In this study, experiments and simulations were performed for fillet joint friction stir welding according to tool shape and welding conditions. Conventional butt friction stir welding has good weldability because heat is generated by friction with the bottom of the tool shoulder. However, in the case of fillet friction stir welding, the frictional heat is not sufficiently generated at the bottom of the tool shoulder due to the shape of the tool and the shape of the joint. Therefore, it is important to sufficiently generate frictional heat by slowing the welding speed as compared to butt welding. In this study, experiments and simulations were carried out on an aluminum battery housing made by friction stir welding an extruded material with a fillet joint. The temperature of the structure was measured using a thermocouple during welding, and the heat source was calculated through correlation analysis. Thermal elasto-plastic analysis of the structure was carried out using the calculated heat source and geometric boundary conditions. It is confirmed that the experimental results and the simulation results are well matched. Based on the results of the study, the deformation of the structure can be calculated through simulation even if the tool shape and welding process conditions change.

In this paper, graphene-coated Al powders prepared by in situ reduction method were directly used for cold spraying, obtaining a graphene-reinforced Al matrix composite coating with more compact structure and better performance. Cross-sectional analysis revealed that compared with the pure Al powders, the graphene-coated Al powders were more severely deformed, and the resulting coating was denser and its porosity was reduced by over 80%. The hardness of the graphene-coated Al coating was increased by 40%, and its brine immersion time was prolonged by nearly three times. However, the graphene increases the pitting sensitivity of the Al coating; so, the enhanced corrosion resistance of the graphene-coated Al coating is mainly attributed to the improvement of its structure densification.

선박 및 해양구조물에서 사용하고 있는 고강도 알루미늄 합금들은 스틸과 비교해서 많은 이점을 가지고 있다. 최근 고강도 알루미늄 합금들은 육상 및 해양에 폭넓게 사용되고 있으며, 특히, 특수목적 선박의 선체 외판구조에 많이 이용되고 있고, 교량 구조물에 사용되는 상자 구조물, 그리고 고정식 해양플랫폼의 상부구조에서 소비율이 증가하고 있다. 알루미늄 재료는 스틸보다 1/3의 중량 구성비를 통하여, 구성 중량을 줄이게 하여 연비 절감을 가능하게 한다. 일반적인 강구조물의 응력-변형률 관계와 비교하면, 용접가공에 따라 발생하는 열영향부의 존재로 인하여 상당히 다르게 나타난다. 왜냐하면, 강구조물과 비교하면 열전도율이 높아서, 열영향부(heat affected zone, HAZ)가 남아 있어 구조 강도 저하를 가져온다. 본 논문에서는 MIG(Metal inert gas) 용접 때문에 발생하는 열영향부를 고려하고, 종방향 압축 하중에 대한 알루미늄 보강판의 좌굴 및 최종강도 특성을 분석하였다. MIG 용접에 따른 열영향부를 고려한 경우, 좌굴 및 최종강도 모두 감소하며, 열영향부의 범위가 15 mm부터 항복 이후 에너지 소실률이 크게 나타나며, 25 mm 이상부터는 그 차이가 크지 않다. 따라서, 알루미늄 합금재료를 적용한 보강판의 구조 거동을 파악하기 위해서는 열영향부 영향에 대한 검토 및 분석이 중요하다.

The objective of this study is to find the optimal production process in the aluminum IMS core parts. To reduce the production process, the total stage was designed at a total of 2 stages and 3 stages. In the total 2 stages process, the production stage was divided into a shaft part production and a yoke part production. In the total 3 stages process, the yoke production stages were subdivided into the 2 stages for distributing the stress. The results were compared and analyzed in terms of effective stress, folding characteristics and load characteristics. The stress distributions according to the production total stages were almost the same, the yoke production stage was received high stress due to the high strain. Both the tubular shaft yoke and solid shaft yoke according to the production total stages did not have any problems in the production because there did not occur the folding, metal flow and under-fill. When the total 2 stages were employed, the load for producing the tubular shaft yoke and the solid shaft yoke was decreased by 35.0% and 27.1%, respectively. As the results, when the total 2 stages process is applied rather than 3 stages process, the product is produced quickly and it is expected to be advantageous for the production cost due to the low load.

Defects in most structures can be generated not only on outside but also on inside or on the back-side during the manufacturing or construction process. Also they cause the growth of defects due to operation of various complex environments and structures will be destroyed eventually. In order to improve the reliability of the structure, the detection and size-estimation of defects should be investigated. In this paper, as an extension of previous studies on surface defects, two-dimensional artificial backside cracks (blind cracks) into paramagnetic material were evaluated by using the same aluminum probe. The potential drop at the defect position is distributed in the n-shape in the case of the back defect, which is different from results of the surface defect (u-shape). The potential drops at the defect position are measured with the largest value. The potential drop ratio (Vcmax/Vs) for the defective position is used as a parameter to predict the thickness (l) of defect position.

본 연구에서는 생체모방형 비대칭 분리막 제조방법인 사각펄스양극산화법의 비대칭성 한계를 극복하기 위해 최근 보고된 셀렌산 전해액을 이용하고 표면개질에 따른 정류특성을 평가하였다. 분리막의 비대칭 원뿔형 채널은 최소직경이 10 nm이고 최대직경이 50 nm이며 길이가 5 μm이었다. 분리막의 정류특성은 기존 황산 전해액에서 제작된 것보다 높았으며 +1 V에서의 전류가 -1 V일 때보다 최대 2.9배를 나타내었다. 또한, 실란화 반응을 이용한 표면개질을 통해 술폰산기를 도입한 분리막은 반대로 -1 V에서의 전류가 +1 V일 때보다 전류의 최대 4.2배인 정류특성을 나타냈다. 실험에 대한 이론적 증명은 2D 모델에 수치해석 결과를 제시함으로써 뒷받침되었다. 본 연구의 결과는 서로 다른 정류방향을 갖는 두 종류의 이온 정류 분리막을 손쉽게 제작할 수 있는 방법을 제시하며 이온의 이동을 제어하기 위한 다양한 연구 분야에 활용될 수 있을 것으로 기대된다.

With the current increase in national income, consumers are favoring expensive home appliances. Many aluminum parts are used to improve the appearance of TV products. However, many losses are incurred due to production defects. There are many flaws in the bending process. This study studied the improvement of bending defects during fault handling. The material used is an aluminum alloy (6063), and the product is a serrated component on the surface of an aluminum part. After the bending process, it was identified how the sawtooth area was twisted. Then, while bending, experimented to find the main cause of the defect. The study tried to find maximum effectiveness with a minimum experiment using 6 sigma techniques. The experiment showed that there were many defects depending on the bending speed of the part and the distance it was fixed. The experiment used a method of finding optimal conditions by combining variables from each item. As a result, the failure was minimized when the distance between the two axes was maintained at 4.5-5mm and the bending speed was maintained at 15mm/sec. The component fixation force has a fixed hook in the middle of the product, and therefore it is found that changes in the amount of byte for the fixed part do not result in significant improvements in the defect.

The objective of this study is to optimize the diameter of tubular shaft yoke and solid shaft yoke, which are the core components of Al IMS for xEV. The processes of both products were designed totally 6 steps to manufactured the shaft part and the yoke part. The diameter of solid shaft yoke and tubular shaft yoke were changed from 20mm to 25mm and from 30mm to 35mm, respectively. Al 6082 was applied to the material of both products. The friction condition between die and material was employed Oil_Cold (Aluminum) with reference to the library in the program. The results were analyzed and compared in terms of effective stress, effective strain, and nodal velocity characteristics. The effective strain value for manufacturing the yoke part was higher than the shaft part because its part has a complex geometry. The value of nodal velocity was also higher with high effective strain region. However, in 6 stage process of tubular shaft yoke, although it had the high effective strain value, the nodal velocity value was the lowest due to the piercing process. The effect of shaft part diameter on effective stress in the tubular shaft was difficult to observe, however, in the solid shaft yoke, when the shaft part of one increased, the effective stress value was increased due to the larger yoke size.

In this study, the effects of Sm addition (0, 0.05, 0.2, 0.5 wt%) on the microstructure, hardness, and electrical and thermal conductivity of Al-11Si-1.5Cu aluminum alloy were investigated. As a result of Sm addition, increment in the amount of α-Al and refinement of primary Si from 70 to 10 μm were observed due to eutectic temperature depression. On the other hand, Sm was less effective at refining eutectic Si because of insufficient addition. The phase analysis results indicated that Sm-rich intermetallic phases such as Al-Fe-Mg-Si and Al-Si-Cu formed and led to decrements in the amount of primary Si and eutectic Si. These microstructure changes affected not only the hardness but also the electrical and thermal conductivity. When 0.5 wt% Sm was added to the alloy, hardness increased from 84.4 to 91.3 Hv, and electric conductivity increased from 15.14 to 16.97 MS/m. Thermal conductivity greatly increased from 133 to 157 W/m·K.

Acidic soil significantly reduces crop productivity mainly due to aluminum (Al) toxicity. Alfalfa (Medicago sativa L.) roots were exposed to aluminum stress (Al3 +) in calcium chloride (CaCl2) solution (pH4.5) and root growth, physiological and antioxidant enzyme responses were investigated. The root growth (length) was significantly inhibited after 48 h of aluminum stress imposition. Histochemical staining with hematoxylin indicated significant accumulation of aluminum in Al stress-treated root tissues. Histochemical assay were also performed to detect superoxide anion, hydrogen peroxide and lipid peroxidation, which were found to be more in root tissues treated with higher aluminum concentrations. The enzymatic activity of CAT, POD and GR in root tissues was slightly increased after Al stress treatment. The result suggests that Al stress alters root growth in alfalfa and induces reactive oxygen species (ROS) production, and demonstrates that antioxidant enzymes involved in detoxification of Al-mediated oxidative stress.

It has been studied that the aluminum extrusion with the ingot-recycled composite billet that is casted. The billet is composed of the inner rod with the recycled and the outer ring with the ingot aluminum. For easy producing the tensile specimens to evaluate the bonding strength between recycled and ingot material, the extrusion die was designed. Two types of the billet are extruded. One is a composite billet that is casted. The other is an assembled billet with the turned bars. The strength is measured from tensile tests with extruded specimens. The effect on the strength of the oxidized layer between the materials has been researched with EDS analysis.

In order to analyze the effect of hot asymmetric rolling on the microstructure and texture of aluminum alloy and to investigate the effect of the texture on the formability and plastic anisotropy of aluminum alloy, aluminum 6061 alloy is asymmetrically rolled at room temperature, 200 ℃, 350 ℃, and 500 ℃, and the results are compared with symmetrically rolled results. In the case of asymmetric rolling, the equivalent strain (εeq) is greatest in the upper roll part where the rotational speed of the roll is high and increases with increasing rolling temperature. The increase rate of the mean misorientation angle with increasing temperature is larger than that during symmetrical rolling, and dynamic recrystallization occurs the most when asymmetrical rolling is performed at 500 ℃. In the case of hot symmetric rolling, the {001}<110> rotated cube orientation mainly develops, but in the case of hot asymmetric rolling, the {111}<110> orientation develops along with the {001}<100> cube orientation. The hot asymmetric rolling improves the formability (r) of the aluminum 6061 alloy to 0.9 and reduces the plastic anisotropy (Δr) to near zero due to the {111}<110> shear orientation that develops by asymmetric rolling.

To improve the mechanical properties of aluminum, graphene has been used as a reinforcing material, yielding graphene-reinforced aluminum matrix composites (GRAMCs). Dispersion of graphene materials is an important factor that affects the properties of GRAMCs, which are mainly manufactured by mechanical mixing methods such as ball milling. However, the use of only mechanical mixing process is limited to achieve homogeneous dispersion of graphene. To overcome this problem, in this study, we have prepared composite materials by coating aluminum particles with graphene by a self-assembly reaction using poly vinylalcohol and ethylene diamine as coupling agents. The scanning electron microscopy and Fourier-transform infrared spectroscopy results confirm the coating of graphene on the Al surface. Bulk density of the sintered composites by spark plasma sintering achieved a relative density of over 99% up to 0.5 wt.% graphene oxide content.

Salicylic acid (SA) is an essential plant growth regulator that functions as a signaling molecule in plants. The purpose of this study was to clarify how the exogenous application of SA counteracts aluminum stress-induced growth and biomass yield reduction in alfalfa exposed to aluminum (Al) stress. Two-week-old alfalfa seedlings were exposed to a combination of AlCl3 (0 μM, 50 μM and 100 μM, respectively) and SA (0.1 mM) for 72 hours. We observed, Al stress-induced plant growth inhibition and forage yield reduction are Al stress-dependent manner. A significant reduction of plant height (42.0-52.9%), leaf relative water content (13.0-21.4%), root length (35.4-48.7%), shoot fresh weight (31.2-25.9%), root fresh weight (15.4-23.3%), shoot dry weight (12.7-22.2%), roots dry weight (47.3 -53.5%), were observed in alfalfa. In contrast, SA alleviated the Al-stress and enhanced growth and biomass yield in alfalfa. This study provides useful information concerning the role of SA that counteracts aluminum stress-induced growth and yield reduction in alfalfa.