더 압력을 측정하기 위하여 크랭크 앵글 센서로 엔코더를 사용하였고 엔코더에서 인지하는 TDC(TDCencoder)와 압축압력에 의한 TDC(TDCcomp) 간의 실측을 통하여 차이가 발생하는 원인에 대하여 고찰하였다. 또한 0 %, 25 %, 50 %와 60 % 부하에서 측 정된 실린더의 TDCcomp와 TDCencoder 간의 차이를 통하여 크랭크샤프트의 제작에 의한 영향, 부하증가에 따른 엔진과 발전기 사이의 커플링 영향에 대한 결과를 고찰하였으며, 발전기의 부하가 증가할수록 최대 3°CA까지 TDC의 오차가 발생함을 확인하였다.

본 실험은 토마토(Solanum lycopersicum L. ‘Hoyong’ ‘Super Doterang’) 암면재배에서 배지 전체의 정전용량을 측정할 수 있는 장치(Substrate capacitance measurement device, SCMD)를 기반으로 한 적정 급액 방법을 구명하기 위하여 누적일사량 제어구(Integrated solar radiation automated irrigation, ISR)와 물관수액흐름 제어구(sap flow automated irrigation, SF)를 대조구로 비교하면서 봄부터 여름철과 겨울철에 재배를 실시하였다. SCMD 제어구는 급액 개시 후 배지 한 개당 설정된 배액 목표량이 처음 발생하는 시점까지 10분간격으로 급액하였고 첫 배액이 배출되면 그 때의 배지의 정전용량(Capacitance)을 100%로 간주하고 그 기준치의 급액제어 점(Capacitance threshold, CT)에 도달하면 급액 되었고 그 뒤 목표 배액량이 발생하면 급액이 멈추는 방식으로 제어되었다. 봄부터 여름재배에서 실험 처리를 위해 SCMD제어구의 일회 급액량 (Irrigation volume per event)을 50, 75, 또는 100mL로 설정하였고 겨울철 재배에서는 CT가 0.65, 0.75, 또는 0.90가 되면 급액 되도록 설정하였다. 봄부터 여름철 재배에서 일회 급액량을 50, 75, 100mL로 설정하였을 때 급액 횟수는 각각 39, 29, 19회 였고 배액율은 각각 3.04, 9.25, 20.18%였다. 겨울철 재 배에서 CT를 0.65, 0.75, 0.90로 설정하였을 때 급액횟수는 각각 5.67, 6.50, 14.67회였고 배액율은 9.91, 10.78, 35.3%였다. 봄부터 여름철 재배에서 일회 급액량 처리에 따른 물관수액흐름속도(SF) 변화는 1회 급액량과 배액량을 각각 50과 75mL로 제한한 경우 100mL로 제 한한 경우와 비교하여SF 신호가 외부 광량 신호 (SI) 보다 늦어지는 경향(time lag)을 보였고 겨울철 재배에서 CT를 0.65로 설정한 경우는 물관수액흐름 속도나 함수율이 매우 낮아졌고 CT를 0.90로 설정한 경우는 함수율과 물관수액흐름 속도는 매우 높았으나 많은 배액이 배출되었다. 따라서 토마토 봄부터 여름철 재배에서 SCMD를 활용하여 CT를 0.9로, 배지 한 개당 배액 목 표량을 100mL로 설정하였을 때 일회 급액량은 75~100mL 범위가 적합하고 겨울철 재배에서는 1회 급 액량을 75mL로, 배액 목표량을 70mL로 설정하였을 때 CT는 0.75이상 0.9이하 범위가 적합할 것으로 판단되었다. 앞으로 정전용량 값과 배지 용적수분함량의 관계성을 구명하고 보정계수를 구하는 연구가 필요할 것으로 판단된다.

This study was designed to examine the performance of an aspirated radiation shield(ARS), which was made at the investigator's lab and characterized by relatively easier making and lower costs based on survey data and reports on errors in its measurements of temperature and relative humidity. The findings were summarized as follows: the ARS and the Jinju weather station made measurements and recorded the range of maximum, average, and minimum temperature at 2.0~34.1oC, -6.1~22.2oC, –14.0~15.1oC and 0.4~31.5oC, -5.8~22.0oC, -14.1~16.3oC, respectively. There were no big differences in temperature measurements between the two institutions except that the lowest and highest point of maximum temperature was higher on the campus by 1.6oC and 2.6oC, respectively. The measurements of ARS were tested against those of a standard thermometer. The results show that the temperature measured by ARS was lower by –2.0oC or higher by 1.8oC than the temperature measured by a standard thermometer. The analysis results of its correlations with a standard thermometer reveal that the coefficient of determination was 0.99. Temperature was compared between fans and no fans, and the results show that maximum, average, and minimum temperature was higher overall with no fans by 0.5~7.6oC, 0.3~4.6oC and 0.5~3.9oC, respectively. The daily average relative humidity measurements were compared between ARS and the weather station of Jinju, and the results show that the measurements of ARS were a little bit higher than those of the Jinju weather station. The measurements on June 27, July 26 and 29, and August 20 were relatively higher by 5.7%, 5.2%, 9.1%, and 5.8%, respectively, but differences in the monthly average between the two institutions were trivial at 2.0~3.0%. Relative humidity was in the range of –3.98~+7.78% overall based on measurements with ARS and Assman's psychometer. The study analyzed correlations in relative humidity between the measurements of the Jinju weather station and those of Assman's psychometer and found high correlations between them with the coefficient of determination at 0.94 and 0.97, respectively.

This study is a development of measuring instrument capable of measuring the temperature measurement at a temperature of between 0 ℃ and 1600 ℃ at a high temperature of the high temperature. This development technique develops a measuring device capable of measuring two different temperature measurements by combining two different temperature measurements ranging from one measurement module to the hot temperature to the high temperature. Also, it develops in a vacuum or high pressure state.

Euglena agilis의 운동성 반응을 자동으로 측정하는 장치 인 E. agilis 시스템 (E-Tox)을 이용하여 8종의 중금속 (Ag, Cd, Cr(VI), Cu, Hg, Ni, Pb, Zn)에 대한 독성시험을 실시하 였다. E. agilis 운동성 시험 (biomonitoring test)으로부터 도 출된 EC50과 문헌상의 자료 조사로 얻은 기존 생태독성 시 험 생물 종들(D. magna, V. fischeri, 그리고 E. gracilis)의 EC50을 비교하여 시험물질에 대한 E. agilis의 독성 민감도 를 평가하였다. 또한 축산폐수 방류수, 도금폐수 방류수, 도 금폐수 1차 처리 시료에 대해 D. magna 급성 독성시험과 E. agilis 운동성 반응 시험을 수행 후 TU를 비교하여 E. agilis 운동성 시험의 현장 적용 가능성을 평가하였다. E. agilis는 시험 중금속에 대해 D. magna보다 독성민감도가 전반적으 로 낮았으나 V. fischeri 또는 E. gracilis와 유사하거나 좀 더 민감하였다. E. agilis는 D. magna test로 유독성으로 판명된 도금폐수 1차 처리수에 대해 신속한 독성반응을 나타내었 다. E-Tox 시스템은 기존의 생태독성시험장비에 비해 빠르 고 작동이 간편한 자동화 기기라는 장점이 있다. 본 연구의 결과 E-Tox 시스템을 이용한 E. agilis 운동성 시험은 향후 독성폐수에 대한 조기경보를 위한 생태독성시험법으로 적용 될 수 있을 것으로 판단된다.

The measuring equipment capable of thermo measuring of wide range thermo range(0℃ ~ 160 0℃) will be developed in a high temperature and high pressure state. The developed technology is a combination of one measuring two different temperatures measured in the measuring to a high temperature as possible at a low temperature from thermocouple module(thermocouple) to develop an integrated measuring device capable of measuring the broadband. Also, to develop two or more guard module to ensure the water-tightness and durability of the device to develop in a vacuum or high pressure is applied to the one-piece measuring device.

In this study, an acceleration sensor that has optical fibers to measure the inclination and acceleration of a structure through contradictory changes in two-component FBG sensors was examined. The proposed method was to ensure precise measurement through the unification of the deformation rate sensor and the angular displacement sensor. A high sensitivity three-axis accelerometer was designed and prepared using this method. To verify the accuracy of the accelerometer, the change in wavelength according to temperature and tension was tested. Then, the change in wavelength of the prepared accelerometer according to the sensor angle, and that of the sensor according to the change in ambient temperature were measured. According to the test results on the FBG-based vibration sensor that was developed using a high-speed vibrator, the range in measurement was 0.7 g or more, wavelength sensitivity, 2150 pm/g or more, and the change in wavelength change, 9.5 pm/℃.