In this study, we learned about the effects of indoor radon concentration reduction associated with the operation of a mechanical ventilation system at an apartment house. The experimental parameters were mainly the indoor radon level and air change rate, which were controlled by the amount of emissions released and fan motor speed. Even at the high level of radon diffused in an apartment house, indoor radon concentrations converged to the Korean national guideline level within 3 to 4 hours when the air was ventilated at 0.5 ACH and 0.7 ACH. In the case of 0.3 ACH, however, where the degree of ventilation was insufficient compared to the legal air change rate, the high concentration indoor radon could not be sufficiently removed even if the mechanical ventilation system was operated for more than 14 hours continuously. When the indoor radon level was high, the reduction rate was 34.3% for 0.3 ACH, 70.4% for 0.5 ACH, and 69.7% for 0.7 ACH at 6 hours-operation, while at the medium-level, indoor radon can be reduced by 46.2% (0.3 ACH) to 73.2% (0.7 ACH). Depending on the indoor concentration range, it may be required to secure a ventilation rate of 0.5 ACH or more at all times. In addition, in apartment houses with excellent airtight performance, even if indoor radon is at a level similar to the national guideline, it is difficult to expect a reduction in the concentration due to natural decay. Therefore, it is desirable to lower the indoor concentrations as much as possible.

Hong, Dae-Yong manufactured the Tongcheon-ui (Pan-celestial Armillary Sphere) with cooperating clock researcher Na, Kyeong-Jeok, and its craftsman An, Cheo-In, in Naju of Jeolla Province in 1760 ~ 1762. Tongcheon-ui is a kind of astronomical clock with an armillary sphere which is rotated by the force generated by a lantern clock’s weight. In our study, we examine the lantern clock model of Tongcheon-ui through its description of the articles written by Hong himself. As his description, however, did not explain the detail of the mechanical process of the lantern clock, we investigate the remains of lantern clocks in the possession of Korea University Museum and Seoul National University Museum. Comparing with the clocks of these museums, we designed the lantern clock model of Tongcheon-ui which measures 115 mm (L) × 115 mm (W) × 307 mm (H). This model has used the structure of the striking train imitated from the Korea University Museum artifact and is also regulated by a foliot escapement which is connected to a going train for timekeeping. The orientation of the rotation of the going train and the striking train of our model makes a difference with the remains of both university museums. That is, on the rotation axis of the first gear set of Tongcheon-ui’s lantern clock, the going and the striking trains take on a counterclockwise and clockwise direction, respectively. The weight of 6.4 kg makes a force driving these two trains to stick to the pulley on the twine pulling across two spike gears corresponding to the going train and the striking train. This weight below the pulley may travel down about 560 mm per day. We conclude that the mechanical system of Tongcheon-ui’s lantern clock is slightly different from the Japanese style.

위험유해물질(HNS, Hazardous and Noxious Substances)은 해상운송 과정에서 다양한 사고에 노출되어 있어 많은 양이 바다에 유출 될 우려가 있다. HNS 유출에 따른 해양환경의 손상은 유류 유출에 의한 손상보다도 훨씬 큰 것으로 알려져 있다. 특히 해저로 침강하여 침적되는 HNS는 해저생태계에 돌이키기 어려운 피해를 주게 되므로, 반드시 회수되어야 한다. 해저로부터 HNS를 회수하기 위해서는 해저침적 HNS에 대한 정확한 탐지, 안정화 처리 및 회수를 위한 절차와 장비가 필요하다. 그 중에서도 기계적 회수장치를 개발하기 위해서는 성능지표를 이용하여 성능요건을 선정하고, 이를 토대로 기계적 회수장치에 대한 개념설계가 이루어져야 한다. 따라서 본 연구에서는 해저침적 HNS의 회수 절차에서 요구되는 기계적 회수장치에 대한 개념설계안을 제시하였다. 개념설계안으로 해저침적 HNS를 회수하기 위한 기본 시나리오를 제시하고, 자체적 밀폐 성능을 가지는 흡인 기초를 활용하는 방안을 채택하였다. 기계적 회수장치는 흡인 기초, 오 염 방지, 펌프 시스템, 제어 시스템, 모니터링 장비, 위치정보 장비, 이송 장비, 탱크로 구성된다. 이러한 개념설계안은 기계적 회수장치의 부품 및 형상을 결정하는 기본설계에 반영되어 활용될 것으로 기대된다.

해상을 통하여 운송되는 화학물질은 6,000여종에 이르며, 이러한 화학물질에는 해양을 오염시키거나 해양생물에 해로운 HNS(Hazardous and Noxious Substances)가 포함되어 있다. 해상운송 과정에서 바다로 유출된 HNS는 해상 및 해중에서 물리적, 화학적 변화 를 거치게 되는데, 어떤 종류의 HNS는 해저로 침강하여 퇴적되기도 한다. 해저에 침적된 HNS는 해저생태계에 커다란 악영향을 주기 때문에 해저침적 HNS를 탐지․처리하여 회수하는 것이 바람직하다. 따라서 본 연구는 해저침적된 HNS를 회수하기 위한 기계장치를 개발할 때, 최우선으로 고려해야 하는 성능요건을 제시하였다. 해저의 오염물질을 회수하기 위하여 현재 사용되는 다양한 방식의 준설장비에 대하여 조사하고, 준설장비의 방식별 성능지표를 분석함으로써 기계장치에 대한 10가지의 성능지표를 선정하였다. 이러한 성능지표를 활용하여 해저침적 HNS 회수용 기계장치의 개발을 위한 성능요건을 제안하였다. 국내 항만의 수심을 고려하여, 해저침적 HNS 회수용 기계장치 의 성능요건을 생산율(50 ~ 300 m3/hr), 최대운용수심(50 m), 저질 종류(대부분의 저질 형태), 고형률(10 % 이상), 수평 작업 정확도(± 10 cm), 제한 유속(3 ~ 5 knot) 등으로 제안하였다. 이러한 성능요건은 해저침적 HNS 회수용 기계장치의 개념설계와 기본설계에 활용될 것으로 기 대된다.

구조와 사육환경이 동일한 3개의 돈방(room A~C)에서 48일 동안 비육돈의 암모니아 농도 및 환기량을 모니터링하여 배출계수를 산정하였다. 실험 결과, 온도 22.5℃, 습도 53.9% 환경에서 평균 암모니아 순발생 농도 5.93 ppm, 환기량 23.7 m3/h·pig로 나타났다. 일별 상관관계 분석결과, 암모니아 농도는 온도와 음의 상관관계(R2: -0.65 ~ -0.53)를 가지는 것으로 나타났으며, 환기량은 암모니아 농도에 거의 영향을 미치지 않는 것으로 나타났다. 암모니아 농도는 이른 오전을 기점으로 서서히 증가 경향을 보이다가 12~13시경 최댓값에 도달하였고, 상호 상관도가 높은 온도, 습도, 환기량의 경우 14~15시에 최댓값을 갖는 것으로 분석되었다. 시간별 데이터 상관관계 분석결과, 암모니아 배출량에 영향을 미치는 요소는 암모니아 농도(R2=0.71)와 환기량(R2=0.61)으로 이 중, 암모니아 농도가 더 상관성이 높은 것으로 분석되었다. 암모니아 배출계수는 2.28 g/d·pig로 분석되었다.

The annealing characteristics of cold-rolled Al-6.5Mg-1.5Zn-0.5Fe-0.5Mn alloy, newly designed as an automobile material, are investigated in detail, and compared with those of other aluminum alloys. Using multi-pass rolling at room temperature, the ingot aluminum alloy is cut to a thickness of 4 mm, width of 30 mm, and length of 100 mm to reduce the thickness to 1 mm (r = 75 %). Annealing after rolling is performed at various temperatures ranging from 200 to 500 oC for 1 hour. The specimens annealed at temperatures up to 300 oC show a deformation structure; however, from 350 oC they have a recrystallization structure consisting of almost equiaxed grains. The hardness distribution in the thickness direction of the annealed specimens is homogeneous at all annealing temperatures, and their average hardness decreases with increasing annealing temperature. The tensile strength of the as-rolled specimen shows a high value of 496 MPa; however, this value decreases with increasing annealing temperature and becomes 338MPa after annealing at 400 oC. These mechanical properties of the specimens are compared with those of other aluminum alloys, including commercial 5xxx system alloys.

The characteristics of ammonia during the growing period of pigs in a facility with a mechanical ventilation system were analyzed, and the emission factor was calculated. Real-time ammonia concentration was measured using photoacoustic spectroscopy equipment, and a ventilation measuring device was fabricated to measure the amount of air vented from an exhaust fan according to the operation rate. All data were collected as one-hour averages. The mean ammonia concentration, indoor temperature, and ventilation rate was 1.44~2.08 ppm, 25.5~26.4oC, and 24~32 m3/h per pig, respectively. Both concentration and ventilation rate are important factors in terms of emission management, but correlation analysis shows that the impact of concentration is higher than that of ventilation. Using ammonia concentration and ventilation data, the ammonia emissions per pig were calculated by considering the number of pigs (0.25~1.74 g/day·pig). The final ammonia emission factor yielded a value of 0.81 g/day·pig.

Synthesis of composite powders for the Fe2O3-Zn system by mechanical alloying (MA) has been investigated at room temperature. Optimal milling and heat treatment conditions to obtain soft magnetic composite with fine microstructure were investigated by X-ray diffraction, differential scanning calorimetry (DSC) and vibrating sample magnetometer (VSM) measurement. It is found that α-Fe/ZnO composite powders in which ZnO is dispersed in α-Fe matrix can be obtained by MA of Fe2O3 with Zn for 4 hours. The change in magnetization and coercivity also reflects the details of the solid-state reduction process of hematite by pure metal of Zn during MA. Densification of the MA powders was performed in a spark plasma sintering (SPS) machine at 900 ~ 1,000 ℃ under 60 MPa. Shrinkage change after SPS of sample MA'ed for 5 hrs was significant above 300 ℃ and gradually increased with increasing temperature up to 800 ℃. X-ray diffraction results show that the average grain size of α-Fe in the α-Fe/ZnO composite sintered at 900 ℃ is in the range of 110 nm.

The activation energy to create a phase transformation or for the reaction to move to the next stage in the milling process can be calculated from the slop of the DSC plot, obtained at the various heating rates for mechanically activated Al-Ni alloy systems by using Kissinger's equation. The mechanically activated material has been called “the driven material” as it creates new phases or intermetallic compounds of AlNi in Al-Ni alloy systems. The reaction time for phase transformation by milling can be calculated using the activation energy obtained from the above mentioned method and from the real required energy. The real required energy (activation energy) could be calculated by subtracting the loss energy from the total input energy (calculated input energy from electric motor). The loss energy and real required energy divided by the reaction time are considered the “metabolic energy” and “the effective input energy”, respectively. The milling time for phase transformation at other Al-Co alloy systems from the calculated data of Al-Ni systems can be predicted accordingly.

Coupling is commonly used as a mechanical fastener to connect the turbine housing and the bearing housing in a turbocharger assembly. The finite element analysis was used to predict the structural behaviors of the coupling system, which could be caused by the bolt clamping force in the assembly process and the thermal deformation during turbocharger operation. The back plate is used to prevent gas leakage from the turbine housing to the bearing housing while the fixed pin is inserted to set the reference position between the two parts. Thus, in order to predict the mechanical behaviors of the coupling system numerically, the temperature distributions were calculated by heat transfer analysis based on the rated speed of the diesel engine. As a result of analyzing the structural characteristics of the turbocharger, the contact pressure of the back plate was influenced by thermal deformations whereas the bending deformation of the fixed pin was affected by the thermal deformation and the pin position.

In this study, an Al-0.7wt%Fe-0.2wt%Mg-0.2wt%Cu-0.02wt%B alloy was designed to fabricate an aluminum alloy for electrical wire having both high strength and high conductivity. The designed Al alloy was processed by casting, extrusion and drawing processes. Especially, the drawing process was done by severe deformation of a rod with an initial diameter of 12 mm into a wire of 2 mm diameter; process was equivalent to an effective strain of 3.58, and the total reduction in area was 97 %. The drawn Al alloy wire was then annealed at various temperatures of 200 to 400 °C for 30 minutes. The mechanical properties, microstructural changes and electrical properties of the annealed specimens were investigated. As the annealing temperature increased, the tensile strength decreased and the elongation increased. Recovery or/and recrystallization occurred as annealing temperature increased, and complete recrystallization occurred at annealing temperatures over 300 °C. Electric conductivity increased with increasing temperature up to 250 °C, but no significant change was observed above 300 °C. It is concluded that, from the viewpoint of the mechanical and electrical properties, the specimen annealed at 350 oC is the most suitable for the wire drawn Al alloy electrical wire.

Polymer electrolyte membrane (PEM) is one of key elements to determine both electrochemical performances and lifetimes of fuel cell electric vehicles (FCEVs). PEM is exposed to a variety of dynamic stimuli (e.g., temperature, humidity, pressure, fuel gases and so on) under their operation conditions and meets unavoidable mechanical damages derived from unequal pressure difference between anode and cathode feed gases. Even though there have been approaches to evaluate the mechanical strength of PEM materials, most of the trials could provide static information on their mechanical strength. In this study, a pressure-loaded blister hybrid system connected with gas chromatography was developed to disclose the efficacy of the system as an evaluation tool of dynamic PEM strength under realistic FCEV operation conditions.

The study seeks to cooperate with the investigation of a fire investigation based on public-private partnership. Fire protection systems provide a wide variety of viewpoints from the perspectives of design, construction, management, maintenance, maintenance and maintenance systems at a particular point in time, construction, management, and maintenance systems. What is controversial is that there are illegal activities such as illegal activities of the Patent Office, misconduct of construction work and unreasonable construction of construction works.As a theoretical framework, the present study identified the four key elements of a successful disaster response system : responsiveness, control, professionalism, and bias.

As the demand for automation (or autonmation) or clean workplace has grown, the interest in the knowledge and skill regarding safety is rising in manager duty. Moreover, the importance of severity rate of injury has increased due to the enlargement of industry scale, even safety management area has developed. Thus, it is important that production managers, the core of the line process, realize the safety in their production line, even if a safety manager acts as a staff. However, in the duty oriented National Competency Standard (NCS), the education about the safety duty of production management part is insufficient. According to NCS, it is calculated production managers receive only 6.7% of whole safety education regarding the duty related the safety management for production manager in mechanical industry. However, the ability in safety is more demanded from production managers as the concept of “production and safety” turns into the concept of “production with safety”. And then in this paper, we will compare and analyze the safety management duty in Korean NCS and the safety management duty in State Leaders Connecting Learning to Work in US manufacturing industry, in terms of the duty of the production manage in mechanical industry (05). And, we will develop the safety duty education system for production manager, by classifying the safety education in domestic mechanical industry into knowledge education, skill education, and attitude education with using AHP(Analytic Hierarchy Process).

The cold rolling workability and mechanical properties of two new alloys, designed and cast Al-5.5Mg-2.9Si and Al-7Mg-0.9Zn alloys, were investigated in detail. The two alloy sheets of 4 mm thickness, 30 mm width and 100 mm length were reduced to a thickness of 1 mm by multi-pass rolling at ambient temperature. The rolling workability was better for the Al-7Mg-0.9Zn alloy than for the Al-5.5Mg-2.9Si alloy; in case of the former alloy, edge cracks began to occur at 50% rolling reduction, and their number and length increased with rolling reduction; however, in the latter alloy, the sheets did not have any cracks even at higher rolling reduction. The mechanical properties of tensile strength and elongation were also better in the Al-7Mg-0.9Zn alloy than in Al-5.5Mg-2.9Si alloy. Work hardening ability after cold rolling was also higher in the Al-7Mg- 0.9Zn alloy than in the Al-5.5Mg-2.9Si alloy. At the same time, the texture development was very similar for both alloys; typical rolling texture developed in both alloys. These differences in the two alloys can primarily be explained by the existence of precipitates of Mg2Si. It is concluded that the Al-7Mg-0.9Zn alloy is better than the Al-5.5Mg-2.9Si alloy in terms of mechanical properties.

PURPOSES: This study is to investigate the mechanical performance of the fiber reinforced lean concrete with respect to different types of fibers. METHODS: Increased vehicle weight and other causes from the exposed conditions have accelerated the deteriorations of road pavement. A new multi-functional composite pavement system is being developed recently in order to extend service life and upgrade the pavement. A variety of tests were conducted before and after hardening of the concrete. RESULTS: From the test results, it was found that the use of different types of fibers did not affect the compressive strength development. This might be due to the inherent property of the lean concrete. When steel fibers were used relatively greater flexural strength and flexural fracture toughness were developed. Also addition of fly ash by replacing a part of Portland cement the fracture toughness was slightly increased. CONCLUSIONS: It has been known that the addition of fibers and use of mineral admixture can be positively considered in the development of multi-functional composite pavement system as its required mechanical performance is obtained.

Metallic compound of ternary Al-B-C system was prepared by mechanical alloying (MA) using Al, boron and graphite powders as starting materials. MA was carried out using Spex 8000 mixer/mill for 50 hours in an argon atmosphere without process control reagent such as methyl alcohol. The MA powders obtained were heat-treated in vacuum at the temperature of 873 and 1273 K for 5 hour. Pure ternary Al-B-C compound was obtained in the chemical content of Al:B:C=55:27:18. The ternary compound obtained in this study has a new phase whose crystal structure is not identified yet.