본 연구에서는 유도가열기법을 활용한 콘크리트 촉진 발열양생 기술의 효율성을 평가하기 위하여 철근 배근 및 전도체 변수에 따른 유도가열에 의한 콘크리트 온도향상 성능 및 압축강도를 평가하였 다. 먼저 철근 자체의 유도가열 성능을 평가한 결과, 주철근 및 나선철근 모두 유도가열 직후 10분 이 내에 목표온도인 70℃에 도달하여 충분한 가열성능을 나타내었다. 주요변수로 나선철근의 유무, 나선 철근의 간격, 피복두께, 거푸집 종류, 시험체 크기의 변수를 고려하여 15시간의 유도가열 발열양생 후 압축강도 평가를 실시하였다. 평가 결과, 철근을 포함한 경우 유도가열 발열양생 효율이 약 20~85% 만큼 증가하였다. 또한 총 6종(강섬유, 비정질강섬유, 전기로슬래그, 탄소섬유, 탄소나노튜브, 흑연나노 섬유)의 전도성 재료를 선정하여 재료 자체의 유도가열을 통해 발열성능을 평가하였다. 평가결과 강섬 유, 비정질강섬유, 전기로슬래그는 1~7분 사이에 가열 목표온도인 70℃에 근접하게 도달하여 유도가 열에 의한 콘크리트 발열성능을 향상 시킬 수 있는 혼입재료로 최종 선정하였다. 이상의 3가지 전도체 를 혼입하여 콘크리트를 타설한 뒤 15시간 유도가열 후의 압축강도를 평가한 결과, 강섬유 1%를 혼 입한 경우 발열양생을 실시하지 않은 상온양생에 비하여 강도가 186% 증가하였고, 잔골재의 50%를 전기로 슬래그로 치환한 경우 발열양생을 실시하지 않은 상온양생에 비하여 강도가 187% 상승하였다.

본 연구는 산업화 유망 식물인 회화나무의 이차대사산물 대량생산용 캘러스 확보에 필요한 기초조건을 확인하고자 수행하였다. 기내 배양한 회화나무 하배축을 2.0 mg·L-1 NAA + 0.1 mg·L-1 TDZ 배지에서 배양하였을 때 유백색의 부드러운 캘러스가 형성되었고, 캘러스 형성률 100±0.0%, 캘러스 형성에 걸리는 기간 7.1±0.03일, 캘러스 무게 249.8±12.73 mg으로 가장 효과적임을 확인하였다. 또한, 하배축에서 유도한 캘러스는 백색광 조건의 1.0 mg·L-1 IBA + 0.1 mg·L-1 TDZ 처리 배지에서 배양하였을 때 연노란색의 단단한 캘러스가 다량으로 형성되었고, 캘러스 생체중 186±5.4 mg, 면적 40.6±1.6 mm2으로 가장 무겁고, 크기가 우수한 것을 확인하였다. 기내 배양한 캘러스 소재 추출물의 추출수율은 50% 에탄올 추출 시 59%, 물 추출 시 54%로 확인하였고, 추출물 내 유효성분으로 마키아인 함량은 1.68 mg·g-1으로 검출되었다. 본 연구의 결과는 산업화 식물로써 유망있는 수종인 회화나무의 기내 대량증식과 이차대사산물 생산성을 향상할 수 있는 위한 기초자료로 활용할 수 있을 것이다.

백합 종간 교잡종은 다양한 교배 방법에 의해 생산되어지 고 있다. 그러나 이들 종간 교잡종은 대부분 불임이다. 2n gametes는 백합에서 종간 교잡종 F1의 불임을 극복할 수 있 을 뿐 아니라 우수한 유전형질을 지닌 2n과의 교배에 이용할 수 있고 후대 다양한 유전형질을 기대할 수 있다. 따라서 본 실험에서는 가장 효과적으로 2n gametes를 생산할 수 있는 방법을 구축하기 위하여 백합 Oriental hybrids ‘Medusa’와 ‘Marco Polo’에 N2O를 처리하였다. 같은 Oriental 그룹 내 에서도 ‘Medusa’와 ‘Marco Polo’는 화뢰 크기별 감수분열 시기가 달랐다. 감수분열 tetrad 시기에 염색체를 관찰한 결 과 sequential spindles, tripolar spindles에 의해 2가지 다른 형태가 관찰되었다. ‘Medusa’에서 2atm의 N2O를 처리 한 화뢰 길이 10~15mm와 20~25mm에서 monad, dyad, triad, tetrad가 관찰되었다. 그러나 4atm에서는 tetrad 이외에는 검경 되지 않았다. ‘Marco polo’의 경우 화뢰 길 이 10~15mm, 25~30mm 시기에 2, 4atm의 N2O를 12, 24 시간 동안 처리한 구에서 모두 dyad, triad가 관찰되었다. ‘Medusa’, ‘Marco Polo’ 모두 dyad, triad, tetrad가 관찰 된 시기는 대조구에서 interphase와 metaphase Ⅰ에 해당 하는 시기이다. 화분의 모양은 타원형으로 처리 전·후 변화가 없었으며 처리 후 화분의 크기는 n 보다 큰 화분뿐 아니라 작 은 화분도 관찰되어 전체적으로 다양했다. 화분의 임성과 발 아율은 처리구별로 차이가 없었으나 평균적으로 처리 후가 무처리구보다 임성은 약 10%, 발아는 약 20% 정도 떨어졌다. ‘Medusa’와 ‘Marco Polo’를 이용하여 N2O를 처리한 것과 처리하지 않은 것을 정역 교배하였을 때 자방이 비대 되는 형 태가 2가지이었으나 처리 별 차이는 아니었다. 획득된 식물체 를 Flow cytometry로 검정한 결과, 무처리 ‘Marco Polo’와 2atm 24시간 32mm에 처리한 ‘Medusa’의 교배를 통해 하 나의 식물체에서 2배체와 3배체가 모두 나오는 mixoploid를 확인할 수 있었다. 그 외 실험을 통해 얻은 식물체 중에서 이 수체가 4개 발견되었다. 확실한 3배체를 가진 식물체는 관찰 할 수 없었다.

본 연구는 대한민국 울릉도 특산식물인 추산쑥부쟁이(Aster × chusanensis Y.S.Lim, Hyun, Y.D.Kim & H.C.Shin)의 기내 대량증식체계 확립을 위해 시토키닌 계열 식물생장조절 제를 첨가하여 캘러스 및 신초 형성 조건을 구명하고자 수행 하였다. 실험결과, 추산쑥부쟁이의 줄기 절편체에서 캘러스 와 신초가 형성되었다. 캘러스 형성률은 TDZ 3.0mg·L-1처 리구에서 88.9%로 가장 높았고 BAP 3.0mg·L-1와 Zeatin 3.0mg·L-1 처리구는 66.7%, 2iP 3.0mg·L-1 처리구에서는 11.1%였다. 신초 형성률은 모든 처리구에서 77% 이상이고 특히 TDZ처리구와 Zeatin 처리구에서 100%였다. 그러나 TDZ처리구에서는 형성된 신초가 부풀어 오르거나, 잎에 과수 성이 나타나는 등 형태적 기형이 나타났다. Zeatin처리구에 서 발생한 신초는 정상적인 형태를 나타났다. 잎 절편체에서 는 캘러스, 신초가 발생하지 않았으며 절편체가 탈색하며 고 사하는 것을 확인하였다. 종합적으로 추산쑥부쟁이의 캘러 스 및 신초 형성을 위해서는 줄기 절편체를 배양 재료로 이 용하는 것이 효과적으로 확인되었다. 캘러스 유도에는 TDZ 3.0mg·L-1처리가 가장 효과적이었고, 추후 NAA와 같은 옥신 을 함께 첨가하여 증식 효과를 분석하는 연구가 필요할 것이 다. 또한, 신초 유도에도 TDZ 3.0mg·L-1 처리가 효과적이었 으나 장기간, 고농도로 사용할 경우 형태적인 기형이 발생할 수 있어 정상적인 식물생산에 부적합한 것으로 확인되었다. 따라서 형태적 기형이 발생하지 않은 아데닌 유도체형 시토키 닌인 Zeatin을 활용하는 것을 추천한다. 본 연구는 울릉도 특 산식물인 추산쑥부쟁이의 기내 대량증식과 생태계 유지에 필 요한 종 공급을 위한 대량증식 체계 구축을 위한 자료로 활용 할 수 있을 것이다.

The type of radioactive waste that may occur in the process of nuclear power plant dismantling can be classified into solid, liquid, gas, and mixed waste. The amount of these wastes must be defined in the Final Decommissioning Plan for approval of the licensing. Also, in the case of Metal radioactive waste, it is necessary to calculate the generation amount in order to treat radioactive waste at a Radioactive Waste Treatment Facility (RWTF). Since a large quantity of metal radioactive waste is generated during the decommissioning of a nuclear power plant, the application of a metal melter for reduction is considered. The metal waste is heated to a temperature above the melting point and separated into liquid and gas forms. Nuclides existing on the surface of metal waste vaporize in a melting furnace to become dust or collect in sludge. Nonvolatile nuclides such as Co, Fe and Mn remain in ingot, but other nuclides can be captured and reduced with dust and sludge. And the types of melting furnaces to be applied can be broadly classified into Atmospheric Induction Melter (AIM) and Vacuum Induction Melter (VIM). Therefore, this review intends to compare the two types of metal furnaces to be included in RWTF.

Working with molten metal has always been and will always be a dangerous workplace. No matter how carefully equipment is designed, workers are trained and procedures are followed, the possibility of an accident can occur in melting workplace. Some primary causes of melt splash and furnace eruptions include wet or damp charge material, dropping heavy charge into a molten bath, wet or damp tools or additives and sealed scrap or centrifugally cast scrap rolls. Induction melting brings together three things (water, molted metal and electricity) that have the potential for concern if the furnace is not properly working. Induction furnace must have a water cooling system built into the coil itself. Water picks up the heat caused by the current as well as heat conducted from the metal through the refractory. The water carries the heat to a heat exchange for removal. Spill pits serve to contain any molten metal spilled as a result of accident, run out or dumping of the furnace in an emergency. If a leak is suspected at any time, cease operation and clear the melt deck area of all personnel and empty the furnace. Molten metal fins can penetrate worn or damaged refractory and come into contact with the coil. A furnace or a close capture hood which suddenly swings down from a tilted position will cause injury or death. Whenever workers are working on a furnace or close capture hood when it is in the tilted position, be sure that it is supported with a structural brace that is strong enough to keep it from dropping if hydraulic pressure is lost. In theory refractory wear should be uniform, however, in practice this never occurs. The most causes of lining failure are improper installation of refractory material, inadequate sintering of refractory material, failure to monitor and record normal lining wear, allowing the lining to become too thin, installation of the wrong refractory, improper preheating of a used cold lining, failure to properly maintain the furnace the sudden or cumulative effects of physical shocks or mechanical stress, and excessive slag or dross buildup. Pouring cradles provide bottom support for crucibles. A crack in the crucible occur below the bottom ring support, the bottom of the crucible can drop and molten metal will spill and splash, possibly causing serious injury or death. To reduce this danger, a pouring cradle that provides bottom support for the crucible must be used. Power supply units must have safety locks and interlocks on all doors and access panels. Workers who work with low voltage devices must be made aware of the risk posed by high levels of voltage and current. The most causes of accidents are introduction of wet or damp material, improper attention to charging, failure to stand behind safety lines, coming into contact with electrically charged components and lack of operator skills and training. Only trained and qualified personnel are to have access to high risk areas. Safety lockout systems are another effective measure to prevent electrical shock

본 연구에서는 장미 시설재배 중에 나타나는 꽃목굽음현상(BPP, bent peduncle phenomenon)의 발생 양상을 이해 하고 증상 완화 방법을 알아보고자 하였다. 실험 계획은 BPP 를 인위적으로 유도하는 고온 처리와 BPP 증상을 완화하기 위한 비정상적인 꽃받침 제거 두 가지로 설계되었다. ‘Beast’ 대상 BPP 유도실험에서 화아분화 초기 BBS2단계(bud break stage 2, 신초길이 2±0.5cm)에 30℃ 이상 고온에서 쉽게 BPP가 유도되어 고온과 BPP의 연관성을 나타냈다. 또한 6품 종(‘Propose’, ‘Beast’, ‘Revue’, ‘Ocean Song’, ‘Iguana’) 을 대상으로 엽상화 꽃받침조각을 제거한 결과 BPP 완화에 미치는 효과는 품종 특이적이었으며, 품종에 따라 상이한 결 과를 보였다. 꽃받침조각 제거 처리로 BPP가 ‘Legato’와 ‘Revue’에서 유의하게 개선되었고, ‘Beast’와 ‘Iguana’에서 는 오히려 악화되었으며, ‘Propose’와 ‘Ocean Song’에서는 증상이 정지하여 효과적이었다.

Due to its excellent processability, thermal conductivity and high corrosion resistance, copper tubes applied to heat exchangers are being joined through brazing to increase heat exchange efficiency. In order to improve performance, the issue of joint quality of copper tubes, a major member of heat exchangers, is emerging, so research is needed to obtain excellent joint quality of brazing joints that may be damaged. In this study, the quality change of joints according to process variables was studied through induction heating brazing experiments using high frequency. The depth of penetration, which indicates the quality of the junction, was measured, and the center position of the high-frequency electrode and the height of the electrode, which change the location of the heat source applied to the junction, were selected as process variables. Lastly, the thermal image data obtained between the brazing experiments were obtained and the joint quality according to the temperature gradient of the joint was analyzed.

In this study, the stability of fishing boat inducing the change of fishing lamp in accordance with the installation of induction lamp in comparison with metal halide lamp was investigated. Inclining test for 8.55 ton class of hair-tail angling fishing boat was performed in order to find a GM and light weight. A stability calculation of the target fishing boat on the basis of KST-SHIP program was evaluated. The stability of the fishing boat with a metal halide lamp such as induction lamp according to the result obtained by the inclining test is slightly different, and the stability is not so much affected. Due to the induction lamp installation, the wind area increased by about 3.178 m 2 . Before installing the induction fishing lamp, G0M was found to be 0.209 at full load departure and 0.296 at departure from fishing ground. After installing the induction lamp, the full load departure condition is 0.178 and the fishing ground departure condition is 0.260. The G0M value before and after installation of the induction fishing lamp shows a difference of about 3% at the full load departure condition. The value of the critical angle of inclination definition showed a difference of about 16%. Despite these differences, it is lower than the regulations; it was confirmed that there will be no significant difference unless it is in an overloaded state.

In this study, we used underwater acoustics to analyze the spatial and temporal distribution characteristics of largehead hairtail (Trichiurus leptueus) based on the luminous thronging of metal halide fishing lamps and induction fishing lamps. As a result, the illuminating power was approximately 1.3 times higher using the metal halide fishing lamp whereas the density of hairtals by distance was approximately 1.9 times higher using the induction fishing lamp. Regarding water depth distribution, hairtails were detected depths of 25-30 m during August and at all water depths in November as assessed using fishing lamps.

An induction melting facility includes several work health and safety risks. To manage the work health and safety risks, care must be taken to identify reasonably foreseeable hazards that could give rise to risks to health and safety, to eliminate risks to health and safety so far as is reasonably practicable. If it is not reasonably practicable to eliminate risks to health and safety, attention have to be given to minimize those risks so far as is reasonably practicable by implementing risk control measures according to the hierarchy of control in regulation, to ensure the control measure is, and is maintained so that it remains, effective, and to review and as necessary revise control measures implemented to maintain, so far as is reasonably practicable, a work environment that is without risks to health or safety. The way to manage the risks associated with induction melting works is to identify hazards and find out what could cause harm from melting works, to assess risks if necessary – understand the nature of the harm that could be caused by the hazard, how serious the harm could be and the likelihood of it happening, to control risks – implement the most effective control measures that are reasonably practicable in the circumstances, and to review control measures to ensure they are working as planned.

Bulbophyllum auricomum Lindl. is a rare orchid and has flowers with an attractive fragrance. The present study investigated the tissue culture method for micropropagation. Capsules derived from artificial self-pollination were obtained for the best seed germination in MS basal medium. Plant growth regulators (1.0 mg·L-1 of BAP and 2.0 mg·L-1 of NAA) were affected by callus induction from subcultured pseudobulb explants. For the callus subculture, different natural plant extracts were tested in 11 treatment media. Among them, MS medium with 150 mL·L-1 of coconut water was generally effective in fresh weight (1.75 ± 0.08) and (3.01 ± 0.20) of callus proliferation and PLBs induction at 1 and 2 months, respectively, followed by an MS combination of 30 g·L-1 of banana and 20 g·L-1 of potato extract. The results of a comparative study of different MS mediums containing plant growth regulators with a natural extract combination and MS medium supplemented with natural extract only showed that MS medium supplemented with a combination of natural extracts (150 mL·L-1 of coconut water) and plant growth regulators (2.0 mg·L-1 of BAP and 1.0 mg·L-1 of NAA) obtained the highest shoot regeneration (3.37 ± 0.17) and (6.41 ± 0.68) after 1 month and 2 months of culturing, respectively.

All-trans retinoic acid (ATRA) is a derivative of vitamin A and exhibits anticancer activity against acute promyelocytic leukemia. Fenbendazole (FBZ) is a benzimidazole anthelmintic that has wide safety margin and low toxicity. Recently, FBZ has been found to have anticancer activity by destabilizing microtubules. In this study, we treat ATRA and FBZ on HL-60 cells, a human leukemia cell line, to investigate the synergistic effects of two drugs, and the potential anticancer mechanism. ATRA and FBZ significantly decreased the metabolic activity of HL-60 cells at 0.04 μM ATRA. Cell viability of ATRA-treated HL-60 cells decreased in a concentration-dependent manner and more decreased by FBZ. N-acetyl cysteine, an inhibitor of reactive oxygen species production, significantly increased the metabolic activity of the cells treated with ATRA and FBZ. Hoechst 33342 and propidium iodide staining showed the presence of broken nuclei in the HL-60 cells treated with ATRA and FBZ. And also, an apoptosis analysis demonstrated that 0.2 μM FBZ increased the percentages of cells in apoptosis and necrosis. In contrast, 0.04 μM ATRA showed no significant difference. Based on multiple assays, ATRA and FBZ showed not synergistic, but additive effect on HL-60 cells. This study may provide researchers and clinicians in cancer-related fields with some valuable information regarding the application of ATRA and FBZ.