The aim of this study is to evaluate the possibility of damage to cultural assets resulting from vibrations generated by construction vehicle traffic. The cultural heritage's natural vibration frequency was determined to be 150Hz by measurement. The damping ratios were calculated as 4.7% using the logarithmic decrement approach and 4.3% using the half-power method. The vibration measurements obtained during vehicle operation indicated that, despite an increase in vehicle velocity of up to 15 km/h, the vibrations remained below the detectable level of 0.13 mm/sec. When the road is curved and the terrain is sloped, a suitable speed for vehicle operation was found to be around 17 km/h, at which point vibrations were seen. The highest recorded vibration amplitude at this velocity was 0.217 mm/sec, which remains below the stringent regulation limit of 2 mm/sec. Thus, it can be concluded that there is no actual harm caused by vibrations.

해상풍력발전 시장의 성장과 함께 해상풍력발전기 설치 선 시장에 대한 기대감이 커지고 있다. 해상풍력발전 시장 내 2030년까 지 약 100척의 설치 선이 필요할 것으로 전망되고 있다. 척당 가격이 3,000∼4,000억 원이라서 일반 운반선보다 고부가가치 시장이다. 특 히, 풍력발전기 용량이 11MW 이상의 대형 설치 선의 수요가 커지고 있다. 중국을 중심으로 아시아 해상풍력발전기 시장의 급성장으로 이 지역에서 운용 가능한 설치 선에 대한 발주에 대한 협의가 많다. 아시아권역 대부분의 해저 지질은 지지 반력이 작은 점토층으로 구성되 어 있다. 이러한 특성에 의해서 설치 선이 작업을 위해 수면 밖으로 오르고 내림 시 스퍼드캔(Spudcan)과 레그(Leg)의 관입 깊이가 크게 발 생한다. 연구에서는 최소 3m에서 최대 21m까지 관입 변수를 이용하여 관입 깊이에 따른 고유 진동 주기, 레그의 구조 안전성 평가 그리고 전복 안전성 지수를 평가하였다. 관입 깊이가 증가하면 고유 진동 주기가 짧아지고, 레그의 모멘트 길이가 짧아져서 구조 강도의 여유 치 가 증가한다. 모든 입사각에서 전복 모멘트에 대해 안전하며, 최댓값은 270도에서 발생한다. 본 연구를 통하여 검토된 조건들은 연약 지반 에서 설치 선의 운용 절차서를 작성 시 관입 깊이에 따라서 레그를 어떻게 운용해야 하는지 판단할 수 있는 중요한 자료로 활용할 수 있 다. 결론적으로 관입 깊이에 따른 레그 구조 안전성을 정확히 파악하는 것은 설치 선의 안전과 직결된 문제이다.

A comparison and validation between the analysis and vibration test data of a nuclear fuel assembly were conducted. During the comparison and validation process, various parameters that govern the vibration behavior of the fuel assembly were determined, including nuclear fuel rod’s stiffness, spring constants of the dimple and spring of support structures, and damping coefficients. The calibration of the vibration analysis model aimed to find analysis parameters that can accurately simulate the vibration behavior of the test data. For calibration, power spectral density (PSD) diagrams were generated for both the measured signals from the test and the calculated signals from the analysis. The correlation coefficient between these two PSD plots was calculated. To find the analysis parameters, each parameter was defined as a variable with an appropriate range. Latin hypercube sampling was used to generate multiple sample points in the variable space. Analysis was performed for the generated sample points, and PSD plot correlation coefficients were calculated. Using the generated sample points and their corresponding results, a Gaussian Process Regression model was implemented for PSD plot correlation coefficients and the maximum PSD value. Based on the constructed surrogate model, the optimal analysis parameters were easily found without additional computations. Through this method, it was confirmed that the analysis model using the optimal parametes appropriately simulates the vibration behavior of the test.

이 논문에서는 보행교의 진동 사용성 평가에 있어서 보행자의 이동 질량 관성 효과의 고려 여부, 보행 패턴 등을 고려한 보행 시나 리오 등에 따른 해석 결과를 제시하고, 그에 따라 보행교 설계 단계에서 동적 유한요소 해석을 통한 진동 사용성 평가에 있어 적절한 해석 방법과 유의점을 제안한다. 지간 40m의 강합성 박스 단면을 갖는 단경간 단순교 형식의 보행교에 대하여 보행자 밀도, 보행 속 도, 임의 보행, 동기화 보행 등을 고려한 보행 시나리오에 대한 가속도 응답을 분석한다. 해석 결과 고정 질량 해석 방법은 임의 보행 시 나리오 해석에서 이동 질량 해석과 큰 차이를 보이지 않으며 진동 사용성 평가시에는 더 넓은 진동수 대역을 가진할 수 있는 임의 보행 시나리오를 고려하는 것이 바람직할 수 있음을 보였다.

A new lighting support structure composing of two-way wires and pulley, a pulley-type wireway system, was developed to improve the seismic performance of a ceiling type lighting equipment. This study verifies the seismic performance of the pulley-type wireway system using a numerical approach. A theoretical model fitted to the physical features of the newly-developed system was proposed, and it was utilized to compute a frictional coefficient between the wire and pulley sections under tension forces. The frictional coefficient was implemented to a finite element model representing the pulley-type wireway system. Using the numerical model, the seismic responses of the pulley-type wireway system were compared to those of the existing lighting support structure, a one-way wire system. The addition of the pulley component resulted in the increasement of energy absorption capacity as well as friction effect and showed in significant reduction in maximum displacement and oscillation after the peak responses. Thus, the newly-developed wireway system can minimize earthquake-induced vibration and damage on electric equipment.

Generally, vibration absorber systems are composed of spring-mass systems to reduce the vibration of a structure, and there are also methods to simply increase damping to achieve a damping effect across a wide frequency band. One similar method is to use a mechanism in which the eddy current is converted into a mechanical damping effect. When an eddy current is generated by electromotive force due to magnetic flux change, the reaction force is generated by the eddy current’s circulation. In this study, the damping system using the reaction force was constructed to reduce the transmission of vibrations generating from internal fluid and the vibration reduction characteristics that are transmitted externally were analyzed. As a result, 8.2 % of the vibration reduction effect from primary excitation frequency was confirmed.

Damping and sound absorption not only reduce environmental pollution caused by vibration and noise, but also improves processing accuracy, resolution of precision measuring instruments and fatigue life of machine parts in various precision machines. The vibration-damping plate is largely divided into a constrained type in which the resin is confined by a plate and a non-constrained type in which a plate is made of a polymer material mainly composed of polymer. The external vibration energy is absorbed by the thermal energy required for friction, stretching and compression of resin, so that the noise and vibration generated by resonance are reduced. The vibration damping ability of the sandwich plate produced in this study was found to be somewhat superior, which may be due to the difference in adhesive force during the manufacture of the sandwich plate. In the experimental results, it was confirmed that the sandwich plate material is superior to the vibration damping ability than the 5182 aluminum single plate material, it can be seen that the sandwich plate is effective for vibration damping of the aluminum alloy plate material.

Yangjindang house, which is located in Sang-ju province of South Korea, is one of the special Hanok structures dated back to Joseon dynasty. This study aims to examine structural safety of the Yangjindang wood frame building considering dynamic parameters such as the natural frequency and damping ratio. The numerical model of the wood frame building is implemented using Midas Gen, especially the wood joint where column and beam were connected. The behavior of the actual frame building was compared with the modeling results. In addition, structure responses such as shear force, axial force, flexural moment and deflections were calculated and compared with the allowable limits. Numerical results show that, generally, despite of some local members shear failure, Yangjindang’s structural response does not exceed the limitation according to current standards.

A base isolation system is widely used to reduce seismic responses of low-rise buildings. This system cannot be effectively applied to high-rise buildings because the initial stiffness of the high-rise building with the base isolation system maintains almost the same as the building without the base isolation system to set the yield shear force of the base isolation system larger than the design wind load. To solve this problem, the mid-story isolation system was proposed and applied to many buildings. The mid-story isolation system has two major objectives; first to reduce peak story drift and second to reduce peak drift of the isolation story. Usually, these two objectives are in conflict. In this study, a hybrid mid-story isolation system for a tall building is proposed. A MR (magnetorheological) damper was used to develop the hybrid mid-story isolation system. An existing building with mid-story isolation system, that is “Shiodome Sumitomo Building” a high rise building having a large atrium in the lower levels, was used for control performance evaluation of the hybrid mid-story isolation system. Fuzzy logic controller and genetic algorithm were used to develop the control algorithm for the hybrid mid-story isolation system. It can be seen from analytical results that the hybrid mid-story isolation system can provide better control performance than the ordinary mid-story isolation system and the design process developed in this study is useful for preliminary design of the hybrid mid-story isolation system for a tall building.

Recently, measuring instruments for SHM of structures had being developed. In general, the wireless transmission of sensor signals, compared to its wired counterpart, is preferable due to its absence of triboelectric noise and elimination of the requirement for cumbersome cable. However, the research on the tall buildings with relatively small vibration levels is insufficient. Therefore, in this paper, we used the wireless MEMS sensor and iPad to compare and analyze the vibration measurements of three tall buildings and two towers.

The identification of damping ratios in buildings is a well-known problem and appears to be of important and crucial interest in the safety and serviceability design. When compared to an estimation of the stiffness, i.e. natural frequency, and mass, the damping ratio is the most difficult quantity to determine. Many previous studies have examined the characteristics of damping ratios from ambient vibration, but the measurement time is roughly within 2 hours. In this paper, characteristics of damping ratios and natural frequencies of 4 story RC building were investigated using long-term ambient vibration. Free vibrations were obtained using random decrement technique, and damping ratios were evaluated by the envelop function, continuous wavelet transform, and logarithmic decrement. It was found that although the natural frequencies show little variations with time, the damping ratios show some variations with time and the largest variations found in the damping ratios obtained from the continuous wavelet transform. The damping ratios from the envelop function showed the smallest mean and standard deviation. And the probability distribution of damping ratios seems to follow the logarithmic normal distribution.

본 논문에서는 실제 공연장을 예제 건물로 하여 공연장에 발생한 진동을 측정한 결과를 바탕으로 공연장 구조물의 안전성에 대해 해석적으로 평가하였다. 수치해석 프로그램은 MIDAS GEN을 사용하였으며, 바닥판은 합성효과를 고려하여 모델링 하였다. 해석결과 진동계측실험을 통해 구한 바닥판 고유진동수와 유사한 결과를 보였다. 또한 군중의 율동에 의한 동적하중을 시간이력해석으로 해석하여 진동계측 실험과 유사한 수준의 바닥판 가속도 응답을 확인하였다. 이 모델을 사용하여 예제 공연장의 최대관람인원인 400명의 집단율동 시 발생하는 상황에 대하여 분석하였다. 그 결과 기둥과 보의 가해지는 외력은 설계 내력을 하회하여 안전성에 문제없음을 확인하였다. 또한 공연 시 발생하는 수평방향 진동수준은 지진하중의 2% 수준으로 수직수평 모두 안전성에 문제가 없는 것을 확인하였다.

Recently, measuring instruments for SHM of structures had being developed. In general, the wireless transmission of sensor signals, compared to its wired counterpart, is preferable due to its absence of triboelectric noise and elimination of the requirement for cumbersome cable. Preliminary studies on the continuous vibration measurement of high-rise buildings using MEMS sensors have been carried out. However, the research on the low-rise buildings with relatively small vibration levels is insufficient. Therefore, in this paper, we used the wireless MEMS sensor to compare and analyze the vibration measurements of three low-rise buildings.

본 연구에서는 초고층건축물의 풍진동 모니터링을 위한 시스템식별기법의 현장적용성을 평가하였다. 실제 아웃리거-벨트월 을 횡력저항 시스템으로 가지는 실제 63층 RC구조물을 대상으로 상시 및 강풍시 응답을 모니터링하였으며, 진동수영역분해(FDD), 랜덤감소(RDT)기법, 부분공간시스템식별(SSI)법을 사용하여 진동특성을 식별하였다. 건물의 평면이 정방형이고, 두 개의 횡방향 모드의 진동수는 매우 유사하였다. 모든 식별기법에서 태풍과 같이 강한 외력이 존재할 경우 뿐만 아니라 상시미진동 에서도 구조물의 모드 특성을 식별할 수 있었다. 현장에서의 적용성 평가결과, 계산속도는 FDD가 가장 빨랐으며, RDT가 가장 간단한 프로그래밍 절차를 가지고 있음을 확인하였다.

The market for Game is gradually expanding every year, but most of games are disappearing. For this Reason, User have chosen games based on external factors, and users have been not able to choose customized games for users. Thus, This study aim to provide customized game contents to users among 6 content (logic, space, word, nature, body, music) by making a immersion evaluation model using the Csikszentmihalyi’s theory of flow and Gardner's theory of multiple intelligence. First, it is assumed that the definition of immersion can be obtained as an arousal which is an axis of the emotion criterion. Then, after learning the arousal classification model based on the head micro-vibration as emotion signal, the immersion evaluation system is verified through the evaluation with the multi-intelligence theory. As a result, the user can be informed of what contents are most immersed in the content, and allow to choose the game suitable for himself.

Recently, with development of city traffic network planning, there are various effects with living space from vibration of railway. But, study which about effect from vertical vibration in floor slab in nearing structure is lack in nowadays. This thesis have analysed result from acceleration response per distance as well as proceed with serviceability evaluation and extracted natural frequency from measuring vibration of railway using mobile phone application which is oriented for building which have distances about 5m to 22m from railway.

Cooling towers have been widely applied to control the indoor temperature in the residential area and the living space. At operating the cooling towers, motor, fan and dropping water produce noise and vibration, which diffuse through the air or the solid object, polluting the environment. The standards can be used at estimating noise and vibration emission by showing remarkable economic or social benefits. The purpose of this study is to show the vibration and noise measurement and influence evaluation between cooling towers and semiconductor equipment.